FCC ID: Y2P-LTE500 Wireless Router

D. Setting Up Your Wireless Devices Your wireless devices (desktop, laptop, iPad, smart-phone, etc.) must be configured to work with your wireless router. Each of these devices must have an internal or external wireless adapter and applicable drivers. User guides for each of these devices should have instructions for wireless set up. You will need the SSID and password you assigned to this wireless router during router setup. For each wireless device, access the setup menu, choose the appropriate SSID from the list of wireless networks, enter your password, and test the wireless connection. Figure 4 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Statement Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be colocated or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 300Mbps Wireless Router Your LTE500 has been pre-configured with an SSID

(wireless network name) and security pass phrase. See the sticker on the bottom of your router for this information. If you wish to change these or other settings, use the following instructions. www.readynetsolutions.com Quick Installation Guide A. Connect the LTE500 Router to Your Computer B. Log In to User Interface 1. To set up your router for the first time, please connect the router to your desktop or laptop computer as shown in the following diagram. Your broadband Internet access will generally be from a service provider modem such as a cablemodem, ADSL modem, or similar device. 2. After the hardware connections have beencompleted, check the status of the LED Indicators using the following table:

LED Indicator Status Description Broadband Internet PC/LAN LTE500 Power Outlet LAN LAN LAN LAN WAN RST DC 12V Please install the wireless antenna on the SMA connector which remark WIFI characters POWER Mode or USB 2.4G Wi-Fi Off Off On (Red) The router is powered on and running normally The router is powered off Flashing (Blue) System is operating or USB device is connected System not operating or USB device is connected On (Blue) Wireless access point is ready Flashing (Blue) Wireless traffic active On (Blue) Port is connected WAN Off Port is disconnected LAN 1-4 Flashing (Blue) Data is transmitting On (Blue) Off Port is connected Port is disconnected Flashing (Blue) Data is transmitting The WAN and LAN Ethernet ports on the router also indicate communication status. Blinking blue indicates the port is connected and data is transmitting. Note: If the LED indicator is not displaying a Normal Status as described in the table at left, please check the associated hardware and connections. Safety Notice The device should be placed on a flat horizontal surface, or secured safely to a wall. Operate equipment away from heat sources. Provide good air ventilation. Keep away from water and damp areas. Disconnect power from the device during severe thunderstorms. Use only the included AC power adapter. Keep router at least 2 feet away from people to reduce exposure to radio frequency emissions. 1. Type http://192.168.12.1 in the Address field of your web browser and press the Enter key. A User Name and Password dialog box will appear. The default User Name is root and the default password is pz938qL500. Enter the user name and password then click the Loginbutton. Note: The default wireless IP address for the wireless router is 192.168.11.1 and the default Subnet Mask is 255.255.255.0 C. Configure Your Wireless SSID and Pass Phrase Figure 1 1. Change SSID To access the Wireless settings, click Network and then Wireless. To change the 2.4GHz band SSID, click EDIT under radio0. Change the ESSID in the Interface Configuration section and click SAVE. We recommend you change security passwords as indicated in Step 2. If you are finished making changes, click APPLY CHANGES to apply your changes. Figure 2 2. Wireless Security Setup Your router is pre-configured with wireless security from the factory. The default wireless Pass Phrase is printed on the sticker on the bottom of the router. If you would like to change the factory-set Pass Phrase, click Wireless Security In the Interface Configuration section of the Wireless tab under Network and enter the new Pass Phrase in the Key field. The Pass Phrase must have at least 8 characters. Click Save. Once a new Phase Phrase has been entered, click Save before going to the next step. Figure 3 IMPORTANT: Click the APPLY CHANGES button at the bottom of the page to apply your changes.

ReaduNet i Model: LTE500 IP Address: 192.168.12.1 Password ID: pz938qL500 CONNECTIVITY SIM Input: 12V-1A User ID: root 2.4GHz SSID: ReadyNet WR1200 2.4GHz Pass Phrase: rnlte500 S/N:

WAN MAC:

IMEI:

FCC ID: Y2P-LTE500

Phonex Broadband Corporation dba ReadyNet Add: 6952 High Tech Drive, Suite B, Midvale, Utah, United States Tel: 801-566-0100 Extension: 104 Fax:801-566-0880 Email: smetcalf@readynetsolutions.com DECLARATION OF SIMILARITY Date: 2020-04-23 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam:

We, Phonex Broadband Corporation dba ReadyNet, hereby declare that the product: Wireless Router, FCC ID:Y2P-LTE500 model:nEX L500 is electrically identical with the model:LTE500 which was tested by BACL with the same electromagnetic emissions and electromagnetic compatibility A description of the differences between those models and that are declared similar are as follows:

They are the same product, and just the different model name, the rest are the same. Please contact me should there be need for any additional clarification or information. characteristics. Best Regards, Signature:

Printed Name: Stephen Metcalf Title:Executive VP

Phonex Broadband Corporation dba ReadyNet Add: 6952 High Tech Drive, Suite B, Midvale, Utah, United States Tel: 801-566-0100 Extension: 104 Fax: 801-566-0880 Email: smetcalf@readynetsolutions.com FCC Authorization Date: 2020-04-23 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern:

We, Phonex Broadband Corporation dba ReadyNet, Hereby authorizes Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratory Corporation on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Clients signature Printed Name: Stephen Metcalf Title: Executive VP QA-FR-170-B

Phonex Broadband Corporation dba ReadyNet Add: 6952 High Tech Drive, Suite B, Midvale, Utah, United States Tel: 801-566-0100 Extension: 104 Fax: 801-566-0880 Email: smetcalf@readynetsolutions.com FCC Confidential Authorization Date: 2020-04-23 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID:Y2P-LTE500 In accordance with Sections 0.457 and 0.459 of the Commissions Rules, Phonex Broadband Corporation dba ReadyNet hereby requests long-term confidential treatment of information accompanying this application as outlined below:

Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature:

Printed Name: Stephen Metcalf Title: Executive VP QA-FR-171-A