DIGITAL MEDIA RECEIVER E n g l i s h MVH-S21BT Owner's Manual Contents Before You Start .................................................................................. 2 Basic Operation .................................................................................. 3 Detaching the front panel .............................................................. 3 Connections ........................................................................................ 3 Specifications ...................................................................................... 4 Before You Start Thank you for purchasing this PIONEER product. To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe WARNINGs and CAUTIONs in this manual. Please keep the manual in a safe and accessible place for future reference. WARNING Do not attempt to install or service this product by yourself. Installation or servicing of this product by persons without training and experience in electronic equipment and automotive accessories may be dangerous and could expose you to the risk of electric shock, injury or other hazards. Do not attempt to operate the unit while driving. Make sure to pull off the road and park your vehicle in a safe location before attempting to use the controls on the device. CAUTION Do not allow this unit to come into contact with moisture and/or liquids. Electrical shock could result. Also, damage to this unit, smoke, and overheating could result from contact with liquids. Always keep the volume low enough to hear outside sounds. This product is evaluated in moderate and tropical climate condition under the Audio, video and similar electronic apparatus - Safety requirements, IEC 60065. If you experience problems Should this unit fail to work properly, please contact your dealer or nearest authorized PIONEER Service Station. 2 En Basic Operation M.C. (multi-control) dial SRC/OFF DISP/DISP OFF Detaching the front panel Detach the front panel to prevent theft. Remove any cables and devices attached to the front panel and turn off the unit before detaching it. Detach Attach Hook Button BAND/DIMMER Display window Detach button Connections Frequently used operations Purpose Operation Turn on the power When ignition on or system recovery, the unit power on automatically. Adjust the volume Turn the M.C. dial. Select a source Change the display information Return to the previous display/list Press SRC/OFF repeatedly. Press DISP repeatedly. Press BAND/DIMMER
. Return to the normal display from the menu Press BAND/DIMMER Answering/ending a call Press
. 1. Rear line output 2. Antenna input 3. Power cord input 4. Fuse (10A) En 3 Specifications General Power source:
14.4 V DC (10.8 V to 15.1 V allowable) Negative ground Maximum current consumption:
10.0 A Dimensions (W H D):
DIN Chassis: 178 mm 50 mm 97 mm Nose: 188 mm 58 mm 17 mm D Chassis: 178 mm 50 mm 97 mm Nose: 170 mm 46 mm 17 mm Weight:
0.5 kg Audio Maximum power output:
49 W 4 ch/4 Continuous power output:
22W 4 (50 Hz to 15 000 Hz, 5 % THD, 4 load, both channels driven) Load impedance:
4 (4 to 8 allowable) USB USBstandard specification:
USB 2.0 full speed Maximum current supply:
500 mA USB Protocol:
MSC (Mass Storage Class) AOA (Android Open Accessory) 2.0 File system: FAT12, FAT16, FAT32 4 En FM tuner Frequency range:
87.5 MHz to 108.0 MHz Usable sensitivity:
11 dBf (1.0 V/75 , mono, S/N: 30 dB) Signal-to-noise ratio:
72 dB (IEC-A network) AM tuner Frequency range:
531 kHz to 1 602 kHz (9 kHz) 530 kHz to 1 640 kHz (10 kHz) Usable sensitivity:
25 V (S/N: 20 dB) Signal-to-noise ratio:
58 dB (IEC-A network) Bluetooth Version: Bluetooth 3.0 + EDR Output power:
+4 dBm Maximum (Power class 2) Frequency band(s):
2 402 MHz to 2 480 MHz Bluetooth profiles:
GAP (Generic Access Profile) 1.1 SDAP (Service Discovery Application Profile) 1.1 HFP (Hands Free Profile) 1.6 A2DP (Advanced Audio Distribution Profile) 1.2 Specifications and the design are subject to modifications without notice. Appendix FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequencies and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. IC STATEMENT This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son fonctionnement est soumis aux deux conditions suivantes :
( 1 ) Ce dispositif ne peut causer d'interfrences ; et
( 2 ) Ce dispositif doit accepter toute interfrence , y compris les interfrences qui peuvent causer un mauvais fonctionnement de l'appareil. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the unit & your body. 5 En http://global.pioneer/en/info/globalnetwork/
http://www.pioneer-mea.com PIONEER CORPORATION 28-8, Honkomagome 2-chome, Bunkyo-ku, Tokyo 113-0021, JAPAN PIONEER ELECTRONICS(USA)INC. P.O. Box 1540, Long Beach, California 90801-1540,U.S.A. TEL:(800) 421-1404 PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique TEL:(0)3/570.05.11 PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 2 Jalan Kilang Barat, #07-01, Singapore 159346 TEL: 65-6378-7888 PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 5 Arco Lane, Heatherton, Victoria, 3202 Australia TEL:(03) 9586-6300 PIONEER ELECTRONICS DE MXICO S.A. DE C.V. Blvd. Manuel vila Camacho 138, 10 piso Col.Lomas de Chapultepec, Mxico, D.F. 11000 TEL: 52-55-9178-4270, FAX: 52-55-5202-3714 407 8 886-(0)2-2657-3588
( ) 909 5 852-2848-6488 2018. P/N:127075000XXXX