FCC ID: 2AJGMUV82 GMRS Two-way radio

USERS MANUAL Model: UV-82 ______________________________ PREFACE Thank you for purchasing UV82 GMRS Radio, which is a dual band/dual display radio/dual watch. This easy-to-use radio will deliver you secure, instant and reliable communications at peak efficiency. Please read this manual carefully before use. The information presented herein will help you to derive maximum performance from your radio. This manual is applicable to the following product: UV82IC, 82-UV Radios. Table of Contents 1. GETTING STARTED 1.1 Regulations and Safety Warnings 1.2 Main features 1.3 Maintenance 1.4 Programming software (optional) 1.5 Content of the packaging 2. BATTERY INFORMATION 2.1 Charging the Battery Pack 2.2 Charger Supplied 2.3 Use Caution with the Li-ion Battery 2.4 How to Charge 2.5 LED Indicator 2.6 How to Store the Battery 3. INSTALLATION OF ACCESSORIES 3.1 Installing / Removing the Antenna 3.2 Installing the belt clip 3.3 Installing the battery pack 3.4 Additional Speaker/Microphone (Optional) 4. RADIO OVERVIEW 4.1 Buttons and controls of the radio 4.2 Main controls and parts of the radio 4.3 Status Indications 4.4 Main keypad controls 5. BASIC OPERATIONS 5.1 Power on the radio 5.2 Adjusting the volume 5.3 Making a call 5.4 Channel selection 5.5 Frequency (VFO) mode 5.6 Channel (MR) mode 6. ADVANCED FEATURES 6.1 Frequency scanning 6.2 Channel scanning 6.3 Search CTCSS/DCS Code 6.4 CursorConversion (A/B) 6.5 High/low power fast selection 6.6 Keypad lock 6.7 FM Radio (FM) 6.8 Flashlight 6.9 1000Hz, 1450Hz, 1750Hz Tone-burst 6.10 Manual Programming (Channels Memory) 6.11 Repeaters Programming 7. WORKING THE MENU SYSTEM 7.1 Basic use 7.2 Using short-cuts 7.3 Functions and operations

(1) Squelch level (SQL) - MENU No.0

(2) Step frequency (STEP) - MENU No.1

(3) Output power (TXP) - MENU No.2

(4) Battery save (SAVE) - MENU No.3

(5) VOX Function (VOX) - MENU No.4

(6) Wide/Narrow bandwidth (WN) - MENU No.5

(7) Backlight (ABR) - MENU No. 6

(8) Dual Watch Operation (TDR) - MENU No. 7

(9) Keypad beep (BEEP) - MENU No. 8

(10) Time-Out-Timer (TOT) - MENU No.9

(11) Receiving DCS (R-DCS) - MENU No.10

(12) Receiving CTCSS (R-CTCSS) - MENU No.11

(13) Transmitting DCS - (T-DCS) - MENU No.12

(14) Transmitting CTCSS (T-CTCSS) - MENU No.13

(15) Voice function (VOICE) - MENU No. 14

(16) ANI-ID (ANI-ID) - MENU No.15

(17) DTMFST (DTMFST) - MENU No.16

(18) Signal code (S-CODE) - MENU No.17

(19) SCAN Resume Mode (SC-REV) - MENU No.18

(20) PTT-ID (PTT-ID) - MENU No.19

(21) PTT ID delay (PTT-LT) - MENU No.20

(22) Channel A Display Mode (MDF-A) - MENU No.21

(23) Channel B Display Mode (MDF-B) - MENU No.22

(24) Busy Channel Lock (BCL) - MENU No. 23

(25) Auto Keypad Lock (AUTOLK) - MENU No.24

(26) Frequency offset direction (SFT-D) - MENU No.25

(27) Frequency offset (OFFSET) - MENU No. 26

(28) Channel store - (MEM-CH) - MENU No. 27

(29) Channel Delete (DEL-CH) - MENU No.28

(30) Standby backlight (WT-LED) - MENU No.29

(31) RX backlight (RX-LED) - MENU No. 30

(32) TX backlight (TX-LED) - MENU No.31

(33) Alarm Mode (AL-MOD) - MENU No.32

(34) Dual Watch (TDR-AB) - Menu No.34

(35) Side tone elimination (STE) - Menu No. 35

(36) Side tone elimination in communication through repeater (RP-STE) - Menu No. 36

(37) Delay time of side tone elimination in communication through repeater (RPT-RL) - Menu No.37

(38) Display mode at the turning on (PONMSG) Menu No.38

(39) Roger beep (ROGER) - Menu No. 39

(40) Reset (RESET) - Menu No.40

(41) Repeater Tone (R-TONE) - Menu No.41 8. ON-LINE SERVICE AND SUPPORT Appendix A. Trouble shooting guide Appendix B. - Technical Specifications Appendix D. - GMRS Frequency Chart (MHz) Appendix D. - Weather Channel Assignments Appendix C. - Shortcut Menu operations 1. GETTING STARTED 1.1 Regulations and Safety Warnings ATTENTION!

To help you ward off bodily injury or property loss that may arise from improper operation, please read all the information carefully before using our products. This contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulation. FCC Statement cause harmful interference. This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not This equipment generates and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Verification of harmful interference by this equipment to radio or television reception can be determined by turning it off and then on. The user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The device has been tested against the SAR limit (1.6W/kg). The highest SAR value reported under this standard during product certification for use at the Face up is 0.955 W/kg and when properly worn on the body is 1.559 W/kg. This device was tested for typical operations. The device only supports simplex-mode and transmitting is no more than the rated duty cycle factor of 50% of the time. For hand-held operation, the radio should be held at least 25mm from the user's face. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with RF exposure requirements, and should be avoided. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBIITED UNDER FCC RULES AND FEDERRAL LAW. IMPORTANT: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. Your radio is set up to transmit a regulated signal on an assigned frequency. It is against the law to alter or adjust the settings inside the radio to exceed those limitations. Any adjustments to your radio must be made by qualified technicians. To be safe and sure:

Never open your radios case. Never change or replace anything in your radio except the battery. Any attempt to change frequencies or output power of the radio invalidates the approval Compliance with RF Exposure Standards The radio complies with the following RF energy exposure standards and guidelines:

United States Federal Communications Commission, Code of Federal Regulations; 47 CFR 1.1307, 1.1310 and 2.1093 American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005; Canada RSS102 Issue 5 March 2015 Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 Edition RF Exposure Compliance and Control Guidelines and Operating Instructions exposure limits, always adhere to the following procedures. Guidelines:

Do not remove the RF Exposure Label from the device. To control your exposure and ensure compliance with the general population/uncontrolled environmental User awareness instructions should accompany device when transferred to other users. Do not use this device if the operational requirements described herein are not met. Operating Instructions:

Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), press the Push-to-Talk (PTT) key. To receive calls, release the [PTT] key. Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy only when transmitting (in terms of measuring for standards compliance). Keep the radio unit at least 2.5cm away from the face. Keeping the radio at the proper distance is important as RF exposure decreases with distance from the antenna. The antenna should be kept away from the face and When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of the correct clip for this product. Use of non-approved accessories may result in exposure levels which exceed the FCC's occupational/ controlled environmental RF exposure limits. Use of non-approved antennas, batteries, and accessories causes the radio to exceed the FCC RF exposure eyes. guidelines. Contact your local dealer for the product's optional accessories. GMRS Communication This GMRS (General Mobile Radio Service) feature is a land-mobile service available for short-distance, two-way communications in the USA. You must have a valid FCC license to communicate on these channels. The GMRS frequencies that radio this radio uses are set aside for communicating with others while hiking, biking, and working; keeping track of family and friends at a crowded public event; checking with travel companions in another car; talking with neighbors; arranging meeting spots with others while shopping at the mall. Licensed users will be issued a call sign by the FCC, which should be used for station identification when operating this radio. GMRS users should also cooperate by engaging in permissible transmissions only, avoiding channel interference with other GMRS users, and being prudent with the length of their transmission time. Licensing Information USA This two-way radio operates on GMRS (General Mobile Radio Service) frequencies which require an FCC (Federal Communications Commission) license. A user must be licensed prior to transmitting on the GMRS band with this radio. Serious penalties could result for unlicensed use of GMRS channels, in violation of FCC rules. Operation of this radio is subject to additional rules specified in 47 C.F.R. Part 95. For licensing information and application forms, please call the FCC Hotline at 800418-FORM. Request form #159 and from #605. Questions regarding the license application should be directed to the FCC at 888-CALL-FCC. Additional information is available on the FCCs website at www.fcc.gov. NOTE: Even if you operate this radio on GMRS8-14th channels at low power (0.5 watt), you are required to have an FCC license. Because this radio operates in the 0.5 to 5 watt GMRS power range all GMRS rules apply and will require you have a GMRS license even for GMRS communication. Normal GMRS only radios operate 8-14th at a maximum power of 0.5 watt power and have an integral (non-detachable) antenna. Initial setup Safety Information The following safety precautions should always be observed during operation, service and repair of this equipment. Qualified technicians shall service this equipment only. Do not modify the radio for any reason. Only use the company supplied or approved batteries and chargers. Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result. Turn off your radio prior to entering any area with explosive and flammable materials. Do not charge your battery in a location with explosive and flammable materials. To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any area where Turn off your radio before boarding an aircraft; any use of a radio must be in accordance with airline regulations posted notices instruct you to do so. or crew instructions. Turn off your radio before entering a blasting area. 1.2 Main features For vehicles with an air bag, do not place a radio in the area over an air bag or in the air bag deployment area. Dual band (VHF/UHF) displayed Operating modes: UHF/VHF, UHF/UHF, VHF/VHF 22 Modifiable GMRS Two-Way Channels (RX &TX) 8 Modifiable GMRS Repeater Channels (RX & TX) 87 Programmable Scanner Channels (Receive Only) 11 NOAA Weather Radio & Scan (Channels 117-127) Output power: 4W/0.5W (GMRS) CTCSS and DCS codes research 155 Privacy Codes (50 CTCSS codes/ 105 DCS codes) 1750Hz tone for repeaters SOS Emergency function Tri-Color Adjustable Backlight Built-in FM Radio (88-108MHz) Scan, Dual Watch functions Channel or frequency mode selection 2pin Kenwood accessory jack TOT (Time out timer) Reverse function DTMF function Setting and storing of channel names Busy Channel Lockout function (BCL) VOICE: vocal indication of the function selected Frequency step: 2.5/5/6.25/10/12.5/25KHz Frequency offset (adjustable): 0-69.990MHz Squelch adjustable in 9 levels Li-Ion 1800mAh battery pack Repeater shift Power Save 1.3 Maintenance Your Two Way Radio is an electronic product of exact design and should be treated with care. The suggestions below will help you to fulfill any warranty obligations and to enjoy this product for many years. Do not attempt to open the radio for any reason! The radios precision mechanics and electronics require experience and specialized equipment; for the same reason, the radio should under no circumstances be realigned as it has already been calibrated for maximum performance. Unauthorized opening of the transceiver will void the warranty. Do not store the Radio under the sunshine or in hot areas. High temperatures can shorten the life of electronic devices, and warp or melt certain plastics. Do not store the radio in dusty and dirty areas. Keep the Radio dry. Rainwater or damp will corrode electronic circuits. If it appears that the Radio diffuses peculiar smell or smoke, please shut off its power immediately and take off the charger or battery from the radio. 1.4 Programming software (optional) WARNINGYou may be tempted to use FRS, GMRS, MURS (in the USA) or PMR446 (in Europe) frequencies. Do note however that there are restrictions on these bands that make this transceiver illegal for Thanks to Pofung Programming software PRG-UV82, it is possible to increase the performance of your radio or to reduce its functionality by enabling or disabling some features (CTCSS, TOT, VOX, ROGER BEEP, SQUELCH, VOICE...) your programming must comply with your FCC (or other country) license certification. Any attempt to change frequencies or output power of the radio invalidates the approval. Pofung UV82 radios ship from the manufacturer Keypad locked per FCC rules. You will need the programming cable to connect your radio to your computer for programming. The programming software are available for download from Pofung website: http://www.pofungshop.com. When programming this radio for the first time, it is recommended you first READ the radio with the software and then save this file for future reference as it contains the default programming and settings. In addition, after you READ this radio with software, first make your programming and frequency changes, then send this edited file back to your radio. GMRS channels are setup in the standardized GMRS flow. Channels 1-22 are non-repeater channels coordinating with the GMRS channel list and channels 23-30 are GMRS repeater channels. Channel List:

22 Modifiable GMRS Two-Way Channels (Channels 1-22) - Receive and Transmit 8 Modifiable GMRS Repeater Channels (Channels 23-30) - Receive and Transmit 11 Fixed NOAA Weather Channels (Channels 117-127) -Receive Only 87 Programmable Scanner Channels (Channels 00 & 31-116) - Receive Only 1.5 Content of the packaging 1 Li-Ion battery pack 1800mAh 7.4V 1 fast desktop charger use. NOTE:

1 wall adaptor 1 belt clip If any item is missing, please verify with your Pofung dealer. 2. BATTERY INFORMATION 2.1 Charging the Battery Pack The Li-ion battery pack is not charged at the factory; please charge it before use. Charging the battery pack for the first time after purchase or extended storage (more than 2 months) may not bring the battery pack to its normal maximum operating capacity. Best operation will require fully charging/ discharging the battery two or three times before the operating capacity will reach its best performance. The battery pack life may be depleted when its operating time decreases even though it has been fully and correctly charged. If this is the case, replace the battery pack. 2.2 Charger Supplied Please use the specified charger provided by Pofung. Other models may cause explosion and personal injury. After installing the battery pack, and if the radio displays low battery with a voice prompt, please charge the battery. 2.3 Use Caution with the Li-ion Battery a. Do not short the battery terminals or throw the battery into a fire. Never attempt to remove the casing from the battery pack, as Pofung cannot be held responsible for any accident caused by modifying the battery. b. The ambient temperature should be between 5-40 (40F - 105F) while charging the battery. Charging outside this range may not fully charge the battery. c. Please turn off the radio before inserting it into the charger. It may otherwise interfere with correct charging. d. To avoid interfering with the charging cycle, please do not cut off the power or remove the battery during charging until the green light is on. e. Do not recharge the battery pack if it is fully charged. This may shorten the life of the battery pack or damage f. Do not charge the battery or the radio if it is damp. Dry it before charging to avoid damage. When keys, ornamental chain or other electric metals contact the battery terminal, the battery may become damage or injure a human. If the battery terminals are short circuited it will generate a lot of heat. Take care when carrying and using the battery. Remember to put the battery or radio into an insulated container. Do not the battery pack. WARNING put it into a metal container. 2.4 How to Charge a. Plug the AC adaptor into the AC outlet, and then plug the cable of the AC adaptor into the DC jack located on the back of the charger. The indicator light blinks orange and is then ready to charge a battery. b. Plug the battery or the radio into the charger. Make sure the battery terminals are good in contact with charging terminals. The indicator light turns to red--- charging begins. c. It takes approximately 2-5 hours to fully charge the battery. When the lamp lights green, the charging is completed. Remove the battery or the radio unit with its battery from socket. When charging a radio (with battery) the indicating lamp will not turn into green to show the fully charged status if the radio is powered on. Only when the radio is switched off will the lamp indicate normal operation. The radio consumes energy when it is power-on, and the charger cannot detect the correct battery voltage when the battery has been fully charged. So the charger will charge the battery in constant voltage mode and fail to indicate correctly when the battery has been fully charged. 2.5 LED Indicator STATUS No Battery Charge Normally Fully Charged Trouble Green and red alternately flashing LED Red Green Red blinks fast for a long time NOTETrouble means battery too warm, battery short-circuited or charger short-circuited. 2.6 How to Store the Battery a. If the battery needs to be stored, keep it in status of 80% discharged. b. It should be kept in low temperature and dry environment. c. Keep it away from hot places and direct sunlight. Do not short circuit the battery terminals. Never attempt to remove the casing from the battery pack. Never store the battery in unsafe surroundings, as a short may cause an explosion. Do not put the battery in a hot environment or throw it into a fire, as it may cause an explosion. 3. INSTALLATION OF ACCESSORIES Before the radio is ready for use we need to attach the battery pack, as well as charge the battery. 3.1 Installing the belt clip tighten the screws. you hear a "click" sound. a. Install the fixing head: Install the random belt clip fixing head in the slot on the back of the two-way radio and b. Insert the rotating belt clip: Slide the fixed head of the machine along the guide of the rotating back clip until c. Remove the belt clip: Use the key to press the disassembly engine upwards until it releases, and then push the belt clip with your thumb until the belt clip is removed. Before attaching or removing the battery make sure your radio is turned off by turning the power/volume knob Insert the two protrusions on the front of the battery into the notches on the bottom of the radio, and then press the tail of the battery toward the radio until you hear a "click". 3.2 Installing the battery pack all the way counter-clockwise. Remove the battery pack Turn off the radio. Then lift the battery push button at the end of the battery in the direction indicated by the arrow to disengage the tail of the battery from the intercom and remove the battery backwards. 3.3 Installing the Additional Speaker/Microphone (Optional) a. Use a flat-blade screwdriver to unscrew the screw at the lower end of the cover counterclockwise to remove the headset cover. b. Insert the protruding part of the lower end of the headset into the slot indicated by the arrow in the figure below, and then align the nut on the upper end of the headset with the corresponding threaded hole of the transceiver and rotate it clockwise until it is tightened. NOTE: Please install accessories correctly; otherwise the waterproof performance of this product may be 4. RADIO OVERVIEW 4.1 Buttons and controls of the radio 2. Led: transmission (red); reception (green) 4. Power / Switch / Volume control: Rotate to switch on/off the radio and adjust the volume affected. 1. Antenna 3. Flashlight 5. Speaker 6. Microphone 7. LCD display 8. EXIT: press to exit the Menu and functions. A/B (appears on the display): push to select the desired frequency

(VHF or UHF) in the main or secondary display 9. #

: Keypad lock. Long pressure: the keypad will be locked. Short pressure: high or low power selection 10. PTT A: Transmit directly in A band. There is no need to press the EXIT button to switch to the A band. 11. PTT B: Transmit directly in B band. There is no need to press the EXIT button to switch to the B band. 12. SK1: Press it activate the FM radio. If you keep it pressed for 3 seconds you will hear an alarm note and the 13. SK2: Press and hold: to activate the Monitor function. Short press: turns the flashlight on. Press it again to radio will switch to alarm mode;

issue an emergency light 14. / keys: to select the functions/menu 15. MENU: enter the MENU functions and confirms the selection. In the off state, press and hold this key to turn on the radio, allowing switching between frequency mode or channel mode 16. *SCAN: Reverse frequency/SCAN. Press to activate the Reverse frequency; keep it pressed to activate the SCAN function 17. MIC/SP: External speaker/mike jacks 18. 1800mAh Li-Ion battery pack 19. Battery release latch 4.2 Main controls and parts of the radio LCD Display 1. These symbols show that you set a DCS or CTCSS code in tx or rx. In tx mode it appears while you are transmitting, while in rx mode it is shown also in stand-by condition. 2. Received signal strength. 3. Low power selection 4. This letter is displayed when the Dual Watch function is active. 5. VOX function enabled. (GMRS Version does not support) 6. Appears when a positive shift is activated. 7. Appears when a negative shift is enabled. 8. Reverse frequency 9. Narrow bandwidth: N = narrow. When the wide (W) bandwidth is activated, no icon is displayed. 10. This icon indicates the keypad lock. To unlock it press [#

] . 11. Battery level indicator. When the battery is almost used up, the icon starts blinking and the transmission is blocked. Charge the radio. 12. Indicates the channel number that you stored 13. When the radio is in reception mode, this icon is displayed 14. Depending on the setting, it will show the frequency in use, the channel name, the menu setting, etc 15. Indicates the VFO in use and the current menu or function setting. This icon is displayed close to the band in use or to the menu settings. Battery Level Indicator When the battery level indicator reads the battery is depleted. At this point the radio will start beeping periodically as well as flash the backlight of the display and when voice prompts are enabled, a "Low Voltage"

announcement will be heard, indicating that you need to change your battery or put your radio in the charger. 4.3 Status Indications The status LED has a very simple and traditional design. LED Indicator Constant Red Constant Green Radio Status Transmitting. Receiving. 4.4 Main keypad controls

[SK1] key: Press it for a short time to turn on the FM radio. Press it again to turn it off. Press it for a long time you will activate the alarm function. Press it again to turn off this feature.

[SK2] key: Press it for a short time to light up the flashlight. If you push this button again, the flashlight will light up to strobe mode. Press [SK2] a third time to turn off the flashlight. To activate the Monitor function presses the button for a long time.

[MENU] key: It is used for activating the MENU, choose each MENU selection and confirm the parameter. In the off state, press and hold this key to turn on the radio, allowing to switch between frequency (VFO) mode or memory (MR) mode. referred to as Channel mode. To save frequencies to channel memory you must be in Frequency (VFO) mode. Memory mode is sometimes also

[] key: Press it for more than 2 seconds, the channel and frequency will move upwards rapidly; in SCAN mode, press this control to move the scanning upwards.

[] key: Keep it pressed it for more than 2 seconds, the channel and frequency will move downwards rapidly;

in SCAN mode, press this control to move the scanning downwards.

[EXIT/AB] key: press to exit the Menu and functions. A/B (appears on the display): push to select the desired frequency (VHF or UHF) in the main or secondary display. When listening to broadcast FM, the [EXIT] key switches between 65-75 MHz and 76-108 MHz band. Numeric keypad to send a corresponding DTMF code. With these keys you can input the information or your selections on the radio. In tx mode, push the number keys

*SCAN Key A short momentary press of the key enables the reverse function. When listening to broadcast FM a momentary press will start the scanning. Scanning in broadcast FM will stop as soon as an active station is found, regardless of scanner resume method. To enable the scanner, press and hold the [*SCAN] key for about two seconds. The Pofung UV82 features a battery voltage meter that the current voltage of the battery on the display. To see the voltage displayed, press and hold the [0SQL] key for about two seconds. Zero 0 Key

key If you press shortly [#

] you will switch to High /Middle /Low output power. If you press this button for more than 2 seconds you will lock/unlock the keypad. 5. BASIC OPERATIONS 5.1 Power on the radio Turning the unit on To turn the unit on, simply rotate the volume/power knob clockwise until you hear a "click". If your radio powers on correctly there should be an audible double beep after about one second and the display will show a message or flash the LCD depending on settings for about one second. Then it will display a frequency or channel. If the Voice prompt is enabled, the voice will announce "frequency mode" or "channel mode". Turn the volume/power knob counter-clock wise all the way until you hear a "click". The unit is now off. To turn up the volume, turn the volume/power knob clock-wise. To turn the volume down, turn the volume/power knob counter-clock-wise. Be careful not to turn it too far, as you may inadvertently turn your radio Turning the unit off 5.2 Adjusting the volume off. 5.3 Making a call mode or channel mode. NOTE: Press the [EXIT] key to switch the main channel to the other channel if there is 2 channels shown on the display. In the off state, press and hold the [MENU] key to turn on the radio; it will switch between frequency Channel mode call: After selecting a channel, hold down the [PTT] key to initiate a call to the current channel. Speak into the microphone with normal tone. Initiate a call, the red LED is on. Frequency mode call: The off state, hold press [MENU] key to open the radio, switching to the frequency mode, the frequency range allowed entering, press the [PTT] key, a call to the current channel. Speak into the microphone with normal tone. Initiate a call, the red LED is on. Receive a call: When you release the [PTT] key, you can answer it without any action. When receiving a call, the green LED is on. NOTE: To ensure the best reception volume, keep the distance between the microphone and the mouth at the time of transmission from 2.5 cm to 5 cm. 5.4 Channel selection There are two modes of operation: Frequency (VFO) mode, and Channel or Memory (MR) mode. For everyday use, Channel (MR) mode is going to be a whole lot more practical than Frequency (VFO) mode. However, Frequency (VFO) mode is very handy for experimentation out in the field. Frequency (VFO) mode is also used for programming channels into memory. In Channel (MR) mode you can navigate up and down the channel by using the and keys. Ultimately which mode you end up using will depend entirely on your use case. 5.5 Frequency (VFO) mode In Frequency (VFO) mode you can navigate up and down the band by using the and keys. Each press will increment or decrement your frequency according to the frequency step you've set your transceiver to. You can also input frequencies directly on your numeric keypad with kilohertz accuracy. The following example assumes the use of a 12.5 kHz frequency step. Example. Entering the frequency 462.6125 MHz on display A a. The off state, hold press [MENU] key to open the radio, switching to the frequency (VFO) mode. b. Press [EXIT] until the icon appears next to the upper display. c. Enter [4][6][2][6][1][2][5] on the numeric keypad. WARNING!

Just because you can program in a channel does not mean you're automatically authorized to use that frequency. Transmitting on frequencies you're not authorized to operate on is illegal, and in most jurisdictions a serious offence. If you get caught transmitting without a license you can and will get fined, and in worst case sent to jail. However, it is legal in most jurisdictions to listen. Contact your local regulatory body for further information on what laws, rules and regulations apply to your area. 5.6 Channel (MR) mode The use of Channel (MR) mode is dependent on actually having programmed in some channels to use. Once you have channels programmed and ready, you can use the and keys to navigate between channels. 6. ADVANCED FEATURES a. In frequency mode, press [*SCAN] key for more than 2 seconds. The radio will start scanning the frequency according to the set frequency step. b. You can change the scanning direction with the and keys. 6.1 Frequency scanning This function can scan the frequency. c. Press any key to stop the scanning. Note: for Scan mode, see Menu No.18. 6.2 Channel scanning This function can scan the channels. a. In channels mode, press [*SCAN] key for more than 2 seconds. The radio will start scanning according to the channel you set. b. You can change the scanning direction with the and keys. c. Press any key to stop scanning. Note: for Scan mode, see Menu No.18. 6.3 Search CTCSS/DCS Code With this function you can search and store the CTCSS/DCS code used by other radios. Procedure:

a. In frequency mode press [MENU]+[1][1]. b. Press [MENU] key again. c. Press [*SCAN] key; CT will blink on the display. d. When another radio is transmitting, the display will show the CTCSS/DCS code. e. After searching the CTCSS code, the radio will beep and stop scanning. f. After setting, press [MENU] key for confirmation and store, or press [PTT] or [EXIT] key to return to standby NOTE 1: the DCS scanning has the same procedure of CTCSS code, but you have to select MENU+10 to enter NOTE 2: if CTCSS has not searched the code, you can search using the DCS mode. 6.4 CursorConversion (A/B) indicated by the cursor. Directly press [EXIT] key to move the cursor up and down. Then, you can modify or confirm the parameters Important1: UV82 has a dual-frequency display function. In frequency mode, you will see on the display two mode. scanning. different receiving and transmitting frequencies; while in channel mode the two different channels will be Important2: In frequency or channel mode, press the [EXIT] key to shift between the main channel A and the displayed. sub-channel B on the display indicates on which channel (main channel A or sub channel B) you are operating. is displayed next to the channel. 6.5 High/ Low power fast selection In channel mode, press [#

] key to shift between high/ low power. This function locks the keypad to prevent accidental pressure of the controls. To unlock the keypad, press [#

] for more than 2 seconds. 6.6 Keypad lock 6.7 FM Radio (FM) The frequency range to listen to the radio is 65-108MHz. When listening to broadcast FM, press [EXIT] key switches between 65-75 MHz and 88-108 MHz band. a. In frequency or channel mode, Press [SK1] to turn on the radio. b. Select the desired radio frequency with the or keys or input the frequency. Or Press [* SCAN] to automatically search a radio station. c. Press [SK1] to exit FM radio. Note: FCC version only supports 88-108MHz 6.8 Flashlight This function is very useful for night illumination. To turn it on press MON; push it again, the flash light will be strobe; push it again: it will turn off. 6.9 TX 1000Hz, 1450Hz, 1750Hz, 2100Hz repeaters tone Press [PTT] + [SOS] to send 1750Hz repeaters tone. This function is useful for communications through repeaters. If you have the keypad lock enabled on your radio, you can still send a 1750Hz tone the regular way without having to unlock your radio. 6.10 NOAA weather radio/ scan NOAA weather radio. keys until the channel 117 ~ 127. Your radio has a NOAA weather radio function, to enable the user to receive weather reports from designated NOAA stations. Your radio also has a NOAA weather scan function to enable the user to scan all 11 channels of the To select the NOAA channel, enter the channel number 117 ~ 127 directly in the channel mode or press the or To scan the NOAAWEATHER channel, press and hold the [* SCAN] key for 3 seconds in channel mode. During scanning, press any key to exit the scanning state. NOTE: The radio's NOAA weather channel is in the 117-127 channels, and the detailed frequency is NOAA WEATHER (WX) RADIO FREQUENCY CHART. 6.11 Manual Programming (Channels Memory) Memory channels are an easy way to store commonly used frequencies so that they can easily be retrieved at a The Pofung UV82 features 128 memory channels that each can hold: Receive and transmit frequencies, transmit power, group signaling information, bandwidth, ANI/ PTT-ID settings and a six character alphanumeric identifier later date. or channel name 1 . Frequency Mode vs. Channel Mode In the off state, press and hold the [MENU] key to turn on the radio; it will switch between frequency mode or channel mode. These two modes have different functions and are often confused. Frequency Mode (VFO) : Used for a temporary frequency assignment, such as a test frequency or quick field programming if permitted. Channel Mode (MR) : Used for selecting preprogrammed channels. Ex 1. Programming a Channel Repeater Offset with CTCSS Tone EXAMPLE New memory in Channel 10:

RX = 462.5750 MHz TX = 467.5750 MHz (This is a (+ 5) Offset) TX CTCSS tone 123.0 a. Turn off the radio. b. Hold press [MENU] key to open the radio, switching to the frequency mode. Channel number at the right will disappear. c. [MENU] [2][8] [MENU] [1] [0] [MENU] [EXIT]

Deletes Prior Data in channel (Ex. 10) d. [MENU] [1][3] [MENU] 123.0 [MENU] [EXIT]

Selects desired TX encode tone e. Enter RX frequency (Ex. 4625750) f. [MENU] [2][7] [MENU] [1][0] [MENU]

Enter the desired channel (Ex 10)

-->>[EXIT]

RX has been added g. Enter TX frequency (Ex. 4675750) h. [MENU] [2][7] [MENU] [1][0] [MENU]

Enter the same channel (Ex 10)

-->> [EXIT]

TX has been added i. In the off state, press and hold the [MENU] key to turn on the radio, return to MR mode, and the channel number will reappear. Ex 2. Programming a Simplex Channel with CTCSS tone EXAMPLE New memory in Channel 10:

RX = 462.5750 MHz TX CTCSS tone 123.0 a. Change from Menu to Menu by pressing the [EXIT] button. b. The off state, hold press [MENU] key to open the radio, return to the frequency mode. Channel number at the right will disappear. c. [MENU] [2][8] [MENU] [1] [0] [MENU] [EXIT]

Deletes Prior Data in channel (Ex. 10) d. [MENU] [1][3] [MENU] 123.0 [MENU] [EXIT]

Select desired TX encode tone (Ex 123 CTCSS)

-->>Use [EXIT] to select Upper display e. Enter RX frequency (Ex. 462.5750) f. [MENU] [2][7] [MENU] [1][0] [MENU]

Enter the desired channel (Ex 10)

-->> [EXIT]

Channel has been added g. In the off state, press and hold the [MENU] key to turn on the radio, return to MR mode, and the channel number will reappear. 6.12 Repeaters Programming The following instructions assume that you know what transmit and receive frequencies your repeater employs, and that you're authorized to use it. a. Turn off the radio. Press and hold the [MENU] key to turn on the radio and return to the frequencyVFO) mode. The channel number on the right will disappear. b. Use the numeric keypad to enter the repeater's output (your receiving) frequency. c. Press the [MENU] key to enter the menu. d. Enter [2][6] on the numeric keypad to get to frequency offset. e. Press [MENU] key to select. f. Use the numerical keypad to enter the specified frequency offset. See the section called 26 OFFSET - Frequency shift amount for details. g. Press [MENU] to confirm and save. h. Enter [2][5] on the numeric keypad to get to offset direction. i. Use the / keys to select + (positive) or - (negative) offset. j. Press [MENU] to confirm and save. k. Optional:

a). Save to memory, see the section called Manual programming for details. b). Set up CTCSS; see the section called CTCSS for details. l. Press [EXIT] to exit the menu. If everything went well, you should be able to make a test call through the repeater. NOTE:

procedure again. If you're experiencing problems making a connection to the repeater, check your settings and/or go through the Certain Amateur Radio repeaters (especially in Europe) use a 1750Hz tone burst to open up the repeater. To see how this is done with the Pofung UV82, see the section called 1750Hz Tone-burst. If you're still unable to make a connection, contact the person in charge of the radio system with your employer or your local amateur radio club, as the case may be. If you for some reason want to listen to the repeater's input frequency instead, press [*SCAN] key momentarily and you'll reverse your transmit and receive frequencies. This is indicated in the LCD on the radio with an R in the top row, next to the + and - for the offset direction. 7. WORKING THE MENU SYSTEM For a complete reference on available menu items and parameters, see Appendix C, Shortcut Menu operations. Note: in channel mode, the setting of these features is not possible: CTCSS/ DCS tones, wide/narrow bandwidth, PTT-ID, Busy channel lock out, channel name edit. 7.1 Basic use Using the menu with arrow keys a. Press the [MENU] key to enter the menu. b. Use the [] and [] keys to navigate between menu items. c. Once you find the desired menu item, press [MENU] again to select that menu item. d. Use the [] and [] keys to select the desired parameter. e. When you've selected the parameter you want to set for a given menu item;

a). To confirm your selection, press [MENU] and it will save your setting and bring you back to the main menu. b). To cancel your changes, press [EXIT] and it will reset that menu item and bring you out of the menu entirely. f. To exit out of the menu at any time, press the [EXIT] key. 7.2 Using short-cuts As you may have noticed if you looked at Appendix C, Shortcut Menu operations, every menu item has a numerical value associated with it. These numbers can be used for direct access of any given menu item. The parameters also have a number associated with them, see Appendix C, Shortcut Menu operations for details. Using the menu with short-cuts a. Press the [MENU] key to enter the menu. b. Use the numerical keypad to enter the number of the menu item. c. To enter the menu item, press the [MENU] key. d. For entering the desired parameter you have two options:

a). Use the arrow keys as we did in the previous section; or b). Use the numerical keypad to enter the numerical short-cut code. e. And just as in the previous section;

a). To confirm your selection, press [MENU] and it will save your setting and bring you back to the main menu. b). To cancel your changes, press [EXIT] and it will reset that menu item and bring you out of the menu entirely. f. To exit out of the menu at any time, press the [EXIT] key. g. All further examples and procedures in this manual will use the numerical menu short- cuts. 7.3 Functions and operations

(1) Squelch level (SQL) - MENU No.0 Thanks to this function you can adjust the squelch in 10 different levels:

level 0: opened squelch. With this setting, UV-82 will detect all signals, also the weakest ones, but will also receive the background noise or undesired signals. levels 1- 9: level 1 (lowest squelch level), level 9 (highest squelch level). If the squelch is set to the highest level, the radio will receive the strongest signals only.

(2) Step frequency (STEP) - MENU No.1 This function lets you select the desired frequency step. The selectable steps are the following: 2.5/5.0/6.25/10.0/12.5/20.0/25.0/50.0 KHz Note: in channel mode, this function cannot be modified.

(3) Output power (TXP) - MENU No.2 In this MENU you can select the high/ low output power. Low power =0.5W; High power = 4W Note: select the output power can improve the quality of the call, while the low output power can reduce the radiation and the battery capacity loss. Press the fast key #

to switch between the high or low output powers.

(4) Battery save (SAVE) - MENU No.3 The power save feature enables a reduction in the consumption of the battery when the radio is in standby. You have 5 selections available: OFF / 1:1 / 1:2 / 1:3 / 1:4. For example: 1:1 = 1s working and 1sbattery saving. 1:2 = 1s working and 2s battery saving.

(5) VOX Function (VOX) - MENU No.4 This function allows hands-free conversations: just speak in the direction of the microphone and the communication will be automatically activated. You can choose amongst 11 levels: OFF-10. 1 is the highest level, 10 is the lowest one. Note: GMRS Version does not support

(6) Wide/Narrow bandwidth (WN) - MENU No.5 This function is used to set the working bandwidth of the radio. You can choose between wide or narrow bandwidth. NARROW: 12.5KHz (Only used) Note: In GMRS Version, this function cannot be modified.

(7) Backlight (ABR) - MENU No. 6 With this function you can adjust the auto off time of the display backlight (1-5s). Note: we suggest you setting 4-5s levels.

(8) Dual Watch Operation (TDR) - MENU No. 7 When this function is activated, you can receive the frequency of channel A and channel B at the same time. If a signal is detected, the/ pointer will blink on the corresponding channel or frequency. Note: In Dual Watch operation mode, you can change the parameter of AB channel or frequency freely.

(9) Keypad beep (BEEP) - MENU No. 8 When this function is enabled, every time a button is pressed, you will hear a beep tone.

(10) Time-Out-Timer (TOT) - MENU No.9 The TOT function is used to prevent a too long transmission and limits the tx time: TOT temporarily stops the transmission if the radio has been used beyond the max pre-set time (for example 15s, 30s, 45s, etc).

(11) Receiving DCS (R-DCS) - MENU No.10 DCS codes are similar to access codes and can be added to channels, so as to create a sort of personal channel. They enable the radio to communicate with the users that are tuned on the same channel and have set the same DCS code. You can choose amongst:

OFF: OFF R-DCS: D023N-D754N (Normal DCS) R-DCS: D023I-D754I (Inverse DCS) channel mode.

(12) Receiving CTCSS (R-CTCSS) - MENU No.11 Note: In UV82 there are 208 groups of normal and inverse DCS codes. This function cannot be amended in As DCS codes, the CTCSS codes can be added to the channels for creating new private channels. Note: there are 50 groups of CTCSS tones. In channel mode the CTCSS tones cannot be changed.

(13) Transmitting DCS - (T-DCS) - MENU No.12 In this Menu you activate DCS codes in tx mode. You can choose between normal R-DCS (D023N-D754N) and inverted R-DCS (D023I-D754I) Note: the groups of DCS codes are 208. DCS codes cannot be changed in channel mode.

(14) Transmitting CTCSS (T-CTCSS) - MENU No.13 In this Menu you can set a CTCSS tone in tx mode. You can choose: OFF or CTCSS (67.0 to 254.1 Hz) Note: there are 50 groups of CTCSS tones. In channel mode the CTCSS tones cannot be changed.

(15) Voice function (VOICE) - MENU No. 14 With this function, you activate a voice that informs you about any operation/ selection you are doing. With this function you can set your ID-code. It can be programmed by the proper programming software. You can

(16) ANI-ID (ANI-ID) - MENU No.15 edit up to 5 digits.

(17) DTMFST (DTMFST) - MENU No.16 Determines when DTMF Side Tones can be heard from the transceiver speaker.

(18) Signal code (S-CODE) - MENU No.17 Selects 1 of 15 DTMF codes. The DTMF codes are programmed with software and are up to 5 digits each.

(19) SCAN Resume Mode (SC-REV) - MENU No.18 Thanks to this function, UV82 can SCAN in frequency or channel mode. You can choose amongst three options:

Whenever a signal is detected, the radio will suspend the SCAN for 5 seconds, and then will continue to SCAN TO: Time-operated SCAN even if the signal is still present. CO: Carrier-operated SCAN Whenever a signal is detected, the radio will stop scanning. It will resume to SCAN once the signal will disappear. SE: Search SCAN The radio will stop scanning once a signal is detected.

(20) PTT-ID (PTT-ID) - MENU No.19 With this function you can decide when sending the ANI-ID code in tx mode. You can choose amongst 4 possibilities. press PTT to turn it off OFF:

BOT:

EOT:

the code is sent when you press the PTT the code is sent when the PTT is released BOTH: the code is sent when you press and release the PTT Note: select OFF when using in case of affecting the radio.

(21) PTT ID delay (PTT-LT) - MENU No.20 In this MENU you can set the delay time (0-30ms) sending the PTT-ID. Note: select 0 in normal using.

(22) Channel A Display Mode (MDF-A) - MENU No.21 This function is used to set the display mode of channel A. Display modes:

FREQ.:

Frequency + channel No. CH:

Channel number NAME: Channel name be edited.

(23) Channel B Display Mode (MDF-B) - MENU No.22 Note: Channel name mode must be set by the programming software. Up to three numbers or characters can This function is used to set the display mode of channel B. Display modes:

FREQ.: Frequency + channel No. CH:

Channel number NAME: Channel name Note: Channel name mode must be set by the programming software. Up to three numbers or characters can When this function is on, it may prevent other radios interference. If the selected channel is being used by other be edited.

(24) Busy Channel Lock (BCL) - MENU No. 23 radios, when you press key PTT, your radio cannot transmit. Release the PTT and transmit as soon as the frequency is no longer busy.

(25) Auto Keypad Lock (AUTOLK) - MENU No.24 When this feature is activated, the keypad will be automatically locked after 15s; this prevents accidental pressure of any keys.

(26) Frequency offset direction (SFT-D) - MENU No.25 Using this function, you can set the direction of the frequency offset in rx and tx. You have the following options:

+: Positive offset;

-: Negative offset;

OFF: no offset enabled in channel mode. Note: you should set different frequency deviation according to the repeaters selected. This function is not

(27) Frequency offset (OFFSET) - MENU No. 26 In this MENU you can set the deviation between tx and rx. The frequency offset of this radio is 0-69.990MHz.

(28) Channel store - (MEM-CH) - MENU No. 27 When the radio is in frequency working mode or standby mode, input the desired frequency or parameters directly. To set a CTCSS tone or a DCS code in tx or rx on the stored channel, refer to paragraphs MENU 10-13 Note: You cannot overwrite a stored channel, you have to delete it first. See following paragraph No.28.

(29) Channel Delete (DEL-CH) - MENU No.28 In this menu you can delete a channel of the radio.

(30) Standby backlight (WT-LED) - MENU No.29 In this MENU you can choose the color of the backlight when the radio is in standby mode. You can choose amongst:

OFF (backlight off) BLUE PURPLE ORANGE

(31) RX backlight (RX-LED) - MENU No. 30 In this MENU you can choose the backlight color when the radio is receiving. You can choose amongst:

OFF (backlight off) BLUE PURPLE ORANGE Available colors:

OFF (backlight off) BLUE PURPLE ORANGE

(32) TX backlight (TX-LED) - MENU No.31 You can choose the backlight color when the radio is transmitting.

(33) Alarm Mode (AL-MOD) - MENU No.32 This function can set the tone alarm/code alarm/site alarm of the radio. Keep pressed the [CALL] key for 3 seconds to start the alarm tone. The following three options can be selected:

SITE: the speaker emits an alarm tone but the radio doesnt transmit;

TONE: the speaker emits an alarm tone and the radio transmits it;

CODE: the speaker emits an alarm tone and the radio transmits it followed by ANI-ID code.

(34) Dual Watch (TDR-AB) - Menu No.34 When this function is on, you may receive signals of A/B channel or frequency. It can also be used for cross band receiving and transmitting. You can choose amongst the following settings:

OFF: UV82 can receive in both VFO (not simultaneously); or will blink on the transmitting frequency band. A: the radio can receive in both VFO (not simultaneously) but can transmit in VFO A only. B: UV82 can receive in both VFO (not simultaneously) but can transmit in VFO B only. If you choose option A, it means that 462.575MHz is the tx frequency band, while 467.5875MHz is the rx frequency band; the upper VFO shows 462.575 MHz while in the lower VFO 467.5875MHz will be displayed; you can receive on both 462.575 MHz and 467.5875 MHz, but can transmit on 462.575 MHz only. While if you choose option B, 467.5875MHz is the tx frequency band and 462.575MHz is the rx frequency band. In the upper VFO 462.575 MHz will be displayed while the lower VFO will show 467.5875 MHz; you can receive on both 462.575 MHz and 467.5875 MHz, but transmit on 467.5875 MHz only. Example: the LCD displays

(35) Side tone elimination (STE) - Menu No. 35 This feature is helpful to eliminate the annoying audio tone after the transmission is finished (end transmission

(36) Side tone elimination in communication through repeater (RP-STE) - Menu No. 36 noise muffler). This function is used when the radio operates through a repeater; when the PTT is released, the repeater will emit the end transmission tone to confirm it is working. Available settings:

OFF 1,2,3,4,5,.10 to set the delay time. Note: Please disable this function in normal using, lest affect your normal conversation.

(37) Delay time of side tone elimination in communication through repeater (RPT-RL) - Menu No.37 With this function you have the confirmation that the repeater has transferred the signal. You can choose amongst: OFF 1,2,3,4,5,.10 to set the delay time.

(38) Display mode at the turning on (PONMSG) Menu No.38 With this function you can set the display mode when the radio is turned on. Available options:

When the PTT is released, the radio will beep to confirm to other users that you have finished your transmission With this function you can reset the transceiver to the factory-programmed settings and parameters. After that, FULL: full frequency character is displayed. MSG: UV-82 is displayed.

(39) Roger beep (ROGER) - Menu No. 39 and that they can start talking.

(40) Reset (RESET) - Menu No.40 you can set the desired functions. There are two types of reset:

VFO: Menu Reset ALL: Menu and channel Reset You hold down the [PTT] + [SOS] key. having to unlock your radio.

(41) 1000Hz, 1450Hz, 1750Hz, 2100Hz Repeater Tone (R-TONE) - Menu No.41 With this function you can select 1000Hz, 1450Hz, 1750Hz, 2100Hz repeater tone. To send out a repeater tone;

If you have the keypad lock enabled on your radio, you can still send a 1750Hz tone the regular way without 8. ON-LINE SERVICE AND SUPPORT The Pofung website provides additional information about obtaining service or support for the Pofung line of two-way radios and accessories. Visit: www.pofungshop.com Mail: service@pofungshop.com FCC Licensing Information This pofung radio operates on Commercial/ Land Mobile frequencies which require a license from the Federal Communications Commission (FCC) for business, personal, education and recreational use. To obtain forms, call the FCC forms hotline at: 1-800-418-3676 or go to http://www.fcc.gov For questions concerning commercial licensing, contact the FCC at 1-888CALL-FCC (1-888-225-5322). Appendix A. Trouble shooting guide Phenomena Analysis Solution You cannot turn on the radio. The battery may be installed improperly. The battery power may run out. The battery may suffer from poor contact caused by dirty or damaged battery contacts. Remove and reattach the battery. Recharge or replace the battery. Clean the battery contacts or replace the battery. During receiving, the voice is weak or intermittent. You cannot communicate with other group members. You hear unknown voices or noise. You are unable to hear anyone because of too much noise and hiss. The radio keeps transmitting. You cannot use the keys. The battery voltage maybe low. The volume level may be low. The antenna maybe loose or maybe installed incorrectly. The speaker maybe blocked. The frequency or signaling type maybe inconsistent with that of other members. You may be too far away from other members. You may be interrupted by radios using the same frequency. The radio in analog mode maybe set with no signaling. You may be too far away from other members. You may be in an unfavorable position. For example, your communication may be blocked by high buildings or blocked in an underground area. It may be the result of external disturbance (such as electromagnetic interference). VOX may be turned on or the headset is not installed in place The keypad may not work temporarily. Recharge or replace the battery. Increase the volume. Turnoff the radio, and then remove and reattach the antenna. Clean the surface of the speaker. Verify that your TX/RX frequency and signaling type are correct. Move towards other members. Change the frequency, or adjust the squelch level. Request your dealer to set signaling for the current channel to avoid interference Move towards other members. Move to an open and flat area, restart the radio, and try again. Stay away from equipment that may cause interference. Turn off the VOX function. Check that the headphones are in place. Restart the radio. NOTE: If the above solutions cannot fix your problems, or you may have some other queries, please contact your dealer for more technical support. Appendix B. - Technical Specifications General Frequency Range 88-108MHz (FM Rx)

(VHF)136-174MHz (RX)

(UHF)400-520MHz (Rx) GMRS 462.5500 ~ 467.7250 MHz (RX & TX) 30 GMRS Channels + 11NOAA Weather + 87Scanner Channels Memory Channel Operation Voltage Battery Capacity DC 7.4 V 10%

1800mAH (Li-Ion) Frequency Stability 2.5ppm Operating Temperature

-20 to +60 Mode of Operation Antenna Impedance Simplex 50ohm Transmitter Part RF Output Power FM Modulation 4W/0.5W (GMRS) 11K0F3E@12.5KHz Spurious Emission

-13dBm1GHz -13dBm1GHz Adjacent Channel Power 60dB @ 12.5 KHz Transmission current 1600mA Receiver Part Receive Sensitivity 0.25V (12dB SINAD) Adjacent Channel Selectivity 55dB@12.5KHz Inter Modulation and Rejection 55dB@12.5KHz Conducted Spurious Emission

-57dB@12.5KHz Rated Audio Power Output 1W @16 ohms Receive current 380mA Rated Audio Distortion 5%

NOTE: All specifications may be modified without prior notice or liability. Thank you. Appendix C. - GMRS Frequency Chart (MHz) CH.No CH.Freq. CH.No CH.Freq. CH.No CH.Freq. 1 2 3 4 5 6 7 8 9 10 462.5625 462.5875 462.6125 462.6375 462.6625 462.6875 462.7125 467.5625 467.5875 467.6125 11 12 13 14 15 16 17 18 19 20 467.6375 467.6625 467.6875 467.7125 462.5500 462.5750 462.6000 462.6250 462.6500 462.6750 21 22 23 24 25 26 27 28 29 30 462.7000 462.7250 467.5500 467.5750 467.6000 467.6250 467.6500 467.6750 467.7000 467.7250

* Channels 8~14 are low-power license free channels. Channels 23~30 are GMRS repeater channels. Appendix D. - Weather Channel Assignments Channel Number RX Frequency MHz Weather Channel Channel Number RX Frequency MHz Weather Channel 117 118 119 120 121 122 162.550 162.400 162.475 162.425 162.450 162.500 NOAA1 NOAA2 NOAA3 NOAA4 NOAA5 NOAA6 123 124 125 126 127

162.525 161.650 161.775 161.750 162.000

NOAA7 NOAA8 NOAA9 NOAA10 NOAA11

Appendix E. - Shortcut Menu operations MENU No. Name

(Full Name) Enter item LCD display Selectable SQL - Squelch Level MENU+0 STEP Step Frequency MENU+1 2.5K/5.0K/6.25K/10.0K 12.5K/20.0K/25.0K/50.0K 0-9 Levels 0:Lowest 9:Highest HIGH:4W Low:0.5W OFF:

1:1 2:2 3:3 4:4 OFF, 1-9 OFF: off OFF ON OFF ON 1:Highest Sensitivity 9:Highest Sensitivity NARR:12.5K (GMRS Only ) OFF/1,2,389,10

*Time-out for the LCD backlight. (seconds)

*Monitor [A] and [B] at the same time. The display with the most recent activity ([A] or [B]) becomes the selected display.

*Allows audible confirmation of a key press. 15,30600S

*This feature provides a safety switch that limits transmission time to a programmed value. This will promote battery conservation by not allowing you to make excessively long transmissions, and in the event of a stuck PTT switch it can prevent interference to other users as well as battery depletion OFF D023ND754N D023I D754I OFF 67.0HZ254.1HZ OFF D023ND754N D023I D754I OFF 67.0HZ254.1HZ

*Mutes the speaker of the transceiver in the absence of a specific low-level digital signal. If the station you are listening to does not transmit this specific signal, you will not hear anything.

*Mutes the speaker of the transceiver in the absence of a specific and continuous sub-audible signal. If the station you are Listening to does not transmit this specific and continuous signal, you will not hear anything.

*Transmits a specific low-level digital signal to unlock the squelch of a distant receiver (usually a repeater).

*Transmits a specific and continuous sub audible signal to unlock the squelch of a distant receiver (usually a repeater). 0 1 2 3 4 5 6 7 8 TXP Transmit Power MENU+2 SAVE - Battery Saving MENU+3 VOX - VOX MENU+4 WN-Wide/Narrow Bandwidth MENU+5 ABR Auto Backlight MENU+6 TDR Dual Watch Operation MENU+7 BEEP - Keypad Beep MENU+8 9 TOT- Time-Out-Timer MENU+9 10 R-DCS - Receiver DCS MENU+10 11 R-CTCS - Receiver CTCSS MENU+11 12 T-DCS -Transmitter DCS MENU+12 13 T-CTCS - Transmitter CTCSS MENU+13 OFF CHI ENG 14 VOICE - Voice Reminding MENU+14 15 ANI-ID -ANI-ID MENU+15 It can be programmed by software

*Allows audible voice confirmation of a key press. codes DTMF codes 1,,15 passed disappears OFF: No DTMF Side Tones are heard DT-ST : Side Tones are heard only from manually keyed DTMF ANI-ST: Side Tones are heard only from automatically keyed DT+ANI : All DTMF Side Tones are heard TO : Time Operation - scanning will resume after a fixed time has CO : Carrier Operation -scanning will resume after the signal SE : Search Operation -scanning will not resume OFF: No ID is sent BOT: The selected S-CODE is sent at the beginning EOT: The selected S-CODE is sent at the ending BOTH : The selected S-CODE is sent at the beginning and ending 0,1,2,50ms

*PTT-ID Delay (milliseconds) FREQ: Displays programmed Frequency CH: Displays the channel number NAME: Displays the channel name

*Note: Names must be entered using software. FREQ: Displays programmed Frequency CH: Displays the channel number NAME: Displays the channel name

*Note: Names must be entered using software. OFF ON OFF ON

*When ON, the keypad will be locked if not used in 8 seconds. Pressing the [#

] key for 2 seconds will unlock the keypad. OFF: TX = RX (simplex)

+: TX will be shifted higher in frequency than RX

- : TX will be shifted lower in frequency than RX

*Specifies the difference between the TX and RX frequencies 00.00069.990 000127 MR/Channel Mode 000127 BCL Busy Channel Lock-out MENU+23

*Disables the [PTT] button on a channel that is already in use. The transceiver will sound a beep tone and will not transmit if the [PTT] button is pressed when a channel is already in use. MEM-CH - Store a Memory Channel MENU+27

*This menu is used to either create new or modify existing channels (0 through 127) so that they can be accessed from DEL-CH - Delete a memory channel MENU+28

*This menu is used to delete the programmed information from the specified channel (0 through 127) so that it can either be programmed again or be left empty. WT-LED- Standby Backlight RX-LED- Receive Backlight MENU+29 OFF/ BLUE/ ORANGE/ PURPLE MENU+30 OFF/ BLUE/ ORANGE/ PURPLE 16 DTMFST - DTMFST MENU+16 17 S-CODE - Signal Code MENU+17 18 SC-REV - Scanner Resume Method MENU+18 19 PTT-ID - PTT-ID MENU+19 20 PTT-LT PTT ID delay MENU+20 MDF-A - Channel A Display Mode MENU+21 MDF-B - Channel B Display Mode MENU+22 AUTOLK Automatic Keypad Lock MENU+24 SFT-D Frequency Offset Direction MENU+25 OFFSET -Frequency shift amount MENU+26 21 22 23 24 25 26 27 28 29 30 31 TX-LED- Transmit Backlight MENU+31 OFF/ BLUE/ ORANGE/ PURPLE 32 AL-MOD - Alarm Mode MENU+32 33 BAND - Band Selection MENU+33

*In VFO/Frequency mode, sets [A] or [B] to the VHF or UHF SITE: Sounds alarm through your radio speaker only TONE: Sending alarm tone CODE: Sending alarm code VHF:136-174MHz(RX) UHF:400-520MHz(RX) band. OFF ON OFF A band transmit (Upper row frequency) B band transmit (Bottom row frequency)

*When enabled, priority is returned to selected display once the signal in the other display disappears.

*This function is used eliminate squelch tail noise between pofung handhelds that are communicating directly (no repeater). Reception of a 55 Hz or 134.4 Hz tone burst mutes the audio long enough to prevent hearing any squelch tail noise. OFF/ 1,2,310

*This function is used eliminate squelch tail noise when communicating through a repeater. turned on. OFF ON that the transmission has ended. VFO: Menu initialization ALL: Menu and channel initialization

*Resets the radio to factory defaults, with some exceptions. 1000Hz/1450Hz/1750Hz/2100Hz

*To send out a repeater tone; You hold down the [PTT] + [SOS]

key. 34 selection while in Dual MENU+34 TDR-AB - Transmit Watch mode STE - Squelch Tail Elimination MENU+35 RP-STE-Squelch Tail Elimination MENU+36 35 36 37 38 40 RESET Restore defaults MENU+40 41 R-TONERepeater Tone MENU+41 RPT-RL - Delay the squelch tail of repeater MENU+37 OFF/ 1,2,310

*Delay the Tail Tone of Repeater (X100 milliseconds) PONMSG-Power On Message MENU+38 FULL: Performs an LCD screen test at power-on MSG : Displays a 2-line power on message

*Controls the behavior of the display when the transceiver is 39 ROGER - Roger Beep MENU+39

*Sends an end-of-transmission tone to indicate to other stations Disclaimer The Company endeavors to achieve the accuracy and completeness of this manual, but no warranty of accuracy or reliability is given. All the specifications and designs are subject to change without notice due to continuous technological development. No part of this manual may be copied, modified, translated, or distributed in any manner without the prior written consent of the Company. We do not guarantee, for any particular purpose, the accuracy, validity, timeliness, legitimacy or PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY completeness of the third-party products and contents involved in this manual. Address: 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Phone: +86-595-86752889 Fax: +86-595-86754889 E-Mail: sales @pofungshop.com Http://www.pofungshop.com Print version: UV82_FCC_ V1

Internal Photos OPEN VIEW-1 OF EUT OPEN VIEW-2 OF EUT OPEN VIEW-3 OF EUT OPEN VIEW-4 OF EUT INTERNAL VIEW-1 OF EUT INTERNAL VIEW-2 OF EUT INTERNAL VIEW-3 OF EUT INTERNAL VIEW-4 OF EUT INTERNAL VIEW-5 OF EUT

External Photos TOTAL VIEW OF EUT TOP VIEW OF EUT BOTTOM VIEW OF EUT FRONT VIEW OF EUT BACK VIEW OF EUT LEFT VIEW OF EUT RIGHT VIEW OF EUT

PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Date: June 15, 2018 Statement We, PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY states that our device, FCC ID: 2AJGM-UV82 ,has no space to put the label except the battery compartment of this device. It is visible to the users as they purchase the products and install the battery. Regards PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY Contact person: Peter Wang Title: Manager

FCC ID Label Location FCC ID: 2AJGM-UV82 WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Agent Authorization Company: PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY Address: 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Product Name: Two-way radio Model Number(s): UV-82, UV82IC, P82UV, UV82X, UC82 Pro,UV-82 Plus, GT-5, UV-

82HP, Mate82 Product Description: GMRS Two-way radio We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Date: Jan. 12, 2021 Signature:

Name:

Peter Wang Title:

General Manager Company: PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY

PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Jan. 12, 2021 To: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Subject: Attestation statement regarding the Mobile Radio frequency Applicant: PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong TYPE OF QEUIPMENT: Licensed Non-Broadcast Transmitter Held to Face FCC ID: 2AJGMUV82 Dear Sir or Madam I attest that the product has one antenna, one battery capacity, one body-worn and audio accessory. And that the product could program the frequency on computer through interface by manufacturer, is incapable of tuning, or readily being altered, by the end-user. Please contact the undersigned if you have any questions or need any further information. Regards Signature:

Name, Job Title and Dept.: Peter Wang / General Manager

PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 SUBJECT: Class II Permissive Charge for FCC ID: 2AJGM-UV82 The product DUAL BAND FM TRANSCEIVER has been granted by FCC dated 06/25/2018, FCC ID: 2AJGM-UV82. Now we, PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP would like to modify the authorized equipment for below changes:

Changed software version from UV82 to UV82III Changed hardware version from UV82-FST8-VER02 to UV82-FST8- VER05 Removed: VR1, U1, L30, L28, L25, L1 Replaced with 2nd source components: C108, C124, C127, C145, C172, C174, C183, C194, C198, C199, C208, C218, L32, CY3 Changed physical position of CY3 incl. appropriate PCB layout adaptation Model name changed from UV-82, UV-82L, GT-5 to UV-82 and UV-82X3 Enabled the US Amateur Radio Band 222 225 MHz (TX) and 200 260 MHz (RX) We would like to certify the additional of certified FCC ID: 2AJGM-UV82 as a Class II Permissive Change in this device. Thank you for your attention in this matter. Signatory Contact Person:Peter Wang Ersteller:

Erstelldatum: 3. August 2001 U. Rodemeier Revision: 00 Datum: 3. August 2001 D:\vera\FCC\\UV-82\data\UV-82_Applicant Letter for modification.doc Seite 1 von 1

PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Jan. 12, 2021 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject: Explanation of differences between product types FCC ID: 2AJGMUV82 Models: UV-82, UV82IC, P82UV, UV82X, UC82 Pro,UV-82 Plus, GT-

5, UV-82HP, Mate82 To Whom It May Concern:

We, The PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY hereby declare that the model : UV82IC, P82UV, UV82X, UC82 Pro,UV-82 Plus, GT-5, UV-82HP, Mate82 is identical with the model : UV-82, except the model name. Except for the different above, no other modification is performed. Sincerely, PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY Signature:

[Peter Wang, General Manager]

PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Jan. 12, 2021 Subject; Request for Confidentiality FCC ID: 2AJGMUV82 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Peter Wang Title: General Manager

PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Jan. 10, 2019 Federal Communication Commission Authorization and Evaluation Division FCC ID: 2AJGM-UV82 Re: Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, the applicant hereby requests confidential treatment of information applied this application as outlined below:

1: Block Diagram 2: Schematics 3: Operational Description 4: Parts List The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rules 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP Contact person: Peter Wang

PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Date: Jan. 12, 2021 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA FCC ID: 2AJGMUV82 Subject: Declaration of compliance to the requirements of 15.121 We declare that, this scanning receiver is incapable of operating (tuning), or readily being altered by the users to operate, within the frequency bands allocated to the Cellular Radiotelephone Service in part 22 of this chapter (cellular telephone bands). This device will not be able to receive transmissions in the cellular telephone bands by means of clipping the leads of, or installing, a simple component such as a diode, resistor or jumper wire; replacing a plug-in semiconductor chip; or programming a semiconductor chip using special access codes or an external device, such as a personal computer. This device is also incapable of converting digital cellular communication transmissions to analog voice audio. This device is designed so that the tuning, control and filtering circuitry is inaccessible. Any attempts to modify the equipment to receive transmissions from the Cellular Radiotelephone Service will render the receiver inoperable. This scanning receiver rejects any signals from the Cellular Radiotelephone Service frequency bands that are 38 dB or lower based upon a 12 dB SINAD measurement. We are aware that the modification of this device to receive transmissions from Cellular Radiotelephone Service frequency bands will be considered to constitute manufacture of such equipment. This includes any individual, individuals, entity or organization that modifies one or more scanners. Any modification to receive transmissions from the Cellular Radiotelephone Service frequency bands voids the certification of the scanning receiver, regardless of the date of manufacture of the original unit. If you have any questions, please feel free to contact me. Thank you. Sincerely, Signatory

[Peter Wang, General Manager]

PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Date: 22 June 2018 PHOENIX TESTLAB GmbH Product Certification Knigswinkel 10 D 32825 Blomberg FCC ID: 2AJGM-UV82 Subject: Declaration of compliance to the requirements of 15.121 We declare that, this scanning receiver is incapable of operating (tuning), or readily being altered by the users to operate, within the frequency bands allocated to the Cellular Radiotelephone Service in part 22 of this chapter (cellular telephone bands). This device will not be able to receive transmissions in the cellular telephone bands by means of clipping the leads of, or installing, a simple component such as a diode, resistor or jumper wire; replacing a plug-in semiconductor chip; or programming a semiconductor chip using special access codes or an external device, such as a personal computer. This device is also incapable of converting digital cellular communication transmissions to analog voice audio. This device is designed so that the tuning, control and filtering circuitry is inaccessible. Any attempts to modify the equipment to receive transmissions from the Cellular Radiotelephone Service will render the receiver inoperable. This scanning receiver rejects any signals from the Cellular Radiotelephone Service frequency bands that are 38 dB or lower based upon a 12 dB SINAD measurement. We are aware that the modification of this device to receive transmissions from Cellular Radiotelephone Service frequency bands will be considered to constitute manufacture of such equipment. This includes any individual, individuals, entity or organization that modifies one or more scanners. Any modification to receive transmissions from the Cellular Radiotelephone Service frequency bands voids the certification of the scanning receiver, regardless of the date of manufacture of the original unit. If you have any questions, please feel free to contact me. Thank you. Sincerely, Signatory PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY Contact person: Peter Wang Title: Manager