Flex OBD-II (FT2200MA) 1 Key Value Proposition Capabilities Simple Install Latest LTE Cat M and NB-IoT technology Flexible and fully featured Applications Car & Light Truck Private Fleets o Utilization o Fuel management Electronic driver logging o o Driver behavior monitoring / coaching o Maintenance monitoring o Dispatching & route optimization Usage Based Insurance (Consumer) Rental and Leased Fleets FLEX CONFIDENTIAL DO NOT DISCLOSE Real-time GPS tracking Impact detection & recording Driver behavior monitoring Driver identification Vehicle identification Standard engine trouble codes Relay control (starter disable) Device removal detection (w/ optional battery) Buzzer (optional) Flex OBD-II (FT2200MA) Specs Dimensions 65mm x 46mm x 24.5mm Weight 54g without battery (0.119 lbs) 59g with battery (0.13 lbs) FLEX CONFIDENTIAL DO NOT DISCLOSE Location GPS (multi-constellation) Multi-tower cellular (via cloud) Assisted acquisition: 2s (via cloud) Hot Start: <2s Acquisition Sensitivity: -160dBm (1) Tracking Sensitivity: -167dBm (2) OBD-II CAN ISO-15765, CAN J1939, CAN 2.0 ISO-9141-2 (for Tachometer) Power Input 6 - 24V (48V OVP) Power Consumption 1.2mA (sleep) - 70mA (peak) @ 12V Sensors Accelerometer & Gyro Flash Memory 16Mb Sensor Sampling Interval 1s to 24hr; cloud configurable Dynamic on motion Reporting Interval 1 min to 24 hour; cloud configurable Dynamic on motion Battery Lithium-Ion 220 mAh
(1) (2) Based on GPS chipset specification
(4) (5) Inside operating temperature range Global Cellular Connectivity 4G (Cat M/NB-IoT) Global Bands 2G: 850,900,1800,1900 Antenna SKUs: AT&T, Verizon, Telstra, EU Local Wireless BLE Operating Temperature On vehicle power: -40C 70C*
On battery power: -5C 60C*
Shock and Vibration SAE J1455 (4) Housing UL94-V0 Flame Retardant Security Secure boot TLS/SSL Certifications RoHS, FCC, CE, IC, UL, REACH, RCM, PTCRB, AT&T, Verizon, Telstra, Applicable carriers. I/O Status LEDs: GPS, Cellular, Power 8-pin connector:
TTL Serial 1 General purpose digital input 2 General purpose digital output/relay controller 1-Wire Technology 5V power output (2A max) Buzzer d'exposition aux frquences radio de la CNR-102, la proximit humaine l'antenne ne doit pas tre infrieure FCC Regulations:
Le prsent appareil est conforme This device complies with part 15 of the FCC Rules. Operation is subject to the following two aux CNR Innovation, Sciences et conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Dveloppement conomique This device has been tested and found to comply with the limits for a Class B digital device, Canada applicables aux appareils pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection radio exempts de licence. against harmful interference in a residential installation. This equipment generates, uses and can L'exploitation est autorise aux radiated radio frequency energy and, if not installed and used in accordance with the instructions, deux conditions suivantes:
may cause harmful interference to radio communications. However, there is no guarantee that
(1) l'appareil ne doit pas produire interference will not occur in a particular installation If this equipment does cause harmful de brouillage, et interference to radio or television reception, which can be determined by turning the equipment off
(2) l'utilisateur de l'appareil doit and on, the user is encouraged to try to correct the interference by one or more of the following accepter tout brouillage measures:
radiolectrique subi, mme si le
-Reorient or relocate the receiving antenna. brouillage est susceptible d'en
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is This device complies with the connected. Canadian ICES-003 Class B
-Consult the dealer or an experienced radio/TV technician for help. specifications. CAN ICES-003(B)/
Caution: Changes or modifications not expressly approved by the party responsible for NMB-003(B) compliance could void the users authority to operate the equipment. RF Exposure Information ISED RF Exposure This device meets the governments requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio Statement frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. This device complies with ISED RSS-102 RF exposure limits set This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. forth for an uncontrolled In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human environment. In order to avoid the proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. possibility of exceeding the IC RSS-102 RF exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. Cet appareil est conforme aux limites d'exposition aux rayonnements de la CNR-102 dfinies pour un environnement non contrl. Afin d'viter la possibilit de dpasser les limites This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device. ISED Notice