FuzzyScan Wi-Fi Module RM3510 Users Guide Introduction You can connect to other Wi-Fi wireless devices by integrating the RM3510 module to your device. 2 Specification Brand Name Product Name Model Number RF Standard RF Frequency Data Modulation Data Rate (Mbps) Cino Wi-Fi Module RM3510 IEEE 802.11b/g Country dependant; Typical 2.4 to 2.5 GHz DSSS(DBPSK/ DQPSK/ CCK) OFDM(BPSK/QPSK/16QAM/64QAM) DSSS(1/2/5.5/11);
OFDM(6/9/12/18/24/36/48/54) Channel Number 11b/g: 11 Channel Band Width (99%) Conducted Output Power Power Type Dimension Operating Temperature Storage Temperature Humidity 11b: 13.88MHz;
11g: 16.52MHz 11b: 8.94 dBm 11g: 10.86 dBm From host 12.5 x 16.6 mm
-10 ~ +50
-40 ~ +70 5 ~ 95% (non-condensing) 3 Pin Assignment No Pin Name Type Description 1 GND GND Ground 2 SD_D1 I/O SDIO 4-bit Mode: Data Line Bit [1] G-SPI Mode: G-SPI Data Output 3 SD_D3 I/O SDIO 4-bit Mode: Data Line Bit [3]
4 RESETn I Reset (Active Low) , leave open if no use. 5 SD_CLK I/O SDIO 4-bit Mode: Clock Input G-SPI Mode: G-SPI Clock Input 6 SD_CMD I/O SDIO 4-bit Mode: Command / Response G-SPI Mode: G-SPI Data Input 7 N/C 8 N/C 9 N/C 10 VDD_33 POWER Connect to 3.3V DC supply 11 N/C 12 SD_D0 I SDIO 4-bit Mode: Data Line Bit [0]
G-SPI Mode: G-SPI Chip Select Input (Active Low) 13 SD_D2 I/O SDIO 4-bit Mode: Data Line Bit [2]
G-SPI Mode: G-SPI Interrupt Output (Active Low) 14 N/C 15 GND GND Ground 16 WL_ACTIVE O WLAN Active (Active Low) 2-Wire BCA Mode When high, WLAN is transmitting or receiving packets. 3-Wire BCA Mode 0 = Bluetooth device is allowed to transmit 1 = Bluetooth device is not allowed to transmit Internal 50kohm pull-down. This pin drives low when PDn is asserted. In WLAN Sleep mode, all I/O Pads are powered down. This Pad must stay at a low state even in power down mode. Please make it open when do not use it. 17 PDn I Pull up by 100kohm, Full Power Down (Active Low) 18 GPIO_0 I/O General I/O Port , leave open if no use. 19 GND GND Ground 4 Regulatory Information The Wi-Fi is designed to be interoperable with any Wi-Fi technology product that is incorporating Direct Sequence Spread Spectrum (DSSS) and OFDM data modulation and complies with the IEEE 802.11b/g. Safety The Wi-Fi, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by this device, however, is less than the electromagnetic energy emitted by other wireless devices such as mobile phones. The Wi-Fi device operates within the guidelines found in radio frequency safety standards and recommendations. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of a Wi-Fi device may be restricted by the proprietor of the building or responsible representatives of the applicable organization. Examples of such situations include the following:
Using the Wi-Fi equipment onboard airplanes, or
Using the Wi-Fi equipment in any other environment where the risk of interference with other devices or services is perceived or identified as being harmful. If uncertain of the policy that applies to the use of wireless devices in a specific organization or environment (an airport, for example), ask for authorization to use the Wi-Fi device before turning it on. This device has been certified to the following radio standards:
FCC Part 15 Subpart C, IC Part 15 Subpart C CE EN300 328, Taiwan LP0002 (NCC) Japan TELEC T401 (MIC) 5 Warning 802.11b/802.11g/BT 6 Federal Communication Commission Interference Statement FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID: SBC-RM3510 ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. 7