FJ1100L User Manual FJ1100L User Manual R1.1 Author jinyi Revision Changes 1.1 Initial version Date 2018-01-03 FJ1100L User Manual Contents Introduction .................................................................................................................. 3 1 ID and Tooling Design ...................................................................................................................... 3 2 Hardware ............................................................................................................................. 4 3 Physical and Electrical Specifications ................................................................ 4 Input/Output .................................................................................................... 4 Cellular Communication.................................................................................... 4 GPS Specification .............................................................................................. 4 Harnesses .......................................................................................................... 5 Hardware Introduction ..................................................................................... 6 Basic RF Performance ....................................................................................... 7 Safety ....................................................................................................................... 7 Software Features ............................................................................................................... 8 Basic Software................................................................................................... 8 Power Modes .................................................................................................... 9 Reset ........................................................................................................................ 9 Test Method ...................................................................................................... 9 Hardware .......................................................................................................... 9 Software Test ...................................................................................................................... 9 4 Event codes ................................................................................................................... 9 FCC Regulations .................................................................................................................... 11 FJ1100L User Manual Introduction 1 The FJ1100L is a vehicle tracking device that uses a GPS satellite receiver to determine location information and a CAT-1 transceiver to communicate information to and from a land based server. In addition, the FJ1100L has several Inputs that may be configured to detect states of sensors and Outputs that can control accessories. The FJ1100L is powered by standard vehicle power (12V or 24V). It accepts several harnesses: a 2 wire power harness, and 4 wire IO harness. Communications between the FJ1100L and the server are carried out using the UDP protocol with sequence acknowledgment messages to confirm receipt of messages by the server. Configuration of the device can be conducted using serial communications over the USB port or by sending SMS messages to the device. ID and Tooling Design The housing will be provided by customer. The product appearance is shown as follows:
Item Dimension Weight Definition 103mm *53mm *18.65mm
/
FJ1100L User Manual 2. Hardware Physical and Electrical Specifications Dimensions: 103mm *53mm *18.65mm Weight: 74.5 g (with optional battery) Input Voltage: 4-36VDC Power consumption:
- Active mode: 200mA 12VDC
- Sleep mode: <2mA 12VDC Operating temperature: -30 to 75 Storage temperature: -40to 85 Input/Output Digital Inputs: 1 Relay driver Outputs: 1 Function LEDs: 2 GPS Status GREEN Cellular Status ORANGE Cellular Communication Operation Mode:
FDD_LTE(Cat1) Operation Band Lte_B4, Lte_B13 Modulation: Uplink:QPSK Downlink: QPSK/16QAM 2.5 GPS Specification 167dBm Tracking Sensitivity Location Technology(72 channel GPS) Location Accuracy (2 meter CEP50) FJ1100L User Manual Harnesses There are1 harnesses that may be used with the FJ1100L:
1. 4 wire power and I/O harness The picture above shows the 4 wire power and I/O harness. The wiring details are:
Power and I/O Harness 4 wires 1. Black V- is connected to Negative or Ground 2. Red V+
is connected to Positive , +12VDC or +24VDC 3. YellowInput0 is an input biased high, negative trigger. 4. White Output 0 is an output, open collector, may be used for Starter Disable. FJ1100L User Manual Hardware features The FJ1100L provides support for specialized hardware features through extended AT commands. The features supported include the following. GPS The major functionality of the GPS module is to compute the correlation results between the incoming signal and the selected PRN code based on certain Carrier Doppler Frequency, Code Doppler Frequency, code phase, carrier phase, and the particular satellite the module is tracking or acquiring. GPIO Two GPIO pins, GP1 and GP2, are presented to the external environment on the main connector. They are general purpose bidirectional lines capable of providing system interrupts to generate a report or drive logic levels to external devices. These pins default to input. GP1 is pulled down representing 0 when disconnected; GP2 is pulled up representing logical 1 when disconnected. They should be asserted to a known value if used. GP1 is intended to use for Ignition Sensing. LEDs Two LED status indicators are provided to verify correct installation and operation. The status LEDs are color coded and directly convey the status of the CAT-1 and GPS subsystems as described in the table below. Their valid operation also indicates operational status and power. LED GREEN Function GPS ORANG E CAT_1 Status On: GPS satellites acquired and Locked Flash Slow: GPS satellite search is in progress Off: No power or GPS subsystem fault On: Indicates CAT_1 connection is made Flash Slow: CAT_1 subsystem initialized but no connection Flash Fast: CAT_1 process Off: No power or CAT_1 subsystem fault initialization in The device provides user control allowing the LEDs to be extinguished once installation is verified. This feature reduces power and further conceals the device Tracker from untrained parties wishing to defeat its operation. Battery Monitor The battery monitor is internal analog input scaled such that the DC value of the power input pin to the device system is measured. This value is scaled to span the most significant 8 bits of the A/D and consequently covers a scale from 0 to 25.5 Volts. FJ1100L User Manual Timers Timers resident on the CAT-1 baseband chip generate periodic interrupts for power down wakeup, watchdog support, report generation and other timer related functions. Report timers are supported by related AT command and cause generation of periodic reports. Motion Detect A factory populates option for motion detector is provided. If populated at the time the FJ1100L is manufactured, this option will work with firmware power down options to keep the FJ1100L in a very low power down state until motion is detected. Upon wakening, a report can then be generated. Basic RF Performance LTE BAND4 LTE BAND13 BW Mode Maximum Target BW Mode Maximum 5MHZ 10MH Z 15MH Z 20MH Z QPSK 22.5dBm1.5 16QAM 22.5dBm1.5 QPSK 22.5dBm1.5 16QAM_UP _27RB 22.5dBm1.5 QPSK 22.5dBm1.5 16QAM_UP _27RB 22.5dBm1.5 QPSK 22.5dBm1.5 16QAM_UP _27RB 22.5dBm1.5 5MHZ 10MHZ QPSK 16QAM QPSK 22.5dBm1.5 22.5dBm1.5 22.5dBm1.5 16QAM_UP_27RB 22.5dBm1.5 B4/B13 TX Performance Minimum Output Power
<-39dBm Transmit OFF power
<-48.5 dBm Frequency Error
|f| (0.1 PPM + 15 Hz) PUSCH 17.5@QPSK BPSK ;12.5%@16QAM Error Vector Magnitude
(EVM) PUCCH 17.5%
PRACH 17.5%@FFS Carrier leakage Adjacent Channel Leakage power Ratio Transmitter Spurious emissions FJ1100L User Manual
<-24.2dBc@3.2 dBm 3.2dB
<-19.2dBc@-26.8 dBm 3.2dB
<-9.2dBc@-36.8 dBm 3.2dB
<-32.2dBc@ACPR1_UTRA
<-35.2dBc@ACPR2_UTRA
<-29.2dBc@ACPR_EUTRA
<-36 dBm@BW=1 KHz
<-36 dBm@BW=1 0KHz
<-36 dBm@BW=1 00KHz
<-30dBm@B W=1MHz 9 kHz f < 150 kHz 150 kHz f < 30 MHz 30 MHz f < 1000 MHz 1 GHz f < 12.75 GHz Frequency Range B4:
B13:
TX (1710--1755) MHZ TX (698--716) MHZ RX (2110--2155) MHZ RX (746--756) MHZ Safety Items Drop Design Temperature Range Humidity:
Altitude:
Safety Requirement 1.2meter 6 direction standard drop test
-40 to 85C Operation
-50 to +100 C Storage 20% to 90% Operation 10% to 95% Storage
-500 to +18,000m UL Listing Others Operator Requirement ESD Requirement Industry Canada/ AT&T (optional) 15KV non-conductive 3. Software Features Basic Software Items Air Interface 1x Data IP Stack Upgrade Method RUIM Compatible with None-RUIM Remote Update Power Modes AT Command Report Driver GPIOs LEDs Watch Dog Reset Startup Banner FJ1100L User Manual Requirement CAT1 B4/B13; GPS Supported Ipv4/IPV6 Remote update / PC tool Optional Supported Supported Supported Supported Supported3000records GPIOLEDGPSUART Interrupt for Door Open Detect, Ignition Status GPS Status,CAT-1 Status Supported (CBP8.2 integrated) Soft reset Supported Power Modes The FJ1100L device supports several power modes that are set by the power mode command. In full power mode the cellular subsystem will maintain a persistent cellular connection whenever service is available as well as an IP connection where available. Any hardware or software reset will interrupt any power mode and return the device to full power mode. In summary, the conditions permanently restoring full power mode include:
Power cycle Reset command SMS or UART power mode command Motion detect (if detector installed and enabled) When in a power down mode, the following resources will cause interrupts that will wake the FJ1100L and cause it to attempt complete the function associated with the interrupt. Simultaneous interrupts will cause sequential completion of each associated function. These interrupts include:
Report timer GPIO change Battery threshold Heartbeat FJ1100L User Manual Power-up The related interrupt function will be attempted for a total duration set the associated parameter in the power mode command. Reset There is an internal soft reset. Test Method Hardware Test Item Baseband Function Test RF Test Description Power Input Test Power Consumption and Current Test Heat Dissipation Test UART Stability Test GPIO Level Test LED Stability Test Drop Down Test High/Low Temperature Test Humidity Test RF Performance Test GPS Performance Test Antenna Performance Test ESD Test Software Test Test Environment Construct message Test environment 1. usb dongle and PC as message server 2.send message to FJ1100L UDP Test environment 1.connect dongle to PC and create dialup as ip server UART Test environment 1.connect FJ1100L to pc with com serial cable 2.open Terminal tool and send at command 3.reponse can be shown at terminal window FJ1100L User Manual 4 Event codes The table below relates the Event codes in the message to the reason the message was generated:
Message
#
Description Auto Report (auto report when moving) Vibration alarm(report when GPS is OFF and vibration detected) Power cut alarm (report when external power is cut off) Power connected alarm (external power has been connected) Hardwired or Virtual Ignition ON detected Hardwired or Virtual Ignition OFF detected Input2 high alarm Input2 low alarm Device has stopped moving Heartbeat periodic report Input1 high alarm Input 1 Low alarm Crash Detected Message Type Interval Vibration Power Disconnect Power Connect Ignition ON Ignition OFF Input 2 High Input 2 Low Stop Heartbeat Input 1 High Input 1 Low Crash Alarm Heading Change Heading change detected Tow Alert Starter Disabled An output has been set by SMS command Starter Enabled Harsh Accel Harsh Brake Swerve Left Swerve Right An output has been cleared by SMS command Harsh acceleration has been detected Harsh Braking has been detected A left swerve has been detected A right swerve has been detected Device is moving but being pulled 0 1 2 3 4 5 6 7 8 9 13 14 19 24 25 35 36 41 42 43 44 Generation of these messages will occur based on the configuration settings on the device. The device is preconfigured by the software loaded on the device in the factory. The defaults in the software may vary depending on the configuration ordered with devices FJ1100L User Manual FCC Regulations This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment. The devise cannot be used within 20cm of any persons and must not be colocated within 20cm of other transmitter antennas Caution