FCC ID: I4S-SOLO Powered Speaker

Solo Portable PA Manual 1 www.peavey.com FCC/ICES Compliancy Statement This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS Standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, that may cause undesired operation. Le prsent appareil est conforme aux CNR dlndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes: (1) Iappareil ne doit pas produire de brouillage, et (2) Iutilisateur de Iappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Warning: Changes or modifications to the equipment not approved by Peavey Electronics Corp. can void the users authority to use the equipment. Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures. Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is con-

Increase the separation between the equipment and receiver. nected. Consult the dealer or an experienced radio/TV technician for help. Caution The equipment complies with FCC radiation exposure limits set forth for an uncontrolled envi-

ronment. Features and specifications are subject to change without notice. Peavey Electronics Corporation 711 A Street Meridian, MS 39301

(601) 483-5365 FAX (601) 486-1278 www.peavey.com 2015 EX000030 2 This equipment complied with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. FCC Radiation Exposure Statement IC Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. The an-

tenna should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet appareil est conforme aux limites d'exposition aux rayonnements de la IC pour un environnement non contrl. L'antenne doit tre install de faon garder une distance minimale de 20 centimtres entre la source de rayonnements et votre corps. L'metteur ne doit pas tre colocalis ni fonctionner conjointement avec autre antenne ou autre metteur. 3 Solo Portable Powered Speaker Systems Congratulations on purchasing the Peavey Solo Battery-Powered Speaker System. This compact, portable and powerful system is a perfect solution for the weekend warrior, songwriter round or a small family gathering. With a simple and intuitive layout, the Solo is a great plug and play option. Bluetooth stereo linking Bluetooth audio input for streaming music from any Bluetooth device 4 Channel mixer 2 XLR mic inputs and 2 1/4" Line Inputs Rechargeable lithium ion battery Peavey MidMorph and Kosmos C controls Guitar input 90 Watts 6.5 (165mm) Woofer 2.5 (63.5mm) x 3 tweeter array Description:

Peavey Solo Weighing in at only 15 lbs., the lithium ion batery-powered Peavey Solo is the perfect solution for a wide variety of portable applications, whether you want professional grade sound for streaming from any Bluetooth Audio device at the beach, park, or party, or you are looking for a small PA for announcements, portable tour groups, or playing your guitar, keyboard or other instrument remotely. With more than 55 years of audio excellence and many patents to prove it, the Peavey Solo uses exclusive features that truly set us apart from the competition. Our exclusive Guitar Input selection changes the input type and EQ on the guitar channel to optimize it for the instrument. Our Mid-Morph EQ makes dialing in the perfect sound for a microphone simple; as you turn it, it automatically helps you select the best mix. You'll never hear anything like the clarity that comes from Peavey Kosmos. This feature will brighten dead guitar strings or enhance the clarity of just about anything you plug in. Our channel priority feature allows announcements to automatically take priority over music channels and lowers the volume of the music long enough to talk over it, perfect for mobile DJs or events. Sonically superior to our competition and featuring a wide coverage patern, the Peavey Solo is perfect for making music all day or night, anywhere you need it. Everything you need and nothing you don't from the audio experts at Peavey. Installation Note:

This unit must have the following clearances from any combustible surface: top: 8", sides: 12", back: 12"

4 Top Panel 9 12 11 5 4 2 3 1 15 14 13 5 10 8 7 6 4 3 Input Panel 1. MIC/LINE INPUT (CH.1-2) This combination input jack can accept either a (balanced or unbalanced) input or a XLR balanced, low-impedance connection. The tip is positive on the balanced connector and pin 2 is positive on the XLR input. 2. Level Control The level control allows the user to adjust the amount of signal from each channel in the mix. Typical operation is between 3 and 8 (dependent upon the input devices) but should be lower than the master level. Please remember that this acts like a preamp, so if you are using a device that has a volume output control (i.e. a tape or CD player) you will need to match the levels by adjusting the level controls on each unit. 3. Priority When this button is pressed, speaking into the mic in the corresponding channel will lower the BT signal approximately 20dB. This will allow important announcements to be heard over Bluetooth background music in the speaker. 4. Mid-Morph EQ (CH.1-2) Where most mid-range controls work at just one frequency, the patented Peavey Mid-Morph works at two. When turned counterclockwise, it cuts the 250Hz to reduce frequencies that muddy the sound. When turned clockwise, it boosts at 4kHz to add intelligibility to vocals. Either way, improved vocal or instrument definition can be achieved. 5. Reverb Control This is used as a send control to the effects bus. It controls the amount of reverberation that is added to the output signal. 6. Line Input (CH.3-4) This balanced input allows for line level signals to be added to the SOLO. The tip is positive. When the GTR (7) button is pressed, the input changes to a high impedance (1Meg ohm), like a 12AX7 vacuum tube guitar amplifier input. 7. GTR Engaging this button optimizes the on-board equalization for electric guitar. 8. EQ (CH.3-4) This active EQ control shapes the sound of the signal in channels 3 and 4. Turning the control clockwise boosts the bass and treble signals simultaneously. Turning the control counter-clockwise, reduces the bass and treble signals. 9. Kosmos This control is a very selective high frequency filter with a high Q. The effect varies with source material, so some experimentation is required for optimum results. But it can normally be used to add some clarity to the high frequency range. 10. Master Level This control sets the output level of the speaker. 6 11. Bluetooth Pair Button and LED To pair with a Bluetooth device, press the Pair button. The blue pair LED will begin to blink and the SOLO can now be discovered by your Bluetooth device. Once the SOLO is discovered, you can connect to it by selecting it on your device. Once they are paired, the blue LED will quit blinking and illuminate continuously. 12. Bluetooth Link To link the SOLO to a second SOLO, press the Link button on the first unit your BT device is paired with. The blue pair LED will begin to blink. With the second SOLO powered up, press the BT button to activate the BT mode. Then press the pair button, the two units will now connect to each other. Once they are paired, the Link LEDs will stop blinking and illuminate continuously. 13. AC Power Inlet This is the receptacle for an IEC line cord, which provides AC power to the unit. Connect the line cord to this connector to provide power to the unit. Damage to the equipment may result if improper line voltage is used. Never break off the ground pin on any equipment. It is provided for your safety. If the outlet used does not have a ground pin, a suitable grounding adapter should be used and the third wire should be grounded properly. To prevent the risk of shock or fire hazard, always make sure that the amplifier and all associated equipment it properly grounded. 14. Power Switch This is the main power switch. 15. Battery Charge Level LEDs The battery charge level LEDs show the charge status of the battery. When the unit is turned off and AC power is applied to the AC inlet (13), the red charge LED will illuminate continuously. When the power switch (14) is put in the on position, the LED array will display the battery charge status, 25%, 50%, 75%

or 100%. 7 Specifications Connections Frequency Response Peak Power Max Output SPL 2 - XLR input jacks (Ch 1&2) 4 - 1/4 (6.35mm) TRS input jacks (Ch 1-4) 74 - 20kHz 90 Watts (60W LF/30W HF) 115dB SPL peak (1W/1M) SOLO speaker v5 A2DP streaming, stereo linking with a second 6.5 (165mm) Woofer 2.5 (63.5mm) x 3 tweeter array 15.4lbs (7kgs) 11.25" x 10" x 14.5" (28.58mm x 25.40mm x 36.83mm) Bluetooth Woofer Tweeter Weight Dimensions (length x width x height) 8 www.peavey.com Warranty registration and information for U.S. customers available online at www.peavey.com/warranty or use the QR tag below Peavey Electronics Corporation 5022 Hartley Peavey Drive Meridian, MS 39305 (601) 483-5365 FAX (601) 486-1278 Features and specications subject to change without notice. Logo referenced in Directive 2002/96/EC Annex IV

(OJ(L)37/38,13.02.03 and defined in EN 50419: 2005 The bar is the symbol for marking of new waste and is applied only to equipment manufactured after 13 August 2005 9

cit Priority (_) SOLO Battery Powered PA le) SOLO Battery Powered PA

--Apparatets stikprop skal tilsluttes en stikkontakt med jord, som giver forbindelse til stikproppens jord. (For Denmark Only)

. | SCaite on titettava suojamaadoituskosketiimilla varustettuun pistorasiaan. (For Finland Only)

--Apparatet ma tilkoples jordet stikkontakt. (For Norway Only)

] Apparaten skall anslutas till jordat uttag. (For Sweden Only) THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.

| OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE. THAT MAY CAUSE UNDESIRED OPERATION. CAN-ICES-3(B)/NMB-3(B) O CALIFORNIA PROPOSITION 65 WARNIN:

Cancer and Reproductive Harm www. P65Warnings.ca.gov Peavey Electronics Corp. 5032 Hartley fgave Prive eridian, M 5) (601) 483-5365 (O) YY 4) www.peavey.com Made in China Peaveye tronics Con SOLO FCC ID: 14S-SOLO IC: 3642A-SOLO

Agent Authorization Letter 03/25/2024 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern:

We, the undersigned, hereby authorize Eurofins Electrical Testing Service (Shanghai) Co. Ltd. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Printed: Mark Wu Title: Project Manager Company name: Peavey Electronics Corp.

03/25/2024 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for FCC ID: I4S-SOLO Peavey Electronics Corporation (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely,

(Applicant signature)

(Applicant printed name) Mark Wu 03/25/2024 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for FCC ID: I4S-SOLO Peavey Electronics Corporation (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely,

(Applicant signature)

(Applicant printed name) Mark WU

Long Term Confidentiality Request Letter 03/25/2024 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR Product typePowered Speaker Model name: SOLO FCC ID: I4S-SOLO To Whom It May Concern:

This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the

-Block Diagram

-Schematics

-Circuit Description required to be submitted with this application be permanently withheld from public review. The above documents are company proprietary information that could never get into the possession of your competition. Please contact me if there is any information you may need. Sincerely, Printed: Mark Wu Title: Product Compliance Manager Company name: Peavey Electronics Corporation

Attestation Statements 03/25/2024 TO: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046, USA RE: Attestation Statements Part 2.911(d)(7) request for FCC ID: I4S-SOLO Peavey Electronics Corporation, the undersigned, hereby authorize ourselves to act as our designated U.S. agent for service of process. Peavey Electronics Corporation accepts the responsibility to act as designated U.S. agent for service of process. Applicant information:

Company Name: Peavey Electronics Corporation Address: 5022 Hartley Peavey Drive P.O. Box 2898 Meridian MISSISSIPPI 39305 USA FRN: 0001739556 Contact Name: Mark Wu Telephone No: +86-0755-26801582 Email: Mark.Wu@peavey.com Signature

[Mark Wu]

U.S. Agent Information:

Company Name: Peavey Electronics Corporation Address: 5022 Hartley Peavey Drive P.O. Box 2898 Meridian MISSISSIPPI 39305 USA FRN: 0001739556 Contact Name: Mark Wu Telephone No: +86-0755-26801582 Email: Mark.Wu@peavey.com Signature

[Mark Wu]