PRODUCT SPECIFICATION DECT application module Model no.: KT4586 POLYCOM ED 2.0 DATE 29-06-2011 SIGN HBR Page 1 of 12 Model no.: KT4586 141993XX-DS PRODUCT SPECIFICATION 1. 2. 3. 4. Preface ....................................................................................................................................... 3 Features ..................................................................................................................................... 3 Circuit description ..................................................................................................................... 4 Pin configuration .................................................................................................................... 5 5. Mechanical dimension............................................................................................................ 7 PCB integration & soldering ................................................................................................. 8 FCC compliance statement .................................................................................................. 11 Safety compliance statement .............................................................................................. 12 6. 7. 8. Proprietary and Confidential The information contained herein is the sole intellectual property of Polycom, Inc. No distribution, reproduction or unauthorized use of these materials is permitted without the expressed written consent of Polycom, Inc. Information contained herein is subject to change without notice and does not represent commitment of any type on the part of Polycom, Inc. Polycom and Accord are registered trademarks of Polycom, Inc. Notice While reasonable effort was made to ensure that the information in this document was complete and accurate at the time of printing, Polycom, Inc., cannot assume responsibility for any errors. Changes and/or corrections to the information contained in this document may be incorporated into future issues. POLYCOM ED 2.0 DATE 29-06-2011 SIGN HBR Page 2 of 12 Model no.: KT4586 141993XX-DS PRODUCT SPECIFICATION 1. Preface The KT4586, DECT application module is used to transfer messaging, data, and voice signals by use of the radio frequency spectrum according to the DECT standard. KT4586 is a fully approved module that complies with the following standards and certifications:
EN 301 406 V2.1.1:2009-07 (DECT radio) EN 300 175-1 to 8 (DECT CI) EN 301 489-1 V1.8.1:2008-04, EN 301 489-6 V1.3.1:2008-08 (EMC) IEC 60950-1:2005 (ed. 2.0) +am1:2009, EN 60950-1:2006+A11:2009+A1:2010 (Safety) R&TTE certificate FCC PART 15, Subpart D FCC part 15B FCC SAR RSS-213 This means that by integration on a main board no radio test is required. 1880 1930 MHz 60(EU) 30(US) logical duplex channels. Typ.< -93 dBm [BER,1000 ppm]. Typ. 23 dBm. , 20.2 dBm (US) 2.0 3.45V TBD
-20C to +60C. 25.0 X 30.0 X 3.0mm. See data sheet for SC14441 2. Features RF range:
DECT channels:
Receiver sensitivity:
Transmit power (NTP):
Power supply range:
Current consumption:
Temp. Range:
Size:
Other features:
POLYCOM ED 2.0 DATE 29-06-2011 SIGN HBR Page 3 of 12 Model no.: KT4586 141993XX-DS PRODUCT SPECIFICATION 3. Circuit description The module consists mainly of the fully integrated CMOS transceiver and baseband processor SC14441 from SiTel semiconductor intended for DECT 6.0 handsets and base stations. RF switches and other components are added to the design in order to perform the desired functionality required for DECT/GAP. Figure 1 shows the block diagram of the module. Ant. SW T/R SW TX Balun RX Balun SC14441 Integrated CMOS transceiver and baseband processor Figure 1 DC-DC converter ports ULP controle ports Quad SPI bus 29 general purpose I/O ports Serial debug interface UART, Full duplex SPI interface Dual ACCESS bus PCM interface 16-bit linear audio CODEC Analog microphone interface. Analog loudspeaker interface. Charge controle To supply LDO & PWR SW circuit QSPI FLASH EEPROM The DECT transceiver/baseband SC14441 SC14441 is a 1.8V single chip for DECT applications containing a fully integrated radio transceiver and baseband processor. It is designed to perform the complete transmit and receiver function. The device is designed to operate the frequency synthesizer in a close loop configuration both during transmit and receive mode. Logic output ports are used to control the T/R switch and antenna switch for FAD (Fast Antenna Diversity). The CompactRISC CR 16Cplus microprocessor with a single wire debug port running from ROM controls the protocol stack and the I/O peripherals, keyboard, UART, ACCESS bus, SPI, LED drivers and RF switches. The audio path comprises a 16 bit CODEC with an analog frontend including a high efficiency 4 ohm audio amplifier (class D) and a programmable Gen2DSP supporting various telecommunication algorithms. Detailed information about the chip is available from SiTel semiconductor. POLYCOM ED 2.0 DATE 29-06-2011 SIGN HBR Page 4 of 12 Model no.: KT4586 141993XX-DS PRODUCT SPECIFICATION 4. Pin configuration A1 A2 A3 A4 A5 A6 A7 A8 A9 GND GND GND CP_VOUT2 VDDIO P12 GND GND VBAT B1 B2 B3 B4 B5 B6 B7 B8 B9 GND GND C1 C2 GND P30 CP_VOUT1 C3 GND P15 GND P26 P05 GND P01 C4 C5 C6 C7 C8 C9 P27 P14 P11 GND P00 GND D1 D2 D3 D4 D5 D6 D7 D8 D9 GND P31 P16 P17 GND GND GND GND P24 E1 E2 E3 E4 E5 E6 E7 E8 E9 VDDPA GND F1 F2 SOCp P10 CHARGE_CTRL F3 ADC2 SOCn GND GND GND GND GND F4 F5 F6 F7 F8 F9 DC_CTRLN ULP_PORT ULP_VBAT ULP_MAIN_CTRL RFP0n P23 A10 P04 B10 VBATT C10 JTAG D10 VDD E10 P07 A11 RSTn B11 GND C11 VCCRF D11 P25 E11 GND B12 TP2 VREFm LSRp P37 J1 J2 J3 GND MICh GND ONE_CELL J4 P35 DC_SENCE J5 GND K1 K2 K3 K4 K5 VREFp MICp L1 L2 P32_CIDINp L3 P36 P34 LDORF_CTRL H8 RFP2 DC_I P22 H9 GND H10 GND H11 GND J6 J7 J8 J9 RFP1 K6 WLED0 GND P21 GND K7 WLED1 K8 K9 P20 GND J10 GND K10 RF0 J11 GND K11 RF2 GND LSRn GND P33 GND DC_CTRL GND H1 H2 H3 H4 H5 H6 H7 G1 G2 G3 G4 G5 G6 G7 G8 G9 GND G10 GND G11 GND GND MICn GND GND RFP0 GND GND L4 L5 L6 L7 L8 WLED2 L9 GND L10 RF1 L11 GND F10 P13 F11 P06 M2 TP1 Leave K10, K11, L10, M2 and B12 (RF ports and test pins) unconnected to the main board without any conducting plan underneath. Connect VREFm to local GND on the main board. POLYCOM ED 2.0 DATE 29-06-2011 SIGN HBR Page 5 of 12 Model no.: KT4586 141993XX-DS PRODUCT SPECIFICATION Top view of the pins POLYCOM ED 2.0 DATE 29-06-2011 SIGN HBR Page 6 of 12 Model no.: KT4586 141993XX-DS PRODUCT SPECIFICATION 5. Mechanical dimension POLYCOM ED 2.0 DATE 29-06-2011 SIGN HBR Page 7 of 12 Model no.: KT4586 141993XX-DS PRODUCT SPECIFICATION 6. PCB integration & soldering Recommended integration on the main PCB In order to ensure proper coverage and to avoid detuning of the antennas, it is very important to place the module in a free prober way on the main board and in relation to other surrounding materials. As a thumb rule, keep a distance of at least 10 mm from the antenna element to conducting objects and at least 5 mm to non-conducting objects - depending of the size. Keep in mind that electrical shielding objects, even partly surrounding the antennas, will normally cause a significant degradation of the coverage. Place the module at the corner of the main-board as shown below. If the module has to be placed away from the edge of the main-board, then avoid conducting areas in front of the antennas and make a cut-out in the main board underneath the antennas as shown below. Keep solid ground on layer 2 out to the edges of the main board as shown. POLYCOM ED 2.0 DATE 29-06-2011 SIGN HBR Page 8 of 12 Model no.: KT4586 141993XX-DS PRODUCT SPECIFICATION Recommended copper pad and solder mask opening (NSMD) Cu. pad 0,80x0,80mm Solder mask opening 1,00x1,00mm Recommended stencil design
(stencil thickness 0.122 mm) Opening in stencil 1,12x1,12mm POLYCOM ED 2.0 DATE 29-06-2011 SIGN HBR Page 9 of 12 Model no.: KT4586 141993XX-DS Cu. pad 1.00x1.00mmSolder mask opening 1.80x1.80mmSubstrateCopper padsSolder MaskStencilOpening in stencil 1.40 x 1,40mm Reflow profile leadfree Sn96.5-Ag3.0-Cu0.5 t3 t4 Meltingpoint 217C 200 250 Temp. C T3 220C T2 190C PRODUCT SPECIFICATION Recommended re-flow profile T1 Preheat zone bottom T2 Preheat zone top T3 Reflow zone T1 150C 150 100 50 0 t1 t1: Max. Change in temperature t2: Time in preheat (150C < temp. < 190C) t3: Time in reflow zone (temp. > 220C) t4: Peak temperature t2 3C/sec. 60 - 120 sec. 30 - 60 sec. 237C5C 150C 190C 220C Time We recommend to fabricate PCB in accordance with IPC-A-600G, IPC-6012B, IPC-
6016/A and IPC-6018A, Class 2; per IPC-6011 using customer supplied data files. POLYCOM ED 2.0 DATE 29-06-2011 SIGN HBR Page 10 of 12 Model no.: KT4586 141993XX-DS PRODUCT SPECIFICATION 7. FCC compliance statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Information to User:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC / IC Canada Labeling of host device:
The modular transmitter is labeled with its own FCC and IC identification number, and, if the FCC or IC identification numbers are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label shall use wording as the following: Contains FCC ID:
M72-PK4586 and Contains IC: 1849C-PK4586. RF Exposure information:
The internal antennas used for this mobile transmitter must provide a separation distance of at least 20 cm from all persons. OEM integrators and end users must be provided with transmitter operating conditions for satisfying RF exposure compliance. Antenna information:
The module has been tested and approved for use with the antenna listed below:
Type of antennas:
Gain of the antennas:
Frequency range:
The use of that module in combination with a not listed antenna must be authorized with respective regulatory agencies. PCB monopole antenna. 1.2 dBi 1920-1930 MHz POLYCOM ED 2.0 DATE 29-06-2011 SIGN HBR Page 11 of 12 Model no.: KT4586 141993XX-DS PRODUCT SPECIFICATION 8. Safety compliance statement 1) The specific external power supply for the DECT application module KT4585A has to fulfil the requirements according to clause 2.5 (Limited power source) of this standard EN 60950-
1:2006. 2) Interconnection circuits shall be selected to provide continued conformance to the requirements of clause 2.2 for SELV (Safety Extra Low Voltage) circuits according to EN 60950-1:2006 after making connections. 3) Interface type not subjected to over voltages (i.e. does not leave the building). 4) Requirements additional to those specified in this standard may be necessary for:
- Equipment intended for operation in special environments (for example, extremes of temperature, excessive dust, moisture or vibration, flammable gases and corrosive or explosive atmospheres).
- Equipment intended to be used in vehicles, on board ships or aircraft, in tropical countries or at altitudes grater than 2000 m.
- Equipment intended for use where ingress of water is possible. 5) Installation by qualified personnel only!
6) The product is a component intended for installation and use in complete equipment. The final acceptance of the component is dependent upon its installation and use in complete equipment. POLYCOM ED 2.0 DATE 29-06-2011 SIGN HBR Page 12 of 12 Model no.: KT4586 141993XX-DS