FCC ID: BOU-AD7000W Wireless speaker with AirPlay

Register your product and get support at www.philips.com/welcome EN User manual Contents 1 Important Safety Notice 2 Your Entertainment System Introduction Whats in the box What else you need Overview of the main unit Get started to use AirPlay 3 Prepare Connect power Turn AD7000W on 4 4 5 8 8 8 8 9 9 10 10 10 4 Connect to your home Wi-Fi network for 11 11 12 AirPlay Scenario 1: Connect to a WPS router Scenario 2: Connect to a non-WPS router 5 Play 20 Stream audio from your iTunes music library to 20 AD7000W 21 Control play 21 Use advanced sound settings Play/charge your iPod/iPhone/iPad through USB 22 socket 22 Play from an external device 23 Update rmware 6 Product information Specications 7 Troubleshooting 26 26 27 EN 3 1 Important k Only use attachments/accessories specied by the manufacturer. l Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. m Unplug this apparatus during lightning storms or when unused for long periods of time. n Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. o Battery usage CAUTION To prevent battery leakage which may result in bodily injury, property damage, or damage to the unit:

Install all batteries correctly, + and - as marked on the unit. Remove batteries when the unit is not used for a long time. Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/

hazardouswaste/perchlorate. p Apparatus shall not be exposed to dripping or splashing, keep it away from direct sunlight,naked ames or heat. Safety Important Safety Instructions a Read these instructions. b Keep these instructions. c Heed all warnings. d Follow all instructions. e Do not use this apparatus near water. f Clean only with dry cloth. g Do not block any ventilation openings. Install in accordance with the manufacturers instructions. h Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce heat. i Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet. j Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 4 EN Warning Never remove the casing of this apparatus. Never lubricate any part of this apparatus. Never place this apparatus on other electrical equipment. Keep this apparatus away from direct sunlight, naked ames or heat. Ensure that you always have easy access to the power cord, plug or adaptor to disconnect this apparatus from the power. Risk of overheating! Never install this apparatus in a conned space. Always leave a space of at least four inches around this apparatus for ventilation. Ensure curtains or other objects never cover the ventilation slots on this apparatus. Notice Notice of compliance Modications The user is cautioned that changes or modications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC & RSS compliance statement This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

a This device may not cause harmful interference, and b This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement This equipment complies with FCCs and ICs RF radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must be installed and operated to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. Installers must ensure that 20cm separation distance will be maintained between the device

(excluding its handset) and users. FCC rules This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Canada:

This Class B digital apparatus complies with Canadian ICES-003. EN 5 Disposal of your old product and batteries Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. Never dispose of your product with other household waste. Please inform yourself about the local rules on the separate collection of electrical and electronic products and batteries. The correct disposal of these products helps prevent potentially negative consequences on the environment and human health. Your product contains batteries, which cannot be disposed of with normal household waste. Please inform yourself about the local rules on separate collection of batteries. The correct disposal of batteries helps prevent potentially negative consequences on the environment and human health. Please visit www.recycle.philips.com for additional information on a recycling center in your area. Powered by an ENERGY STAR qualied adaptor for a better environment. Modications Modications not authorized by the manufacturer may void users authority to operate this product. Disposal of your old product and batteries Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. 6 EN Never dispose of your product with other household waste. Please inform yourself about the local rules on the separate collection of electrical and electronic products and batteries. The correct disposal of these products helps prevent potentially negative consequences on the environment and human health. Your product contains batteries, which cannot be disposed of with normal household waste. Please inform yourself about the local rules on separate collection of batteries. The correct disposal of batteries helps prevent potentially negative consequences on the environment and human health. Please visit www.recycle.philips.com for additional information on a recycling center in your area. Information about the use of batteries:

Caution Risk of leakage: Only use the specied type of batteries. Do not mix new and used batteries. Do not mix different brands of batteries. Observe correct polarity. Remove batteries from products that are not in use for a longer period of time. Store batteries in a dry place. Risk of injury: Wear gloves when handling leaking batteries. Keep batteries out of reach of children and pets. Risk of explosion: Do not short circuit batteries. Do not expose batteries to excessive heat. Do not throw batteries into the re. Do not damage or disassemble batteries. Do not recharge non-rechargeable batteries. Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene

(bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment. Made for iPod, Made for iPhone, and Made for iPad mean that an electronic accessory has been designed to connect specically to iPod, iPhone, or iPad, respectively, and has been certied by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless performance. AirPlay, iPod, and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. iPad is a trademark of Apple Inc. Class II equipment symbol:

CLASS II apparatus with double insulation, and no protective earth provided. Note The type plate is located on the bottom of the apparatus. EN 7 2 Your Entertainment System Congratulations on your purchase, and welcome to Philips! To fully benet from the support that Philips offers, register your product at www.philips.com/welcome. If you contact Philips, you will be asked for the model and serial number of this apparatus. The model number and serial number are on the bottom of the apparatus. Write the numbers here:

Model No. __________________________ Serial No. ___________________________ Introduction Apple AirPlay technology enables you to play your iTunes music library, hosted on a Mac, PC, iPhone, iPod touch, or iPad on any AirPlay-

enabled device (for example, your AD7000W) connected to the Wi-Fi network. With an AirPlay-enabled device (for example, your AD7000W), you can:

stream audio from your iTunes music library to any room in your house choose which AirPlay-enabled devices you want to play music on (if you have more than one such devices in your house) stream audio to multiple AirPlay-

enabled devices at the sam time (from the iTunes music library on your PC/Mac only) Tip Please visit www.philips.com/welcome for information about more Philips AirPlay-enabled devices. 8 EN With AD7000W, you can also:

charge your iPod/iPhone/iPad through the USB socket with an Apple USB cable (not supplied). play your iTunes music library on your iPod/iPhone/iPad through the USB socket directly while charging. play music from other audio devices through the MP3-LINK socket. Whats in the box Check and identify the contents of your package:

Main unit (with a built-in Wi-Fi module) 1 x AC power adapter 1 x MP3 link cable User manual (in CD-ROM) Quick start guide What else you need To stream audio wirelessly by AirPlay, you need:

A Wi-Fi certied router A host for your iTunes music library, for example, an iPod touch/iPhone/

iPad installed with iOS 4.3 (or later) or a Wi-Fi enabled PC/Mac installed with iTunes 10 (or later) Your AD7000W should be connected to the same local network as your iTunes host device through the Wi-Fi router. List of compatible iTunes host devices for AirPlay In terms of AirPlay, AD7000W is compatible with:

a Wi-Fi enabled PC/Mac installed with iTunes 10 (or later); and the following iPod/iPhone/iPad models installed with iOS 4.3 (or later):

iPad 2 a a iPad iPhone 4 iPhone 3GS iPod touch (2nd, 3rd, and 4th generation) Overview of the main unit a Power indicator Turn the unit on/off. b f f g g c +/-

Adjust volume.

(Press and hold both buttons) reset the unit. d WI-FI SETUP button/indicator Connect the unit to a Wi-Fi network. Show the Wi-Fi connection status of the unit. e MP3-LINK Connect an external audio player through the supplied MP3 link cable. f DC IN Connect the power adaptor. g USB Connect an iPod/iPhone/iPad through an Apple USB cable (not supplied). Get started to use AirPlay To get started with AirPlay, you need to:

b b c c d d e e 1 Upgrade your iPod touch/iPhone/iPad to the latest iOS version (iOS 4.3 or later). Or install the latest version of iTunes

(iTunes 10 or ater) on your PC/Mac. 2 Connect power to AD7000W, then turn it 3 Connect AD7000W to your existing home Wi-Fi network (see Connect to your home Wi-Fi network for AirPlay on page 11). 4 Make sure that your iPod touch/iPhone/

on (see Prepare on page 10). iPad or PC/Mac are also connected to the same Wi-Fi network. EN 9 The boot-up takes about 35 seconds. During boot-up, the Wi-Fi SETUP indicator on the back of the unit blinks green quickly. After boot-up, if no Wi-Fi connection has been set up for AD7000W, the Wi-Fi SETUP indicator starts to blink green slowly. again. To switch the unit to Eco standby mode, press To switch the unit on from Eco standby mode, press again. Tip If the unit stays idle for more than 30 minutes, the unit turns off automatically. You can change this setting on the Philips Fidelio application available on the App Store. It is a free application offered by Philips. 3 Prepare Always follow the instructions in this chapter in sequence. Connect power Risk of product damage! Make sure that the power supply voltage matches the voltage printed on the bottom of the unit. Risk of electric shock! When you unplug the AC adaptor, always pull the plug from the socket. Never pull the cord. Before you connect the AC adaptor, make sure that you have completed all the other connections. Caution Connect the AC power cord to the DC IN socket on the back of the unit. the wall power socket. Turn AD7000W on 1 Press on the back to turn the unit on. 2 Wait for successful boot-up of the unit. 10 EN 4 Connect to your home Wi-

Fi network for AirPlay To connect AD7000W to your existing home Wi-Fi network, you need to apply your home Wi-Fi settings to AD7000W. You can do this in two ways (depending on which type of Wi-Fi router you use):

Automatically - if your Wi-Fi router is WPS (Wi-Fi Protected Setup)-

enabled and supports PBC (Push Button Connection) (see Scenario 1:

Connect to a WPS router on page 11) Manually - if your Wi-Fi router does not support WPS (see Scenario 2:

Connect to a non-WPS router on page 12) Once connected successfully, AD7000W will remember your home Wi-Fi settings. Then you can enjoy AirPlay whenever AD7000W is powered on and connected to your home Wi-

Fi network automatically. Before connection of AD7000W to you home Wi-Fi network, check the points below. 1 Make sure that your Wi-Fi router is powered on and working properly. 2 Make sure that AD7000W has been powered on and booted up successfully

(see Turn AD7000W on on page 10). Identify the type of your Wi-Fi router (see the user manual of your Wi-Fi router for details). 3 Scenario 1: Connect to a WPS router Note WPSWPS 1 Press the WPS button on your home Wi-Fi Before you press any button on AD7000W, make sure that AD7000W has been booted up successfully (see Turn AD7000W on on page 10). router. 2 Shortly after step 1, press Wi-Fi SETUP on the back of AD7000W. The Wi-Fi SETUP indicator blinks red, yellow and green alternately. Within 2 minutes, the WI-FI SETUP indicator stops blinking and stays green, and the unit beeps. EN 11 AD7000W is connected to your home Wi-Fi network successfully. Tip For some Wi-Fi routers, you may need to hold the WPS button for Wi-Fi connection or enable the WPS PBC function from the router conguration pages. See the user manuals of the specic routers for details. If the Wi-Fi SETUP indicator on AD7000W blinks yellow, it means that the Wi-Fi connection has failed. Please wait for 2 minutes and try again. If the problem remains, try to set up the Wi-Fi connection manually

(see Scenario 2: Connect to a non-WPS router on page 12). If the Wi-Fi connection fails again, press and hold both the + and - buttons on the back of AD7000W to reset it, and then try again. Scenario 2: Connect to a non-WPS router Note You can also follow the procedures below to connect AD7000W to a WPS router manually. To connect AD7000W to a Wi-Fi router manually, you need access to AD7000Ws built-in conguration web page for change of its internal Wi-Fi settings. To do so, you need a Wi-Fi enabled device with an Internet browser 12 EN for temporary Wi-Fi connection to AD7000W. The Wi-Fi enabled device can be an iPod touch/

iPhone/iPad or a Wi-Fi enabled PC/Mac. Follow the sequence below for connection of AD7000W to a non-WPS wi-Fi router. 1 Collect settings of your home Wi-Fi router and write down on paper for use during AD7000W Wi-Fi setup (see Collect settings of your home Wi-Fi router on page 12). 2 Switch AD7000W to Assisted Wi-Fi Setup mode (see Switch AD7000W to Assisted Wi-Fi Setup mode on page 13). A new Wi-Fi network created by AD7000W will appear, with the network name (SSID) of Philips Fidelio AirPlay. 3 Connect your Wi-Fi enabled device to the created new Wi-Fi network temporarily

(see Connect your Wi-Fi enabled device to the newly created Wi-Fi network on page 13). 4 Open the built-in web page of AD7000W with the Internet Browser of your Wi-Fi enabled device (see Open the built-in web page of AD7000W on page 15). 5 Change the internal Wi-Fi settings of AD7000W based on the settings you wrote on paper at step 1 (see Change the internal Wi-Fi settings of AD7000W on page 16). 6 Restore your Wi-Fi enabled device back to your existing home Wi-Fi settings (see Restore your Wi-Fi enabled device back to your existing home Wi-Fi setting on page 18). Collect settings of your home Wi-Fi router Note Always consult the user manual of your home Wi-Fi router for detailed instructions. 1 Connect your Wi-Fi enabled device to 2 Launch the Internet browser (for example, your existing home Wi-Fi network. Apple Safari or Microsoft Internet Explorer) on your Wi-Fi enabled device. 3 Enter the IP address of your home Wi-Fi router at the web page address bar of your Wi-Fi enabled device. The conguration page of your home Wi-Fi router is displayed. 4 Find the Wi-Fi settings tab and write down the following information on paper:

A Network name (SSID) B Wi-Fi security mode (usually WEP, WPA or WPA2 if enabled) C Wi-Fi password (if Wi-Fi security is enabled) D DHCP mode (enabled or disabled) E Static IP address settings (if DHCP mode is disabled) Switch AD7000W to Assisted Wi-Fi Setup mode Before you press any button on AD7000W, make sure that AD7000W has been booted up successfully (see Turn AD7000W on on page 10). Note Press and hold Wi-Fi SETUP on the back of AD7000W for more than 5 seconds. The Wi-Fi SETUP indicator blinks green and yellow alternately. A new Wi-Fi network created by AD7000W will appear, with the network name (SSID) of Philips Fidelio AirPlay. It may take up to 45 seconds for successful creation of this new Wi-Fi network. Note After you nish manual Wi-Fi setup for AD7000W, the new Wi-Fi network created by AD7000W will disappear. If you fail to enter Assisted Wi-Fi Setup mode, power off AD7000W and power on it, then try again after successful boot-up. Make sure that there are no other Philips AirPlay-

enabled devices in Assisted Wi-Fi Setup mode at the same time. Multiple Wi-Fi networks created this way may interfere with each other. Connect your Wi-Fi enabled device to the newly created Wi-Fi network The new Wi-Fi network created by AD7000W only allows access of one Wi-Fi enabled device. To avoid interference from any other Wi-Fi devices, you are recommended to temporarily disable the Wi-Fi function on your other Wi-Fi devices. Option 1: Use your iPod touch/iPhone/iPad 1 Select Settings -> Wi-Fi on your iPod touch/iPhone/iPad. EN 13 2 Select Philips Fidelio AirPlay from the list of available networks. 3 Wait until successful Wi-Fi connection on your iPod touch/iPhone/iPad. Philips Fidelio Airplay Philips Fidelio Airplay of your iPod touch/iPhone/iPad. is displayed at the upper left corner 14 EN Tip If Philips Fidelio AirPlay is not in the list, try to scan the available Wi-Fi networks again. Use your Wi-Fi enabled PC/Mac Note panel on your PC/Mac. 1 Open the Wi-Fi setup tool or control See the user manual of your PC/Mac for how to connect your PC/Mac to a Wi-Fi network. During Wi-Fi network connection, do not connect any network cable to your PC/Mac. 2 Scan the available Wi-Fi networks. 3 Select Philips Fidelio AirPlay from the list of available networks. 4 Wait until successful Wi-Fi connection on your PC/Mac. Tip If Philips Fidelio AirPlay is not in the list, try to scan the available Wi-Fi networks again. Open the built-in web page of AD7000W 1 Launch Apple Safari browser or any other Internet browser on your Wi-Fi enabled device. 2 Type in 192.168.1.1 at the browser address bar and conrm. The AD7000W conguration web page is displayed. 192.168.1.1 192.168.1.1 The Bookmarks menu is displayed. 2 Tick Include Bonjour for Bookmarks bar. If you use Safari on your Wi-Fi enabled PC/

Mac, you can also select Philips_Fidelio XXX from the Bonjour pull-down list to enter the AD7000W conguration web page directly. 1 Click

-> Preferences. EN 15 The AD7000W conguration web Bonjour pull-down list shown at the bookmarks bar. 3 Select Philips_Fidelio XXX from the page is displayed. Change the internal Wi-Fi settings of AD7000W On the AD7000W conguration web page, you can change the internal Wi-Fi settings of AD7000W for connection of AD7000W to your existing home Wi-Fi network. Note Make sure that the settings at steps 2 to 4 below match your home Wi-Fi network settings you wrote on paper. 1 Select the Network Conguration tab. 16 EN Network Configuration Network Configuration 2 Select your network name (SSID) from the pull-down list of Service Set ID (SSID). 3 Enter your network key if required. 4 If DHCP mode is disabled in your home Wi-Fi router, tick DHCP under Advance Setting. 5 Click Apply at the bottom of the page to apply your new settings. A menu for conrmation of your change pops up. 6 Click OK on the popup menu to conrm After a while, the WI-FI SETUP indicator on the back of AD7000W stops blinking and stays green, and the unit beeps. AD7000W is connected to your existing home Wi-Fi network successfully. your change. EN 17 Note touch/iPhone/iPad. Make sure that the settings at steps 2 to 3 below match your home Wi-Fi network settings you wrote on paper. 1 Select Settings -> Wi-Fi on your iPod Or open the list of available Wi-Fi Restore your Wi-Fi enabled device back to your existing home Wi-Fi setting Note networks on your PC/Mac. 2 Select your network name (SSID) from the If the WI-FI SETUP indicator on AD7000W does not stay green steadily, it means that the Wi-Fi connection has failed. Please power off both your Wi-Fi router and AD7000W and then power on them again to see whether AD7000W can be connected to your home Wi-F network. If the problem remains, try the above procedures again. After you nish the above changes or power-off and power-on of AD7000W, the new Wi-Fi network created by AD7000W will disappear. If you like, you can change the name of your AD7000W in Airplay Device Name on the AD7000W conguration web page. This is helpful when you have multiple Philips AirPlay-enabled devices in your house and you need to distinguish between them. If you want to enter the network name (SSID) manually

(for example, if you want to hide your SSID), select CONFIGURE MANUALLY from the pull-down list at step 2 in the above. list of available wireless networks. Tip 18 EN 3 Enter the network key if required. your home Wi-Fi network. 4 Wait until successful Wi-Fi connection to EN 19 4 Select a media le and start play. 5 Wait until successful audio streaming to AD7000W. Note If you fail to hear music after successful setup, do one of the following on your iPod touch/iPhone/iPad:

(1) Disconnect and then re-connect to the same Wi-Fi router again;

(2) Close all applications running at the background;

(3) Power off and then power on your iPod touch/

iPhone/iPad again. 5 Play Stream audio from your iTunes music library to AD7000W Note touch/iPhone/iPad. Make sure that your iTunes host device is connected to the same Wi-Fi network as AD7000W. Your iTunes device can be an iPod touch/iPhone/iPad installed with iOS 4.3 (or later) or a Wi-Fi enabled PC/Mac installed with iTunes 10 (or later). Stream from your iPod touch/iPhone/

iPad 1 Launch the iPod application on your iPod 2 Tap on the AirPlay icon. 3 Select Philips_Fidelio XXXX (or user customized name) from the AirPlay list. EN 20 your PC/Mac. user customized name) from the AirPlay Stream from your PC/Mac 1 Launch iTunes 10 (or a later version) on 2 Click the AirPlay icon on the window. 3 Select Philips_Fidelio_AirPlay XXXX (or list. 4 Select a media le and start play. 5 Wait until successful audio streaming to AD7000W. Tip When you stream audio from your iTunes music library on a PC/Mac, you can select more than one AirPlay-

enabled devices (if available) at step 3 to stream music to all of them at the same time. If you are using an earlier version of iTunes, the AirPlay icon may be instead of

. Control play You can select different play options from either your iTunes host device or AD7000W. Note The operations below are based on AD7000W. Make sure that you have successfully streamed audio from your iTunes music library to AD7000W. To start or pause play, press To adjust volume, press +/- repeatedly. Use advanced sound settings If your iTunes host device is an iPod touch/

iPhone/iPad:

For advanced sound settings and additional features, you can use your iPod touch/iPhone/

iPad to download the Philips Fidelio application from Apple App Store. It is a free application from Philips. If your iTunes host device is a Wi-Fi enabled PC/Mac:

For advanced sound settings, you can use the equalizer available on iTunes directly (View ->

Show Equalizer). Tip See the iTunes help documentation for more details. EN 21 Compatible iPod/iPhone/iPad The USB socket supports play and charge of the following iPod, iPhone, and iPad models. iPad 2 iPad iPhone 4 iPhone 3GS iPhone 3G iPhone iPod classic iPod 5G iPod 4G iPod nano (1st, 2nd, 3rd, 4th, 5th, and 6th generation) iPod touch (1st, 2nd, 3rd, and 4th generation) iPod mini Note iPod with color display, iPod classic, and iPod with video are not compatible with power charging. Play from an external device You can also listen to an external audio player through the unit. Play/charge your iPod/iPhone/

iPad through USB socket Note You can play or charge your iPod/iPhone/iPad through the USB socket with an Apple USB The USB socket is only compatible with iPod/iPhone/

iPad. To avoid possible damage to AD7000W, never try to connect devices other than iPod/iPhone/iPad to the USB socket on AD7000W. cable (not supplied). Connect an Apple USB cable (not socket on the back of supplied) to:

the USB AD7000W. the dock connector on your iPod/

iPhone/iPad. Tip If you have stopped audio streaming by AirPlay, after successful USB connection, the unit switches to the USB source automatically. 22 EN Connect the supplied MP3 link cable to:

the DC IN socket on the back of the unit. the headphone jack on an external audio player. www.philips.com/support www.philips.com/support Download the update le 1 On your PC/Mac, go to www.philips.com/

2 Enter the model number to nd the latest 3 rmware upgrade le available. Save the upgrade le to your hard drive. support. DS XXXX DS XXXX Note If you have stopped both audio streaming by AirPlay and play through the USB socket, the unit switches to the MP3 link source automatically. Update rmware Note You can only update the rmware from a PC/Mac. Update from the conguration page Warning Always connect your AD7000W to AC power for rmware upgrade. Never power off your AD7000W during rmware upgrade. Note To use an Internet browser other than Apple Safari on your PC/Mac, remember to go to the Wi-Fi router conguration page and write down the IP address of your AD7000W. See the user manual of your Wi-Fi router for how to nd the IP addresses of devices connected to the Wi-Fi router. 1 Power on AD7000W (see Turn AD7000W on on page 10). It takes about 35 seconds for the unit to boot up. During boot-up, the WI-FI EN 23 SETUP indicator on the back of the unit blinks green quickly. After boot-up, you can hear a beep and the WI-FI SETUP indicator turns to green steadily. AD7000W is connected to the last congured Wi-Fi network automatically. 2 Make sure that AD7000W and your PC/Mac are connected to the same Wi-Fi router. 3 Open Apple Safari on your PC/Mac, then select Philips_Fidelio XXX from the Bonjour pull-down list. Or open any other Internet browser on your PC/Mac, then type in the IP address of AD7000W (available on the Wi-Fi router conguration page) at the address bar. The AD7000W conguration web page is displayed. 4 Select the Firmware Update tab, then the next page. follow the on-screen instruction to enter 24 EN compare the current and new le versions. downloaded rmware update le, then 5 Click Choose File to select the click Open. 6 Click Upload to upload the le, then 7 After you make sure that the downloaded 8 At completion of the update process, click Ok to conrm. update le is the latest, click Ok to start rmware update. A progress bar is displayed. Firmware upload status: 100% completed. Firmware upload status: 100% completed. The upload process finished successfully. The upload process finished successfully. Wait until the new firmware is started and then press the button. Wait until the new firmware is started and then press the button. Note In case the rmware update fails, you can try the above procedures again. After successful rmware update, if there is any problem with the Wi-Fi connection, press and hold both the + and - buttons on AD7000W for more than 5 seconds at the same time to reset the device, and then try to set up the Wi-Fi network for AD7000W again (see Connect to your home Wi-Fi network for AirPlay on page 11). EN 25 General information AC power Operation Power Consumption Dimensions

- Main Unit (L x W x H) Weight

- With Packing

- Main Unit Input: 100 - 240 V~, 50/60 Hz 1.2 A Output: 12 V 3.0 A 10 W 298 x 106 x 168 mm 4.83 kg 1.31 kg 6 Product information Note Product information is subject to change without prior notice. Specications Amplier Rated Output Power Frequency Response Signal to Noise Ratio > 90 dB MP3 Link 2 X 5 W RMS 20 - 20000 Hz, 3 dB 650 mV RMS 20 kohm Speakers Speaker Impedance Speaker Driver Sensitivity 8 ohm 62 mm full range 78 dB/m/W 802.11n, backwards compatible to 802.11b/g WEP (64 or 128 bit), WPA/WPA2 (8-63 characters) 2412 - 2462 MHz (CH1-CH11)

(for /79, /37, /55, /97) 2412 - 2472 MHz (CH1-CH13)

(for /12, /05) Yes Wireless Wireless standard Wireless security Frequency range Wireless protected setup

(WPS) 26 EN 7 Troubleshooting Warning Never remove the casing of this apparatus. To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this apparatus, check the following points before requesting service. If the problem remains unsolved, go to the Philips web site (www. philips.com/welcome). When you contact Philips, ensure that the apparatus is nearby and the model number and serial number are available. No power Make sure that the AC power plug of the device is connected properly. Make sure that there is power at the AC outlet. No sound Adjust the volume. Check the Wi-Fi network connection. Set up the network again if needed (see Connect to your home Wi-Fi network for AirPlay on page 11). No response from the unit Press and hold both the + and - buttons on AD7000W for more than 5 seconds to reset the device. Then set up the Wi-Fi network for AD7000W again (see Connect to your home Wi-Fi network for AirPlay on page 11). Disconnect and reconnect the AC power plug, and then switch on the device again. Wi-Fi network connection failed Check if your Wi-Fi router is Wi-Fi 802.11b/g certied. This device is only compatible with Wi-Fi 802.11b/g certied routers. If your Wi-Fi router is Wi-Fi 802.11n certied, make sure to enable the 802.11b/

g mode. AD7000W does not support connection to routers with 802.11n only. This device does not support the WPS-

PIN method. If your Wi-Fi router supports WPS and the WPS-PBC method but fails to connect to AD7000W, try the manual Wi-Fi setup method (see Scenario 2: Connect to a non-WPS router on page 12). Enable SSID broadcast on the Wi-Fi router. Avoid using Wi-Fi channel which is using or much overlapped by the nearby Wi-Fi network. Keep away from potential sources of interference which may affect Wi-Fi signal, such as microwave ovens. If you fail to use your PC for Wi-Fi network setup, check whether your PC is using a Wi-Fi network. You cannot use Ethernet connection for AirPlay network setup. If the problem remains, it is strongly recommended to use iPod Touch/iPhone/

iPad/Mac to do the rst-time Wi-Fi setup as some PC settings may affect the Wi-Fi network setup. Make sure that the SSID name of your home router consists of normal characters or digits, with no space or special characters like %/#/* inserted. If you choose to rename the AirPlay device Philips_Fidelio XXXX in the setting menu, do not use special characters or symbols. For some new types of Wi-Fi routers, a network name (SSID) may be created automatically when you use WPS for connection. Always change the default network name (SSID) to a simple one that consists of alphanumerical characters, and also change the Wi-Fi security mode to secure your network. Occasional breaking of AirPlay music streaming Do one or all of the following:

EN 27 Move AD7000W closer to your Wi-Fi router. Remove any obstacles between AD7000W and your Wi-Fi router. Enable the Auto Channel Scan option (if available on the Wi-Fi router). Enable the Quality of Service (QoS) option (if available on the Wi-Fi router). Turn off other Wi-Fi routers. No AirPlay icon on my iTunes host device Make sure that AD7000W is already connected to your home Wi-Fi network. Before you open iTunes, make sure that you have enabled Bonjour service in your PC. Take Windows XP for example:

to enable the service, you can click Start->Control Panel, and double-click Administrative Tools-> Services->Bonjour Service, then click Start followed by OK on the pop-up menu. If the problem remains, try to restart AD7000W. AirPlay connection failed with Mac or PC Temporarily disable the rewall and security software to see whether it blocks the ports that AirPlay uses to stream content. See the help documentation of your rewall and security software on how to unblock the ports. Check if your network speed is fast enough

(in cases where multiple devices share the same router, the AirPlay performance may be affected). Turn off the other devices connected to your home router. In case of audio streaming break or disconnection when you use iPod Touch/

iPhone/iPad/iMac/PC for AirPlay, restart your iPod Touch/iPhone/iPad, iTunes or AD7000W. Browsing Internet content like news, music, video and etc. via your home router may affect the AirPlay performance. In case of AirPlay break or disconnection, it is recommended to stop any Internet surng or disconnect from the Internet. 28 EN 2011 Koninklijke Philips Electronics N.V. All rights reserved. Document order number: 000000000000