Insynctive SINGLE CHANNE REMOTE QUICK START GUIDE ithe product and its use. Before using this product, read the
() This Quick Start Guide is intended only to provide an overview complete Product Guide and warnings. videos and other Insynctive quick tips. WHATS INCLUDED:
SINGLE CHANNEL REMOTE: REMOTE is used to operate one or more INSYNCTIVE SHADES AND BLINDS. REMOTE is also used to teach up to three custom setpoints to INSYNCTIVE SHADES AND BLINDS. QUICK START GUIDE, CR2032 BATTERY WHATS REQUIRED: :
INSYNCTIVE SHADE OR BLIND (required sold separately): INSYNCTIVE SHADES AND BLINDS can be automatically raised and lowered to improve the comfort and convenience of your home. Minteger Gayle-OBrien-CO2L80FZFFRR Client: Pella Job #; PELLDS13006 Job Name: Garage Door Quick Guide Scan the QR Codesor visit pella.com/InsynctiveSingleChannel 7 Remote for complete Product Guide and warnings, instructional L of BATTERY COVER:
1. Get Started
* Install INSYNCTIVE SHADE OR BLIND following Quick Start Guide provided with the product. 2. Prepare SINGLE CHANNEL REMOTE
* Slide the battery cover in the direction of the arrow.
+ Remove battery tab.
+ Ensure battery is fully seated.
* Slide the battery cover back into closed position. 3. Sync REMOTE to SHADE or BLIND For ROOMSIDE SHADES AND BLINDS
+ Pull shade bottom rail downward at least six inches to activate the shade.
* Press and hold UP button on REMOTE until shade completes a quick up/down motion and then moves back to the top, fully open position. For DESIGNER BETWEEN THE GLASS SHADES AND BLINDS
* Hold Remote to Top Cover approximately 6 from the end to activate the shade. The shade will complete a quick up/down motion to acknowledge it
> is activated.
* Press and hold UP button on REMOTE until shade completes a quick up/down motion. To Printer: ==
File Name! LDS13006_Insynctive_GarageDoorS- | Trim: 3.5 x 5,25 Colors:
ensor_Quick_Guide.indd Cyan Bleed: 3.75 x 5.5 Fe certs low Print Scale: None I Black Date: 1-15-2014 3:50 PM 4. Test SHADE or BLIND
* Press the UP button to move the shade to the fully UP BUTTON open position. i * Press the DOWN button to move the shade to the DOWN. down position. BUTTON NOTE: Verify that the fabric and bottom rail do not rub or interfere with window, wall, or other obstructions. See SHADE or BLIND Product Guide for instructions on setting up and adjusting SHADE or BLIND. Have a home automation or security system? For instructions on how to sync a Pella Insynctive Shade or Blind, visit pella.com/InsynctiveHomeAutomation, NEED HELP WITH THE STEPS ABOVE? VISIT PELLA.COM/XXX OR CALL XXX-XXX-XXXX, FOR TROUBLESHOOTING INFORMATION AND VIDEOS, VISIT PELLA.COM/INSYNCTIVESINGLECHANNELREMOTE, READ THE FULL WARRANTY AND REGISTER YOUR INSYNCTIVE PRODUCTS AT XXXXX. Links: Garage Door Sensor.ai (18.07%), Insync-
tive_Garage_Door Sensor _Logo.ai (92.48%), In-
synctive Garage Door Sensor_Icon.ai (109.99%), Bridge _Angle.eps (33.6%), Garage Door with Sensor.eps (23.54%), Garage Door Sensor TILT, Failure to adhere to the warnings above may result in death, serious injury and/or loss of valuables. e Keep battery and other small parts out of reach of children. If swallowed, immediately seek medical help. Read the complete Product Guide for additional warnings and information. FCC Compliance and Industry Canada This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a different circuit from the receiver.
* Consult the dealer or an experienced radio/TV contractor for help. Changes or modifications not expressly approved by Pella Corporation could void the users authority to operate the equipment. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS. Lopration est soumise aux deux conditions suivantes: (1) cet appareil ne peut causer d'interfrences, et (2) cet appareil doit accepter toute interfrence, y compris les interfrences qui peuvent causer un mauvais fonctionnement de l'appareil. FCC ID: SO7-206A0000 IC: 11009A-206A0000 2014 Pella Corporation FINAL TO CLIENT (RED)