Manual for Electronic Labels and Radio Modules Read all documents and system instructions carefully to minimize the risk of injuring persons and to avoid damage to the system or damage to the environment. Always keep all documents and guidance accessible. If necessary, the content of this document will be updated. You can request the latest version of the document via service@pdi-digital.com. Register at the https://www.pdi-digital.com to get access to the latest software and documentation. An electronic label is a device that shows digital information on its display. In comparison to printed paper the information is automatically updated if object data changes. The PDi Digital electronic label family offers high-quality display options, operating with a replaceable battery, thus working without any external power supply. The PDi Digital (2.4GHz) electronic label family can change all pixels to black, white or red/yellow. The current line-up has display sizes from 1.6 inch to 12.2 inch. They may be used in landscape and portrait mode and can be configured in terms of radio, theft protection, display protection and LED flash. Next to the PDi Digital electronic label family, a radio module is available in order to give third parties access to the existing SES Imagotag + PDi Digital 2.4GHz infrastructure. The module is acting similar to an electronic label but has no display. General Key Features:
11 available communication channels 2.4 GHz proprietary radio protocol BLE Beaconing for locationing purposes Radio coverage: up to 25 meters Bi-directional communication Ultra-low power consumption Customer-replaceable battery Full graphical e-Ink display with paper-like readability e-ink displays are available (Black/White, Black/White/Red, Black/White/Yellow) Different configurations available (theft protection, display protection, LED flash) Label versions for deep-freezing environments Super wide viewing angle (nearly 180 degrees) Flexible mounting options available May be used in landscape and portrait mode Fast response time Multiple pages support with preloading and fast page switching 128-bit AES encryption with secure key exchange Integrated Passive NFC tag The installation instructions are intended for trained electricians who can exhibit the following qualifications:
Knowledge of the use of tools and work instructions. Knowledge of the usable conditions of the tool. Knowledge of the electrical safety instructions. Knowledge of the electrical building regulations. Knowledge of the relevant standards. Knowledge of the assembly schedule. The power supply are cell-button batteries. The following table will give you a short overview about all kinds of labels and their batteries. Caption Model Display Resoluti on Active Display Area
(mm) Displa y colors Usabl e pages Battery Type Nominal capacity Operat ing Voltag e Wak eup
(sec onds
) Battery lifetime 5 years with N updates per day ED03-0260-A sepioo D2.6 ED03-0260-A/B Bossard SmartLabel 2.6 sepioo D2.7 ED03-0270-A/B Wrth iDisplay 2.7 RECA iDisplay 2.7 sepioo D4.2 B sepioo S1 ED03-0420-A ED03-0270-A ED03-0270-A RMG3-RCOM-
A/B 296x152 296x152 60.1 x 30.7 60.1 x 30.7 b/w/r b/w/r 264x176 264x176 57.3 x 38.2 57.3 x 38.2 b/w b/w 264x176 57.3 x 38.2 b/w 400x300 84.8 x 63.6 b/w
12 12 12 12 12 12
2xCR2450 3V 2xCR2450 3V 1100 mAh 1100 mAh 15 15 2xCR2450 3V 2xCR2450 3V 1100 mAh 1100 mAh 15 15 2xCR2450 3V 1100 mAh 15 3xCR2450 3V 1650 mAh 15 2 2 2 2 2 2 external supply 3V external supply 15 external supply Note: battery lifetime can vary depending on the operating conditions of the labels (temperature, radio usage etc). General remarks The sepioo labels must be installed according to the mounting instructions of the producer. In rare cases it may occur that the usage of wireless appliances is restricted by the building owner
(e.g. Airport or Hospital). Please contact the appropriate authorities before installing the PDi Digital sepioo labels. Environmental General E-Paper displays are moisture and UV sensitive. The absolute rating operating environments describes the boundary conditions for updating the display while the absolute rating storage environment (see Storage and warehousing) describes the boundary conditions for a display not updating. Operating temperature Operating temperature for maximum lifetime Operating humidity BW 0 C to +45 C BW (Wide temp/Freezer)
-25 C to +30 C BWR 10 C to +40 C 21 C 21 C 21 C 30% - 80%
30% - 80%
35% - 70%
Cleaning Instructions Clean the electronic label with the help of a damp cloth. Use only common household cleaners. Do not clean the label with alcohol, solvents and / or abrasive cleaning products. Note: Do not use liquid or aerosol cleaners and keep it away from water. Temperature and Humidity Conditions High humidity combined with low temperature are not recommended. Low temperature will reduce the battery lifetime. Storage and warehousing While displays are rated to perform according to specification for the warranty period at the absolute specified operating environment, the better the storage condition, the better the E-Paper displays will perform. Like other moisture and UV sensitive components, we recommend that our labels are stored in temperature and humidity-controlled environments, and whenever possible, under below defined Optimal Storage Conditions, away from sunlight, to optimize their performance. It is strongly recommended to observe the following points to ensure the best operation, functioning and battery lifetime:
Storage temperature and humidity Storage temperature Storage humidity Optimal storage temperature Optimal storage humidity
(non-condensing) BW BW (Wide temp/Freezer) BWR
-20 C to +50 C 30% - 80%
-20 C to +50 C 30% - 80%
-20 C to +50 C 40% - 70%
0 C to +30 C 0 C to +30 C 0 C to +30 C 40% - 60%
40% - 60%
40% - 60%
Do not operate any ESL Infrastructure (e.g. SES-imagotag AP-2010 or MAP 2014T/Lancom L-151E, ... ) in warehouse storing labels or where the radio coverage will activate stored labels. o The label will permanently try to connect to the access point, leading to less usable battery lifetime. The maximum storage time of labels should not exceed 0.5-1 year If these listed limits are not complied, the specified battery lifetime can vary, and display quality can be influenced negatively. Intended Use PDi Digitals electronic label family is exclusively designed to connect to Access Points of the company SES-imagotag or acknowledged partners via radio. The device may only be used in areas where the environmental fulfill the requirements described in the chapter Environmental. Improper use PDi Digital is not responsible and does not assume liability for damage or injury to persons, property, environment and the PDi Digital electronic label family itself caused by improper installation or improper handling. The operator assumes liability for any damage that results from improper use. The following usage is not allowed:
Don't drop electronic labels. Keep electronic labels away from water except they are meant to be waterproof. Dont use electronic labels with defective parts. Dont use electronic labels with spare parts and accessories which are not examined and approved by PDi Digital. Unauthorized changes or modifications to electronic labels and their components without the consent of PDi Digital are strictly forbidden. PDi Digitals electronic labels do not contain parts, except batteries, that are allowed to be maintained by the user. PDi Digitals electronic labels must NOT be dismantled. For necessary maintenance or repair works always contact the manufacturer. Don't throw electronic labels into the dustbin. Deposit electronic labels at a reprocessing company. Contact PDi Digital for more details about the removal process. Please do not use any liquid or spray cleaners directly on the surface of the electronic labels. PDi Digital takes no responsibility for stolen electronic labels without encryption. KEEP BATTERIES OUT OF REACH OF CHILDREN Swallowing batteries may lead to serious injury in as little as 2 hours or death, due to chemical burns and potential perforation of the esophagus. If you suspect your child has swallowed or inserted a button battery immediately call local Poisons Information Authority, with contact information available online. Don't heat, recharge or bend the battery. Examine devices and make sure the battery compartment is correctly secured, e.g. that the screw or other mechanical fastener is tightened. Do not use if the compartment is not secure. Dispose used button batteries immediately and safely. Empty batteries can still cause harm. Tell others about the risk associated with button batteries and how to keep their children safe. Certificates Hereby, PDi Digital GmbH declares that the radio equipment sepioo D2.6, sepioo D2.7 and sepioo S1 is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address:
https://www.pdi-digital.com.com/sepioo-declaration-of-conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION TO USERS Changes or modifications not expressly approved by the party responsible for compliance could void the user`s authority to operate the equipment. FCC rules apply to the following products: sepioo D2.6, Bossard SmartLabel 2.6, Wrth iDisplay 2.7, RECA iDisplay 2.7, sepioo D2.7 and sepioo S1 This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lemetteur/recepteur exempt de licence contenu dans le present appareil estconforme aux CNR dInnovation, Sciences et Developpement economique Canadaapplicables aux appareils radio exempts de licence. Lexploitation est autoriseeaux deux conditions suivantes:
1) Lappareil ne doit pas produire de brouillage;
2) Lappareil doit accepter tout brouillage radioelectrique subi, meme si lebrouillage est susceptible den compromettre le fonctionnement. IC standards apply to the following products: sepioo D2.6, sepioo D2.7 and sepioo S1 NCC rules apply to the following products: sepioo D2.6, sepioo D2.7 and sepioo S1