WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6686702.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case RED4S_FF Users Manuals RED4S_FF Users Manuals Contents 1 1.1 2 2.1 2.2 2.3 2.4 3 Pin Description .................................................................................................................................. 3 RED4S_FF Pin Description ................................................................................................................. 3 Operation Method .............................................................................................................................. 4 Power Supply ...................................................................................................................................... 4 UART ................................................................................................................................................... 4 RF In/Out ............................................................................................................................................. 4 GUI Control ......................................................................................................................................... 4 Specification ...................................................................................................................................... 8 25 July 2023 2 of 10 1 Pin Description RED4S_FF Users Manuals Figure 1 Pin map of RED4S_FF 1.1 RED4S_FF Pin Description No. Pin Name Description 1,2,6,11,12 GND RXD VCC50 TXD NC VIO CSE 3 4 5 7,10 8 9 GND UART Rx(3.3V) VCC 5.0V : supply power to RED4S_FF UART Tx(3.3V) No connection Supply power to Level shifter IC (3.3V) Chip select enable(3.3V) 25 July 2023 3 of 10 124356789101112 RED4S_FF Users Manuals 2 Operation Method 2.1 Power Supply DC power to operate RED4S_FF is to supply for internal LDO. 2.2 UART The serial interface is assigned with two wires. RS232_TX is for receiving command from host and RS232_RX is for transmitting response to host. Pin connection is shown as below figure. Figure 2 Host MCU Connection 2.3 RF connector RF connector is optimized with 50ohm impedance. Connectors part number is DF11-12DP-2DSA(Hirose co.,LTD) 2.4 GUI Control The RED Utility helps the user to start working with RED DK RFID reader quickly. Follow below steps to run GUI. Windows Start button Program Menu RED Utility_vX.X.X Figure 3 RED Utility_vX.X.X 25 July 2023 4 of 10 TXDxRXDxGNDRED4S_FFHost MCUTXDRXDGND 2.4.1 Mode Change RED Utility provides two view modes. User can select view mode depending on purpose of use between Basic View Mode and Extended View Mode. RED4S_FF Users Manuals To change View Mode, click the extension button marked red in Figure 4 above. Figure 4 Basic View Mode Always use Extended View Mode for measurement. Figure 5 Extended View Mode 25 July 2023 5 of 10 RED4S_FF Users Manuals 2.4.2 RED4S_FF Connection If hardware connection is valid, RED utility connect module REDx automatically. If utility cannot connect hardware, please follow below step Click Connection->Connect to connect to REDx-DK through USB-to-UART at main window GUI will find the Device and synchronize parameters with REDx module automatically. If the GUI cannot find the device automatically, Click Connection->Port Setting and select other Device. Default Baud rate is 115200 bit/s. If the Device connected successfully, status bar will display OPEN state and device number and so on. 2.4.3 Hardware Control Click H/W Control Tab. To control hardware. 2.4.3.1 Band(Region) Setting To select operating band, band setting should be required. Select band in combo box and click Set button to set operating band in group box Frequency Control. 2.4.3.2 Power Class Setting Some countries classify channel number by power class. Click Get button and choose required power class. And then click Set button to set finally. 2.4.3.3 Output Power setting To set RED output power, select the Output Power combo box and click Set button. 2.4.3.4 CW (Continuous Wave) setting It is only used for hardware debugging. To set CW on, click Turn Tx CW on button. To set CW off, click Tx CW off button. 25 July 2023 6 of 10 2.4.4 Tag Inventory Procedure Click Start button in Tag Information Tab to read UHF RFID tag with RED Utility. RED4S_FF Users Manuals Click Start button and Tags EPC information is displayed. 25 July 2023 7 of 10 RED4S_FF Users Manuals 3 Specification No. Item Unit Test Condition Specification Typ. min max Remark 1 2 Frequency Range NOTE1 Tx Max. Power Attenuator NOTE2 Tx Dynamic Range 3 4 Impedance 5 DC Power 6 Operating Temperature 7 Operating Humidity Power Down Idle Active 8 Current Size 9 10 Weight MHz dBm dB dB V C
uA mA mm g 860 13
-20 0 960 27 70 90 20 20 10 14 50 5.0 550 Active current is measured at maximum power with 50ohm load 54.0 x 30 x 9.6 8 NOTE1. Frequency range can be adjusted according to operation region NOTE2. 10dB attenuator applied between antenna and RED4S module. Device Name(Model Name) : RED4S_FF FCC ID: Y3D-RED4SFF Name of Grantee: PHYCHIPS Inc. Production year, month, date:
Manufacturer/Country: Korea 25 July 2023 8 of 10 RED4S_FF Users Manuals FCC Information to User This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:
(1) the device may not cause interference, and
(2) the device must accept any interference, including interference that may cause undesired operation of this device. Caution : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technical for help. End Product Labeling The module is labeled with its own FCC. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following:
Contains FCC ID: Y3D-RED4SFF OEM Responsibilities to comply with FCC The module has been certified for integration into products only by OEM integrators under the following condition:
- The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times.
- The module is limited to installation in mobile or fixed applications.
- The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.
- Separate approval will be required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations other than supplied antennas. As long as the two condition above is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). In the event that these conditions cannot be met, then the FCC authorizations are no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product including this module and obtaining separate FCC authorizations.
- This device is intended only for OEM integrators
- For OEM integration only device cannot be sold to general public. 25 July 2023 9 of 10 RED4S_FF Users Manuals
- Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. This module has to install the input the 5.0V, cause there is a regulator in the device. This device may only operate using an antenna of a type and maximum (or lesser) gain approved by Phychips. Antenna types not included in the list, having a gain grater than the maximum gain indicated for that type, are strictly prohibited for use with this transmitter. Note ANT Peak Gain
-4.47 dBi Part Name KSA-890MS3226A 25 July 2023 10 of 10