FCC ID: 2APJZ-TBC003R Controller

smart LED light strings Wrapped Dome Straight Lights INSTRUCTIONS GUIDE FOR INDOOR AND OUTDOOR USE warning READ AND KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE IMPORTANT SAFETY INSTRUCTIONS When using electrical products, basic precautions should always be followed including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS. 1. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When used outdoors, this product must be connected to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualied electrician for proper installation. 2. This seasonal use product is not intended for permanent installation or use. 3. Do not mount or place near gas or electric heaters, replace, candles or other similar sources of heat. 4. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails. 5. Do not let lamps rest on the supply cord or on any wires. 6. Disconnect the product from power source when leaving the house, when retiring for the night, or if left unattended. 7. This is an electric product - not a toy! To avoid risk of re, burns, personal injury and electric shock, KEEP PRODUCT OUT OF REACH OF SMALL CHILDREN!

8. Do not use this product for other than its intended use. 9. Do not hang ornaments or other objects from cord, wire, or light string. 10. Do not close doors or windows on the product or extension cords as this may damage the wire insulation. 11. Do not cover the product with cloth, paper or any materials not part of the product when in use. 12. The supply cord, adapter, plugs and/or connectors can not be replaced or modied. If either is damaged, the product should be scrapped. 13. Strobe lights have been known to trigger seizures in people with photosensitive epilepsy. 14. The controller and remote controller (if included) can only be used with this product. 15. Read and follow all instructions that are provided with the product. SAVE THESE INSTRUCTIONS. WARNING: This product may potentially trigger seizures for people with photosensitive epilepsy when using the motion eect light modes. 2 CAUTION 1. To reduce the risk of re or electric shock:

Do not install on trees with needles, leaves or branches covering any metal materials;

Do not mount or support cords or cables in a manner that can cut or damage wire insulation;

Do not attempt to replace lamps or modify string;

Use only the adapter provided with this product, This product does not contain lamp shunts. 2. Make sure connectors are fully inserted and secured. Twist all connector rings until hand tight. 3. Some Twinkly light sets (models dependable) allow multiple strings setup. To avoid the risk of re or personal injury, do NOT exceed the maximum wattage capacity of adapter. Refer to the "Maximum Light Strings can be Connected" column in the Technical Specications table for more details. 4. When not in use, store the product in a cool, dry place away from sunlight. are brown or break o easily. Keep the tree holder lled with water. 6. If the product is placed on a tree, the tree should be well secured and stable. 5. When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place on live trees in which the needles 7. Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire insulation or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire. 8. When storing the product, carefully remove the product from wherever it is placed, including trees, branches, or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires. Information Decoration lighting, not suitable for household illumination. The crossed-out wheeled bin symbol indicates that the item should be disposed of separately from household waste. The item should be handed in for recycling in accordance with local environmental regulations for waste disposal. Caution Warning This is a class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures! Do not connect the chain to the supply while it is in the packing. Do not connect parts of this light chain to those of another manufacturer. NON-REPLACEABLE BULB. Built-in LED light source. The connecting cable cannot be repaired or replaced. If the cable is damaged, the entire tting must be discarded. Danger! Strangulation hazard. Hang out of reach of young children. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 3 Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution:

IMPORTANT NOTE:

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. ISEDC Warning This device complies with Innovation, Science, and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1)this device may not cause interference, and

(2)this device must accept any interference, including interference that may cause undesired operation of the device.

(1) l'appareil nedoit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. The device is compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance.The minimum distance from body to use the device is 20cm. Le prsent appareil est conforme Aprs examen de ce matriel aux conformit ou aux limites dintensit de champ RF, les utilisateurs peuvent sur l exposition aux radiofrquences et la conformit and compliance dacqurir les informations correspondantes. La distance minimale du corps utiliser le dispositif est de 20cm Le prsent appareil est conforme aux CNR d' Innovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :

Le prsent appareil est conforme aux CNR d' Innovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) l'appareil nedoit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. The device is compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance.The minimum distance from body to use the device is 20cm. The device has been tested and comply with ISEDC SAR limits. L'appareil a t test et est conforme aux restrictions ISEDC SAR. Le prsent appareil est conforme Aprs examen de ce matriel aux conformit ou aux limites dintensit de champ RF, les utilisateurs peuvent sur lexposition aux radiofrquences et la conformit and compliance dacqurir les informations correspondantes. La distance minimale du corps utiliser le dispositif est de 20cm. single string setup Adapter Controller Add-on Connector 1. 2.

* Product outlook varies by models. Add-on Connector only available in specic models. 1. Connect the Twinkly light string to the power adapter. 2. Plug the power adapter into a power socket and the lights will switch on. 6 multiple strings setup 2.

* Images for reference only Open the cap 4. 1. 3. 1. Refer to the "Maximum Light Strings can be Connected" column in the Technical Specications table to conrm if your light set model allows multiple strings setup. Do not attempt multiple light strings setup if N/A is marked. Make sure the total rated wattage of all connected products does not exceed the maximum wattage capacity of a single product. 2. Remove the adapter (and the extension cord as you need) of the rst string and save for future use. 3. Plug the add-on connector of the second string to the controller connector of the rst string. 4. Decorate your desired spot and plug it in. 7 controller CONTINUOUS GREEN: Direct Wi-Fi mode, connected FLASHING GREEN: Direct Wi-Fi mode, no device connected CONTINUOUS BLUE: Home Wi-Fi network mode, connected FLASHING BLUE: Home Wi-Fi network mode, connection in progress FLASHING RED: Home Wi-Fi network mode, unable to connect LIGHT BLUE: SETUP MODE (Bluetooth ON) YELLOW: Firmware Update in progress CONTINUOUS RED: General error FLASHING WHITE: Reset procedure in progress BUTTON LED INDICATOR 8 preset effects RAINBOW SNOW UPDOWN FIREWORKS GLOW Light arrangements vary by models Twinkly comes with 5 preset eects that may be used without downloading the app. Simply plug in the light string to a power outlet, then press the button on the controller to switch between the 5 preset eects. 9 app download & setup twinkly 1. 2. 3. 4. Twinkly Choose your controller Generation I Generation II 1. Go to App Store/Google Play Store (or scan QR code). 2. Download and install the Twinkly app. 3. Launch Twinkly app. 4. Select GENERATION II controller for your lights. Follow the setup process on the app. Note: All app illustrations in this document are a mere representation of the functionality and may vary from the actual app visuals. 10 connection modes Bluetooth 5 sec Bluetooth Connecting... A. HOME WI-FI NETWORK CONNECTION B. DIRECT Wi-Fi CONNECTION Twinkly uses Bluetooth for the setup process only. Wi-Fi connection is required for operation. You can use:

A. Home Wi-Fi network connection (recommended):

Connect with your home/oce WiFi from the list of available networks. B. Direct Wi-Fi connection:

Select Twinkly_xxxxxx WiFi from the list of available networks. Password:

Twinkly2019

(NOTE: the internet on your phone will not be available in this case) 11 mapping Mapping complete MAPPING Map the layout of your decoration to unlock the full potential of your Twinkly lights like advanced eects, drawing and many upcoming features. 12 mapping tips Note: For best results, avoid reective surfaces behind the tree, keep the mobile camera steady during the process and ensure a moderate ambient light (not too dark). 13 online manual Browse, play and edit effects Gallery Create new effects Group multiple devices together Download new effects 14 choose preset effects 1. 2. 3. 4. Lights All Favorites Snow Rainbow Snake Bright Twinkle Fireworks Candy Cane Sparkles Horizontal Flag Vertical Flag SNOW E D I T A P P L Y E D I T A P P L Y E D I T A P P L Y 1. Open the Eects Gallery. 2. Select the desired eect to see the real-time preview on your Twinkly set-up. 3. Swipe left or right to browse eect. 4. Tap Apply to store the eect and play continuously. Note: App user interface may change due to technical updates and improvements. 15 troubleshooting Q THE LIGHTS DO NOT SWITCH ON Check that the power adapter is plugged in and that the controller is correctly connected to the device Check that the LED status indicator on the controller is lit Briey press the button on the controller If this doesnt work, unplug the power adapter, wait 30 seconds and plug in again Q TWINKLY SETUP WAS SUCCESSFUL, BUT THE LIGHTS DONT RESPOND TO COMMANDS Within the Twinkly application, open Devices and check that the Twinkly device is selected If this does not work, stop the Twinkly application and launch it again If this does not work, try to Reset (see Reset procedure below) If this does not work, delete the Twinkly application from your smartphone, then download the latest version from AppStore or Google Play Store Q THE LED INDICATOR IS LIGHT BLUE, BUT MY SMARTPHONE CANNOT FIND TWINKLY Unplug the power adapter, wait 30 seconds, plug it in again and repeat Conguration procedure If this does not work, try to Reset (see Reset procedure below) Q HOW CAN I CONNECT TWINKLY WITHOUT HOME WI-FI NETWORK?

Open Wi-Fi settings on your smartphone Find and select Twinkly_XXXXXX network Enter the Wi-Fi password Twinkly2019 and ensure that the Twinkly_XXXXXX network is connected Q THE LIGHTS TURNED ON BUT LIGHT EFEECTS ARE FROZEN. Briey press the button on the controller If this does not work, unplug the power adapter, wait 30 seconds and plug it in again If you need any assistance, email us at warranty@polygroup.com 16 reset twinkly 2. 1. 3. RED 1. Unplug Twinkly from the power socket. Press and hold the controller button. 2. While holding the button, plug in Twinkly. 3. Keep holding the button until all LEDs turn red, then release the button. 17 Polygroup Trading Limited Unit 606, 6th Floor, Fairmont House, No.8 Cotton Tree Drive, Central, Hong Kong To know more about your twinkly and its other cool features, please visit:

www.polygroup.com/twinkly

Shenzhen Accurate Technology Co., Ltd. Project No.: SZNS220113-01839E-RF FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925) LABEL AND LOCATION Page 1 of 1

Polygroup Trading Limited Unit 606,Fairmont House, 8 Cotton Tree Drive, Central, Hong Kong, China Tel: (852)35832222 Fax: (852)35832288 Email: Daniel.liu@polygroup.com FCC Confidential Authorization Date: 2022-03-08 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2APJZ-TBC003R In accordance with Sections 0.457 and 0.459 of the Commissions Rules, Polygroup Trading Limited,hereby requests long-term confidential treatment of information accompanying this application as outlined below:

The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Block Diagram Schematics Operation Description Sincerely Yours, Signature:

Daniel Liu Compliance manager

Polygroup Trading Limited Unit 606,Fairmont House, 8 Cotton Tree Drive, Central, Hong Kong, China Tel: (852)35832222 Fax: (852)35832288 Email: Daniel.liu@polygroup.com FCC Authorization Date: 2022-03-08 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern:

We Polygroup Trading Limited, the undersigned, hereby authorizes Shenzhen Accurate Technology Co., Ltd. to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Shenzhen Accurate Technology Co., Ltd. on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, This authorization is valid until further written notice from the applicant. 21 U.S.C. 862. Sincerely Yours, Signature:

Daniel Liu Compliance manager QA-FR-170-B 7/29/2014