Pokit Pro User Manual MODEL: POK-PRO Pokit Innovations Table of Contents Warranty and Limitation of Liability 1 2 3 4 5 6 7 7 9 10 Introduction Contacting Pokit Installing the App Switch Explanation Safety Information Fuse Replacement Technical Specifications Recharging Taking Measurements 10.1 Voltage 10.2 Current 10.3 Resistance/Continuity 10.4 Capacitance 10.5 Diodes 11 12 13 Accessories Ratings Cleaning and Maintenance Troubleshooting 13.1 No BLE Connection 13.2 Poor BLE Connection 13.3 Voltage Measurement 13.4 Low Current Measurement 13.5 High Current Measurement 13.6 Other Measurements 14 15 Getting Started with the App Appendix A. 15.1 Measurement Overvoltage Categories 2 Pokit Innovations 3 3 3 4 4 5 6 6 8 8 8 8 9 9 9 11 12 12 12 12 13 13 13 14 15 15 10 1 Warranty and Limitation of Liability This Pokit product will be free from defects in materials and workmanship under normal use as described in the published product documentation for 12 months from the date of original purchase (Limited Warranty). This Limited Warranty is only valid and enforceable if you have purchased the product directly from Pokit Innovations or our authorised resellers and distribu-
tors. It does not apply where you purchase the product from an unauthorised reseller. The following link contains our complete Limited Warranty and Limitation of Liability:
www.pokitinnovations.com/warranty-policy/
TO THE EXTENT PERMITTED BY LAW, POKIT INNOVATIONS PTY LTD AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PAR-
TICULAR PURPOSE OR ANY SIMILAR STANDARD IMPOSED BY APPLICABLE LEGISLATION AND POKIT INNOVATIONS PTY LTDS RESPONSIBILITY TO REPAIR, REPLACE, OR OFFER A REFUND FOR DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE REMEDY PROVIDED TO ITS CUSTOMERS UNDER THIS WARRANTY To obtain service for your Pokit product, please contact us. 2 Introduction The Pokit Pro (MODEL: POK-PRO) is a battery powered multimeter, oscilloscope and logger. This device meets CAT III IEC61010-1 Edition 3 Standards. IEC61010-1 defines four mea-
surement categories (I to IV) based on the potential danger from transients. CAT III devices are designed to protect against transients when measuring equipment permanently installed in a building. Examples of this kind of equipment are distribution boards, circuit breakers, and mains socket outlets. 3 Contacting Pokit Website: www.pokitinnovations.com Email: support@pokitmeter.com Address:
Pokit Innovations Suite 2.2, 56 Delhi Rd, North Ryde, NSW, 2113 Australia 3 Pokit Innovations 4 Installing the App The Pokit Pro requires a Bluetooth connection to a smartphone running the official Pokit App. No measurements can be taken without the app. Download the Pokit App from the Apple App Store or Google Play Store. For information about device compatibility visit: pokitmeter.com/devices. Ensure the device is charged and press the button once to power on. 1. 2. 3. 4. Open the app and see your devices listed. Connect to your Pokit and start measuring. 5. 5 Switch Explanation Warning: Personal Injury or damage to the Pokit Pro can occur if you attempt to take a mea-
surement with the switch in an incorrect position. Ensure the switch is in the correct position before taking a measurement by adjusting the switch and selecting the desired measurement mode in the app. Measurement modes will not be selectable if the switch is in the wrong position. Resistance / Low Current / Capacitance / Diodes:
Measurement Mode Voltage:
Select this mode for voltage mea-
surements. Select this mode for resistance measurements, current mea-
surements below 300 mA, diode measurement, external tempera-
ture probe use and capacitance measurement. High Current:
Select this mode for high current measurements. Warning: Restrict use to 10A max current for a maximum of 30 seconds every 15 minutes. 4 Pokit Innovations 6 Safety Information Use the device only as specified in this manual. Do not exceed the measurement limits defined in the specifications. Do not use the device if it appears damaged, or if it is not operating properly. Inspect the probe lead, button, switch, USB port and unit for signs of wear before use. The black probe lead is double insulated with a white inner insulation layer. If the white layer is visible then stop using the device immediately. Always use proper switch position and measurement mode for measurements (Refer to Section 5). Turn off circuit power before connecting the device to take a current measurement. Re-
member to connect the device in series with the circuit when measuring current. Do not apply more than the rated voltage (as marked on the device) between terminals, or between any terminal and earth ground. Use caution with voltages above 30V ac rms, 42V ac peak, or 60V dc. These voltages pose a shock hazard. Disconnect circuit power and discharge all high-voltage capacitors before testing resis-
tance, continuity, diodes, or capacitance. Do not use the device in an environment where explosive gas or vapor may be present. Keep your fingers behind the finger guards at all times when measuring with the probes. When measuring mains voltages, only use accessories that are rated with measurement category III or IV ratings for voltages that meet or exceed the rated voltage of the device and are compatible with Pokit Pro. Comply with local and national safety requirements when working in hazardous locations. Use proper protective equipment, as required by local or national authorities, when work-
ing in hazardous areas. Avoid working alone. Do not use device if internal water damage is suspected. Use only the specified replacement fuse or the protection may be impaired and the war-
ranty voided. Verify the devices operation by measuring a known voltage prior to use. Description Symbol Caution -
Consult manual for more information. Equipment protected throughout by double insulation or reinforced insulation. Fuse required - See section 7 of manual for details. 5 Pokit Innovations 7 Fuse replacement Only use the appropriate fuses for Pokit Pro:
Fuse for High Current: 10A, 600V AC/DC FAST 10kA Fuse (PN: 0ADAC9100-BE) Fuse for Low Current: 0.5A, 600V AC/DC FAST 10kA Fuse (PN: 0ADAC0500-BE) Before replacing the fuse ensure the device is removed from any external circuits. 1. Lift external rubber fuse cover. 2. Remove internal fuse cover screw and remove internal fuse cover. 3. Replace blown fuse. 4. Ensure replacement fuse matches the correct ratings as specified on the device. Warning: Ensure all fuse covers are securely in place prior to operation. 8 Technical Specifications Maximum voltage between any terminal and earth ground: 600V Surge Protection 6 kV peak per IEC 61010-1 600V CAT III, Pollution Degree 2 Fuse for High Current: 10A, 600V AC/DC FAST 10kA Fuse (PN: 0ADAC9100-BE) Fuse for Low Current: 0.5A, 600V AC/DC FAST 10kA Fuse (PN: 0ADAC0500-BE) Safety Compliance IEC 61010-1:2010+A1:2016 (Ed 3.0) Safety Compliance IEC 61010-2-033:2012 (Ed 1.0) Maximum Operational Altitude: 2000m 6 Pokit Innovations Characteristic Specification Voltage Current Resistance Temperature Capacitance Diode Continuity Logging Logged Parameters Logging Sample Rate Input Impedance (DC) Operating Temperature Battery Charging Temperature Max Sample Rate BLE Range 1mV to 600V AC(True RMS)/DC 1%
1A to 10A* AC(True RMS)/DC 1%
100m to 1M 1%, 1M to 5M 5%
0 to 60C 1C, 32 to 140F 1.8F 1nF to 1000F 2%
0V-1.5V 100ms, Internal Buzzer 128kB, 3hr/sample @ 6 months Voltage, Current, Temperature 100ms to 18hr 10M All measurements are 3 readings
-10 to 40C, 14 to 104F 10 to 45C, 50 to 113F 1M Samples/sec 10m
*Do not measure Currents above 6A for more than 30 seconds every 15 Minutes. Full specifications are available in the app. EMC Compliance: CE, FCC, RCM, MiC 1.Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. 2.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. Suppliers Declaration of Conformity Pokit Innovations Pty. Ltd. POK-PRO Trade Name:
Model Number:
Responsible Part---U.S. Contact Infomation Company:
Street Address:
City, State:
Zip Code:
Telephone number:
Internet contact infomation:
Pokit Innovations Pty. Ltd. Suite 2.01, 56 Delhi Rd Macquarie Park, NSW 2113
+61 1300 611 388 www.pokitinnovations.com FCC Compliance Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference recieved, including interference that may cause undesired operation. 7 Pokit Innovations 9 Recharging Ensure the device is removed from any external circuits before recharging the device. Do not perform measurements when the device is charging. Included is a USB C cable which can be used to charge your device from any compliant USB-A port. The device should fully recharge in 3 hours or less. 10 Taking Measurements As a safety precaution when working on mains circuits, if possible, isolate circuits before taking measurements. Always wear appropriate PPE safety gear when measuring live circuits. Pokit Pro is Rated for CAT II 600V circuits when no accessories are fitted. To measure CAT III circuits, probe shrouds must be added to the probe tips in order to safeguard from short cir-
cuits as per IEC61010. Some of the accessories are also rated to CAT III and may also be used to measure CAT III circuits (Refer to Section 11). Refer to Appendix A for more info regarding measurement categories. 10.1 Voltage When measuring voltage, make sure the switch is set to voltage measurement. To test the Pokit Pro devices, take a measurement on a known live circuit to ensure the device is operating correctly. Check (or replace) the 0.5A fuse if 0V is measured. Warning: Stop using the device immediately if the fuse is OK and 0V is measured. 10.2 Current When measuring Low Current (<300mA), make sure the switch is set to Low Current mea-
surement. 8 Pokit Innovations When measuring High Current (>300mA), make sure the switch is set to High Current mea-
surement. For Currents above 6A, do not exceed the 30sec/15min rating of the high current mode. After 30 seconds of measurement wait 15 minutes before taking your next reading. The unit may become hot if measurements are taken for longer periods of time. Isolate the circuit to be measured before connecting and disconnecting the Pokit Pro. Do Not connect to a live circuit as this may cause arcing to occur between the Pokit Pro test probes and the circuit contacts. 10.3 Resistance/Continuity When measuring Resistance, make sure the switch is set to Resistance measurement. Warning: Do not connect to Live Mains Voltages in Resistance mode. 10.4 Capacitance When measuring Capacitance, make sure the switch is set to Capacitance measurement. Warning: Do not connect to Live Mains Voltages in Capacitance mode. 9 Pokit Innovations 10.5 Diodes When measuring Diodes, make sure the switch is set to Diode measurement. Do not connect to Live Mains Voltages in Diode measurement mode. See app for detailed measurement instructions. 11 Accessories Ratings WARNING The applicable measurement category and voltage rating for the Pokit Pro and any attached accessories is always the lower of the two. Ensure both the accessory and the Pokit Pro are adequately rated before measurement. 12 Cleaning and Maintenance Dirt or moisture on the probe pins can affect readings. Wipe the device with a damp cloth and mild detergent. Do not use abrasives or solvents. 10 Pokit Innovations 13 Troubleshooting If none of the below troubleshooting tips resolves your issue, visit the Pokit Innovations web-
site for more troubleshooting guides or contact our support team at support@pokitmeter.com. 13.1 No BLE Connection If the Pokit Pro does not appear in the app, then try the following:
Press the button once to wake the Pokit Pro up if it hasnt been used for a while. Move closer to the Pokit Pro (max rated BLE range is 10m). Plug the Pokit Pro into a USB compliant charger; the RGB LED should blink green to indicate a charging state. Try disconnecting other Bluetooth devices from your phone. Refresh the list of connectable devices. Restart the app. Restart the phone. Make sure Bluetooth is enabled on your phone and the Pokit Pro app has its Bluetooth permissions set correctly. 13.2 Poor BLE Connection If the Pokit Pro keeps disconnecting while in use, try the following:
Move closer to the Pokit Pro (max rated BLE range is 10m). Try disconnecting other Bluetooth devices from your phone. Restart the app. Restart the phone. Ambient electrical noise can also cause poor connection. 13.3 Voltage Measurement If the Pokit Pro is not recording a Voltage measurement, try the following:
Make sure the switch is correctly indexed in the Voltage measurement position (refer to section 10.1). Make sure that you have selected the correct measurement mode for the signal i.e., AC for AC Signals such as switchboards, outlets and household appliances and DC for DC Signals such as computer equipment, batteries and logic circuits. If you are unsure, use oscilloscope mode in DC Coupling to determine the signal type. If you have multiple Pokit devices, ensure that you are connected to the correct Pokit Pro. You can flash the RGB indicator by changing devices or by pressing locate in the app. Check the fuse is OK by disconnecting from the circuit you are measuring. Move the switch into Low Current measurement mode, select continuity in the Pokit Pro App and short the probe leads together. If there is no continuity, replace the 500mA fuse (Refer to section 7). If Voltage measurement is not working correctly after troubleshooting, an internal fault may exist, stop using the device immediately. 11 Pokit Innovations 13.4 Low Current Measurement If the Pokit Pro is not recording Low Current measurement , try the following:
Make sure the switch is correctly indexed in the Low Current measurement position (refer to section 10.2). Make sure that you have selected the correct measurement mode for the signal i.e AC for AC Signals such as switchboards, outlets and household appliances and DC for DC Signals such as computer equipment, batteries and logic circuits. If you are unsure, use oscilloscope mode in DC Coupling to determine the signal type. If you have multiple Pokit Pros, ensure that you are connected to the correct Pokit Pro. You can flash the RGB indicator by changing devices or by pressing locate in the app. Check the fuse is OK by disconnecting from the circuit you are measuring. Move the switch into Low Current measurement mode, select continuity in the Pokit Pro App and short the probe leads together. If there is no continuity, replace the 500mA fuse (Refer to section 7). If Low Current measurement is not working correctly after troubleshooting an internal fault may exist. Stop using the device immediately. 13.5 High Current Measurement If the Pokit Pro is not recording High Current measurement , try the following:
Make sure the switch is correctly indexed in the High Current measurement position
(refer to section 10.2). Make sure that you have selected the correct measurement mode for the signal i.e., AC for AC signals such as switchboards, outlets and household appliances and DC for DC Signals such as computer equipment, batteries and logic circuits. If you are unsure, use oscilloscope mode in DC Coupling to determine the signal type. If you have multiple Pokit devices, ensure that you are connected to the correct Pokit Pro. You can flash the RGB indicator by changing devices or by pressing locate in the app. Replace the 10A Fuse (Refer to section 7). If High Current measurement is not working correctly after troubleshooting, an internal fault may exist. Stop using the device immediately. 13.6 Other Measurements If the Pokit Pro is not recording Other measurements, try the following:
Make sure the switch is correctly indexed in the Low Current measurement position (refer to section 10.2). If you have multiple Pokit Pros, ensure that you are connected to the correct Pokit Pro. You can flash the RGB indicator by changing devices or by pressing locate in the app. Check the fuse is OK by disconnecting from the circuit you are measuring. Move the switch into Low Current measurement mode, select continuity in the Pokit Pro App and short the probe leads together. If there is no continuity, replace the 500mA fuse (Refer to section 7). 12 Pokit Innovations 14 Getting Started with the App To get started with the app, navigate to the Apple App store or Google Play store (respective of your device manufacturer) and download the official Pokit App that is compatible with Pokit Pro. When you start the App, you will receive a prompt requesting you to connect your Pokit devices. Once you select Connect your devices, you will receive another prompt requesting permissions for the app to connect to Bluetooth and/or to allow access to your devices location or likewise. In order to use the app, you will need to enable these permissions. Pokit Innova-
tions does not store or transmit any personal location data however, the software modules we use need these permissions to operate correctly. Connect your device by pressing the connect device button. Using the app, select your device by scrolling down the list of devices until you find the one youre looking for. When you select the device, you will be prompted with important safety information relating to the use of the Pokit devices. Make sure you read this carefully before using your device. Once you have connected to a device, press locate. The RGB indicator LED should blink and the buzzer should sound. If it doesnt, you have likely connected to a different device. Press measure to start taking measurements with your Pokit device. 15 Appendix A 15.1 Measurement Overvoltage Categories OVERVOLTAGE CATEGORY l is not used within the context of IEC 61010. It is intended for equipment used to connect to a mains supply for which precautionary measures have been taken to substantially and reliably reduce transient overvoltages to a level where they cannot cause a hazard. OVERVOLTAGE CATEGORY ll is intended for equipment for which power is supplied from the building wiring. It applies to both plug-connected equipment and to permanently connected equipment. OVERVOLTAGE CATEGORY lll is intended for equipment that forms part of a building wiring installation. Such equipment includes socket outlets, fuse panels, and some mains installation control equipment. OVERVOLTAGE CATEGORY lV is for equipment installed at or near the origin of the electrical supply to a building, between the building entrance and the mains distribution board. Such equipment may include electricity tariff meters and primary overcurrent protection devices. 13 Pokit Innovations