FCC ID: YG3-SXPCEAN2 WLAN radio board IEEE 802.11 a/b/g/n

User Manual Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification

(installation procedure). Also it will only be installed by professional employees in devices of Phoenix Contact GmbH & Co KG The following information must be indicated on the host device of this module;

[for FCC]

Contains Transmitter Module FCC ID: YG3-SXPCEAN2 or Contains FCC ID: YG3-SXPCEAN2

[for IC]

Contains Transmitter Module IC: 4720B-SXPCEAN2 or Contains IC: 4720B-SXPCEAN2

[for FCC and IC]

This device complies with Part 15 of FCC Rules and Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme la partie 15 des rgles de la FCC et aux normes des CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. The following statements must be described on the user manual of the host device of this module;

[for FCC]

FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

[for IC]

5150-5250MHz and 5250-5350MHz bands are restricted to indoor operations only. La bandes 5150-5250MHz et 5250-5350MHz ont restreints une utilisation lintrieur seulement. High-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Les radars de haute puissance sont dsigns utilisateurs principaux (c.--d., qu'ils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz, et ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.

[for FCC and IC]

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles les radiolectriques (RF) de lignes directrices d'exposition et dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain. la FCC

2018-08-27 USER MANUAL_SXPCEAN2_REV00.DOCX 1 / 4 User Manual 1 Identification This user manual refers to wlan module SX-PCEAN2 with the following certification information:

FCC ID IC-Nr HVIN (Hardware Version Identification Number) FVIN (Firmware Version Identification Number) PMN (Product Marketing Name) YG3-SXPCEAN2 4720B-SXPCEAN2 SX-PCEAN2 1.0.3.0.2 SX-PCEAN2 2 Statement Since this module is not sold to general end users directly, there is no user manual that describes functionality of the module without its implementation into a host system. For the details regarding the stand-alone module, please refer to the specification sheet. This module should be installed in the host device according to the interface specification

(installation procedure). Version: 00 Author: M.Hemp Date: 2018-08-27 2018-08-27 3 Certified Antennas USER MANUAL_SXPCEAN2_REV00.DOCX 2 / 4 Only the following certified antennas may be used with the module:

Antenna Manufacturer Frequency band [GHz]

Gain [dBi]

RAD-ISM-2400-ANT-VAN-3-0-RSMA 2 Phoenix Contact RAD-ISM-2400-ANT-OMNI-2-1-RSMA 2 Phoenix Contact RAD-ISM-2400-ANT-OMNI-6-0 2 Phoenix Contact ANT-OMNI-5900-01 2 Phoenix Contact 2JZ0102 (omnidirectional radiator) 2 2J antennae 2JZ0102 (directional radiator) 2 2J antennae H2B1PC1A1C Unictron Technologies Corporation ANT-OMNI-2459-02 2 Phoenix Contact ANT-DIR-2459-01 1 2 Phoenix Contact 2.4 2.4 2.4 5 2.4 5 2.4 5 2.4 5 2.4 5 2.4 5 3 2.1 6 5 2 2 5 5 1.8 3.9 2.5 5 9 9 Note:

(1) Use of antenna ANT-DIR-2459-01 is only allowed in single chain operation on antenna chain 0!

Note:

(2) All marked antennas must be used on non-DFS channels only!

Version: 00 Author: M.Hemp Date: 2018-08-27 2018-08-27 USER MANUAL_SXPCEAN2_REV00.DOCX 3 / 4 4 Information for implementation 4.1 Information on the host device The following information must be indicated on the host device of this module 4.1.1 For FCC or Contains Transmitter Module FCC ID: YG3-SXPCEAN2 Contains FCC ID: YG3-SXPCEAN2 4.1.2 For IC or Contains Transmitter Module IC: 4720B-SXPCEAN2 Contains IC: 4720B-SXPCEAN2 4.1.3 For FCC and IC The following statements must be described in the user manual of the host device of this module This device complies with Part 15 of FCC Rules and Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme la partie 15 des rgles de la FCC et aux normes des CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'appareil doit accepter tout brouillage subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. If it is difficult to describe this statement on the host product due to the size, please describe in the user manual. Version: 00 Author: M.Hemp Date: 2018-08-27 2018-08-27 USER MANUAL_SXPCEAN2_REV00.DOCX 4 / 4 4.2 Information in the user manual 4.2.1 For FCC FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. 4.2.2 For IC 5150-5250MHz and 5250-5350MHz bands are restricted to indoor operations only. La bandes 5150-5250MHz et 5250-5350MHz ont restreints une utilisation lintrieur seulement. High-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Les radars de haute puissance sont dsigns utilisateurs principaux (c.-

-d., qu'ils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz, et ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. 4.2.3 For FCC and IC This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency

(RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles les radiolectriques (RF) de la FCC lignes directrices d'exposition et dexposition aux frquences radiolectriques (RF) CNR-

102 de lIC. Cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain. Version: 00 Author: M.Hemp Date: 2018-08-27

User Manual Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification

(installation procedure). Also it will only be installed by professional employees in devices of Phoenix Contact GmbH & Co KG Software Version ZXE0326301 is limited to the following antenna:

2JZ0102 The other Software Versions can be used together with following antennas:

The following information must be indicated on the host device of this module;

[for FCC]

Contains Transmitter Module FCC ID: YG3-SXPCEAN2 or Contains FCC ID: YG3-SXPCEAN2

[for IC]

Contains Transmitter Module IC: 4720B-SXPCEAN2 or Contains IC: 4720B-SXPCEAN2

[for FCC and IC]

This device complies with Part 15 of FCC Rules and Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme la partie 15 des rgles de la FCC et aux normes des CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. The following statements must be described on the user manual of the host device of this module;

[for FCC]

FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

[for IC]

5150-5250MHz and 5250-5350MHz bands are restricted to indoor operations only. La bandes 5150-5250MHz et 5250-5350MHz ont restreints une utilisation lintrieur seulement. High-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Les radars de haute puissance sont dsigns utilisateurs principaux (c.--d., qu'ils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz, et ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.

[for FCC and IC]

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles les radiolectriques (RF) de lignes directrices d'exposition et dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain. la FCC

02.02.2021 Federal Communication Commission Equipment Authorization Devision, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 Certification and Engineering Bureau Industry Canada Spectrum Engineering Branch 3701 Carling Avenue, Building 94 Ottawa, Ontario K2H 8S2 C2PC for FCC / C3PC for ISED SX-PCEAN2 FCC ID: YG3-SXPCEAN2 granted on 02.14.2017 and IC: 4720B-SXPCEAN2 granted on 02.14.2017 TO WHOM IT MAY CONCERN Pursuant to CFR 2.1043 and RSP-100, PHOENIX CONTACT GmbH & CO. KG hereby requests a Permissive Change Class II for FCC and Permissive Change Class 3 for ISED. Modifications:

Activation of the following frequencies o 5250-5350; 5470-5725 with DFS Master o The activation of the above-mentioned frequencies was carried out exclusively by software. No changes were made to the hardware. Sincerely, in the Name of PHOENIX CONTACT GmbH & Co. KG, Contact name: Anton Stang Company: Phoenix Testlab GmbH IC Company Number: 3469A Address: Koenigswinkel 10, 32825 Blomberg, Germany

oe a 6 kcxnc PHOENIX TESTLAB GmbH Product Certification Department Koenigswinkel 10 32825 Blomberg, Germany Power of Attorney To Whom It May Concern:

Please be advised that we, Phoenix Contact GmbH & Co. KG, authorize the following persons from PHOENIX TESTLAB GmbH:

e Mr. Kai Heinrichs e Ms. Chvi-Chen Chai e Mr. Uwe Dollitz e Mr. Anton Stang e Mr. Bjrn Michalzik e Mr. Tim Koenig to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters and in-country-testing in the following coutries:

USA, Canada PHOENIX TESTLAB GmbH has our permission to use our technical documents for the approvals for the following name device:

Product description WLAN radio board IEEE 802.11 a/b/g/n |

Brand name PHOENIX CONTACT |

Modelname/-number SX-PCEAN2 |

FCC ID YG3-SXPCEAN2 IC ID 4720B-SXPCEAN2 Unless future correspondence from Phoenix Contact GmbH & Co. KG, please extend your full cooperation to PHOENIX TESTLAB GmbH regarding matters to the above mentioned products to 24 months after the signatory date of this authorization. Contact person Andreas Pape Position in the company Master Specialist Fiber Optics and Wireless Date of signatory 3 March 2020

(signafare of the applicant)

Receiver Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 Certification and Engineering Bureau Innovation, Science and Economic Development Canada Spectrum Engineering Branch 3701 Carling Avenue, Building 94 Ottawa, Ontario K2H 8S2 Modular Approval Statement 08.02.2021 PMN: (Product Marketing Name) FVIN: (Firmware Version Identification Number) SX-PCEAN2 1.0.5.0.1 X X X Subject:

Date:

FCC Certification Number: YG3-SXPCEAN2 Only applicable for ISED certification:

ISED Certification Number: 4720B-

HVIN (Hardware Version Identification Number):

HMN: (Host Marketing Name) SXPCEAN2 SX-PCEAN2 TO WHOM IT MAY CONCERN Pursuant to Annex D in RSP-100 and CFR 15.212, we herewith declare for our module. Modular approval requirement Yes No *

(a) The radio elements must have the radio frequency circuitry shielded. Physical/discrete and tuning capacitors may be located external to the shield, but must be on the module assembly.

*Please provide a detailed explanation if the answer is No.:

(b) The module shall have buffered modulation/data input(s) (if such inputs are provided) to ensure that the module will comply with the requirements set out in the applicable RSS / part 15 under conditions of excessive data rates or over-modulation.

*Please provide a detailed explanation if the answer is No.:

(c) The module shall have its own power supply regulation on the module. This is to ensure that the module will comply with the requirements set out in the applicable standard regardless of the design of the power supplying circuitry in the host device which houses the module.

*Please provide a detailed explanation if the answer is No.:

1

(d) The module shall comply with the provisions for external power amplifiers and antennas detailed in this standard. The equipment certification submission shall contain i) a detailed description of the configuration of highest antenna gain for each type of antenna. ii) the maximum transmitting antenna gain for licence modules iii) a detailed description of the configuration of lowest antenna gain for each type of receiving antenna for Dynamic Frequency Selection (DFS) modules with removable antenna(s)

*Please provide a detailed explanation if the answer is No.:

(e) The module shall be tested for compliance with the applicable standard in a stand-alone configuration, i.e. the module must not be inside another device during testing.

*Please provide a detailed explanation if the answer is No.:

(f) The module shall comply with applicable RSS-102 exposure requirements and any applicable FCC RF exposure requirement which are based on the intended configuration/integration in a host.

*Please provide a detailed explanation if the answer is No.:

Only applicable for FCC certification:

(g) The module must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number.

*Please provide a detailed explanation if the answer is No.:

X X X X X

(h) The modular transmitter complies with all applicable FCC rules. Instructions for maintaining compliance are given in the user instructions. If you have any questions, please feel free to contact us at the address shown below Best Regards, _________________ Anton Stang Phoenix Testlab GmbH Koenigswinkel 10, 32825 Blomberg

+495235-950028 INFO for applicant: LMA may be granted when one or more of the requirements in the table above cannot be demonstrated. LMA will also be issued in those instances where applicants can demonstrate that they will retain control over the final installation of the device, such that compliance of the end product is assured. In such cases, an operating condition on the LMA for the module must state that the module is only approved for use when installed in devices produced by a specific manufacturer. When LMA is sought, the application for equipment certification must specifically state how control of the end product, into which the module will be installed, will be maintained, such that full compliance of the end product is always ensured. 2

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 25.01.2021 TO WHOM IT MAY CONCERN Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we request confidentiality for the following products:

FCC ID YG3-SXPCEAN2 Model name SX-PCEAN2 For the product stated above, we request permanent confidentiality for exhibit which contain Operational Description. The above exhibit contain our trade secrets and proprietary information that could be of benefit to our competitors. If you have any questions, please feel free to contact me at the address shown below. Sincerely, in the Name of PHOENIX CONTACT GmbH & Co. KG, Contact name: Anton Stang Company: Phoenix Testlab GmbH IC Company Number: 3469A Address: Koenigswinkel 10, 32825 Blomberg, Germany Email: stang.anton@phoenix-testlab.de