FCC ID: 2ARLM-CST-2A 2.4G REMOTE CONTROL

Introduction This controller is used for electric kids cars, including a remote control and a controller (for receiving).It uses 2.4G wireless remote control. The controller controls two motors to rotate. The remote control uses 3V battery to supply power. The receiver uses 12V battery to supply power. Product ship with no battery. 1

Use a screwdriver to remove the battery cover of the remote control, insert two AAA 1.5V dry batteries in correct polarity. Close the battery cover and x it with the screw. (Battery replacement also according to the above steps) 1.All batteries should be inserted in the correct polarity. 2.Non-rechargeable battery cannot be recharged 3.Take out and properly deal with the dead battery. To avoid injury, please keep kids away from the battery. 4.The direct contact between the positive and negative terminals may result in re or explosion. Avoid direct connect between the terminals. 5.Do not mix old and new batteries. DO not mix alkaline, standard(carbon-

zinc),or rechargeable(nickel-cadmium) batteries. 6.Only an adult who has read and understood the safety warnings can recharge the battery. Instructions:

Connect the controller to the electric kids car with wire and turn on the car and controller at the same time. Coding the controller and receiver when control with the remote controller. When the remote controller rst turns on, the top light ashes slowly and then turns on the receiver. When the light long bright, it means coding nishes and you can turn on the car. There are 6 buttons on the remote controller:forward, backward, left, right, Speed Conversion , stop. The power button is used as the power supply when the remote controller is stand-by. When the remote control is working. 2.Matching the frequency of car and remote control 1. Turn o the Power Switch on the car. 2. Remove the battery cover on the Remote Control and put in 2 AAA battery, the three LED indicators will ash. 3. Turn on the Power Switch on the car, when the LED indicators stop ashing and 2 of them are on, matching successes. 4. Once the matching is made, there is no need to match code again only if the battery is replaced. 5. The Remote Control will enter a sleep mode if not used for a long time and the LED indicators will be o. Press any buttons to wake up the Remote Control, and it can be used normally. Button Description: : forward : reverse : turn left : turn right S: Speed stop: emergency brake, press it and the running function will fail, press again, it release. LED Indicator stop Remote control operating instruction Remote control is priority (when the car is in Remote control, the remote control personnel can control the car forward and backward, high/Low speed, steering and other functions, the driver CAN NOT operate the car). Press the forward button, the car goes forward. Press reverse button, the car goes reverse. Press the stop button to brake the car urgently. Press stop button again to release the brake system. Press the turn left button, car turn left, Press the turn right button, car turn right, The S button is speed button, one light on is low speed, two lights on for intermediate speed, three lights on for high speed. NOTICE Battery Warnings The batteries are not included. Always insert batteries correctly with regards to polarity (+ and-) marked on the battery and the product. Exhausted batteries should be immediately removed from product and properly disposed. replacement of a battery with an incorrect type that can defeat a safeguard

(for example, in the case of some lithium battery types);

- disposal of a battery into re or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;

- leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of ammable liquid or gas; and

- a battery subjected to extremely low air pressure that may result in an explosion or the leakage of ammable liquid or gas This product and - if applicable - the supplied accessories too are marked with

"CE" and comply therefore with the applicable harmonized European standards listed under the RE Directive 2014/53/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see:

www.recyclethis.info 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specic battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead

(Pb), or mercury

(Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see:www.recyclethis.info FCC Warning:

Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference,and

(2) this device must accept any interference received, including interference that may cause undesired operation.

1.Turn off the Power Switch on the car. 2.Remove the battery cover on the Remote Control and put in 2 AAA battery, the three LED indicators will flash. 3.Turn on the Power Switch on the car, when the LED indicators stop flashing and 2 of them are on, matching successes. 4.Once the matching is made, there is no need to match code again only if the battery is replaced. 5.The Remote Control will enter a sleep mode if not used for a long time and the LED indicators will be off.Press any buttons to wake up the Remote Control, and it can be used normally. FCC ID: 2ARLM-CST-2A Trade name: 2.4G REMOTE CONTROL Model Number: CST-2A This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 001 , Ogh a ae rey ) OSE

ena ee oan S ae ON ae APPUGCGI Veviaraum:, United States Applicant Legal Business Name Pinghu City Cang Sheng Plastic Factory group 22, zhonghua village, xincang town,pinghu city, Zhejiang Province, 314200 China 2ARLM ronrr NAD ae OCT OVA lad PUN EAVEM ND EM ntand Corin Na Contact Email phzhengbiao@163.com Contact Phone 13906733836 _ a a

|, the undersigned, certify that | am an authorized signatory for the Applicant and therefore declare;

a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the bes! of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

(1) labeling the equipment with the exact FCC ID as specified in this application,

(2) compliance statement labeling pursuant to the applicable tules,

(3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. ea) in accordance with |[$017065. FCC KDB641163. FCC KDB610077. KDB394321 and RSP-100. the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements ;

74\ the Annheant tmnderefand arrcents and agrees thal a camnile may he requected for surveillance testing. ive) Pree ee Cie ee ne ee ee ee le ON ge aR Oe pees ern wm ree ote

(2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED.

(3) the Applicant shall, upon request by SGS, at the Applicant's expense, provide a production sample of the requested product to SGS, CCR endinc (COM ac inctnirtad The camnie chall jnchido all criminal devirec cahlec cofhwarm arreccennec or other harrhwore or FRO ee Gener are DR ee ee ee ee ES eee eee eee eee eee ee ee eee Le ee Le Oe eee hea software required for evaluation, review, certification and audit surveillance of products certified by y SGS. sa a Ra ee 5 ae Sr ta sk a a a a a a eR i i A i a an il a a ie a ma Pi A ees ED FURR ES Pe Ue EY Ey, ES perme Br aang Oe ae OIE ee ee eee ee, eee ne ee eS ee te 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to RSP-100:

gi eA Applicant Declaration ASV

Pinghu City Cana Sheng Plastic Factory Date: 04/12/2021 TO: Federal Communication Commission ene Ake a Ne ea te CAYVIPTNET AULDOMZavOnN Drancn 7435 Oakland Mills Road Columbia MIN 24n4ce

| a | ee, Ce Regarding: FCC ID: JART M-CST.IA es ts ~~ eS ee a ea. ee a eee Cerca ae To whom it may concern:

We, the undersigned, hereby authorize Parlam Zhan to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing OF ail documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have lh ee: cal tdi ain ce i eS oe ak, ee, te i ee ee MIN OG Viet Gv Gwe VI YM Wit. We the undersigned. hereby certify that we are not subiect to a denial of federal benefits. that includes oe OO oe nal So ee ey ee en Re FCC benefits, pursuant to Section 5301 of the Anti- -Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, | acknowledge that all responsibility for complying ' with the terms and conditions for Certification, as specified by SGS North America, Inc., stil!

Nar ee | ee ee ae Pesides WIN FINQnNU Uy VAllg GHEY Fiadsue Factory oe i Ww &

This authorization js valid anut rther written notice from the applicant. Name (Ppnted): Cheng ee / Tite: Engineer Signatur On behalf of Company: Pinghu City Cang Sheng Plastic Factory Telephone: 13906733836

Dinnhis City Cann Chann Diactic Factary CP ee Se ee RD og eee, ces re To: SGS North America Inc 620 Old Peachtree Road SUITE 100 Suwanee, Georgia ete! ae eo ne MITE Vlales From: Pinghi City Cang Sheno Plastic Factory ON EN Senge Nt PEL LS ee NR? = OO. ares es! aR ONES ea Oe group 22, zhonghua village, xincang town, pinghu city, Zhejiang Province, 314200 China es ee ee oe uP Regarding: Confidentiality Request regarding application for FCC ID: ZAKRLM-Go I-42 LONG TERM CONFIDENTIALITY ee es cee i pe ees ce ee ee ee ees ee See a ON EN eT FUrsualt tO Sf UPI SECUON U4 07 de Ot Oe Cree ee) ee ee confidential treatment of the documents listed below, associated with the certification application reterancad ahnvao eS ES Saar SS as Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this TntaArmahnAnm mau area haresfiil tea tha hiieinaece Af tha anntizrant ea oe ee ee ee IS | Se ee Ce SET Oe ne eT eee Sincerely, [SX SA il Sagal she Signature: \ a ~ 7

. Printed NameNe file with the FQC associated with the Grantee Code): Zheng Biao Title: Senior Certification E er Company Name: Pinghu City Cang Sheng Plastic Factory