FCC ID: NDPC10-1R POS Terminal

C10-1R Quick Start Guide 10.1 Touch Panel Identifying Components Printer Door Fingerprint

(optional) Printer Door Release Button MSR (optional) Feed Button IC Card Reader

(optional) Power Switch*

USB Kensington lock Federal Communications Commission (FCC) Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING The system uses a 3V CR2032 battery mounted on the mainboard to keep time. There is a risk of explosion if the wrong battery type is used when replacing. Dispose of used batteries according to local ordinance regulations. WARNING This is Class A Product. In domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

CCC VCCI Information VCCI-A NCC

Safety information Before installing and using the machine, take note of the following precautions:

Do not place the unit on an unstable surface, cart, or stand. Do not block the slots and opening on the unit, which are provided for ventilation. Only use the power source indicated on the marking label. If you are not sure, contact your dealer or the Power Company. When replacing parts, ensure that your service technician uses parts specified by the manufacturer. Do not place anything on the power cord. Place the power cord where it will not be in the way of foot traffic. FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. RFID

(optional) USB Micro SD Card LINE OUT LAN USB COM COM DC-in Jack USB COM COM Cash Drawer HDMI Specification Item C10-1R Display Touch CPU Memory Storage 10.1, Resolution 800 x 1280 PCAP touch Rockchip RK3568 DDR4 4GB Emmc64GB + 1x Micro SD Card Slot External I/O 4 x USB 3.2 + 2 x USB 2.0 Interface 4 x Serial ports, RS232 (RJ45), 0V/5V/12V selected in UI

(COM1, COM2, COM3, COM4) 1 x LAN, (IEEE 802.3 10/100/1000 Mbps Ethernet, RJ45) 1 x RJ11 port supports 2 cash drawers with 24V / 12V by jumper setting 1 x Audio (1 x line out) 1 x HDMI 2.1 1 x DC +24V input 1 x Micro SD card 1 x Speaker 3W 3" Thermal printer Speaker Printer Optional Peripheral MSR (Beep), IC Card Reader, Fingerprint, RFID 2D Bar Code Scanner 5M Camera CD-101C Display Support 2 Independent Displays (Main Display + CD-101C or HDMI) Spill & Dust resistant N/A Operation System Android 12 SW N/A Power Adaptor AC-In 100~240V / DC-Out 24V,72W Reliability System Operating Temperature:0~40C System Humidity: 15% ~ 80%

Storage Temperature: -20~60C Dimensions 262.26 (W) x 291.77 (H) x 247.13 (D) mm Weight 3.3 Kgs

Part name POS Terminal (/) Model /C10-1R

/ / Hazardous substances' name

(Pb)

(Pb)

Lead(Pb) and its compounds

(Hg)

Mercury(Hg) and its compounds

(Cd)

(Cd)

Cadmium(Cd) and its compounds

(Cr6+)

(Cr6+)

Hexavalent chromium

(Cr6+) and its compounds

(PBB)/

(PBB)/

Polybrominated biphenyls

(PBB)

(PBDE)/

Polybrominated diphenyl ethers

(PBDE)

/ /Plastic Shell

/ /Speaker

/ /LCD Panel

/ /Circuit board

//Power Cable

// Other Wire 1. 2. SJ/T 11364 GB/T 26572 GB/T 26572

This table is prepared in accordance with the provisions of SJ/T 11364. Indicates that said hazardous substance contained in all of the homogeneous materials for this part is below the limit

requirement of GB/T 26572. Indicates that said hazardous substance contained in at least one of the homogeneous materials used for this part is above the

limit requirement of GB/T 26572. CE RF Feature RF Spec. NFC

/Contact Information Frequency Range 13.56MHz Max. Output Power (dBm) NA

/Partner Tech Corporation 233110 10F., 233-1, Baoqiao Road, Xindian, New Taipei City 231, Taiwan Phone: +886-2-29188500 http://www.partner.com.tw/

C14-1R Quick Start Guide 14.1 Touch Panel Identifying Components Printer Door Fingerprint

(optional) Printer Door Release Button MSR (optional) Feed Button IC Card Reader

(optional) Power Switch*

USB Kensington lock Federal Communications Commission (FCC) Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING The system uses a 3V CR2032 battery mounted on the mainboard to keep time. There is a risk of explosion if the wrong battery type is used when replacing. Dispose of used batteries according to local ordinance regulations. WARNING This is Class A Product. In domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

CCC VCCI Information VCCI-A NCC

Safety information Before installing and using the machine, take note of the following precautions:

Do not place the unit on an unstable surface, cart, or stand. Do not block the slots and opening on the unit, which are provided for ventilation. Only use the power source indicated on the marking label. If you are not sure, contact your dealer or the Power Company. When replacing parts, ensure that your service technician uses parts specified by the manufacturer. Do not place anything on the power cord. Place the power cord where it will not be in the way of foot traffic. FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. RFID

(optional) USB Micro SD Card LINE OUT LAN USB COM COM DC-in Jack USB COM COM Cash Drawer HDMI Specification Item C14-1R Display Touch CPU Memory Storage 14.1, Resolution 1366 x 768 PCAP touch Rockchip RK3568 DDR4 4GB Emmc64GB + 1x Micro SD Card Slot External I/O 4 x USB 3.2 + 2 x USB 2.0 Interface 4 x Serial ports, RS232 (RJ45), 0V/5V/12V selected in UI

(COM1, COM2, COM3, COM4) 1 x LAN, (IEEE 802.3 10/100/1000 Mbps Ethernet, RJ45) 1 x RJ11 port supports 2 cash drawers with 24V / 12V by jumper setting 1 x Audio (1 x line out) 1 x HDMI 2.1 1 x DC +24V input 1 x Micro SD card 1 x Speaker 3W 3" Thermal printer Speaker Printer Optional Peripheral MSR (Beep), IC Card Reader, Fingerprint, RFID 2D Bar Code Scanner 5M Camera CD-101C Display Support 2 Independent Displays (Main Display + CD-101C or HDMI) Spill & Dust resistant N/A Operation System Android 12 SW N/A Power Adaptor AC-In 100~240V / DC-Out 24V,72W Reliability System Operating Temperature:0~40C System Humidity: 15% ~ 80%

Storage Temperature: -20~60C Dimensions 340.64 (W) x 315.19 (H) x 247.13 (D) mm Weight 4.0 Kgs

Part name POS Terminal (/) Model /C14-1R

/ / Hazardous substances' name

(Pb)

(Pb)

Lead(Pb) and its compounds

(Hg)

Mercury(Hg) and its compounds

(Cd)

(Cd)

Cadmium(Cd) and its compounds

(Cr6+)

(Cr6+)

Hexavalent chromium

(Cr6+) and its compounds

(PBB)/

(PBB)/

Polybrominated biphenyls

(PBB)

(PBDE)/

Polybrominated diphenyl ethers

(PBDE)

/ /Plastic Shell

/ /Speaker

/ /LCD Panel

/ /Circuit board

//Power Cable

// Other Wire 1. 2. SJ/T 11364 GB/T 26572 GB/T 26572

This table is prepared in accordance with the provisions of SJ/T 11364. Indicates that said hazardous substance contained in all of the homogeneous materials for this part is below the limit

requirement of GB/T 26572. Indicates that said hazardous substance contained in at least one of the homogeneous materials used for this part is above the

limit requirement of GB/T 26572. CE RF Feature RF Spec. NFC

/Contact Information Frequency Range 13.56MHz Max. Output Power (dBm) NA

/Partner Tech Corporation 233110 10F., 233-1, Baoqiao Road, Xindian, New Taipei City 231, Taiwan Phone: +886-2-29188500 http://www.partner.com.tw/

LL ELH T ish tntl bal PARTNER = =O@FECEQRY et oe C Product name (#& i / * & BF ):

is device complies wih part 15 POS Terminal (BF Ri / BF WIM) a pcerce comenes =

Model (B18 / 818); C14-1R qguque ennaaae fublecitoneronoehe tne Rating (OE / BEM): 24.0V=3A a ondons (1) Thi device may MED RARRROAR EA ampmenmas : crete ona 2) this dovices mustaccopt FCC ID:NOPC10-1R URGE Fe WIN SLAIM| any vertronce recolves FM + GRAMME AGA || including interference tha may M2 RAM RAEI EYER = || couse undesired operation MADE IN TAIWAN (#5 38 B28 / & 3344 ik) PARIINER Product name (& #):

POS Terminal (7 Rat) Model (B18): C10-1R Rating (WUE (A): 24.0V=3A RAG: ARARRGARED FCG ID:NDPC10-1R E3FEC EGR UK One Rone BERNE HAPRORRES:

BRUM

+ Ae BA a a CEMA E A SRBERRURED RABR >

This device complies with part 15 of the FCC Rules, Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) This devices. must accept any interference received, including interference that may cause undesired operation, MADE IN TAIWAN (4 38438 )

Agent letter FCC attestation statement Kiwa RF_753, Issue 2 Page 1 of 2 15-02-2023 U.S. Agent Designation for Service of Process

(Applicant and U.S. Agent are Separate Parties) TO:

Kiwa Nederland B.V. Wilmersdorf 50 7327 AC Apeldoorn Postbus 137 7300 AC Apeldoorn Netherlands ATTENTION: FCC Certification Section 2.911(d)(7) Information Designated U.S. Agent Partner Tech USA 0033530866 Company name:

FRN:

Contact person name: Rainy Hsia Street address:

ZIP/City/State Telephone number:

Email address:

Signature:

Date:

1255 N. Patt 92801 949-598-1888 rainy@partnertechcorp.com 03/15/2023 This letter is to confirm that we (the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-

related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Agent letter FCC attestation statement Kiwa RF_753, Issue 2 Page 2 of 2 15-02-2023 Applicant Company name:

Grantee Code:

Contact person name: Ken Wang Street address:

ZIP/City/State Telephone number:

Email address:

Signature:

Date:

Partner Tech Corporation NDP 10FL, 233-1, Baoqiao Road Xindian, New Taipei City, Taiwan

+886 2-2918-8500 ken_w@partner.com.tw 03/15/2023 Revision Record Sheet:

Revision Section Page number Date Remark(s) issued by number 01 02 07-02-2023 1st version RvdM 1 15-05-2023 Added FRN to Agent details RvdM Issued/modified by Function Revision Date

: Richard van der Meer

: Certification assessor

: 02

: 15-02-2023 Verified by Function Date

: Willem Jan Jong

: Team Lead

: __-02-2023 Released by Function Date of release:

: Axel Gase

: Manager Quality Assurance

: __-02-2023

Covered list attestation FCC application letter Kiwa Page 1 of 2 RF_755_02 15-02-2023 P2IPIYV NER CARE . TRUST . RESPONSIBILITY Certification Application Attestation Statements Partner Tech Corporation 10FL, 233-1, Baogiao Road Xindian, New Taipei City Taiwan Subject: FCC ID: NDPC10-1R To Whom It May Concern:

Statement for 47 CFR section 2.911(d)(5)(i)

[Partner Tech Corporation] certifies that as of the date of the application the equipment for which authorization is sought is not covered equipment! prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not covered equipment. Additional Explanation: <N/A>

Statement for 47 CFR section 2.911(d)(5)(ii)

[Partner Tech Corporation] (the applicant) certifies that, as of the date of the filing of this application, he applicant O-is/ &- is not ) identified on the Covered List as an entity producing covered equipment. Date: July 3, 2023 City: Xindian, New Taipei City Name") : Ken Wang Function: Section Manager Telephone number: +886 2-2918-8500 Email address: ken_w@partner.com.tw Signature:

Kany wig

+. The Commission's Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission's website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https:/www.fcc.gov/supplychain/coveredlist .

(2): For FCC it must be the Grantee Code owner or the authorized agent.

(3): double click on the appropriate box and select checked then OK

Declaration for model numbers Hereby, We Name: Partner Tech Corporation Address: 10FL, 233-1, Baoqiao Road, Xindian, New Taipei City, Taiwan declares that this equipment:

Product description: POS Terminal C10-1R, C14-1R, C1XXXXXXXxX (X could be 0-9, -, A-Z or Type designation(s): blank for marketing purpose) Trademark: PARTNER The differences between the models as below. Model No. Remark C10-1R 10.1" Display C14-1R 14"Display C1XXXXXXXX | Marketing purpose

(X could be 0-9, -, A-Z or blank for marketing purpose) The circuit design and layout between of all model numbers are the same. Date: July 3, 2023 City: Xindian, New Taipei City Name: Ken Wang Function: Section Manager Signature: Ka as

RF_160_05 Declaration of Authorisation ki wan Date of issue 02-01-2023 Declaration of Authorization We Name: Partner Tech Corporation Address: 10FL, 233-1, Baogiao Road City: Xindian, New Taipei City Country: Taiwan Declare that:

Name Representative of agent: Nina Hsu ?) Agent Company name: Cerpass Technology Corporation Address: No.10, Lane 2, Lianfu Street, Luzhu District City: Taoyuan City Country Taiwan R.O.C. is authorized to apply for Certification of the following product(s):

Product description: POS Terminal Type designation: C10-1R, C14-1R, C1XXXXXXXxX (X could be 0-9, -, A-Z or blank for marketing purpose) Trademark: PARTNER Validity/ expiry date N/A on our behalf. Date: July 3, 2023 City: Xindian, New Taipei City Name: Ken Wang ?) Function: Section Manager Signature: Ken, Wing boxansseracnas Notes:

(1): Required for FCC application

(2): For FCC it must be the Grantee Code owner or the authorized agent.

@ Cc FCC, Request for non-disclosure ki Wa Date: 02-01-2022 RF_501, Issue 10 Company Name: Partner Tech Corporation Address: 10FL, 233-1, Baogiao Road City: Xindian, New Taipei City Country: Taiwan To: Kiwa Netherlands B.V., Dept. FCC TCB Wilmersdorf 50 7327 AC Apeldoorn The Netherlands Subject: Request for confidentiality FCC ID: NDPC10-1R Reference number: ##HHHHt Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application:

C] Bill(s) of Material XX] Block Diagrams Operational Description [Xx] Schematic Diagrams (J Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission's policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (See notes below):

CJ Internal Photos [-] Users Manual L] Test Set-up Photos (1 External Photos JUSUNGALION:: ...-acsessessnsceransnesnerecitaa nna neMnTAREe Treen eae noNaumEeE euneemeeeneeaua EE Date: July 03, 2023 Name and signature of applicant: Ken Wang key ad Notes:

1) A document or type of document can only have ONE type of confidentiality!

2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)!

The planned date should state in the RF731 application form. 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this!

5) Request for extension or for release must be received by Kiwa NL B.V. at least 7 days before date of actual marketing or before expiration of the STC period