FCC ID: QWY-V1233-0 GSM/WCDMA/LTE Telematics ROW Module

Peiker product IDs:

Revision:

Date:

V123x-0 (LTE-NAD-A) User manual 2189-230-042-00 (V1230-0) 2189-231-042-00 (V1231-0) 2189-232-042-00 (V1232-0) 2189-233-042-00 (V1233-0) 1.4 August 2017 _______________________________________________________________________________________________________________ Seite 1 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Revision History Date 28.02.2017 1.0 01.03.2017 1.1 06.03.2017 1.2 mgi phse mgi 08.08.2017 1.3 04.09.2017 1.4 phse phse Revision Name Comment Initial document based on V123x-1 documents Some rewording as well as some corrections Model name changed to V123x-0 Renumbering of some sections Added new section called Maximum TX Output Power Updated the temp range table from section 2.12.1 Reworked section 6 Updated the pin-out table _______________________________________________________________________________________________________________ Seite 2 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Content 1 2 Introduction .......................................................................................................................................... 4 1.1 Scope .................................................................................................................................................. 4 1.2 Audience ............................................................................................................................................ 4 1.3 Contact information, Support ......................................................................................................... 4 Product Overview ................................................................................................................................ 5 2.1 Product Variants ................................................................................................................................ 5 2.2 Supported Technology/Frequency Bands ..................................................................................... 5 2.3 Maximum TX Output Power ............................................................................................................ 5 2.5 Features ............................................................................................................................................. 6 2.6 Certifications / Approvals................................................................................................................. 7 2.8 Connectors ......................................................................................................................................... 7 2.8.1 Module Signal and RF Connectors .......................................................................................... 7 2.8.2 Ground and Heat Dissipation Connectors .............................................................................. 7 2.9 Main Interfaces ................................................................................................................................. 8 2.9.1 USB .............................................................................................................................................. 8 2.9.2 SIM Interface ............................................................................................................................. 8 2.9.3 Power on ..................................................................................................................................... 8 2.9.4 Reset ........................................................................................................................................... 8 2.9.5 GPIOs .......................................................................................................................................... 9 2.9.6 GSBIs ........................................................................................................................................... 9 2.9.7 Module Pin-out ......................................................................................................................... 10 2.10 Supply Voltage .............................................................................................................................. 15 2.11 Power Consumption ..................................................................................................................... 15 2.12 Environmental Specification ........................................................................................................ 16 2.12.1 Temperature Range .............................................................................................................. 16 Evaluation Kit ..................................................................................................................................... 17 3 AT Command interface ..................................................................................................................... 20 4 5 Safety Recommendations according to EN60950-1 ..................................................................... 22 6 RED/FCC/IC Regulatory Notices ...................................................................................................... 23 6.1 Modifications .............................................................................................................................. 23 Interference ................................................................................................................................ 23 6.2 6.3 FCC Class B Digital Device ....................................................................................................... 23 6.3 OEM Responsibilities ................................................................................................................. 24 List of Acronyms ................................................................................................................................ 25 7 _______________________________________________________________________________________________________________ Seite 3 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 1 Introduction 1.1 Scope This document gives an overview about electrical, mechanical and functional details of the peiker LTE-

NAD-A V123x-0 modules. 1.2 Audience Information to integrate the module in some other applications. 1.3 Contact information, Support peiker acustic GmbH & Co KG Max-Planck Street 32 D-61381 Friedrichsdorf / Ts. Germany http://www.peiker.de info@peiker.de _______________________________________________________________________________________________________________ Seite 4 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 2 Product Overview 2.1 Product Variants The LTE-NAD-A module family consists of four regional variants:

Peiker product #

2189-230-042-00 (V1230-0) 2189-231-042-00 (V1231-0) 2189-232-042-00 (V1232-0) 2189-233-042-00 (V1233-0) Module configuration ECE configuration NA configuration CHN configuration RoW configuration 2.2 Supported Technology/Frequency Bands V1230-0 GSM Bands WCDMA Bands LTE Bands 900MHz and 1800MHz FDD1, FDD3 and FDD8 eFDD1, eFDD3, eFDD7, eFDD20, eFDD28A, eFDD32 and eTTD38 V1231-0 GSM Bands WCDMA Bands LTE Bands 850MHz and 1900MHz FDD2, FDD4 and FDD5 eFDD2, eFDD4, eFDD5, eFDD7, eFDD12 and eFDD29 V1232-0 GSM Bands WCDMA Bands LTE Bands V1233-0 GSM Bands WCDMA Bands LTE Bands 900MHz and 1800MHz FDD1 and FDD8 eFDD1, eFDD3, eFDD7, eTTD38, eTTD40 and eTTD41 850MHz, 900MHz, 1800MHz and 1900MHz FDD1, FDD2, FDD3, FDD5, FDD6, FDD8 and FDD19 eFDD1, eFDD3, eFDD5, eFDD7, eFDD8, eFDD9, eFDD19, eFDD21, eFDD28B and eTTD40 2.3 Maximum TX Output Power GSM 850 and GSM 900 (PCL=5, 1 UL TS): 34,5 dBm GSM 1800 and GSM 1900 (PCL=5, 1 UL TS): 31,5 dBm GPRS 850 and GPRS 900 (PCL=5, 4 UL TS): 29 dBm GPRS 1800 and GPRS 1900 (PCL=0, 4 UL TS): 26 dBm EDGE 850 and EDGE 900 (PCL=8, 4 UL TS): 23 dBm _______________________________________________________________________________________________________________ Seite 5 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe EDGE 1800 and EDGE 1900 (PCL=2, 4 UL TS): 22 dBm WCDMA (all supported frequency bands): 25 dBm LTE (all supported frequency bands): 25 dBm 2.4 Module to Hosts Mapping The below table shows the mapping between the module variants and the host/ATM-02 devices:

Module Host devices embedding this module variant V1230-0 ATM-02-ECE-R1 and ATM-02-ECE-T1 V1231-0 ATM-02-US-R1 and ATM-02-US-T1 V1232-0 ATM-02-CHN-R1 and ATM-02-CHN-T1 V1233-0 ATM-02-ROW-R1 and ATM-02-ROW-T1 2.5 Features Features IMS/VoLTE

- Same footprint and pin-out (all modules)

- Voice and data calls (all modules)

-

- 4G: Rel-11, 3G/3G+: Rel-9, 2G: Rel-9

- DTM/eDTM (all modules)

- Standalone GPS, GLONASS, Galileo, SBAS, QZSS and BeiDou Data rates

- GPRS/EDGE: Multislot class 33

- WCDMA: DL /UL up to 384kbps HSPA+:

Category 24 in DL using 64 QAM and Dual-Cell; Up to 42 Mbps (All modules except V1231-0) Category 14 in DL using 64 QAM; Up to 21 Mbps (V1231-0) Category 6 in UL using 16 QAM; Up to 5.76 Mbps (All modules)

- LTE Category 11: Up to 450 Mbps in DL using 3 CCs, up to 75 Mbps in UL (All modules) Power Classes

- LTE: All supported bands, Power Class 3

- WCDMA: All supported bands, Power Class 3

- EDGE: 850/900/1800/1900, Power Class E2

- GSM/GPRS: 850/900, Power Class 4

- GSM/GPRS: 1800/1900, Power Class 1 Dimension and Weight

- Dimensions: 35mm x 38mm x 4,35mm

- Weight < 10 grams _______________________________________________________________________________________________________________ Seite 6 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 2.6 Certifications / Approvals RED GCF Planned Planned Planned Planned V1230-0 V1231-0 V1232-0 V1233-0 2.7 HW Features PTCRB FCC/IC AT&T Planned Planned Planned Planned

- Qualcomm X12 LTE, 20nmSoC

- MDM9240 Baseband / PMIC: PMD9645 / WTR3925 WTR4905

- Cortex-A7 up to 1.2 GHz

- Modem and low power audio sub systems: QDSP6 processor at up to 850 MHz (turbo)

- RPM Resource and power manager: Cortex M3 up to 100 MHz

- 4Gb NAND Flash

- 2Gb LPDDR2 SDRAM

- 19.2MHz clock reference

- GPS, GLONASS, BeiDou, and Galileo 2.8 Connectors 2.8.1 Module Signal and RF Connectors LTE-NAD-A has 172 signal pins (2xAA and 2xBB) connector pads with 1.0mm pitch. The signal pads are located close to the board edges. There are three antenna pads, each collocated by RF GND connectors

- Main transmit and receive antenna pin LGA_PRX_ANT

- Diversity antenna for WCDMA respective MIMO antenna for LTE pin LGA_DRX_ANT_IN

- GNSS antenna for both GPS and GLONASS pin LGA_GPS_DRX_ANT 2.8.2 Ground and Heat Dissipation Connectors To support the usage of module under complicated thermal conditions, there are a number of large grounded pads in the center of PCB. These pads are dedicated ground pads to transfer heat dissipation to a carrier board. This should be especially considered by customer designs. A reference design showing landing patterns and PCB stack-up is available on request. _______________________________________________________________________________________________________________ Seite 7 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 2.9 Main Interfaces 2.9.1 USB LTE-NAD-A has one USB2.0 OTG high speed (480MBit) compliant interface including the PHY. This IF consists of four signals:

- USB_HS_DP:

- USB_HS_DM

- USB_HS_ID:

- MDM_VBUS_DET:

USB Data Plus signal USB Data Minus signal USB high-speed data - ID USB Voltage Supply LTE-NAD-A has one USB3.0 high speed (480MBit) compliant interface including the PHY. This IF consists of four signals:

- MDM_USB_SS_RX_P:

- MDM_USB_SS_RX_M

- MDM_USB_SS_TX_P:

- MDM_USB_SS_TX_M:

A dynamic reconfiguration between USB-Host or USB-Device is not foreseen. LTE-NAD-A can be configured to USB-Host or USB-Device by insertion of a resistor on the USB_ID line. USB 3.0 receive plus USB 3.0 receive minus USB 3.0 transmit plus USB 3.0 transmit minus 2.9.2 SIM Interface LTE-NAD-A has two SIM interfaces that are compatible for both 1.8V and 3V SIM Cards. Those IFs consist of the following signals:

VREF_UIM1 / VREF_UIM2 UIM1_CLK / UIM2_CLK UIM1_DETECT / UIM2_DETECT UIM1_DATA / UIM2_DATA UIM1_RESET / UIM2_RESET The data rate of the SIM IF is up to 4 Mbps, so HW designers should take care of the length and routing of the SIM IF to prevent potential EMC problems. 2.9.3 Power on The signal PON_1 is used to switch on LTE-NAD-A. As PON_1 is pulled against VMAIN internally, it is recommended to pull this input against GND using an open collector or open drain output only. 2.9.4 Reset PMD_RESIN_N is used to reset LTE-NAD-A. As PMD_RES_IN is pulled against VMAIN internally, it is recommended to pull this input against GND using an open collector or open drain output only. _______________________________________________________________________________________________________________ Seite 8 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 2.9.5 GPIOs There are 51 GPIOs available on LTE-NAD-A, some of them being part of the five GSBIs (see next section). They are used for different interfaces (see Table 1 and the following sections). For allocation of GPIOs/GSBIs to different configurations, please contact us. GPIOs and GSBIs share the same output pins and may not available when used as GSBI configuration. The following GPIOs do not belong to a GSBI bundle:

GPIO 47, 72, 82, 25, 28, 26, 27, 84, 80, 21, 23, 22, 24, 20, 1, 78, 79, 85, 86, 69, 0, 77, 65, 61, 68, 51, 54, 73, 48, 49, 53. The following GPIOs belongs to a GSBI bundle:

GPIO 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 29, 30. 2.9.6 GSBIs Five GSBIs (General Serial Bus Interfaces) are available in total, each of them consisting of four GPIOs. The reference voltage of the GSBIs is 1.8V. Available signals on GSBI bundles at the board to board connector:

- GSBI1:

- GSBI2:

- GSBI3:

- GSBI4:

- GSBI5:

GSBI1_0, GSBI1_1, GSBI1_2, GSBI1_3 (GPIO_29, 30, 2, 3) GSBI2_0, GSBI2_1, GSBI2_2, GSBI2_3 (GPIO_4, 5, 6, 7) GSBI3_0, GSBI3_1, GSBI3_2, GSBI3_3 (GPIO_8, 9, 10, 11) GSBI4_0, GSBI4_1, GSBI4_2, GSBI4_3 (GPIO_12, 13, 14, 15) GSBI5_0, GSBI5_1, GSBI5_2, GSBI5_3 (GPIO_16, 17, 18, 19) _______________________________________________________________________________________________________________ Seite 9 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 2.9.7 Module Pin-out Table 1 Pin Module Pin-out numbe Category 9x40 Pin name Description r 1 2 GND GND Ground USB3.0 MDM_USB_SS_TX_M USB 3.0 transmit minus 105 USB3.0 MDM_USB_SS_TX_P USB 3.0 transmit plus 3 GND 106 GND GND GND Ground Ground 4 USB3.0 (9x40) MDM_USB_SS_RX_M USB 3.0 receive minus 107 USB3.0 (9x40) MDM_USB_SS_RX_P USB 3.0 receive plus 5 GND 108 GND GND GND Ground Ground 6 PCIE/WLAN IF PCIE_REFCLK_M PCIe reference clock minus 109 PCIE/WLAN IF PCIE_REFCLK_P PCIe reference clock plus 7 GND 110 GND GND GND 8 PCIE/WLAN IF PCIE_TX_M Ground Ground PCIe transmit minus 111 PCIE/WLAN IF PCIE_TX_P PCIe transmit plus 9 GND 112 GND GND GND 10 PCIE/WLAN IF PCIE_RX_M 113 PCIE/WLAN IF PCIE_RX_P 11 GND 114 GND 12 USB 115 USB GND GND Ground Ground PCIe receive minus PCIe receive plus Ground Ground PMD_USB_ID USB high-speed data ID USB2_EXT_VBUS_DET External USB Vbus detection 13 GND GND 116 GPIO GPIO_86 Ground Configurable I/O 14 Reserved Reserved Inter-chip communication 117 GND GND Ground 15 Reserved Reserved Inter-chip communication 118 GND GND Ground 16 USB 119 USB MDM_USB_HS_DP MDM_USB_HS_DM USB high-speed data plus USB high-speed data minus 17 GND GND Ground _______________________________________________________________________________________________________________ Seite 10 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 120 SDIO IF/eMMC GPIO_96 / MDM_SDC1_DATA_4 Secure digital controller data bit 4 18 SDIO IF/eMMC GPIO_97 / MDM_SDC1_DATA_5 Secure digital controller data bit 5 121 SDIO IF/eMMC GPIO_98 / MDM_SDC1_DATA_6 Secure digital controller data bit 6 19 SDIO IF/eMMC GPIO_99 / MDM_SDC1_DATA_7 Secure digital controller data bit 7 122 SDIO IF GPIO_81 / SD_CARD_DET_N Secure digital card detection 20 SDIO IF MDM_SDC1_DATA_0 Secure digital controller data bit 0 123 SDIO IF MDM_SDC1_DATA_1 Secure digital controller data bit 1 21 SDIO IF MDM_SDC1_DATA_2 Secure digital controller data bit 2 124 SDIO IF MDM_SDC1_DATA_3 Secure digital controller data bit 3 22 GND GND Ground 125 SDIO IF MDM_SDC1_CMD Secure digital controller 2 command 23 SDIO IF MDM_SDC1_CLK Secure digital controller 2 clock 126 SIM1 VREG_L11_UIM1 Reference for UIM I/O pads 24 127 SIM1 GND Ground GPIO_79 / MDM_UIM1_CLK UIM1 clock 25 SIM1 GPIO_78 /MDM_UIM1_RESET UIM1 reset 128 SIM1 GPIO_77 / MDM_UIM1_DETECT UIM1 detect (non dual voltage) 26 27 28 SIM1 GND I2S GPIO_76 /MDM_UIM1_DATA UIM1 data GND Ground GPIO_15 / I2S_CLK I2S Data Clock 129 GND GND Ground 29 I2S MDM_MCLK Audio Master clock 130 GND GND 30 131 31 I2S I2S I2S GPIO_12 / I2S_WS GPIO_13 / I2S_DO GPIO_14 / I2S_DI 132 GND GND 32 133 33 UART4 GPIO_19 / ANT_SW_2 GPIO_18 / ANT_SW_1 Ground I2S word select I2S Data Output I2S Data Input Ground Antenna switch 2 Antenna switch 1 GPIO_17 / UART4_RX UART4 receive data 134 UART4 GPIO_16 / UART4_TX UART4 transmit data 34 GND 135 GND GND GND 35 GPIO GPIO_50 136 36 GND 137 GND 37 138 GPIO_23 / ANT_SW_4 GND GND MDM_RESOUT_N GPIO_22 / ANT_SW_3 Ground Ground Configurable I/O Antenna switch 4 Ground Ground Antenna switch 3 _______________________________________________________________________________________________________________ Seite 11 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 38 UART1 GPIO_21 / UART1_RX UART1 receive data 139 UART1 UART1_TX UART2 transmit data 39 GND GND 140 40 141 41 SPI SPI SPI SPI GPIO_7 / SPI_CLK GPIO_6 / SPI_CS_N GPIO_5 / SPI_MISO GPIO_4 / SPI_MOSI Ground SPI clock SPI chip select SPI master-in slave-out SPI master-out slave-in 142 SIM2 GPIO_2 / MDM_UIM2_RESET UIM2 reset 42 SIM2 GPIO_1 /MDM_UIM2_DETECT UIM2 detect (non dual voltage) 143 SIM2 GPIO_0 /MDM_UIM2_DATA UIM2 data 43 GND GND Ground 144 SIM2 VREG_L13_UIM2 Reference for UIM I/O pads 44 SIM2 GPIO_3 / MDM_UIM2_CLK UIM2 clock 145 GND 45 GND 146 GPIO 46 GPIO 147 GPIO 47 GPIO 148 GPIO 48 GPIO 149 GPIO 49 GPIO 150 GPIO 50 GPIO 151 I2C 51 I2C 152 GND 52 53 54 GND GND GND 153 GND GND GND GPIO_94 GPIO_80 GPIO_90 GPIO_82 GPIO_91 GPIO_87 GPIO_92 GPIO_88 GPIO_93 GPIO_89 GPIO_85 / I2C_SCL GPIO_84 / I2C_SDA GND GND GND GND GND Ground Ground Configurable I/O Configurable I/O Configurable I/O Configurable I/O Configurable I/O Configurable I/O Configurable I/O Configurable I/O Configurable I/O Configurable I/O I2C clock I2C data Ground Ground Ground Ground Ground 55 RF ANT_PTRX1 Primary cellular signal input/output 154 GND 56 GND 155 GND 57 GND 156 GND 58 GND GND GND GND GND GND GND Ground Ground Ground Ground Ground Ground _______________________________________________________________________________________________________________ Seite 12 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 157 GND GND Ground 59 MIPI GPIO_46 / RFFE4_DATA RF front end 4 interface data 158 GND 60 GND 159 GND GND GND GND Ground Ground Ground 61 MIPI GPIO_47 /RFFE4_CLK RF front end 4 interface clock 160 GND 62 63 GND GND GND GND GND 162 JTAG MDM_JTAG_TDI 64 GND GND Ground Ground Ground JTAG data input Ground 163 JTAG MDM_JTAG_TDO JTAG data output 65 GND GND Ground 164 JTAG MDM_JTAG_TMS JTAG mode select input 66 GND GND 165 JTAG MDM_JTAG_TRST_N 67 GND GND Ground JTAG reset Ground 166 JTAG MDM_JTAG_TCK JTAG clock input 68 GND GND Ground 167 JTAG MDM_JTAG_SRST_N JTAG reset for debug 69 GND GND Ground 168 JTAG MDM_JTAG_PS_HOLD Power supply hold signal to PMIC 70 GND GND 169 POWER VREG_L6_1P8 71 GND 170 GND GND GND Ground 1.8V output Ground Ground 72 RF ANT_DRX1 Diversity cellular signal input/output 171 GND 73 GND 172 GND GND GND GND 74 Reserved Reserved 173 GND 75 GND 174 GND 76 GND 175 GND 77 GND 176 GND 78 RF GND GND GND GND GND GND GND Ground Ground Ground Reserved Ground Ground Ground Ground Ground Ground Ground ANT_GNSS GNSS signal input/output _______________________________________________________________________________________________________________ Seite 13 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 79 80 177 GND GND GND GPIO_38 / GRFC12 GND Ground Ground 81 GPIO GPIO_69 Configurable I/O 178 82 GND GPIO_67 / EBI2_AD2/FBS_1 GND Ground 179 BOOT CONFIG GPIO_36 / FORCED_USB_BOOT Force USB boot control 83 GPIO 180 GPIO 84 GPIO 181 85 182 86 183 87 184 88 GND GPIO GPIO GND GPIO_8 GPIO_83 GPIO_9 GPIO_59 / NC GND GPIO_24 / EBI2_AD1/FBS_0 GPIO_10 MDM_MODE_0 GPIO_11 MDM_MODE_1 GND Configurable I/O Configurable I/O Configurable I/O Ground Configurable I/O TBD Configurable I/O TBD Ground 185 PCIE GPIO_65 / MDM_PCIE_WAKE_N PCIe host wake 89 Reserved Reserved Reserved 186 PCIE GPIO_61 / MDM_PCIE_RESET_N PCIe host reset 90 GND GND Ground 187 PCIE GPIO_64 / MDM_PCIE_CLKREQ_N PCIe clock request 91 GND GND 188 WLAN IF WLAN_PWR_REQ 92 GND GND 189 GPIO GPIO_60 93 WLAN IF WLAN_PWR_EN 190 GPIO GPIO_68 94 WLAN IF WLAN_SLP_CLK 191 BT IF BT_RESET_N Power-reset Ground Ground Configurable I/O Enable WLAN Power Configurable I/O Enable Bluetooth 95 PMIC (active PMD_RESIN_N Reset module low) 192 GND GND 96 Power-on PMIC

(active high) PON_1 Ground Turn on module 193 WLAN IF GPIO_95 / WLAN_EN Enable WLAN 97 194 WLAN IF CBL_PWR_N GPIO_52 / COEX_UART_TX UART transmit data _______________________________________________________________________________________________________________ Seite 14 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 98 MPP PMIC_MPP_4 Multipurpose Pin 195 WLAN IF GPIO_53 / COEX_UART_RX UART receive data 99 MPP 196 MPP PMIC_MPP_2 PMIC_MPP_6 100 GND GND_TO_VPH 197 GND GND_TO_VPH 101 POWER VPH_POWER 198 POWER VPH_POWER 102 POWER VPH_POWER 199 POWER VPH_POWER 103 POWER GND_TO_VPH 200 GND GND 104 HW_REV_RESISTOR Note: Pins should be grounded when not used in design. Multipurpose Pin Multipurpose Pin Ground Ground External supply voltage External supply voltage External supply voltage External supply voltage Ground Ground 2.10 Supply Voltage Absolute minimum/maximum supply voltages Nominal supply voltage Recommended supply voltage Voltage drop @ GSM power burst (33dBm) During Hi RF Power GSM bursts the power amplifier can draw peak currents > 2Amps at VMAIN. The voltage drop during the GSM burst shall not exceed 100mV. 3.9V ~ 4.1V 4V 4V

<100mV 2.11 Power Consumption TA = +25C, VPH_PWR =3.8V Voice call WCDMA BC1 Voice call WCDMA BC2 Voice call WCDMA BC5 Voice call WCDMA BC8 Voice call GSM850 Voice call GSM900 Voice call GSM1800 Voice call GSM1900 Output Power max. (typ. 23dBm)

~530mA

~570mA

~630mA

~580mA Output Power 0 dBm

~145mA

~145mA

~140mA

~140mA PCL 5 (typ. 32.5 dBm) PCL 19 (typ. 5dBm)

~260mA

~270mA

~65mA

~65mA PCL 0 (typ.30.5dBm) PCL 15 (typ.0dBm)

~165mA

~165mA

~65mA

~65mA _______________________________________________________________________________________________________________ Seite 15 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Standby current GSM Standby current WCDMA Standby current LTE LTE data call B3 LTE data call B7 LTE data call B20 DRX = 5 DRX = 7 DRX = 7 Output Power Output Power Tbd mA Tbd mA 2.12 Environmental Specification 2.12.1 Temperature Range Range Operating temp. range Extended operating temp. range

-25C +70C

-40C +85C Note 1 3GPP spec. conform Operational Performance might slightly deviate from 3GPP spec.

-40C +85C Storage temp. range Note 1: Due to temperature specification of the chipset, the temperature of the power manager and the temperature of the modem chip shall not exceed +85C. _______________________________________________________________________________________________________________ Seite 16 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Evaluation Kit 3 There are two types of evaluation boards fitted with the NAD V123x-0 modules:

The IFB-1 board allows to power-supply the module directly with external 4V along with sense signals. This 4V power-supply should be able to deliver 3.5A max. The IFB-4 board type takes 12V as input voltage, down-converted to 4V by on-board circuitry. Features:

-

-

-

-

-

-

-

USB 2.0 (micro USB) for USB to UART USB 3.0 (micro b) 2*SIM card slot Audio support with microphone and loudspeaker connectors JTAG connector for debug and programming 5 RF Antenna connector (PTRX,DRX,GNSS,WL,BT) 2* RS232 for UART 1 & 4 _______________________________________________________________________________________________________________ Seite 17 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe RF Connectors

- For Cellular RF measurements, use the PTRX and DRX antenna ports GNSS DRX PTRX Figure 1 Evaluation Kit for V123x-0. BT WLAN _______________________________________________________________________________________________________________ Seite 18 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe ON/OFF switch Only for 12 V supply 12 V DC Supply

(Top Connector positive, bottom connector ground) Figure 2 Power supply for Evaluation Kit for V123x-0. SIM slot 1(bottom)/2(Up) Figure 3 SIM card and USB interfaces for Evaluation Kit for V123x-0. USB 3port Micro USB 2.0 USB to UART _______________________________________________________________________________________________________________ Seite 19 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 4 AT Command interface The modules supports standard AT command as listed below. Commands are compliant to 3GPP TS 27.007 and TS 27.005 Command Description Comment AT+CMGF AT+CSCA AT+CMGS AT+CGMI AT+CGMM AT+CGMR AT+CGSN AT+CIMI AT+CMOD AT+CHUP ATD ATA ATH AT+CBST AT+CEER AT+CVHU AT+CREG AT+COPS AT+CLCK AT+CPWD AT+CLIP AT+CLIR AT+CCWA AT+CHLD AT+CUSD AT+CLCC AT+CPOL AT+CPAS AT+CFUN AT+CPIN AT+CSQ AT+CMER AT+CSIM AT+CRSM AT+CMEE AT+CGDCONT AT+CGEQREQ AT-CGATT AT+CGACT AT+CGPADDR AT+CGSMS ATE Message Format Service Centre Address Send Message Manufacturer Identification Request model identification Request revision identification Request product serial number Request international mobile subscriber identification Call mode Hang up call Initiate a CS or PS call or supplementary service Answer incoming CS call command Hangup CS call command Select bearer service type Extended error report Voice hangup control Network registration PLMN selection Facility lock Change password Calling line identification presentation Calling line identification restriction Call waiting Call related supplementary services Unstructured supplementary service data List current calls Preferred PLMN list Phone active status Set phone functionality Enter PIN Signal quality Mobile termination event reporting Generic SIM access Restricted SIM access Report mobile termination error Define PDP context Request 3G quality of service profile PS attach or detach PDP context activate or deactivate Show PDP address Select service for MO SMS messages Character Echo ON/OFF Only one Parameter is supported by the device. _______________________________________________________________________________________________________________ Seite 20 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Command Description Comment AT+CSMS AT+CSMP AT+CSDH AT+CSCB AT+CSAS AT+CRES AT+CMGL AT+CNMA AT+CMGC AT+CMMS AT+ATV AT+ATX AT+CNMI AT+CPMS AT+CMGW AT+CMSS AT+CMGD AT+CNUM AT+CPBS AT+CPBR AT+CPBW Check Message Service support Set Text Mode Parameters Show Text Mode Parameters Select Cell Broadcast Message Types Save Settings Restore Settings List messages New message acknowledgement Send Command More Messages to Send DCE response format Result code selection and call progress monitoring control New Message Indications to TE Preferred Message Storage Write Message to Memory Send Message from Storage Delete Messages Get MSISDN Select phonebook memory storage Read phonebook entries Writephonebook entry Only one Parameter is supported by the device. Only one Parameter is supported by the device. _______________________________________________________________________________________________________________ Seite 21 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Safety Recommendations according to EN60950-1 5 The V123x-0 devices must be supplied by a limited power source according to EN 60950-1. The clearance and creepage distances required by the end product must be withheld when the module is installed. The cooling of the end product shall not negatively be influenced by the installation of the module. _______________________________________________________________________________________________________________ Seite 22 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 6 RED/FCC/IC Regulatory Notices 6.1 Modifications WARNING: peiker acustic GmbH & Co. KG has not approved any changes or modifications to the V123x-0 device by the user. Any changes or modifications could void the users authority to operate the equipment. 6.2 Interference V1231-0 and V1233-0 devices comply with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) Those devices may not cause harmful interference, and

(2) Those devices must accept any interference received, including interference that may cause undesired operation. V1231-0 is a Class b digital apparatus compliant with Canadian ICES-003. V1231-0 est un appareil numrique de la classe b conforme la norme NMB-003 du Canada. V1231-0 est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. 6.3 FCC Class B Digital Device V1231-0 has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

-

- Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected.

- Consult the dealer or an experienced radio/TV technician for help. _______________________________________________________________________________________________________________ Seite 23 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 6.3 OEM Responsibilities Antenna

- The systems antenna(s) must be installed such that 20 cm is maintained between the antenna(s) and the body of the user or nearby persons.

- The V123x-0 transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The preceding statement must be included as a Caution statement in OEM product manuals in order to alert users of FCC RF Exposure compliance.

- Maximum authorized antenna gain: refer to the MPE test reports Power Supply

- The power supply of the host device embedding a V123x-0 module must fulfill the following requirements:

o Nominal supply voltage: 4V o Operating voltage range: 3.9V 4.1V o The above operating voltage range MUST never, under any circumstances

(including overshoot voltage and voltage drop), be exceeded. FCC Labeling Labeling requirements for a host device embedding V1231-0:

V1231-0 is labeled with its own FCC ID Number. If the FCC ID is not visible when V1231-

0 is installed inside another device, then the host device must contain the FCC ID number with the statement such as the following: "Contains Transmitter Module FCC ID: QWY-

V1231-0" or "Contains FCC ID: QWY-V1231-0"

Labeling requirements for a host device embedding V1233-0:

V1233-0 is labeled with its own FCC ID Number. If the FCC ID is not visible when V1233-

0 is installed inside another device, then the host device must contain the FCC ID number with the statement such as the following: "Contains Transmitter Module FCC ID: QWY-

V1233-0" or "Contains FCC ID: QWY-V1233-0"

IC Labeling Labeling requirements for a host device embedding V1231-0:

V1231-0 is labeled with its own IC ID Number. If the IC ID is not visible when V1231-0 is installed inside another device, then the host device must contain the IC ID number with the statement such as the following: "Contains Transmitter Module IC 6588A- V12310" or

"Contains IC 6588A- V12310". _______________________________________________________________________________________________________________ Seite 24 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 7 List of Acronyms 3 rd Generation Partnership Project Analog Digital Converter Abbreviated Dialing Number 3GPP ADC ADN A-GPS CP Assisted GPS Control Plane AMR AT AWS BER CLIP CLIR CSD DARP EDGE DTMF FCC FDN FTP GCF GSM GPIO GPRS GPS HSPA HW IC LED LTE MO MT OEM PCB PCM PDU PIN PTCRB RF RoHs UART USB USIM UMTS WCDMA Wideband Code Division Multiple Access Adaptive Multi Rate Attention Command Advanced Wireless Services Bit Error Rate Calling Line Identification Presentation Calling Line Identification Restriction Circuit Switch Data Downlink Advanced Receiver Performance Enhanced Data rates for GSM Evolution Dual Tone Multi Frequency Federal Communications Commission Fixed Dialing Number File Transfer Protocol Global Certification Forum Global System for Mobile communication General Purpose Input Output General Packet Radio Service Global Positioning System High Speed Uplink Packet Access Hardware Industry Canada Led Emitting Diode Long-Term Evolution Mobile Originated Mobile Terminated Original Equipment Manufacturer Printed Circuit Board Pulse Code Modulation Protocol Data Unit Personal Identification Number PCS Type Certification Review Board Radio Frequency Restriction of Hazardous Substances Universal Asynchronous Receiver and Transmitter Universal Serial Bus Universal Subscriber Identity Module Universal Mobile Telecommunications System _______________________________________________________________________________________________________________ Seite 25 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe