Description:
Thank you for purchasing the LTE WIFI wireless data terminal (short for WIFI) The picture is for your reference only, as for the WIFI function and the appearance, please adhere to the actual product instead. The detailed information of the product selection, please inquire the operator. This brochure introduces basic operations of the WIFI. As to the operations of management parameter configuration of the WIFI, please refer to the management procedures or the online help on the web management page. The WIFI can be used in the relatively enclosed space such as the pocket or the bag. However, if the WIFI is in use for an extended period of time, it will become warm because its hard for the WIFI to dissipate the heat in the enclosed space and the current temperature will rise. And at the same time, the WIFI will automatically turn off or cut off the network connection for to protect itself from damage. When this case happened, please put it in the ventilated area to help to dissipate the heat. And then, you can turn it on. Packing information: the head, introduction brochure, certification, data cable and warranty card 1 Getting to know your MIFI 1. Signal indicator 2. WPS indicator 3. Wifi indicator 4. Battery indicator 5. Switch button 6. Battery cover 7. RESET button 8. WPS button 9. Micro USB port 2 3 Getting to know the information of the MIFI indicator I Signal indicator 1. Green indicates 4G signal; 2. Blinking green indicates data transfer 3. Red indicates 3G signal 4. Blinking indicates data transfer II WPS indicator Long press the WPS button for 3 seconds to enable WPS function; WPS indicator blinks after enabling WPS function or indicator keep long light on if WPS client connects success. WPS function will disable if no WPS client connects in 2 minutes. III Message indicator Message indicator always lights on when there is unread message. IV Battery indicator 1. Always Green indicates more than 60% battery power;
2. Blinking Green indicates 20-60% battery power;
3. Blinking Red indicates less than 20% battery power;
4 4. Blinking switch between Green and Red indicates charging. Install the SIM card and battery
*
Steps: Remove the battery cover according to direction of the above blue arrow. Remove battery, Put SIM card to entrance of SIM slot according to the right direction, insert it into slot. Push into the battery from top down, and then install the battery cover according to the right direction. Connect the MIFI with the computer by data cable, and the computer will read the inserted T-Flash card of the MIFI. And it is used as USB stick. USB stick 5 Connecting to the internet by WIFI/WAPI Note: by default, the MIFI management parameters have been preset according to your operators requirements. You can go quickly into the internet by the following steps. As to how to configure management parameter, please refer to the management procedures or the online help on the web management page. Step1: turning on the MIFI Step2: establishing WIFI connection or wired connection Step3: connecting to the internet Press and hold the power button until the screen is bright, indicating that the WIFI is turned on; and then press and hold it again until the screen is dark, indicating that the WIFI is turned off.(Note: when the WIFI is turned on, the power button also can be used as page turning button. If it displays the first page, press power button, then it will show the second page; and at this moment, press power button again, it will appear the first page.) II. Establishing WIFI connection or wired connection I. Turning on the WIFI 6 1. Establishing WIFI connection. (Take the computer for example) Guarantee MIFI power on, indicator is light on. Click StartControl panel Network connectionWireless network connection. (Note: before Establishing WIFI connection, please ensure that the computer is equipped with a WLAN card. If the computer indicates a wireless network connection, and the WLAN card can be used. Otherwise, you need to verify that your WLAN card is working properly. ) Click and check the available wireless network, and it will display a list of wireless network connections. Select the wireless network connection with the WIFIs SSID, and click. If the wireless network connection is encrypted, you need to enter the correct network encryption key (the password). To view the current SSID and the network encryption key, please see the words printed on the 7 Label of the MIFI. (Or see the content of the second page on the screen). W ait a moment for the wireless network connection icon to appear in the system tray in the lower right corner of the computer screen. And the wireless network is then established. 2. Establishing wired connection After turning on the MIFI, you can connect it with the computer by data cable. when the computer pops up finding new hardware, and on the menu Can Windows be linked with Windows Update to search for the software? , select No, temporarily not (T) , then click next step (N)> ;
After select automatically install software (recommended) (I), click next step(N)>;
When it appears unable to install this software, and click finish;
8 Repeat the above steps. These are the drivers for other uses unrelated to wire connection;
Until Mobile RNDIS Network Adapter appears, select automatically install software (recommended)(I). And then click next step (N)>, and click finish. When the driver has been installed automatically, Establish wired connection finishes. Connecting the MIFI and the computer by data cable, and the computer can be connected to the internet by the wired network. III. Connecting to the internet When the WIFI is connected with client, it will get into the internet automatically. (If your SIM card is short o f cash, it will not be connected.) Logging into the Web Management Page 1. Make sure the connection between the MIFI and the computer is working normally. 2. Open the browser, and enter http://192.168.0.1 3. Enter the password, and click login. The administrator has the right to check and modify configuration permission. The default user name is admin, and the default password is admin. Note: If you cant go into the web management page while the MIFI is linking with the computer by data cable, in the address box. 9 The first method: charging by power adapter Daily use you can start the management procedures and then could open web management page, and it will be available Charging the battery Note: If the battery hasnt been used for a long time, please charge it for a while before using. Note:
1. You should use the power adapter compatible with the WIFI (5v, 100mA) provided by the designated manufacture. If you use any incompatible one which is provided by other producer or agent, it may cause the WIFI to malfunction or even cause danger. And it also violates the warranty terms of the MIFI and some regulations about communication terminal products set by the government. 10 2. The power adapter is an optional accessory. If it is not included in the package, please contact with the producer to buy a compatible one that is in good quality. Please use the data cable provided with your device to connect the WIFI to the computer. Sleeping mode If you dont do any operations to MIFI for a period of time, the screen will be dark. And in default, the MIFI will go into sleeping mode if there isnt any information transmitted within 10 minutes. The second method: Charging by connecting with the computer 11 Verifying the PIN code If the Verifying function is available, please log into the web management page and click dial up.And according to the tip, enter the right PIN code in the corresponding position. PIN/PUK code and SIM card all together are provided by the operator. Please inquire the operator for the detailed information. As to how to log into the web management page, please refer to logging web management page. Connecting with multi-devices WiFi devices or computers can get into the internet by the MIFI. The steps for connecting are depended on WiFi devices or the operating system of the computer. Please operate according to the detailed tips. Restoring to factory settings If you forget some configuration parameters, you can restore to factory settings and then configure them again. You can log into WEB UI to restore to factory settings. Or you can straighten clip, and insert it into Reset button, then press it for 5 seconds, and the MIFI will restart again and restore to factory settings. Note: After these operations, all the configured parameters in the MIFI personal center will be deleted. All configurations of the web management page will be restored to factory settings. 12 Tips:
If your MIFI cannot work normally, here are some tips and you can have a try:
1. Check the management procedures or the online help on the web management page. 2. Reset the MIFI 3. Restore to factory settings 4. If all the connection and the working state are all in good condition, but your SIM card is short of cash, you are still unable to surf in the internet. 5. Consult the operator Notes: The pictures are for reference only; please adhere to the actual product. FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference. 13
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. 14 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. SAR Information Statement Your wireless data terminal is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. * Tests for SAR are conducted with the phone transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because 15 the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. Before a phone model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this model phone when worn on the body, as described in this user guide, is 0.538W/Kg(Body-worn measurements differ among phone models, depending upon available accessories and FCC requirements). The maximum scaled SAR in hotspot mode is 0.666W/Kg. While there may be differences between the SAR levels of various phones and at various positions, they all meet the government requirement for safe exposure. The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RFexposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/ oet/fccid after searching on FCC ID: 2ALJJJ500 Additional information on Specific Absorption Rates (SAR) can be found on the Cellular 16 Telecommunications Industry Asso-ciation (CTIA) web-site at http://www.wow-com.com. * In the United States and Canada, the SAR limit for mobile phones used by the public is 1.6 watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a sub-stantial margin of safety to give additional protection for the public and to account for any variations in measurements. Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 10mm must be maintained between the users body and the handset, including the antenna. Third-party belt-
clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. 17