FCC ID: E675JS0062 GSM/EDGE Booster Amplifier, SPA9329-35N

by: Powerwave Technologies Inc latest update: 2003-08-15 model: 5JS0062

Two grants have been issued under this FCC ID from 11/18/2002 to 08/15/2003 (this is one of seven releases in 2003 for this grantee). Public details available include frequency information, manuals, and internal & external photos. some products also feature user submitted or linked password defaults, drivers, instructions, troubleshooting guides, & warrantee terms.

permalink for this FCC identifier

search for: Repair details

from iFixIt

Trade-in? Recycling locations

eg for Slack usage

all	frequencies			exhibits	applications
		manuals

all exhibits 17
1 ~ 2003-08-15 11
2 ~ 2002-11-18 9

app s				submitted / available
1 2	Manual	Users Manual	pdf	813.32 KiB
1 2	User Manual	Users Manual	pdf	986.01 KiB
1 2		Block Diagram	pdf
1 2		Cover Letter(s)	pdf
1 2		External Photos	pdf
1 2		ID Label/Location Info	pdf
1 2		Operational Description	pdf
1 2		Cover Letter(s)	pdf
1 2		Cover Letter(s)	pdf
1 2		Test Report	pdf
1 2		Test Setup Photos	pdf
1 2		Parts List/Tune Up Info	pdf
1 2		Cover Letter(s)	pdf
1 2		Internal Photos	pdf
1 2		ID Label/Location Info	pdf
1 2		Test Setup Photos	pdf
1 2		Parts List/Tune Up Info	pdf

exhibit
download
text

1 2

Manual

Users Manual

pdf

813.32 KiB

1930-1990 MHz Installation and Service Manual Model SPA9329-35 Booster Power Amplifier Copyright Powerwave Technologies, Inc., October 2002. All rights reserved October 2002 SPA9329-35 Installation & Service Manual 2002 Powerwave Technologies Incorporated. All rights reserved. Powerwave Technologies, and the Powerwave logo are registered trademarks Powerwave Technologies, Inc. reserves the right to make changes to the documentation and equipment, including but not limited to component substitution and circuitry changes. Changes that impact this manual may subsequently be incorporated in a later revision of this manual. October 2002 Powerwave Technologies, Inc. 1801 East St. Andrew Place Santa Ana, CA 92705 Tel: (714) 466-1000

(888) 797-9283 Fax: (714) 466-5800 Web Site: www.powerwave.com Copyright Powerwave Technologies, Inc., October 2002. All rights reserved ii October 2002 Par. No. 1-1 1-2 1-3 1-4 2-1 2-2 2-3 2-4 2-5 3-1 3-2 4-1 4-2 4-3 4-4 4-5 4-6 5-1 5-2 5-3 6-1 6-2 6-3 6-3.1 6-3.2 SPA9329-35 Installation & Service Manual Table Of Contents Section 1 General Description Page No. Introduction ..................................................................................................................................................... 1-1 General Description....................................................................................................................................... 1-1 Functional and Physical Specifications.................................................................................................... 1-1 Ordering Information ..................................................................................................................................... 1-1 Section 2 Installation Introduction ..................................................................................................................................................... 2-1 Electrical Service Recommendations........................................................................................................ 2-1 Unpacking and Inspection............................................................................................................................ 2-1 Installation Instructions................................................................................................................................ 2-2

+27 VDC Power & Ground Connector ......................................................................................................... 2-2 Section 3 Operating Instructions Introduction ..................................................................................................................................................... 3-1 Initial Start-Up and Operating Procedures ............................................................................................... 3-1 Section 4 Principles of Operation Introduction ..................................................................................................................................................... 4-1 RF Input Signal................................................................................................................................................ 4-1 RF Output Load ................................................................................................................................................ 4-1 Amplifier Functional Description................................................................................................................ 4-1 Amplifier Module Cooling ............................................................................................................................ 4-1 Power Distribution......................................................................................................................................... 4-2 Section 5 Maintenance Introduction ..................................................................................................................................................... 5-1 Periodic Maintenance................................................................................................................................... 5-1 Module Field Replacement .......................................................................................................................... 5-1 Section 6 Troubleshooting Introduction ..................................................................................................................................................... 6-1 Trouble shooting............................................................................................................................................. 6-1 Return for Service Procedures .................................................................................................................... 6-1 Obtaining an RMA .......................................................................................................................................... 6-1 Repackaging for Shipment ........................................................................................................................... 6-1 Copyright Powerwave Technologies, Inc., October 2002. All rights reserved iii October 2002 Figure No. 1-1 1-2 1-3 1-4 1-5 2-1 3-1 4-1 Table No. 1-1 1-2 2-1 3-1 5-1 6-1 SPA9329-35 Installation & Service Manual List Of Illustrations Page No. SPA9329-35 Front Isometric View ......................................................................................................... 1-3 SPA9329-35 Rear Isometric View .......................................................................................................... 1-3 SPA9329-35 Front View............................................................................................................................ 1-4 SPA9329-35 Rear View ............................................................................................................................ 1-4 SPA9329-35 Side View............................................................................................................................. 1-5

+27Vdc Power & Ground Connector........................................................................................................... 2-2 SPA9329-35 Front Panel Indicators ....................................................................................................... 3-2 SPA9329-35 Booster Amplifier Block Diagram................................................................................... 4-1 List Of Tables Page No. Major System Components........................................................................................................................... 1-1 SPA9329-35 Power Amplifier Functional Specifications ................................................................. 1-2

+27Vdc Power & Ground Connector Descriptions................................................................................... 2-2 SPA9329-35 Controls, Indicators, and Connectors............................................................................. 3-1 Periodic Maintenance................................................................................................................................... 5-1 Troubleshooting.............................................................................................................................................. 6-1 Copyright Powerwave Technologies, Inc., October 2002. All rights reserved iv October 2002 SPA9329-35 Installation & Service Manual Section 1 General Description 1-1 Introduction This manual contains information and procedures for installation, operation, and maintenance of Powerwaves model SPA9329-35 channel booster power amplifier. The manual is organized into six sections as follows:

tions. The amplifier is shown in figures 1-1 through 1-5. Each amplifier module has a power input, one RF input, and an RF output. Controls and indicators consist of a DC power switch with corre-

sponding LED power indicator and an amplifier over-temperature LED indicator (see section 3). Primary power input for the amplifier is +27 VDC. Cooling for the amplifier module is provided by one fan mounted on the rear of the amplifier module, shown in figure 1-1, which provides airflow over the two internal heat sinks. 1-3 Functional & Physical Specifications Functional and physical specifications for the amplifier are listed in table 1-2. 1-4 Ordering Information Table 1-1 lists the component numbers and descriptions to be used when ordering booster ampli-

fiers or components. Table 1-1 Major System Components Component Number SPA9329-35 Description 100-Watt Amplifier, +27 VDC Copyright Powerwave Technologies, Inc., October 2002. All rights reserved 1-1 October 2002 SPA9329-35 Installation & Service Manual Table 1-2 SPA9329-35 Booster Power Amplifier Functional Specifications

+27 VDC Power Model 1930-1990 MHz 200 kHz nominal

< 200 kHz/carrier 100 Watts (50 dBm) Parameters Frequency Range Carrier Spacing (center to center) Occupied Bandwidth Max Power Output per Carrier Maximum Module Gain 23 dB 1 dB Max Tx Input Level for 100 Watts Spurious Emissions Gain Flatness Across 20 MHz Band Operating Voltage Operating Current (per Input Connector X2) Operating Temperature:

Tx Input Connector Tx Output Connector Dimensions (+27 VDC Model) Mounting Options 0.5 Watts (27 dBm)

-65 dBc 0.5 dBm Maximum

+27 VDC 24 Amps @ +27 VDC

-0 C to +50 C SMA-F Type N Female 5.25H x 8.5W x 16.1D Weight 19, 23, or 24 relay rack mounted or outdoor enclosure mounted 12 lbs maximum Copyright Powerwave Technologies, Inc., October 2002. All rights reserved 1-2 October 2002 SPA9329-35 Installation & Service Manual Figure 1-1. SPA9329-35 Front Isometric View Figure 1-2. SPA9329-35 Rear Isometric View Copyright Powerwave Technologies, Inc., October 2002. All rights reserved 1-3 October 2002 SPA9329-35 Installation & Service Manual Figure 1-3. SPA9329-35 Front View Figure 1-4. SPA9329-35 Rear View Copyright Powerwave Technologies, Inc., October 2002. All rights reserved 1-4 October 2002 SPA9329-35 Installation & Service Manual Figure 1-5. SPA9329-35 Side View Copyright Powerwave Technologies, Inc., October 2002. All rights reserved 1-5 October 2002 SPA9329-35 Installation & Service Manual Section 2 Installation 2-1 Introduction This section contains unpacking, inspection, and installation instructions and recommendations for the Powerwave model SPA9329-35 booster power amplifier. Carefully read all material in this section prior to equipment unpacking or installation. Also read and review the operating pro-

cedures in section 3 prior to installing the equipment. It is important that the licensee perform these tasks correctly and in good faith. If applicable, carefully read the appropriate parts of the Federal Communications Commission (FCC) rules to determine how they apply to your installa-

tion. DON'T TAKE CHANCES WITH YOUR LICENSE. 2-2 Electrical Service Recommendations Powerwave Technologies recommends that proper AC line conditioning and surge suppression be provided on the primary AC input to the +27 Vdc power source. All electrical service should be installed in accordance with the National Electrical Code, any applicable state or local codes, and good engineering practice. Special consideration should be given to lightning protection of all systems in view of the vulnerability of most transmitter sites to lightning. Lightning arrestors are recommended in the service entrance. Straight, short ground runs are recommended. The elec-

trical service must be well grounded. Each amplifier system should have its own circuit breaker, so a failure in one does not shut off the whole installation. Circuit breakers should be thermal type, capable of handling the maximum anticipated inrush current, in a load center with a master switch. 2-3 Unpacking & Inspection This equipment has been operated, tested and calibrated at the factory. Carefully open the con-

tainer(s) and remove the amplifier module(s). Retain all packing material that can be reassem-

bled in the event that the unit must be returned to the factory. Exercise care in handling equipment during inspection to prevent damage caused by rough or careless handling. CAUTION Visually inspect the amplifier module for damage that may have occurred during shipment. Check for evidence of water damage, bent or warped chassis, loose screws or nuts, or extraneous pack-

ing material in the connector. If the equipment is damaged, a claim should be filed with the carrier once the extent of any damage is assessed. We cannot stress too strongly the importance of IMMEDIATE careful inspection of the equipment and the subsequent IMMEDIATE filing of the necessary claims against the carrier if necessary. If possible, inspect the equipment in the pres-

ence of the delivery person. If the equipment is damaged, the carrier is your first area of re-

course. If the equipment is damaged and must be returned to the factory, write or phone for a re-

turn authorization. Powerwave may not accept returns without a return authorization. Claims for loss or damage may not be withheld from any payment to Powerwave, nor may any payment due be withheld pending the outcome thereof. WE CANNOT GUARANTEE THE FREIGHT CAR-

RIER'S PERFORMANCE Copyright Powerwave Technologies, Inc., October 2002. All rights reserved 2-1 October 2002 SPA9329-35 Installation & Service Manual 2-4 Installation Instructions The SPA9329-35 booster amplifier module is designed for installation in an enclosure that permits access to the front of the module for connection of the RF cables and the power connec-

tors. Turn external primary DC power off before connecting any cables. WARNING 1. Connect the +27 VDC power source to the booster power input connector (see figures 2-1, 3-1, and table 2-1). Do not apply power at this time. 2. Connect the RF input cable to the RF IN connector. 3. Connect the RF output cable to the RF OUT connector. 4. Refer to section 3 for initial turn-on and checkout procedures. 2-5 +27 VDC Power & Ground Connector The +27 Vdc power and ground connections on the amplifier are made through a 3-pin female D-

Sub connector (figure 2-1) and are listed and described in table 2-1. 3 2 1 Figure 2-1 +27 Vdc Power & Ground Connector Table 2-1 +27 Vdc Power & Ground Connector Descriptions Pin 1 2 3 Signal Open

+27V RTN Description

+27 Vdc

+27 Vdc return Copyright Powerwave Technologies, Inc., October 2002. All rights reserved 2-2 October 2002 SPA9329-35 Installation & Service Manual Section 3 Operating Instructions 3-1 Introduction This section contains operating instructions for the SPA9329-35 power booster amplifier. 3-2 Initial Start-Up & Operating Procedures Operating controls, indicators, and connectors located on the SPA9329-35 booster amplifier module are listed in table 3-1 and corresponding locations for each are shown in figure 3-1. To perform the initial start-up, proceed as follows:

1. Verify that all power and RF input and output cables are properly connected, per section 2. CAUTION Before applying power, make sure that the input and output of the amplifier are prop-

erly terminated at 50 ohms. Do not operate the amplifier without a load attached. Re-

fer to table 1-2 for input power requirements. Excessive input power may damage the amplifier. The output coaxial cable between the amplifier and the antenna must be 50-ohm co-

axial cable. Use of any other cable will distort the output. NOTE 2. Turn on supply that provides +27 Vdc to the amplifier system. 3. Set the DC power ONOFF switch to ON. The corresponding PWR and TMP LED indicators should illuminate. Apply the RF input signal. 4. Table 3-1 SPA9329-35 Controls, Indicators, and Connectors Description Function RF channel input connector RF output connector

+27 VDC power input connector ONOFF switch. Applies DC power to channel amplifier LED indicator Illuminates when correspond-

ing ONOFF switch is set to ON LED indicator Illuminates when correspond-

ing ONOFF switch is set to ON. Goes out if amplifier overheats or VSWR is high. Copyright Powerwave Technologies, Inc., October 2002. All rights reserved 3-1 October 2002 RF IN RF OUT PWR IN ONOFF PWR TMP RF Input

+27 VDC Input SPA9329-35 Installation & Service Manual RF Output Channel DC Power ON OFF Switch DC Power Indicator Amplifier En-

able/Disable Indicator Figure 3-1 SPA9329-35 Controls, Indicators, and Connector Locations Copyright Powerwave Technologies, Inc., October 2002. All rights reserved 3-2 October 2002 SPA9329-35 Installation & Service Manual Section 4 Principles of Operation 4-1 Introduction This section contains a functional description of the SPA9329-35 power booster amplifier. 4-2 RF Input Signal The maximum input power should not exceed the limits specified in table 1-1. 4-3 RF Output Load The load impedance should be as good as possible (1.5:1 or better) in the working band for good power transfer to the load. 4-4 Amplifier Functional Description The SPA9329-35 power booster amplifier, shown in figure 4-1, operates in the 1930 MHz to 1990 MHz range. The operating band is determined by the operating frequency selection(s) of the base station (refer to table 1-2). The amplifier module consists of a single carrier amplifier pal-

let with the necessary combining and filtering to produce up to 100 watts (50 dBm) of output power with a maximum gain of 23 dB. The amplifier employs a class AB amplifier for maximum efficiency. The amplifier operates on +27 Vdc. The amplifier is compliant to the requirements of FCC Part 24 with respect to spurious emissions

(see table 1-2). All gain variations, for example those due to temperature, are reduced to the pas-

sive reference variations. SPA9329-35 Pre-Amp

+27 VDC RF In Comparator and Alarm Circuit TMP Reverse Detector Main Amplifier RF Out Figure 4-1 SPA9329-35 Booster Amplifier Block Diagram 4-5 Amplifier Module Cooling Each amplifier module is cooled using a rear-mounted fan circulating air flow across the amplifier heat sinks, the air then exits out the front of the module. This provides sufficient cooling to main-

tain the amplifier within the specified operating temperature range. Copyright Powerwave Technologies, Inc., October 2002. All rights reserved 4-1 October 2002 SPA9329-35 Installation & Service Manual 4-6 Power Distribution Primary DC power for the amplifier is provided by the host system. The amplifier generates all the required voltages internally from the main source. Copyright Powerwave Technologies, Inc., October 2002. All rights reserved 4-2 October 2002 SPA9329-35 Installation & Service Manual Section 5 Maintenance 5-1 Introduction This section contains periodic maintenance and performance test procedures for the SPA9329-

35 power booster amplifier. It also contains a list of test equipment required to perform the identified tasks. NOTE Check your sales order and equipment warranty before attempting to service or re-

pair the unit. Do not break the seals on equipment under warranty or the warranty will be null and void. Do not return equipment for warranty or repair service until proper shipping instructions are received from the factory. 5-2 Periodic Maintenance Periodic maintenance requirements are listed in table 5-1. Table 5-1 also lists the intervals at which the tasks should be performed. Task Inspection Cables & Connectors 12 Months Performance Tests 5-3 Module Field Replacement Table 5-1 Periodic Maintenance Interval Action Inspect signal and power cables for frayed insulation. Check RF connectors to be sure that they are tight. No periodic maintenance is necessary beyond that recommended by the base station manufacturer. The SPA9329-35 power booster amplifier module can be replaced in the field on site by a qualified technician with adequate ESD protection and experience maintaining RF power amplifi-

ers and similar equipment. To replace a power amplifier module, proceed as follows:

1. Set the amplifier module DC power ONOFF switch to OFF. 2. Disconnect the DC power cable from the amplifier module. 3. Disconnect the RF IN cable. 4. Disconnect the RF OUT cable. 5. Carefully remove the amplifier module. 6. Install replacement in reverse order. Copyright Powerwave Technologies, Inc., October 2002. All rights reserved 5-1 October 2002 SPA9329-35 Installation & Service Manual Section 6 Troubleshooting 6-1 Introduction This section contains a list of problems and a few suggested actions that may correct any prob-

lem with the SPA9329-35 power booster amplifier. If the suggested corrective action does not eliminate the problem, please contact your Powerwave field representative or the factory for fur-

ther instructions. NOTE Check your sales order and equipment warranty before attempting to service or re-

pair the unit. Do not break the seals on equipment under warranty or the warranty will be null and void. Do not return equipment for warranty or repair service until proper shipping instructions are received from the factory. 6-2 Troubleshooting Refer to table 6-1 for troubleshooting suggestions. Table 6-1 Troubleshooting Symptom Suggested Action Amplifier Module Inoperative Check for proper power supply voltage and that power input connector is properly seated in mating connector. Amplifier Module Not Enabled Check that the module ONOFF power switch is set to the TMP Indicator Not Illuminated ON position. Verify input RF is within specified power and frequency limits. Check that the cooling fan is operating. 6-3 Return For Service Procedures When returning products to Powerwave, the following procedures will ensure optimum response. 6-3.1 Obtaining An RMA A Return Material Authorization (RMA) number must be obtained prior to returning equipment to the factory for service. Please contact our Repair Department at (888) 797-9283 or (714) 466-

1000 to obtain this number, or FAX your request to (714) 466-5816. Failure to obtain this RMA number may result in delays in receiving repair service. 6-3.2 Repackaging For Shipment To ensure safe shipment of the amplifier, it is recommended that the package designed for the amplifier be used. The original packaging material is reusable. If it is not available, contact Powerwaves Customer Service Department for packing materials and information. Copyright Powerwave Technologies, Inc., October 2002. All rights reserved 6-1 October 2002

exhibit
download
text

1 2

User Manual

Users Manual

pdf

986.01 KiB

1930-1990 MHz Installation and Service Manual Model SPA9329-35N 2-Channel Booster Power Amplifier 044-05125 Rev. B Copyright Powerwave Technologies, Inc., July 2003. All rights reserved PRELIMINARY July 2003 SPA9329-35N Installation & Service Manual 2003 Powerwave Technologies Incorporated. All rights reserved. Powerwave Technologies, and the Powerwave logo are registered trademarks Powerwave Technologies, Inc. reserves the right to make changes to the documentation and equipment, including but not limited to component substitution and circuitry changes. Changes that impact this manual may subsequently be incorporated in a later revision of this manual. July 2003 Powerwave Technologies, Inc. 1801 East St. Andrew Place Santa Ana, CA 92705 Tel: (714) 466-1000

(888) 797-9283 Fax: (714) 466-5800 Web Site: www.powerwave.com 044-05125 Rev. B Copyright Powerwave Technologies, Inc., July 2003. All rights reserved ii PRELIMINARY July 2003 SPA9329-35N Installation & Service Manual Section 1 General Description 1-1 Introduction This manual contains information and procedures for installation, operation, and maintenance of Powerwaves model SPA9329-35N Two-Channel Power Booster Amplifier module. The manual is organized into six sections as follows:

Section 1. General Description Section 2. Installation Section 3. Operating Instructions Section 4. Principles of Operation Section 5. Maintenance Section 6. Troubleshooting 1-2 General Description The SPA9329-35N is a linear, two-channel booster amplifier that operates in a bandwidth of 60 MHz from 1930 MHz to 1990 MHz providing 35 watts (45.5 dBm) per channel at the combiner output port with a nominal gain of 21 dB total gain. The amplifier is modular in design, and ideally suited for use in GSM base stations. The amplifier, shown in figures 1-1 through 1-4, has a power input, two RF inputs, and one RF output. Controls and indicators consist of a DC power switch for each channel, corresponding LED power indicators, and alarm LED indicators (see section 3, table 3-1). Primary power for op-

erating the amplifier is -48 VDC. Each amplifier module has a fan assembly contained in the rear of the module, as shown in figures 1-2, to provide cooling. Air is drawn through the front of the amplifier, over the internal heat sinks, and then exhausted by the fan. 1-3 Ordering Information Table 1-1 lists major system component numbers and descriptions for use in ordering booster amplifiers or components. Table 1-1 Major System Components Component Number SPA9329-35N Description 35-Watt Amplifier, -48 VDC NOTE A quality transmit filter or duplexer must be installed after this amplifier to ensure FCC Type Acceptance of the amplifier. The filter/duplexer should be rated for at least 200 Watts average power and 800 Watts instantaneous power (minimum). 044-05125 Rev. B Copyright Powerwave Technologies, Inc., July 2003. All rights reserved PRELIMINARY July 2003 1-1 SPA9329-35N Installation & Service Manual Functional & Physical Specifications Functional and physical specifications for the SPA9329-35N amplifier are listed in table 1-2. Table 1-2 SPA9329-35N Booster Amplifier Functional Specifications Frequency Range Carrier Spacing (center to center) Occupied Bandwidth Max Power Output per Car-

rier Module Gain per Input Tx Input Level (per Input) for 35 Watts Gain Flatness Across 20 MHz Band IMD Performance Operating Voltage Operating Current (per In-

put Connector X2) Inrush Current (Peak) Operating Temperature:

Tx Input Connector Tx Output Connector Dimensions (+27 VDC Model) Mounting Options Weight 1930-1990 MHz 200 kHz nominal 200 kHz/carrier 35 Watts (45.5 dBm) 21 dB typical 10 mW (+10 dBm) to 10 Watts (+30 dBm) 0.5 dB Peak to Peak

-65 dBc maximum with two CW tones (one for each channel) unmodu-

lated @35 watts/tone

-38 VDC to 58 VDC 16 Amps @ -48 VDC (typical) 40 Amps Maximum 0 C to +50 C SMA-F x 2 (One per Input) Type N Female 5.25H x 8.50W x 15.30D including handle 19, 23, or 24 Relay Rack Mounted or Outdoor Enclosure Mounted 25 lbs 044-05125 Rev. B Copyright Powerwave Technologies, Inc., July 2003. All rights reserved PRELIMINARY July 2003 1-2 SPA9329-35N Installation & Service Manual Figure 1-1. SPA9329-35N Front Isometric View Figure 1-2. SPA9329-35N Rear Isometric View Copyright Powerwave Technologies, Inc., July 2003. All rights reserved PRELIMINARY July 2003 1-3 044-05125 Rev. B SPA9329-35N Installation & Service Manual Figure 1-3. SPA9328-35N Front Panel Figure 1-4. SPA9329-35N Side View Copyright Powerwave Technologies, Inc., July 2003. All rights reserved PRELIMINARY July 2003 1-4 044-05125 Rev. B SPA9329-35N Installation & Service Manual Section 2 Installation 2-1 Introduction This section contains unpacking, inspection, and installation instructions and recommendations for the Powerwave model SPA9329-35N Two-Channel Power Booster Amplifier module. Care-

fully read all material in this section prior to equipment unpacking or installation. Also read and review the operating procedures in section 3 prior to installing the equipment. It is important that the licensee perform these tasks correctly. If applicable, carefully read the appropriate parts of the Federal Communications Commission (FCC) rules to determine how they apply to your instal-

lation. DON'T TAKE CHANCES WITH YOUR LICENSE. 2-2 Electrical Service Recommendations Powerwave Technologies recommends that proper AC line conditioning and surge suppression be provided on the primary AC input. All electrical service should be installed in accordance with the National Electrical Code, any applicable state or local codes, and good engineering practice. Special consideration should be given to lightning protection of all systems in view of the vulner-

ability of most transmitter sites to lightning. Lightning arrestors are recommended in the service entrance. Straight, short ground runs are recommended. The electrical service must be well grounded. Each amplifier system should have its own circuit breaker, so a failure in one does not shut off the whole installation. Circuit breakers should be thermal type, capable of handling the maximum anticipated inrush current, in a load center with a master switch. 2-3 Unpacking & Inspection This equipment has been operated, tested, and calibrated at the factory. Carefully open the con-

tainer(s) and remove the amplifier module(s). Retain all packing material that can be reassem-

ence of the delivery person. If the equipment is damaged, the carrier is your first area of re-

course. If the equipment is damaged and must be returned to the factory, write or phone for a re-

turn authorization (see paragraph 6.3). Powerwave may not accept returns without a return au-

thorization. Claims for loss or damage may not be withheld from any payment to Powerwave, nor may any payment due be withheld pending the outcome thereof. WE CANNOT GUARANTEE THE FREIGHT CARRIER'S PERFORMANCE 044-05125 Rev. B Copyright Powerwave Technologies, Inc., July 2003. All rights reserved 2-1 PRELIMINARY July 2003 SPA9329-35N Installation & Service Manual 2-4 Installation Instructions The SPA9329-35N booster amplifier module is designed for installation in enclosures that permit access to the front of the module for connection of RF cables and the power connectors (refer to paragraphs 2-5, and 2-6 for connector descriptions). Turn external primary DC power off before connecting any cables. WARNING 1. Connect the power source to the booster amplifier power input connector (see figure 2-1, 3-

1, and table 2-1). Do not apply power at this time. 2. Connect the RF input cable(s) to the RF IN connector(s). 3. Connect an RF cable from the RF OUT (Type-N) to the transmit filter input. It is highly recommended that the output of the SPA9329-35N Booster Amplifier be fed through an appropriate bandpass transmit filter prior to the transmit antenna input. CAUTION 4. Connect the antenna cable to the RF filter output connector. 5. Refer to section 3 for initial turn-on and checkout procedures. 2-5 RF Connectors The amplifier has two SMA female RF IN connectors and one RF OUT connector (refer to figure 3-1 for locations). The input power to the RF IN connectors should not exceed the level specified in table 1-2. The RF OUT connector is Type-N female. 2-6 -48 VDC Power and Ground Connector The -48 Vdc power and ground connections on the amplifier are made through a 3-pin female D-

Sub connector (figure 2-1). Each pin and signal is listed and described in table 2-1. 1 2 3 Figure 2-1 -48 Vdc Power and Ground Connector Copyright Powerwave Technologies, Inc., July 2003. All rights reserved 2-2 PRELIMINARY July 2003 044-05125 Rev. B SPA9329-35N Installation & Service Manual Table 2-1 -48 Vdc Power and Ground Connector Pin Descriptions Pin 1 2 3 Signal Open

-48 Vdc Return Description Not Used

-48 Vdc DC Return 2-7 SPA9329-35N Alarm Connections Alarm connections are defined for the SPA9329-35N booster amplifier modules in table 2-2. Table 2-2 Alarm Connector Definitions Pin Number Contact Point With Respect To Common Amp 1 No Alarm Amp 1 Alarm Amp 1 DC Off Amp 2 No Alarm Amp 2 Alarm Amp 2 DC Off 1 NO Open Closed Closed Open Closed Closed 2 C C C C C C C 3 NC Closed Open Open Closed Open Open 6 NO Open Closed Closed Open Closed Closed 7 C C C C C C C 8 NC Closed Open Open Closed Open Open 044-05125 Rev. B Copyright Powerwave Technologies, Inc., July 2003. All rights reserved 2-3 PRELIMINARY July 2003 SPA9329-35N Installation & Service Manual Section 3 Operating Instructions 3-1 Introduction This section contains operating instructions for the SPA9329-35N Two-Channel Power Booster Amplifier module. 3-2 Initial Start-Up and Operating Procedures Operating controls, indicators, and connectors located on the SPA9329-35N booster amplifier module are listed in table 3-1 and corresponding locations for each are shown in figure 3-1. To perform the initial start-up, proceed as follows:

1. Verify that all power and RF input and output cables are properly connected as described in section 2. CAUTION Before applying power, make sure that the input and output of the amplifier are prop-

erly terminated at 50 ohms. Do not operate the amplifier without a load attached. Re-

fer to table 1-2 for input power requirements. Excessive input power may damage the amplifier. The output coaxial cable between the amplifier and the antenna must be 50-ohm. Use of any other cable will distort the output. NOTE 2. Set the power ONOFF switch to ON. The corresponding PWR and ALARM LED indicators should illuminate. Table 3-1 SPA9329-35N Controls, Indicators, and Connectors Function Description RF IN (2) RF OUT (1) PWR IN ONOFF PWR ALARM ALARMS Connector RF channel input connectors RF output connector

-48 VDC power input connector ONOFF switches. Apply DC power to amplifier channel LED indicators Illuminates when corresponding amplifier channel ONOFF switch is set to ON LED indicators Illuminates when corresponding amplifier channel disables because of an alarm. Alarms cable interface connector (see section 2 for defini-

tions). 044-05125 Rev. B Copyright Powerwave Technologies, Inc., July 2003. All rights reserved 3-1 PRELIMINARY July 2003 RF Inputs DC Power ON/OFF Switches Primary Power Input SPA9329-35N Installation & Service Manual RF Output Power and Alarm LEDs Alarms Connector Figure 3-1 SPA9329-35N Controls, Indicators, and Connector Locations 3-3 Power Setting Procedure WARNING Turn the amplifier off when disconnecting and moving amplifier RF cables. Never re-

move or install coaxial cables on either the input or output port when the power am-

plifier is turned on. Operating the power amplifier while disconnecting and connecting RF cables may damage the equipment and/or cause personal injury. A simplified power-setting example is shown in figure 3-2. 044-05125 Rev. B Copyright Powerwave Technologies, Inc., July 2003. All rights reserved 3-2 PRELIMINARY July 2003 SPA9329-35N Installation & Service Manual 10 m W to 10 W

+10 dBm to +30 dBm 35 W 45.5 dBm SCPA

(+21 dB) Filter Figure 3-2 Gain Example Block Diagram 1. Turn on external exciter/transceiver and apply RF input signal. Adjust the input power to achieve the desired output power (refer to table 1-2). 044-05125 Rev. B Copyright Powerwave Technologies, Inc., July 2003. All rights reserved 3-3 PRELIMINARY July 2003 SPA9329-35N Installation & Service Manual Section 4 Principles of Operation 4-1 Introduction This section contains functional descriptions for the SPA9329-35N Two-Channel Power Booster Amplifier module. 4-2 RF Input Signal The maximum input power should not exceed the limits specified in table 1-2. 4-3 RF Output Load The load impedance should be as good as possible (VSWR 1.5:1) in the operating band for good power transfer to the load. 4-4 Amplifier Functional Description The SPA9329-35N power booster amplifier, shown in figure 4-1, operates in the 1930 MHz to 1990 MHz range. The operating band is determined by the operating frequency selection(s) of the base station (refer to tables 1-2 and 1-3). The amplifier module consists of two single-carrier amplifier pallets with necessary combining and filtering to produce up to 35 watts (45.5 dBm) of output power with a typical gain of 21 dB. The amplifier employs class AB bias for maximum effi-

ciency. The amplifier operates from a -48 Vdc power source. The amplifier is compliant to requirements of FCC rules with respect to spurious emissions (see tables 1-2 and 1-3). Most of the amplifier gain vs temperature variations are due to LDMOS tran-

sistor characteristics.

-48 VDC Voltage Regulator

+15 VDC

+5 VDC RF Power Control and LED Drivers PWR ALARM RF In RF In Input Detector Temperature Sensor Pre-Amp Amplifier Bias Main Amplifier Output Detector Pre-Amp Main Amplifier Input Detector Temperature Sensor Amplifier Bias Output Detector 2:1 C o m b i n e r RF Out

-48 VDC Voltage Regulator

+15 VDC

+5 VDC RF Power Control and LED Drivers PWR ALARM Figure 4-1 SPA9329-35N Booster Amplifier Block Diagram 044-05125 Rev. B Copyright Powerwave Technologies, Inc., July 2003. All rights reserved 4-1 PRELIMINARY July 2003 SPA9329-35N Installation & Service Manual 4-5 Amplifier Module Cooling Each amplifier module is cooled using an enclosed rear-mounted fan circulating airflow across the amplifier heat sinks. Air is pulled from the front of the module and exits at the rear. This pro-

vides sufficient cooling to maintain the amplifier within its safe operating temperature range. 4-6 Power Distribution Primary DC power for the amplifier is provided by the host system. The amplifier generates all the required voltages internally from the main source. 044-05125 Rev. B Copyright Powerwave Technologies, Inc., July 2003. All rights reserved 4-2 PRELIMINARY July 2003 SPA9329-35N Installation & Service Manual Section 5 Maintenance 5-1 Introduction This section contains periodic maintenance and field replacement procedures for the SPA9329-

35N Two-Channel Power Booster Amplifier module. NOTE Check your sales order and equipment warranty before attempting to service or re-

pair the unit. Do not break seals on equipment under warranty or the warranty will be null and void. Do not return equipment for warranty or repair service until proper shipping instructions are received from the factory. 5-2 Periodic Maintenance Periodic maintenance tasks, performance intervals, and the appropriate actions to be taken are listed in table 5-1. Table 5-1 Periodic Maintenance Interval Action Inspect signal and power cables for frayed insulation. Check RF connectors to be sure that they are tight. No periodic maintenance is necessary beyond that recommended by the base station manufacturer. Task Inspection:

Cables & Connectors 12 Months Performance Tests 5-3 Module Field Replacement The SPA9329-35N power booster amplifier modules can be replaced in the field on site by a qualified technician with experience maintaining RF power amplifiers and similar equipment. To replace a power amplifier module, proceed as follows:

1. Set the amplifier module DC power ONOFF switches to OFF. 2. Disconnect the DC power cable from the amplifier module. 3. Disconnect the RF IN cables. 4. Disconnect the RF OUT cable. 5. Carefully remove the amplifier module. 6. Install replacement amplifier module in reverse order. 044-05125 Rev. B Copyright Powerwave Technologies, Inc., July 2003. All rights reserved 5-1 PRELIMINARY July 2003 SPA9329-35N Installation & Service Manual Section 6 Troubleshooting 6-1 Introduction This section contains a list of problems and suggested actions that may correct problems en-

countered with the SPA9329-35N Two-Channel Power Booster Amplifier module. If the sug-

gested corrective action does not eliminate the problem, please contact your Powerwave field representative or the factory for further instructions. NOTE Check your sales order and equipment warranty before attempting to service or re-

pair the unit. Do not break the seals on equipment under warranty or the warranty will be null and void. Do not return equipment for warranty or repair service until proper shipping instructions are received from the factory. 6-2 Troubleshooting Refer to table 6-1 for troubleshooting suggestions. Table 6-1 Troubleshooting Problem Suggested Corrective Action Amplifier Module Inoperative Check for proper power supply voltage and that power input connector is properly seated in mating connector. Amplifier Module Not Enabled Check that the channel ONOFF power switch is set to the ON position. 6-3 Return For Service Procedures When returning products to Powerwave, following the guidelines in the paragraphs that follow will ensure optimum response. 6-3.1 Obtaining An RMA A Return Material Authorization (RMA) number must be obtained prior to returning equipment to the factory for service. Please contact our Repair Department at (888) 797-9283 or (714) 466-

1000 to obtain this number, or FAX your request to (714) 466-5816. Failure to obtain this RMA number may result in delays in receiving repair service. 6-3.2 Repackaging For Shipment To ensure safe shipment of the amplifier, it is recommended that the package designed for the amplifier (original packaging material) be used for reshipment. If it is not available, contact Powerwaves Customer Service Department for the proper packing materials and information. 044-05125 Rev. B Copyright Powerwave Technologies, Inc., July 2003. All rights reserved 6-1 PRELIMINARY July 2003

		frequency	equipment class	purpose
1	2003-08-15	1930 ~ 1990	AMP - Amplifier	Class II permissive change or modification of presently authorized equipment
2	2002-11-18	1930 ~ 1990	AMP - Amplifier	Original Equipment

Application Forms

app s	Applicant Information
1 2	Effective	2003-08-15
1 2	Effective	2002-11-18
1 2	Applicant's complete, legal business name	Powerwave Technologies Inc
1 2	FCC Registration Number (FRN)	0006343024
1 2	Physical Address	1801 E St Andrew Pl.
1 2		Santa Ana, California 92705
1 2		United States

app s	TCB Information
1 2	TCB Application Email Address	m******@ccsemc.com
1 2	TCB Application Email Address	i******@ckccertification.com
1 2	TCB Scope	B1: Commercial mobile radio services equipment in the following 47 CFR Parts 20, 22 (cellular), 24,25 (below 3 GHz) & 27

app s	FCC ID
1 2	Grantee Code	E67
1 2	Equipment Product Code	5JS0062

app s	Person at the applicant's address to receive grant or for contact
1 2	Name	J** D**
1 2	Title	Principal Reliability Engineer
1 2	Telephone Number	714 4********
1 2	Fax Number	714 4********
1 2	E-mail	j******@pwav.com

app s	Technical Contact
1 2	Firm Name	CKC Laboratories
1 2	Name	M**** C**
1 2	Physical Address	5473-A Clouds Rest
1 2		Mariposa, California 95338
1 2		United States
1 2	Telephone Number	209-9******** Extension:
1 2	Fax Number	209-9********
1 2	E-mail	s******@ckc.com

app s	Non Technical Contact
1 2	Firm Name	CKC Laboratories
1 2	Name	M****** C****
1 2	Physical Address	5437-A Clouds Rest
1 2		Mariposa, California 95338
1 2		United States
1 2	Telephone Number	209-9******** Extension:
1 2	Fax Number	209-9********
1 2	E-mail	s******@ckc.com

app s	Confidentiality (long or short term)
1 2	Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?:	Yes
1 2	Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?:	No
	if no date is supplied, the release date will be set to 45 calendar days past the date of grant.

app s	Cognitive Radio & Software Defined Radio, Class, etc
1 2	Is this application for software defined/cognitive radio authorization?	No
1 2	Equipment Class	AMP - Amplifier
1 2	Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant)	GSM/EDGE Booster Amplifier, SPA9329-35N
1 2		GSM/EDGE Booster Amplifier, SPA9329-35
1 2	Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application?	No
1 2	Modular Equipment Type	Does not apply
1 2	Purpose / Application is for	Class II permissive change or modification of presently authorized equipment
1 2	Purpose / Application is for	Original Equipment
1 2	Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization?	No
1 2	Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization?	No
1 2	Grant Comments	Class II permissive change filing. Power listed is conducted. The antenna(s) used with this transmitter must be fix-mounted on outdoor permanent structures. RF exposure compliance is addressed at the time of licensing, as required by the responsible FCC Bureau(s), including antenna co-location requirements of Section 1.1307(b)(3).
1 2	Grant Comments	Power listed is conducted. The antenna(s) used with this transmitter must be fix-mounted on outdoor permanent structures. RF exposure compliance is addressed at the time of licensing, as required by the responsible FCC Bureau(s), including antenna co-location requirements of Section 1.1307(b)(3).
1 2	Is there an equipment authorization waiver associated with this application?	No
1 2	If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded?	No

app s	Test Firm Name and Contact Information
1 2	Firm Name	Compliance Certification Services Inc
1 2	Firm Name	CKC Laboratories, Inc.
1 2	Name	S****** C**
1 2	Name	S** B**
1 2	Telephone Number	408-4******** Extension:
1 2	Telephone Number	209-9******** Extension:
1 2	Fax Number	408-4********
1 2	Fax Number	866-7********
1 2	E-mail	s******@ccsemc.com
1 2	E-mail	r******@ckc.com

Equipment Specifications
	Line	Rule Parts	Grant Notes	Lower Frequency	Upper Frequency	Power Output	Tolerance	Emission Designator	Microprocessor Number
1	1	24		1930	1990	100	Amp	GXW
1	2	24		1930	1990	100	Amp	G7W
	Line	Rule Parts	Grant Notes	Lower Frequency	Upper Frequency	Power Output	Tolerance	Emission Designator	Microprocessor Number
2	1	24		1930	1990	100	Amp	GXW
2	2	24		1930	1990	100	Amp	G7W

some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details

recent releases: 2BFWB-F1 Brilliant Labs Limited 2APN5PANELPRO120 Shenzhen Sonoff Technologies Co., Ltd. IHDT56AR7 Motorola Mobility LLC 2AZMA-PP-PBM5K-WT One Source Suppliers Inc. ACJ9TGWW23D Panasonic Corporation of North America