A50 Smart Mini Payment Terminal 1. Contents Checklist Please check the components after unpacking. If any one of them is missing, or if there is a page missing from the product manual, etc., please contact the dealer.\
Name A50 Smart Mini Payment Terminal Mobile Phone Card Pick-up Needle USB Cable Product Manual 2. Production Description Qty. 1 1 1 1 3. Installation SIM/Micro-SD Card Installation 1) Take the Card Pick-up Needle out of the box 2) Insert the Card Pick-up Needle into the SIM/micro-SD card slot 3) Insert SIM /micro-SD card into the pop-up card slot 4. Instruction 1) Power ON/OFF Power on: Connect DC power supply or insert the battery, Press button for 3 seconds until LCD backlight is on. If POS terminal is being turned on successfully, PAX LOGO can be seen and 'Di' from the buzzer can be heard. Power off: Press button for 3 seconds until Shutting down... can be seen. POS terminal is being turned off. 2) IC card Place the chip facing up, insert the IC card into the IC card slot, and push it to the end. 3) Swiping contactless card Place a contactless card close to the sensor area of swiping which is at the back of the terminal. 5. Installation and Usage Tips 1) Avoid exposing the terminal in direct sunlight, or hot / humid / dusty environment. 2) Forbid non-professional to repair the terminal. 3) Before inserting the card, please check the inside and periphery of IC card slot. If you find some suspicious objects, please report to related administrator. Working Environment Temperature: 10~50 (32~122) Storage Environment Temperature: -20~ 70 (-4~158) R.H.:5%~96% (non-condensing) R.H.:5%~95% (non-condensing) 6. Lithium Ion Battery Usage Tips WARNING:
1) Don't use the battery in sunlight or smoky, dusty environment. 2) It's prohibited to strike, squeeze and tread on the battery or throw it into the liquid and fire. 3) If the battery is deformed, damaged or exothermic seriously, please stop using immediately and replace it!
4) If the continuous working time is only half of new one, the battery life may be end. Please replace it!
5) Please use the specified battery model and charger, otherwise it may cause explosion. 6) Charging time can not exceed 24 hours. If the battery is out of power, please recharge in time. Avoid damaging the battery in over-charge and over-discharge. 7) If you don't use it for a long time, please recharge the battery per 6 months to avoid shortening its life. 8) Suggest to replace it when the battery has been used for 2 years. 9) Be sure to follow the instructions to dispose the wasted batteries. 7. Icon shows Do not throw away, need professional recycling. Class II Equipment For indoor use only Energy Efficiency Marking AC voltage DC voltage The MAINS plug is used as the disconnected device. The full text of the EU declaration of conformity is available at the following Internet address:
http://www.pax.com.cn/ProductCE.aspx FCC Regulations:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC RF Exposure Information (SAR) This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States. During SAR testing, this device is set to transmit at its highest certified power level in all tested frequency bands, and placed in positions that simulate RF exposure in usage near the body. Although the SAR is determined at the highest certified power level, the actual SAR level of the while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. The exposure standard for wireless employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: V5PA50 While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement. ISED Notice This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR Innovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en IC: 11689A-A50 ISED Radiation Exposure Statement This EUT is in compliance with SAR for general population/uncontrolled exposure limits in ISED RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and IEC 62209. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. Cet appareil est conforme aux limites d'exposition DAS incontrle pour la population gnrale de la norme CNR-102 science de linnovation et le dveloppement conomique Canada et a t test en conformit avec les mthodes de mesure et procdures spcifies dans IEEE 1528 et IEC 62209. Cet appareil et sa ou ses antennes ne doivent pas tre co-localiss ou fonctionner en conjonction avec tout autre antenne ou transmetteur. PAX TECHNOLOGY LIMITED reserves the right to change product technology specifications without notifying. PAX TECHNOLOGY LIMITED Fax: 0755-86169634 Manufacturer: PAX Computer Technology (Shenzhen) Co.,Ltd. Address:4/F, No.3 Building, Software Park, Second Central Science-Tech Road, High-Tech Industrial Park, Shenzhen, Guangdong, P.R.C. Tel: 0755-86169630 Website: http://www.pax.com.cn Responsible Party: PAX Technology, Inc. 8880 Freedom Crossing Trail, Building 400, 3rd Floor Suite 300, Jacksonville , Florida, 32256 Help-desk 1 877-859-0099