FCC COMPLIANCE NOTICE Any changes or modications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. 2019 Plasma Cloud Ltd. All Rights reserved 5/F Yat Chau Building, 262 Des Voeux Road Central, Hong Kong www.plasma-cloud.com The software included in this product contains copyrighted software that is licensed under GPL. A copy of that license, along with instructions on how to obtain the source code, is available at https://www.gnu.org/copyleft/gpl.html IC COMPLIANCE NOTICE This product meets the applicable Innovation, Science and Economic Development Canada technical specications. Ce produit rpond aux spcications techniques applicables l'innovation, Science et Dvelop-
pement conomique Canada. This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:
(1)
(2) This device may not cause interference; and This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1)
(2) L'appareil ne doit pas produire de brouillage, et L'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. CE COMPLIANCE NOTICE This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. BE BG CZ DK DE EE IE EL ES FR HR IT CY LV LT LU AT PL PT RO SI SK FI SE UK MT HU NL This device complies with the ISED radiation exposure limit set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet quipement est conforme avec l'exposition aux radiations ISED dnies pour un environne-
ment non contrl. Cet quipement doit tre install et utilis une distance minimum de 20 cm entre le radiateur et votre corps. Cet metteur ne doit pas tre co-localises ou oprant en conjonction avec une autre antenne ou transmetteur. Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated. Avertissement:
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur an de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
(ii) lorsquil y a lieu, les types dantennes (sil y en a plusieurs), les numros de modle de lantenne et les pires angles dinclinaison ncessaires pour rester conforme lexigence de la p.i.r.e. applicable au masque dlvation, nonce la section 6.2.2.3, doivent tre clairement indiqus. PA 2 2 0 0 Q u i c k S t a r t G u i d e INTRODUCTION Thank you for purchasing the PA2200. This Quick Start Guide is designed to guide you through the installation process. PACKAGE CONTENTS 1. Access Point 2. Mounting options (ceiling, wall, T-rail) 3. Screws and screw plugs for various surfaces 4. Cable tie CLOUD MANAGEMENT Sign up at console.plasma-cloud.com. 1. 2. Create your rst organisation by navigating to Organ-
isations Create new organisation. Fill in the form and click Create. 3. You can now create your rst network. Navigate to Networks Create new network, ll in the form and click Create. 4. Setup your network by navigating to Settings Network. 5. Create and congure your rst SSID by navigating to Settings SSIDs Create new SSID. 6. Go back to Overview and click on the map to add your rst Access Point. The last point can be repeated to add as many Access Points as needed. You can now plug-in your Access Point and connect it to the Internet. The Plasma Cloud conguration only takes a few seconds!
PHYSICAL INSTALLATION This Access Point is designed to be installed indoor only and can operate between 0C ~ 40C (32F ~ 104F). It comes with a set of mounting options that can be used to install this device on various surfaces such as: ceilings, walls and T-rails of various sizes. This Access Point can be powered by:
1. a 54V/0.5A PoE injector (802.3af/at) 2. a 12/2A DC power adapter 1 2 SUPPORT Feel free to visit https://support.plasma-cloud.com for additional technical guidance or to contact our support department. T-RAIL MOUNTING 1 Slide the T-rail mount into the slot of the Access Point. WALL MOUNTING 1 Use the provided screws and screw plugs to x the mount-
ing plate on the wall. 2 3 Hook the stationary end of the mount bracket to the T-rail. Your Access Point is now safely clipped to the T-rail. 2 3 Slide the Access Point over the mounting plate. Your Access Point is now safely attached to the wall. 2.4GHz5GHz15GHz22.4GHz5GHz15GHz22.4GHz5GHz15GHz2