User Manual Product Name: SuperT Brand: SuperT Model: SuperT_V2, SuperT Manufacture: PengTai Interactive Advertising Co., Ltd. FCC Warning a15.19 Labeling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. b15.21 Changes or modification warning. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. c15.105 Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
interference
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. dRF warning for Portable device:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Technical details Iterms Model General Features SuperT_V2, SuperT SuperT LED panel209*239*6mm Brand Size Connection mode Bluetooth 4.0 Power source Battery LEDpanel Portable powerbank5V 2A 2600mA powerbank could normally be used for 3h with evenly distributed LED lights Notices Instructions Use the fastening tape to fix and install the LED panel. Iterms LED installation Connection mode Open the Bluetooth of your phone, keep the phone and SuperT distance inside 10m.search and connect to the device. It is recommended to use the official portable power bank. Charging instructions Storage Water penetration Dont fold or squeeze LED panel, and stored in a dry light place. In case of rain, sweat soaking and water splashing, please make sure its powered off and wipe it with a dry clean tower and placeit in a dry light place. If more questions, please call the customer service center. Heating problem Normally there will not be a heating problem when the device is working for long. But if there is, please stop using the device and contact us. FAQ What should I do if the LED panel gets dirty?
Wipe the panel with clean cloth; its not allowable to soak it in water and wash it. How to wash SuperT?
It is necessary to completely remove the outer intelligent equipment from the T-shirt before cleaning. What if Bluetooth connection fails?
1. Check whether the bluetooth of mobile phone and hardware deviceis normally opened;
2. Confirm the distance between phone and hardware device is less than 10m;
3. Reboot the device to reconnect. What if the LED panel doesnt react to the app operation?
Please check whether the Bluetooth of SuperT and cell phone is successfully connected. What if the color display of LED panel is abnormal?
1. The powerbank is out of power;
2. The cable contact is bad, please check whether the wiring is loose;
3. Check whether the equipment is wet or wetted by water. After-sale service and warranty?
All non-manmade quality problems of the external intelligent equipment, could enjoy one-year warranty service, beginning from the date of purchase (including the same day); for specific details, please contact the customer service office. About SuperT Operating instruction Step 1 Uncover the back of the Fastening Tape then using the five Fastening Tapes paste on the back of the LED display panel. (The size of the Fast ening Tape can be cut according to the position of the paste.) Step 2 Uncover the back of other side of the Fastening Tape. Then place the LED panel on the clothe. Step 3 Connect the charging source to the LED display controller and ensure that the device is properly turned on, and the device automatically turns on the Bluetooth function. Long press for one second to switch the reserved pattern. Step 4 Open superT APP and Bluetooth. Search and connect the device, the Bluetooth connection is suitable for 10m. (Device number please see the back of the controller) APP instruction Step 1 Scan the QR-Code to download the app, or download the installation in the application store. Step 2 Open the application, connect the device via Bluetooth, please turn on the controller . Choose your device to connect. Step 3 Setting the pattern When you successfully connect the APP click on the icon to change the pattern Setting page Setting the speed of Animation Setting the brightness of the LED Sleeping Turn off the LED panel Step 4 All the pattern in the library Check the pattern showing in the LED screen Click order buttoncharging order of the patterns Step 5 DIY Pattern Select colourdrag and draw on the Screen Click save to create new pattern Step 6 Select colourdrag and draw on the Screen Click plus to add a new frame. Then keep drag and draw on the Screen. Click save to create new pattern