FJ1000MV TM120M-A User Manual Positioning Universal 1 FJ1000MV Contents 1 Introduction ....................................................................................................................3 1.1ID and Tooling Design.......................................................................................................3 2 Hardware.........................................................................................................................3 2.1 Physical and Electrical Specifications ..............................................................................3 2.2 Input/Output...................................................................................................................3 2.3 Cellular Communication...................................................................................................3 2.4 Harnesses.........................................................................................................................3 2.5 Event Codes ....................................................................................................................4 2.6 System network structure...............................................................................................5 2.7 Appearance and installation instructions........................................................................5 3 USER MANUAL.................................................................................................................6 3.1 INTRODUCTION...............................................................................................................6 3.2 List...................................................................................................................................6 3.3 Description......................................................................................................................7 2 2.2 Input/Output 1.1 ID and Tooling Design 2.1 Physical and Electrical Specifications Dimensions:83.5mm*47.5mm*18mm Weight:60g(withoptionalbattery) InputVoltage:9-36VDC Powerconsumption:
-Activemode:100mA 12VDC
-Sleepmode:<8mA 12VDC Operatingtemperature:-30to80 Storagetemperature:-30to80 Downloadanddebugport:1 SWDInterface:1 FunctionLEDs:2 GPSStatusGreen CellularStatusOrange Buzzer:1 Operationmode LTE/GPS Operationband LTEB2/B4/B12;GPS1.57542GHz Modulation:QPSK/16QAM Thereare3harnessesthatmaybeusedwiththe TM120M-A:
1. 4wirepowerandI/Oharness 2. 4wireUart 3. 14wirepowerandI/Oharness Thepictureasbelow. 2.3 Cellular Communication 2.4 Harnesses FJ1000MV 3 FJ1000MV 2.5 Event Codes ThetablebelowrelatestheEventcodesinthemessagetothereasonthemessagewas generated:
Message #
Message Type Description Interval Vibration Power Disconnect Power Connect Ignition ON Ignition OFF Input 2 High Input 2 Low Auto Report (auto report when moving) Vibration alarm(report when GPS is OFF and vibration detected) Power cut alarm (report when external power is cut off) Power connected alarm (external power has been connected) Hardwired or Virtual Ignition ON detected Hardwired or Virtual Ignition OFF detected Input2 high alarm Input2 low alarm 0 1 2 3 4 5 6 7 8 9 10 11 12 4 FJ1000MV 2.6 System network structure GPS alarm is currently the most advanced security Settings. GPS alarm more expensive than ordinary burglar alarm, and need to pay the additional service fee, so the popularity is not high. And alarm is based on a GPRS network communication network, combining with the intelligent linkage of mobile phone and car anti-theft, this kind of alarm alarm is not restricted by distance, overlay network is wide, but need to pay the monthly rental. Buying guide to edit GPS alarm when the choose and buy, need to pay attention to is the comparison of several common GPS performance. 2.7 Appearance and installation instructions 3.1 Introduction. This chapter is user manual for TM120M. 3.2 List. 1.One UART cables. 5 FJ1000MV 6 2.three TM120M devices. 3.One DC 12V cable. FJ1000MV 3.3 Description. 1. Connect the UART cable to the UART interface of MCU on the device, the other side connect to PC, you can communication to MCU with UART cable. 2. Connect the DC 12V cable to the connector to DC 12V, you can use the DC 12v cable to supply power. of J203 on the device, the other side connect 7 FJ1000MV 3. The other interfaces of UART 2 on device is for modem debug and update firmware). the TM120M device are shown in the following pictures.(The Modem 8 FJ1000MV Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 9