FuzzyScan COMBO Module RM3230 Users Guide Introduction You can connect to other Bluetooth wireless devices by integrating the RM3230 combo module to your device. Specification Brand Name Product Name Model Number WLAN Standard Bluetooth Antenna Port RF Frequency Band Data Modulation Data Rate (Mbps) Channel Number Transfer rates (Max) Antenna terminal Power Type Dimension Operating Temperature Storage Temperature Operating Humidity Range Storage Humidity Range Cino COMBO Module RM3230 IEEE 802 Part 11 b/g/n Bluetooth IM 4.0 + HS compliance Support Single Antenna for both WiFi and BT Country dependant; Typical 2.4 to 2.497 GHz DSSS(DBPSK/DQPSK/ CCK) DFDM(BPSK/QPSK/16QAM/64QAM) DSSS(1/2/5.5/11);
OFDM(6/9/12/18/24/36/48/54) 11b/g/n: 11 Max UART baud rates up to 4Mbits/s 50 Ohms From host 12.5 x 16.6 mm
-20 ~ +70
-40 ~ +85 Less than 85% (non-condensing) Less than 60% (non-condensing) VBAT VBAT GND FM-RX GND FM_RX_ADIO_R FM_RX_ADIO_L GND RF_BG Pin Assignment NO. Pin Name 1 2 3 4 5 6 7 8 9 10 GND 11 BT_HOST_WAKE 12 BT_RST_N 13 BT_WAKE 14 BT_UART_TXD 15 BT_UART_CTS 16 BT_UART_RXD 17 BT_UART_RTS 18 BT_PCM_IN I 19 BT_PCM_CLK 20 BT_PCM_SYNC 21 BT_PCM_OUT 22 VDD_PA3V3 23 WL_TRST_N 24 WL_TDO Type Description I I I I I O O I I/O I O I I O I/O I I/O I I/O I/O O I I I Battery supply input (3.4V~4.5V) Battery supply input (3.4V~4.5V) Ground FM radio RF antenna port Ground FM analog audio output channel 2 FM analog audio output channel 1 Ground Antenna port for WLAN and Bluetooth Ground BT_HOST_WAKE Low asserting reset for BT core BT_WAKE Asserted: Bluetooth device must wake-up or remain awake. Deserted: Bluetooth device may sleep when sleep criteria are met. Bluetooth UART Serial Output. Bluetooth UART Clear to Send. Bluetooth UART Serial Input. Bluetooth UART Request to Send. PCM data input PCM clock, can be master (output) or slave (input) PCM sync signal, can be master
(output) or slave (input) PCM data output VDD power supply (from VBAT) for the internal WLAN power amplifier. Connect as described in the JTAG specification or NC(unconnected) Mixed with UART_TX, Connect as described in the JTAG specification or NC(unconnected) NO. Pin Name 25 WL_SDIO_SPI_HSIC_S EL 26 WL_TDI 27 WL_TCK 28 WL_TMS 29 SDIO_HOST_WAKE 30 BT_REG_ON 31 WL_REG_ON I JTAG_SEL 32 33 VDDIO 34 HSIC_STROBE 35 HSIC_DATA 36 GND 37 LPO_32K 38 GND 39 SD_DAT0 40 SD_CLK 41 SD_DAT1 42 SD_CMD I I/O I/O I/O I/O Type Description I I I I a strapping option to select between SDIO mode (pull low ) or SPI mode(pull high) Mixed with UART_TX, Connect as described in the JTAG specification or NC(unconnected) Connect as described in the JTAG specification or NC(unconnected) Connect as described in the JTAG specification or NC(unconnected) I/O General purpose interface pin. I Used by PMU (OR-gated with WL_REG_ON) to power up or power down internal BCM4330 regulators used by the BT/FM section Used by PMU (OR-gated with BT_REG_ON) to power up or power down internal BCM4330 regulators used by the WLAN section. This pin is also a low-asserting reset for WLAN only JTAG selection pin. Digital I/O supply (1.8V or 2.5V) I I I/O HSIC bidirectional data strobe signal I/O HSIC bidirectional DDR data signal I I Ground Input for external low-power 32.768kHz Clock (Sleep Clock). Ground SDIO data 0. This pin has an internal weak pull-up resistor. SDIO clock. This pin has an internal weak pull-up resistor. SDIO data 1. This pin has an internal weak pull-up resistor. SDIO command. This pin has an internal weak pull-up resistor. NO. Pin Name 43 SD_DAT3 44 SD_DAT2 45 SR_PMU_VSS EXT_PWM_REQ 46 47 VIN_LDO 48 SR_VLX1 49 GND 50 GND 51 GND 52 GND 53 ANT_CTRL_AUX 54 ANT_CTRL_MAIN Type Description I/O I/O I I I O I I I I O O SDIO data 3. This pin has an internal weak pull-up resistor. SDIO data 3. This pin has an internal weak pull-up resistor. Switching regulator ground & PMU block analog ground Auxiliary PMU control inputs. Buck regulator: Battery Voltage Input Core buck regulator: output to inductor and capacitor tank (2.2uH & 4.7uF are required). Ground Ground Ground Ground Antenna Switch control line. Default setting is high. Antenna Switch control line. Default setting is high. The FM mark is used for USI manufacture only. FM FIDUCIAL MARK N/A Module Installation Manual Material:
Description CD_USI PCBA Qty:1 Shielding Case Qty:1 Picture Description Qty:1 Picture Tools:
Description Picture Description Picture Iron Fan Tin wire Description Job Type:
Put CD_USI PCBA on board, solder fixed, avoid short circuits. Note:
Welding CD_USI PCBA temperature of 3500C 100C, not too high or too low. Job Type:
The Shielding Case welded on CD_USI PCBA, careful not to short circuit and CD_USI PCBA. Note:
1 Welded shielding case temperature of 3500C 100C, not too high or too low. 2 Shielding Case not skew or subsidence short circuit. Job Description and Notes:
Step Picture 01 02 Requires a clearance, Avoid short circuit Description 1. Welded shielding case temperature of 3500C 100C, not too high or too low. 2. Welding CD_USI PCBA temperature of 3500C 100C, not too high or too low. 3. Welding CD_USI PCBA requires a clearance and avoid short circuit. 4. Shielding Case not skew or subsidence short circuit. Finished:
Picture Requires a clearance, Avoid short circuit Regulatory Information The Wi-Fi is designed to be interoperable with any Wi-Fi technology product that is incorporating Direct Sequence Spread Spectrum (DSSS) and OFDM data modulation and complies with the IEEE 802.11b/g/n. Safety The Wi-Fi, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by this device, however, is less than the electromagnetic energy emitted by other wireless devices such as mobile phones. The Wi-Fi device operates within the guidelines found in radio frequency safety standards and recommendations. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of a Wi-Fi device may be restricted by the proprietor of the building or responsible representatives of the applicable organization. Examples of such situations include the following:
Using the Wi-Fi equipment onboard airplanes, or Using the Wi-Fi equipment in any other environment where the risk of interference with other devices or services is perceived or identified as being harmful. If uncertain of the policy that applies to the use of wireless devices in a specific organization or environment (an airport, for example), ask for authorization to use the Wi-Fi device before turning it on. This device has been certified to the following radio standards:
FCC Part 15 Subpart C, IC Part 15 Subpart C CE EN300 328, Taiwan LP0002 (NCC) Japan TELEC T401 (MIC) Warning 802.11b/802.11g/802.11n/BT 802.11a
(UNII) 5.25-5.35 (4.7.5)
(4.7.6)
(4.7.7) LP0002 4.3
(1)
(2)
(3)
(4) LP0002 3.4.2 Full Module Approval 314-316MHz433-435MHz 5 5 314-316MHz433-435MHz 55 Case By Case LP0002 4.4 (Citizens Band Radio Service) Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID: SBC-RM3230 ". IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.