FCC ID: 2BBUI-4082137 Wireless remote

Wireless remote instruction Warning If the winch is under load, the winch rope is under tension or the drum is in motion, do not engage or release the clutch Never place the winch remote control where it can be activated when the natural coil, drive, or capstan is not in use Never place a wireless winch remote in a place where it can be activated during installation, natural winding, driving, or servicing of a winch, or when the winch is not in use The wireless function is automatically turned off after 2 minutes without any operation Remote control (4082137) operating voltage 3V, receiver operating voltage 12V. Frequency range 433-434MHz. Operating temperature: -40 to 65 FCC StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.Caution: Any changes or modications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.RF Exposure InformationThe device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. WINCH OUT Winch out button Press down to control the winch out operation Wireless start indicator When the wireless mode is started, the indicator light is on; When the indicator light is on, the indicator light will blink when you press the control button of the remote control WINCH IN Winch in button Press down to control the winch in operation Press and hold for 3 seconds to enable or disable wireless mode Wireless start/close button

Page 1 of 1 FCC ID: 2BBUI-4082137 LABEL AND LOCATION Wireless remote Model: 4082137 FCC ID: 2BBUI-4082137 Label Location Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: webmaster@lcs-cert.com | Web: www.lcs-cert.com Scan code to check authenticity

Polaris Industries Inc. 2100 Hwy55 Medina Minnesota 55340 United States Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2023-7-4 To whom it may concer:

We, Pol

(FCC ID: 2BBUI-4082137) is not covered equipment prohibited from receiving an equipment authorization pursuant to 2.903 of the FCC rules. is Industries Inc. , hereby certify that the equipment for which authorization is sought We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www foc. gov/supplychain/coveredlist) as an entity producing covered equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(b) and (d)(5) and (6). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 DO1 Sincerely, Vaenith blastn Signature Jeremiah Johnstun Engineer Polaris Industries Inc.

Sincerely, Name/Title Company:

Address:

Phone:

Fax:

E-Mail:

Jeremiah Johnstun/Engineer Polaris Industries Inc. 2100 Hwy55 Medina Minnesota 55340 United States

(218) 463-4969 N/A ANNABELLE@LDNB.COM

Polaris Industries Ine. 2100 HwyS5 Medina Minnesota $5340 United States Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2023-7-4 To whom it may concer:

We, the undersigned, hereby authorize Eurofins Product Service GmbH to acton our behaffin all matters relating to applications for equipment authorization FCC ID: 2BBUI-4082137 including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins current valid General Terms and Conditions

(AGB),Testing and Certification Regulations (PZO) which can be viewed on following website www.eurofins de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Vaenith olestun Name/Title: Jeremiah Johnstun/ Engineer Company: Polaris Industries Inc. Address: 2100 Hwy55 Medina Minnesota 55340 United States Phone: (218) 463-4969 Fax: N/A E-Mail: ANNABELLE@LDNB.COM

Polaris Industries Inc Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 U.S. Agent Designation 6/28/23 Polaris Industries Inc acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2BBUI-4082137):

Name and company of U.S. agent:

Polaris Industries Inc Physical U.S. address of agent:

2100 Hwy55, Medina, MN 55340, United States FRN of U.S. agent:

0033938424 Email address of U.S. agent:

ANNABELLE@LDNB.COM Polaris Industries Inc acknowledges their obligation to accept service of process on behalf of Polaris Industries Inc. Polaris Industries Inc with the FRN 0033938424 accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-

related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature Jeremiah Johnstun Engineer Polaris Industries Inc Signature Jeremiah Johnstun Engineer Polaris Industries Inc 5 0 V

, U

) 7

) d

1 1 9 2 _ t n e g A _ S U

l e d o m

_ 8 4