TM90 MUser Manual Positioning Universal FJ1000MV TL Contents 1 Introductio FJ1000MV TL 1.1 ID and Tooling Design Dimensions: 92mm*50mm*1 8mm 2.1Physical and Electrical Specifications Input Voltage: 7-36VDC Power consumption:
- Active mode: 100mA @12VDC
- Sleep mode: <5mA @12VDC Operating temperature: -30C to 80C Storage temperature: -30Cto 80C 2.2Input/Output Download and debug port: 1 SWDInterface: 1 Function LEDs: 2 GPS Status Green Cellular StatusOrange Buzzer:1 Input:1 Output:1 2.3 Cellular Communication Operation mode : LTE/GPS Operation band : LTEB2/B4/B12/B13/B25,GPS 1.57542GHz Modulation: QPSK/16QAM 2.4 Harnesses There are 1harnesses that may be used with the TM90M-A4:
1. 4 wire power and I/O harness 2.5 Event Codes The table below relates the Event codes in the message to the reason the message was generated:
Message # Message Type Description 0 Interval Auto Report (auto report when moving) 1 Vibration Vibration alarm(report when GPS is OFF and vibration detected) 2 Power Disconnect Power cut alarm (report when external power is cut off) 3 Power Connect Power connected alarm (external power has been connected) 4 Ignition ON Hardwired or Virtual Ignition ON detected
| fo FJ1000MV Sk 5 Ignition OFF Hardwired or Virtual Ignition OFF detected 6 Input High Input high alarm 7 Input Low Input low alarm 8 9 10 11 12 2.6 System network structure GPS alarm is currently the most advanced security Settings. GPS alarm more expensive t han ordinary burglar alarm, and need to pay the additional service fee, so the popularity i s not high. And alarm is based on a GPRS network communication network, combining with the intelligent linkage of mobile phone and car anti-theft, this kind of alarm alarm is not restricted by distance, overlay network is wide, but need to pay the monthly rental. B uying guide to edit GPS alarm when the choose and buy, need to pay attention to is the c omparison of several common GPS performance. 2.7 Appearance and installation instructions 3.1 Introduction. This chapter is user manual for TM90M. FJ1000MV LL 3.2 List. 1.three TM90M devices. 2.0ne DC 12V cable. FJ1000MV Le 3.3 Description. 3.3.1 Connect theDC 12V cabletotheconnector of J101 onthe device, the other si de connect to DC 12V, you can use the DC 12v cable to supply power. ar i a
3.3.2 7 T FJ1000MV FCC Regulations:
@ This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interf erence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
@ This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits ar e designed to provide reasonable protection against harmful interference i na residential installation. This equipment generates, uses and can radiat e radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particul ar installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one
| 1 FJ1000MV TL or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to w hich the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help.
@ Changes or modifications not expressly approved by the manufacturer cou Id void the user's authority to operate the equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an u ncontrolled environment. To comply with FCC RF Exposure compliance require ments, this grant is applicable to only Mobile Configurations. The antennas us ed for the transmitter must be installed to provide a separation distance of at |
east 20cm from all persons and must not be co-located or operating in conjun ction with any other antenna or transmitter.