FCC ID: 2ANC3PHYCF009 Phyn Smart Water Assistant

Onboarding - Installation Your device is now online. Let's move to the second step -

installing the Phyn device. Connect to Network (2 mins) Installation (20 mins) Congure Your Home (15 mins) 2 3 Continue Prepare for Installation We recommend installing your Phyn device under your kitchen sink or under any sink with hot and cold lines and an outlet not controlled by a switch. You can unplug your Phyn device for these steps. Dont worry, you wont lose your network preferences. Link Button Gather Materials Adjustable Wrench Paper Towels Large Cup or Bucket Pencil or Marker Screwdriver Drill + 11/64 Drill Bit (optional) Included in the box Phyn Device + Sensors (2) Screws (2) Clips (3) 3M Adhesive strip Wall Power Plug Turn Off Water Turn off water under your sink using the angle stops for both the hot and cold lines. Prefer to watch a video?

Mobile 9:41 AM 100%

Mobile 9:41 AM 100%

Mobile 9:41 AM 100%

Mobile 9:41 AM 100%

Mobile 9:41 AM 100%

Mobile 9:41 AM 100%

Mobile 9:41 AM 100%

Mobile 9:41 AM 100%

Mobile 9:41 AM 100%

Mobile 9:41 AM 100%

Mobile 9:41 AM 100%

Mobile 9:41 AM 100%

Mobile 9:41 AM 100%

Mobile 9:41 AM 100%

Mobile 9:41 AM 100%

Mobile 9:41 AM 100%

Mobile 9:41 AM 100%

Mobile 9:41 AM 100%

Mobile 9:41 AM 100%

Mobile 9:41 AM 100%

Installation Help Installation Install Sensors Help Video Tutorial Install Sensors Help Install Sensors Help Install Sensors Help Install Sensors Help Mount Device Help Mount Device Help Mount Device Help Mount Device Help Mount Device Help Mount Device Help Check Installation Help Check Installation Help Check Installation Help Check Installation Help Installation Next Next Next Next Next Next Next My Hot Water is On Done Drain Water Disconnect and Clean Pipes Connect Sensors Turn Water Back On Choose Mount Location Switch Mount to Right Side Mark Mount Location Mount Device Attach Device with Tape Plug in Device and Sensors Turn Hot Water On Turn Water Off Connect each sensor to the pipe. Turn the angle stops back on. Remove the device cover. the mount location through the mounting the cabinet wall. Snap the cover back on. the device is clean and dry. The tape will only Remove the cover from the device and mark Drill pilot holes and then screw the device into Make sure the wall where you want to attach Make sure you are not using water anywhere Plug the device into the outlet. stick once, so make sure to align the device before sticking to the wall. Connect the sensors back to the device. in the house and turn on hot water from the sink where your device is installed. Prefer to Mount on Right Side?

Prefer to Use 3M Adhesive Tape?

Secure cables using mounting clips. Watching for hot water.. Keep water running Checking Installation Installation Successful!

Turn on the hot and cold water at the faucet until water stops owing. If you have a single handle faucet, turn the temperature to half-

hot, half-cold. 1 Unthread the hose connection and catch any remaining water in a cup or bucket. 2 Clean off any pipe tape or sealant and repeat on the other side. 1 2 Tighten once or twice with your wrench, making sure not to overtighten. Next Next Next Find a place on your left cabinet wall where you can reach the reset button on the top of the device and where all the cords will reach. 1 2 3 Let the water run at the faucet until there is no more air in the line. While the faucet is running, check for leaks at the angle stop with a paper towel. If it is leaking, turn the angle stops off again and reconnect the sensors. Next 1 2 3 Unscrew the mounting bracket and place on other side. Make sure the Phyn logo is facing up and the cables are at the bottom. bracket holes. Next 1 2 3 Next For reference only:

indicates molded space for placement inside box FCC Statement folds and is placed in the molded space underneath the 3M Adhesive Strip (98mm x 21mm) FCC statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product has been tested and complies with the specications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna Increase the separation between the equipment and devices Connect the equipment to an outlet other than the receivers Consult a dealer or an experienced radio/TV technician for assistance Radio Frequency 2.4GHz band operation of this product in the USA is rmware-limited to channels 1 through 11. FCC Caution: Any changes or modications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. Innovation, Science and Economic Development Canada Statement: CAN ICES-003(B)/NSM-003(B) Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology. Innovation, Science and Economic Development Canada Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with IC multi-transmitter product procedures. Communiqus relatifs : Innovation, Sciences et Dveloppement conomique Canada CAN ICES-003(B)/NSM-003(B) Le fonctionnement est soumis aux deux conditions suivantes : (1) Cet appareil ne peut causer des interfrences, et (2) il doit accepter toute interfrence, notamment des interfrences qui peuvent provoquer un fonctionnement non dsir de lappareil. Lappareil peut interrompre automatiquement la transmission en cas dabsence dinformations transmettre ou de panne de fonctionnement. Notez que cela na pas pour but dinterdire la transmission dinformations de commande ou de signalisation ou lutilisation de codes rptitifs lorsque la technologie lexige. Communiqus relatifs : Innovation, Sciences et Dveloppement conomique Canada concernant lexposition aux rayonnements Cet quipement est conforme aux limites de lIC sur lexposition aux rayonnements tablies pour un environnement non contrl. Cet quipement doit tre install et utilis une distance minimale de 20 cm entre le radiateur et vous. Cet appareil et ses antennes ne doivent pas tre installs au mme endroit ou fonctionner en association avec une autre antenne ou un autre metteur, sauf conformment aux procdures IC relatives aux multimetteurs. Antenna/Antennal WiFi Internal/Interne Model/Modle RFA-AP821A-70B-84 Gain (dBi) 2.6 CLIENT:

Phyn BRAND:

Phyn PANTONE 2387 U FILE NAME:

Phyn_Packaging_FCC_Insert_mech_v3.ai CREATION DATE:

2019.05.30 FCC STATEMENT INSERT (US/CANADA) PROJECT TYPE:

Packaging CREATION AUTHOR:

SW PRINTER:

NA DIMENSIONS:

77 mm x 84 mm MODIFIED BY:

PRINT METHOD:

FLEXO OFFSET ROTO OTHER 2021/04/28 UPC CODE:

printer to insert. Note that barcodes are shown for position only unless otherwise noted UPC NUMBER:

X 22808 XXXXX X USAGE TERMS:

Unlimited, time and usage is granted globally and for all product, leaves, and avor inclusion illustrations. Usage includes but is not limited to all product, merchandising and company related materials for the stated product for all advertising and media usage. Images can be altered for color and placement renements.

- If digital les supplied do not match supplied PDF, contact the Enlisted Design Production Department.

- For actual color intent, please refer to the current edition of The Pantone Formula Guide for color standards.

- Fonts provided are for output of this artwork only. Production Design Production

xD4 UbLI GAL LL A: al woo'uAYyd@yoA'UdIy : I!W-3 Jeaul6ug joojuDUDew yD, Bul; uDIy : AlLlL Gor PUD SLUIDN ainpoubls L0S06 SE}O4S PE}IUN WO SOUDUO] PAlg oWY jeqsgggl : sseIpPH AUDdWOD s,juDoI\ddy oiuAud : Stupu AUDduwod s,juDoI|ddy AINJOSdsay

{1 |JOJSU] PUD sLONPoId Su asoYoind Asu} so suasN OU} Of SIQISIA SI {| PUD JaxDDIQ Bulpunow apisul ;nd oq |jIM jeqn] au PeUBIsiI@PUN uy OM 1WJB@DUOD ADW }| WOUM OL 6004DAHdEONVE : CI OD4 VL/S/170Z 8404 194421] UOHDDO] [eqn] jo UODID|IDEq LOGOS S8ID}S PEHUN WO SIUDUO] PAG OY [9d SSL O71 uAud

Phyn LLC 1855 Del Amo Blvd, Torrance, CA United States 90501 Confidential Letter Date: 2021/3/25 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID : 2ANC3PHYCFOO9 To Whom It May Concern:

Long Term Confidentiality Pursuant to Sections 0.457 and 0.459 of the Commission's Rules, we hereby respectfully request confidential treatment of information accompanying this application as outlined below:

e@ Block Diagrams e Schematics e@ Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We understand that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Short Term Confidentiality Pursuant to Sections 0.457 and 0.459 of the Commission's Rules, we hereby respectfully request short-term confidential treatment of information accompanying this application as outlined below until 180 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device:

e External Photos e Internal Photos e Test Setup photos e Users Manuals Respectfully, Applicant's company name : Phyn LLC Applicant's company address : 1855 Del Amo Blvd, Torrance, CA United States 90501 ing Yak, Mechanical Engineer Signature Name and Job Title E-Mail : Kian.yak@phyn.com Tel : 877-749-6792 Fax fo:

Phyn LLC 1855 Del Amo Blvd, Torrance, CA United States 90501 Power of Attorney Date: 2021/3/25 Dear Sir,

| hereby have entrusted the following person to be a proxy regarding application for Type Certification. Sporton International Inc. Address : No.8, Lane 724, Bo-ai St., Jnubei City, HsinChu County 302, Taiwan, R.O.C. Name : Leo Huang Job Title : Manager e-mail : Leohvang@sporton.com.tw lam therefore responsible for the contents of the application. FCC ID: 2ANC3PHYCFO09 Respectfully, Applicant's company name > Phyn LLC Applicant's company address : 1855 Del Amo Blvd, Torrance, CA United States 90501

Signature : 7 Z-

Name and Job Title ing Yak, Mechanical Engineer E-Mail Kian.yak@phyn.com Tel : 877-749-6792 Fax z+

Phyn LLC 1855 Del Amo Blvd, Torrance, CA United States 90501 SDoC Attestation Letter Date: 2021/3/25 We Phyn LLC, as the grantee of this project (FCC ID: 2ANC3PHYCF009 / Brand Name: Phyn / Model No.: PHYCFO09), would like to declare that the composite portion has been authorized under the Supplier's Declaration of Conformity procedures (Sporton report No.: FD022708-01, FCC designation number: TW1096). The final product shall consequently comply with the FCC rule applied for SDoC Procedure. Respectfully, Applicant's company name : Phyn Llc Applicant's company address : 1855 Del Amo Blvd, Torrance, CA United States 90501 Signature Name and Job Title : Kia ing Yak, Mechanical Engineer E-Mail : Kian.yak@phyn.com Tel : 877-749-6792 Fax hg