MODEL : LK-P35B MOBILE PRINTER All specifications are subject to change without notice Table of Contents 1. Product Overview 2. Unpacking 3. Setting up the Product 3-1. Installing Battery 3-2. Battery Charging 3-3. Loading the Media 3-4. Black Mark 3-5. Printer Case Usage 3-6. Control Panel 3-7. Self Test 4. Peripherals Connection 4-1. Bluetooth Connection 4-2. Interface Cable Connection 5. Printer Specification 3 4 5 5 6 7 8 9 10 11 12 12 13 14 1. Product Overview Power button Paper feed button SERIAL DC POWER Battery cover open button 2 3 2. Unpacking 3. Setting up the Product 3-1. Installing Battery PRINTER BATTERY SERIAL CABLE RECHARGER ROLL PAPER CD MANUAL 1. Align the battery hook as shown in the picture. 2. Push the battery into the printer until it locks in place. Notes As the battery is not charged at the time of your purchase, charge the battery prior to using the printer. PRINTER CASE(OPTION) 4 5 3-2. Battery Charging 3-3. Loading the Media Press the cover open button. Place the paper roll as shown in the picture.
(Make sure the paper is placed in right direction.) 1 2 3 4 1. The battery can be charged only when the temperature is 0~40C. 2. Be sure that the printer is turn off and the battery to be charged is installed. 3. Connect the charger to the printer. 4. Recharging will now be started. Notes 1. Do not turn on the printer power while you are charging the battery. 2. Dot not print while charging the battery 3. Do not connect the charger to the printer on the process of printing. 6 Pull a short length of paper out of the printer and close the cover as shown in the picture. Press feed button and let the paper be arranged properly for printing and cut the extra paper with tear bar. 7 3-4. Black Mark 3-5. Printer Case Usage Open the Velcro. Put the printer into the case following the direction as shown in the picture. 1 2 3 4 Notes Black mark should be located on the opposite side of the printed side of the media. 8 9 Close the Velcro. Fix this case to the belt with using the belt buckle. 3-7. Self Test You can check the printer setting state by doing self test when you set the printer rst time or encounter some problems.
- Control Circuit, Mechanisms, Print Quality, Rom version. When you can not nd the exact cause of problem through self test, investigate on other hardware parts or software. This function is independent of other devices and software. Self Test Instructions 1.Turn the printer power off an close the printer paper cover. 2. While pressing the paper feed button, turn on the printer power. 3. The printout is producing 4. To add a printout of the Hex-Dump mode, press the paper feed button once more. 5. To add a printout of ASCII pattern, press the paper feed button once more.
(Without pressing the paper feed button, self test ends automatically) 6.After ASCII pattern printing, self test ends automatically.
< Sample printout of Self Test> >
3-6. Control Panel Button Name function This button is used to turn the printer on and off. When the printer is off, press this button for approximately 2 seconds and it will turn on the power. When you press this button in a state that the printer is on, the printer will turn off. Paper output can be done manually by pressing this button. Additionally, self-testing and Hexadecimal Dumping can be processed.. 1. Refer to 3-10 for self test information. 2. Refer to the service manual regarding Hexadecimal Dumping. 1. If the Batt, LED are Lit, the battery is fully charged. 2. If you can hear beeping sound and LED light is turned off, it means that the battery is at the lowest level. 3. If the battery is not charged at all, the printer turns off automatically. If the red light is turned on, it means that the paper cover is open. Power button Paper Feed Button Battery Status Lamp Error Lamp
**Sleep Mode**
After 3 minutes without working, it changes to sleep mode automatically. Input Uart or serial data of Bluetooth. Notes The first 200mss data between sleep mode and warming-up could be ignored. 10 11 4. Peripherals Connection This product can communicate with other devices via Bluetooth communication and cable. 4-2. Interface Cable Connection 4-1. Bluetooth Connection 1. The printer can be connected to devices equipped with Bluetooth communication capacity
(PDA, PC, etc.). 2. Use the Bluetooth connection function supported by the device to connect to the printer. Classifications Bluetooth Spec. Frequency Baudrate Data bit Parity bit Stop bit Description Bluetooth V2.0 / Class2(10m) 2.4GHz ISM BAND 115200bps Fixed. 8 Data bit Fixed. No parity Fixed. 1 Stop bit Fixed. Serial 1. Connect the Interface cable (Serial / USB) to the cable connector of the printer. Notes Use only cables provided by this manufacturer 2. Connect the interface cable to the USB or Serial port of the device (PDA, PC, etc) 12 13 Dimension WXDXH(mm) 106X100X49.5 WXDXH 3.7X5.3X2.2 Weight Temperature Operating Storage Humidity Operating Storage 0.3kg 5~40
-20~60 35 ~ 80%
10 ~ 90%
5. Printer Specification Printing Method Printing Speed Resolution Character Size Character per Line Character Set Barcode Emulation Driver Sensor Paper Direct Thermal 60mm/sec 203 DPI X 203 DPI Font A (12X24), Font B (9X24) Font A : 48pt , Font B : 64pt ALPHA NUMERIC Caractor, Extension Caractor EAN-8, EAN-13, Code39, ITF, UPC-A, Codabar, Code93, Code128, PDF417(2D) ESC/POS Window CE 4.2&5.0, Window Mobile 5.0 Type Width Thickness Paper End Sensor Thermal Paper 80mm 65 Roll Diameter Max. 45mm Roll Core Inner Diameter 12.5mm +/-0.5mm Reliability Interface TPH Battery Standard Option 50km Continues printing(40mm/sec) 40 ~ 50 mimutes Waiting: 11 hours Serial(RS-232C) Bluetooth Class2 Battery Recharger Input AC100~240V, 50/6 Hz battery Output Type Output 8.4V , 800~1200mAh Li-on 7.2V, 1200mAh Charging time 2~3 Time 14 15 SEWOO TECH CO.,LTD. ADDRESS Doosung Bd, 689-20, Kumjung-dong, Kunpo-si, Kyunggi-do, Korea TEL 82-31-459-8200 FAX 82-31-459-8880 URL http://www.miniprinter.com Rev. 1.0