Datalink DL01 - User Manual 19 May 2019 Updated 7 Jul 2019 Confidential 2 1. Description Datalink DL01 supports Wi-Fi technology IEEE 802.11b/g/n standards for single-band 2.4GHz two stream MIMO, including functionalities such as Space Time Block Code (STBC), Low-Density Parity Check
(LDPC), maximum likelihood (ML) MIMO receiver, maximum ratio combining (MRC) and Orthogonal frequency-division multiplexing (OFDM). Modulation schemes include BPSK, QPSK, 16-QAM, 64-QAM and forward error correction coding with rates of 1/2, 2/3, 3/4, 5/6. Transceiver includes two RF spatial stream paths, and four antenna connectors of which two are active simultaneously. External RF FEMs (front end-module) are used for transmitter PA (power amplifier) and receiver LNA (low noise amplifier). 2. Specification Technology Interfaces Channels for CE area Frequency for CE area Channels for FCC area Frequency for FCC area Channel bandwidth Guardian interval Maximum TX output power for CE area Maximum TX output power for FCC area Input voltage and current Operating temperature PCB (Printed circuit board) WiFi 802.11b/g/n standards for single-band 2.4GHz two stream MIMO Power supply and data: 42+11pin SMT Antenna: 4pcs U.FL RF antenna connectors (of which 2pcs active simultaneously) 1 13 2412 2472 MHz 1 11 2412 2462 MHz 20MHz,10MHz Long 800ns
+20dBm @EIRP
+28dBm @conductive Digital Voltage: 3.3V RF Voltage: 5.0V
-10C-----+55C HDI, 8 layer, 3-2b-3, FR4, thickness 0.815mm Confidential Declaration of Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC RF Radiation Exposure Statement Caution: This Module complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Labelling Instruction for Host Product Integrator Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following:
Contains FCC ID: 2AJTNDL01 any similar wording that expresses the same meaning may be used. 15.19 Labelling requirements shall be complied on end user device. Labelling rules for special device, please refer to 2.925, 15.19 (a)(5) and relevant KDB publications. For E-label, please refer to 2.935. Installation Notice to Host Product Manufacturer The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module. The module is limited to installation in mobile application, a separate approval is required for all other operating configurations, including portable configurations with respect to 2.1093 and difference antenna configurations. Antenna Change Notice to Host manufacturer If you desire to increase antenna gain and either change antenna type or use same antenna type certified, a Class II permissive change application is required to be filed by us, or you (host manufacturer) can take responsibility through the change in FCC ID (new application) procedure followed by a Class II permissive change application. FCC other Parts, Part 15B Compliance Requirements for Host product manufacturer This modular transmitter is only FCC authorized for the specific rule parts listed on our grant, host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. Host manufacturer in any case shall ensure host product which is installed and operating with the module is in compliant with Part 15B requirements. Please note that For a Class B or Class A digital device or peripheral, the instructions furnished the user manual of the end-user product shall include statement set out in 15.105 Information to the user or such similar statement and place it in a prominent location in the text of host product manual. Original texts as following:
For Class B Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. For Class A Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. ISED regulatory compliance statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may not cause interference.(2)This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :(1)Lappareil ne doit pas produire de brouillage; (2)Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Please notice that if the IC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains IC: 22057-DL01 any similar wording that expresses the same meaning may be used. Ltiquette dhomologation dun module dInnovation, Sciences et Dveloppement conomique Canada devra tre pose sur le produit hte un endroit bien en vue, en tout temps. En labsence dtiquette, le produit hte doit porter une tiquette sur laquelle figure le numro dhomologation du module dInnovation, Sciences et Dveloppement conomique Canada, prcd du mot contient , ou dune formulation similaire allant dans le mme sens et qui va comme suit :Contient IC :
22057-DL01 est le numro dhomologation du module This equipment complies with IC RSS102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Cet quipement est conforme aux limites d'exposition aux radiations IC CNR102 tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps. Manufacturer: ZHONGTIAN XUN Communication Technology Co., Ltd. Antenna information used during testing:
Antenna type: PCB Layout antenna,Diopole antenna Antenna gain: 3 dBi for each antenna Refer to antenna specification for details.