FCC ID: 2ASIVPGA387 Wireless Exit Button

R REV 0.1 ERP PLA3542Q-GL-SMT00030A-V1 ERP P/N:

PLA3542Q/PGA387 STM000,REV.B,160x80mm 80G

, ROHS2.0,REACH,POPs,PAHS,PROP65 K Installation & User Manual is based on bidirectional RF433.92MHz and Lockly 2.0 proprietary encryption, providing communication reliability, stability, and better security. It operates with 2 x CR2032 batteries which last up to 12 months. It is quick and very easy to install and can be mounted anywhere. When using for the first time, please refer to the following steps to install and pair. 1. Press buckle button to remove the backplate cover. 2. 1 2 3 4 2 x CR2032 Batteries Press the button. pairing within 3 minutes after pressing the button or it will exit the pairing mode if no action is taken. If you want to attempt pairing again, please take out and reinsert the batteries, then short press the button to start pairing. Refer to the manual of the smart lock on how to enter pairing mode and ensure pairing is successful before mounting to your desired location. backplate and mount on desired location (near the exit door). You can also use screws to secure the backplate. FCC Warning:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement The Secure Link Wi-Fi Hub complies with FCC radiation exposure limits set forth for an uncontrolled environment. It should be installed and operated with minimum distance 20cm between the radiator & your body. IC WARNING This device contains licence-exempt transmitter(s) that comply with Innovation,Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. IC Radiation Exposure Statement This equipment meets the exemption from the routine evaluation limits in section 2.5 of RSS-102. It should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. Cet quipement est conforme l'exemption des limites d'valuation habituelle de la section 2.5 de la norme RSS-102. Il doit tre install et utilis une distance minimale de 20 cm entre le radiateur et toute partie de votre corps. WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.

Reference No.: WTX22X12255074W001 Page 1 of 8 ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format Specifications: The label shall be securely affixed to a permanently attached part of the device, in a location where it is visible or easily accessible to the user, and shall not be readily detachable. The label shall be sufficiently durable to remain fully legible and intact on the device in all normal conditions of use throughout the devices expected lifetime. Proposed Label Location on EUT FCC ID Label Location Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn

Reference No.: WTX22X01008647W-1 Page 1 of 9 ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format Specifications: The label shall be securely affixed to a permanently attached part of the device, in a location where it is visible or easily accessible to the user, and shall not be readily detachable. The label shall be sufficiently durable to remain fully legible and intact on the device in all normal conditions of use throughout the devices expected lifetime. Proposed Label Location on EUT FCC ID Label Location Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn

PIN GENIE, INC. DBA LOCKLY 676 Transfer Rd., St. Paul, Minnesota 55114, United States Date: 2023-02-28 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements Part 2.911(d) (5) (i) Filing SUBJECT: FCC Application for FCC ID: 2ASIVPGA387 To Whom It May Concern:

PIN GENIE, INC. DBA LOCKLY certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Signatory

[Cindy zhou, COO]

PIN GENIE, INC. DBA LOCKLY 676 Transfer Rd., St. Paul, Minnesota 55114, United States Date: 2023-02-28 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements Part 2.911(d) (5) (ii) Filing SUBJECT: FCC Application for FCC ID: 2ASIVPGA387 To Whom It May Concern:

PIN GENIE, INC. DBA LOCKLY certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely, Signatory

[Cindy zhou, COO]

PIN GENIE, INC. DBA LOCKLY 676 Transfer Rd., St. Paul, Minnesota 55114, United States Date: 2023-02-17 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements Part 2.911(d) (7) Filing SUBJECT: FCC Application for Grantee Code: 2ASIV PIN GENIE, INC. DBA LOCKLY certifies that, as of the date of the filing of the application, we designate ourselves as the U.S. agent for service of process. Designated U.S. Agent Information:

FRN: 0028246908 Name: PIN GENIE, INC. DBA LOCKLY Address: 676 Transfer Rd., St. Paul, Minnesota 55114, United States Contact Person: Cindy zhou Tel.: 4159109522 Email: biz@pin-genie.com Signatory

[Cindy zhou, COO]

Rev 1/26/2023

PIN GENIE, INC. DBA LOCKLY 676 Transfer Rd., St. Paul, Minnesota 55114, United States Date: 2023-02-28 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 FCC Class II Permissive Change Application Letter To Whom It May Concern:

This is to request a Class II permissive change, the following the original equipment:

Product name : Wireless Exit Button FCC ID:

2ASIVPGA387 Date of Grant:

05/11/2022 Model No.:

PGA387 Change Contents: update the components on main board as below (The part to be added is MOS.):

Location Old PCB of FCC ID: 2ASIVPGA387 New PCB of FCC ID: 2ASIVPGA387 MOS

MOS tubes are added to the main board to optimize the PCB layout;

The circuit changes have no effect on the radio parameters. Modifications that do not change the fundamental RF characteristics and that do not degrade the unwanted emissions of the certified product, please refer to test report for more details;

Modifications that do not change physical characteristics significantly. We attach new photographs to identify the modified product. Sincerely, Signatory

[Cindy zhou, COO]

PIN GENIE, INC. DBA LOCKLY 676 Transfer Rd., St. Paul, Minnesota 55114, United States Date: 2023-02-28 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 SUBJECT: FCC Application for FCC ID: 2ASIVPGA387 Confidentiality Request To whom it may concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. Block Diagram Operational Description Schematics Parts List Tune-Up Information Security Information Software Defined Radio (SDR) Information The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Internal Photos Test Setup Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. or For 180 days pursuant to KDB 726920 D01. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Signatory

[Cindy zhou, COO]

PIN GENIE, INC. DBA LOCKLY 676 Transfer Rd., St. Paul, Minnesota 55114, United States Date: 2023-02-28 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 SUBJECT: FCC Application for FCC ID: 2ASIVPGA387 To Whom It May Concern:

I, the undersigned, hereby states this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules, and will apply the Supplier's Declaration of Conformity procedure to the class B device. I understand the following FCC requirements:

1. Devices subject to the SDoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-to-government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage:

https://apps.fcc.gov/oetcf/eas/reports/TestFirmSearch.cfm

(Select the

"accredited" option to search for FCC recognized accredited test firms.) 2. Pt 2.1077 contains the list of information that must be included in the Supplier's Declaration of Conformity, which must be supplied with each product sold. The SDoC compliance info shall be included in the Users Manual or as a separate sheet. The info must contain the name, address, and phone number of the responsible party, which must be located within the United States. According to 2.909(b), the responsible party is either the Manufacturer or if the product is imported the Importer. Sincerely, Signatory

[Cindy zhou, COO]

PIN GENIE, INC. DBA LOCKLY 676 Transfer Rd., St. Paul, Minnesota 55114, United States Date: 2023-02-28 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 SUBJECT: FCC Application for FCC ID: 2ASIVPGA387 POWER OF ATTORNEY To Whom It May Concern:

We, the undersigned, hereby authorize Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, PIN GENIE, INC. DBA LOCKLY are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Signatory

[Cindy zhou, COO]

PIN GENIE, INC. DBA LOCKLY 676 Transfer Rd., St. Paul, MN 55114, United States

(FCC ID2ASIVPGA387) POWER OF ATTORNEY DATE: 2022-05-06 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern:

We, the undersigned, hereby authorize Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, PIN GENIE, INC. DBA LOCKLY are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, PIN GENIE, INC. DBA LOCKLY

(Cindy zhou)

(COO)