Confidential Document Philips Electronics Singapore Pte Ltd User Manual Setup Procedures
Of Information For Used 2.4GHz RF Remote Control
(RC1974401/01BRF) &
2.4GHz RF USB Receiver (OVU700003/01RF) Page 1 of 15 Page 3 of 16 Page 4 of 16 Page 12 of 16 Page 13 of 16 Page 13 of 16 Page 13 of 16 Page 14 of 16 Page 14 of 16 Confidential Document Philips Electronics Singapore Pte Ltd Table of contents 1. 2. 3. 3.1 3.2 3.3 3.4 3.5 FCC Statatement Setup Procedures Information For Used General Stuck key function Sleep mode Key press Pairing Page 2 of 15 Confidential Document Philips Electronics Singapore Pte Ltd 1. FCC Statement FCC Part 15.19 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device maynot cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. No special accessory is required to enable the equipment to comply with the emission limits. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. Page 3 of 15 Confidential Document Philips Electronics Singapore Pte Ltd 2. Setup Procedures Setup Procedures of 2.4GHz RF Remote Control and 2.4GHz RF USB Receiver Plug into USB port USB port 2.4GHz RF USB Receiver Picture 1: USB port and 2.4GHz RF USB Receiver plug into USB port. Page 4 of 15 Confidential Document Philips Electronics Singapore Pte Ltd Picture 2: 2.4GHz RF Remote control with packaging (front and rear side). Picture 3: Remove the battery lid by pressed the hook down the battery lid and lift it up. Press the hook down and lift up the lid Picture 4: Insert the batteries (AAA type) with correct polarity. Page 5 of 15 Confidential Document Philips Electronics Singapore Pte Ltd Picture 5: Closed up the battery compartment with battery lid. Lift up the LCD display after release the catcher Press to right hand side to release the catcher Picture 6: Lift up the notebook LCD display by release the catcher. Picture 7: Press the switch to turn on the notebook. Page 6 of 15 Confidential Document Philips Electronics Singapore Pte Ltd Picture 8: Process of loading Windows Vista. Picture 9: Close the application as above by click the X icon at upper right hand side as Picture 10. Picture 10: The X icon located at right hand side, upper corner. Page 7 of 15 Confidential Document Philips Electronics Singapore Pte Ltd Picture 11: Using cursor to click the Start icon located at left hand side, lower corner. Picture 12: Select and click the WordPad application program. Page 8 of 15 Confidential Document Philips Electronics Singapore Pte Ltd Picture 13: The WordPad application software. Picture 14: Press Digit 5 and release the button on the 2.4GHz RF remote control Page 9 of 15 Confidential Document Philips Electronics Singapore Pte Ltd Picture 15: The WordPad display 5 for press and release button Digit 5 on 2.4GHz RF remote control. Picture 16: After testing, before shutdown the note book, close all the application software as click the X icon located at upper right hand corner and after that, click the icon Dont Save to abort saving the file. Picture 17: Click the Start icon then select the icon. Page 10 of 15 Confidential Document Philips Electronics Singapore Pte Ltd Picture 18: Click the Shut Down icon Picture 19: Notebook shutting down. Page 11 of 15 Confidential Document Philips Electronics Singapore Pte Ltd 3. Information For Used 2.4GHz RF Remote Control
(RC1974401/01BRF) &
2.4GHz RF USB Receiver (OVU700003/01RF) Page 12 of 15 Confidential Document Philips Electronics Singapore Pte Ltd 3.1 General This remote control is a 2.4GHz RF remote control (RC1974401/01BRF) which will transmit RF protocol. It will work with 2.4GHz RF USB receiver (OVU700003/01RF). 3.2 Stuck key function Stuck key means a key or multiple key has been pressed for a very long time in normal operating mode. ( For multiple key press, refer to section 1.6.4 ) To preserve battery power, the remote will enter sleep mode at about 30 seconds after the last key transition to consume minimal power (the Backlight LED and LED indicator will be turned off at the same time). After all keys are released, the remote resumes normal operation. Following graphic shows when this power down mode is entered: Power Down means the MCU and RF module enters into sleep mode. There is a tolerance of +/- 3 seconds to this timeout STUCK KEY TIMEOUT IR Transmit Keypress Time 30s 3s *
Stuck key mode Key Pressed Code starts transmitting Key still pressed after 30 3 seconds Remote goes in stuck key mode, code transmission stops Remote resumes normal operation after stuck key situation neutralized Code transmission activated by valid key
* Stuck Key Timeout is typical 30 seconds, actual timing depends on the protocol transmitted 3.3 Sleep mode Sleep mode means both application MCU and RF module enter sleep mode. All LEDs/Backlight LED is turned off during sleep mode. Besides remote control can enter sleep mode because of stuck key described in section 3.2, There are 2 conditions where the remote control will enter sleep mode
Upon batteries insertion, remote control will enter sleep mode if there is no key press within 4 secs.
Remote Control enters sleep mode 4 seconds after the key is released In all the 2 cases above, pressing a key again will wakeup the remote control. Page 13 of 15 Confidential Document Philips Electronics Singapore Pte Ltd 3.4 Key press 3.4.1 Continuous key press When the key is press and held, the transmission will repeat at the timing described in 1.1.1.1 If more than 1 key is pressed, there will be no transmission 3.4.2 Multiple Key press Remote control will not react to multiple key press. No transmission will take place. Only the backlight LED will light up. 3.5 Pairing Pairing between remote control and receiver 3.5.1 In order for remote control and receiver to talk to each other, both must have a same ID. There is a 24-bit ID in both the remote control and receiver. This ID is stored in the Eeprom There are 2 scenario when the ID can be written/overwritten:
In the factory, before delivered to customer. 3.5.2 All the receiver and remote control has the same ID, which is default ID ( equivalent to no ID in Eeprom ) . So, when the customer buy the receiver and remote control, they can straight away use it without any setup required. 3.5.3 Pairing by the user Since all the remote control and receiver has the same ID, there could be a scenario where the remote interfere the receiver that is used by other user at the same time. In this case, the user has the option to change this ID on the remote and receiver. This is done by the following receiver.
Make sure the USB receiver is unplugged from the host
Press and hold Clear key and Enter key for 3 seconds. Then release both keys. The remote control now will send a special command code of pairing setup, repeatly for 10 seconds. This command code contains a 24bit- ID ,which is randomly generated by remote control.
Make sure the host is in active mode, plug in the USB receiver now.
When the USB receiver is plugged in, it will enumerates. After enumeration completes, it will look for the command of pairing setup, for 1 second. Page 14 of 15 Confidential Document Philips Electronics Singapore Pte Ltd
If it receives this pairing command, it will overwrite its own 24bit- ID with the new ID in this command.
The USB receiver will acknowledge the successful operation to the remote control.
After the acknowledgement is received by the remote control, it will overwrite its own ID with this ID as well, into the Eeprom. This new ID will remain in the Eeprom of both receiver and remote control.
Now, both remote control and receiver have the same ID and pairing is completed. Page 15 of 15