FCC ID: 2AYPJ-100222 Pozyx Anchor V2.2

1 Accurate Positioning Enterprise Anchor V2.2 USER MANUAL v1.10, 2023-08-16 2 Contents 1 Foreword ............................................................................................................................ 3 2 Disclaimer .......................................................................................................................... 3 3 Note to Operator .............................................................................................................. 3 4 Safety ................................................................................................................................. 3 5 About this Manual ............................................................................................................ 4 5.1 5.2 5.3 Audience ................................................................................................................................................... 4 Copyright .................................................................................................................................................. 4 Revision History ...................................................................................................................................... 4 6 Overview ............................................................................................................................ 5 7 General Technical Specifications ..................................................................................... 6 8 Installing the Anchor ........................................................................................................ 6 8.1 Mounting Anchors ................................................................................................................................ 6 8.2 8.3 8.4 Connecting Cables ................................................................................................................................ 8 Powering the Anchor ............................................................................................................................ 9 Anchor Headers ................................................................................................................................... 10 8.4.1 Mounting the IP66/67 header .............................................................................................. 11 8.4.2 Mounting the IP20 header ..................................................................................................... 12 8.5 Best Practices for Anchor Placement ........................................................................................... 12 8.5.1 8.5.2 Specific guidelines for 2D positioning: .............................................................................. 13 Specific guidelines for 3D positioning: .............................................................................. 13 8.6 Anchor Activation ............................................................................................................................... 14 8.6.1 8.6.2 UWB functionality ...................................................................................................................... 14 Bluetooth functionality ............................................................................................................ 14 9 Troubleshooting .............................................................................................................. 14 10 Ordering information ..................................................................................................... 15 11 Disposal ............................................................................................................................ 16 12 Regulatory information .................................................................................................. 16 12.1 FCC Compliance Statement ............................................................................................................ 16 12.2 ISED Compliance Statement ........................................................................................................... 17 12.3 CE Compliance Statement ............................................................................................................... 18 12.4 UKCA Compliance Statement ........................................................................................................ 18 12.5 SRRC Compliance statement .......................................................................................................... 18 3 1 Foreword Please read this manual carefully before using the product. Do also read and follow instructions from operator or licensee applicable to the specific installation. For best possible performance, continuous satisfactory safe operation, read and understand these instructions thoroughly before operating your equipment. 2 Disclaimer The information, instruction, and parts listed are applicable and current on the date when issued. Pozyx reserves the right to make changes without prior notice. 3 Note to Operator It is the operators responsibility to see that any person involved with the use or operation of this equipment follows all safety and operational instructions. Under no circumstances should this equipment be used if the equipment is faulty or the operator does not completely understand the operation of the equipment. 4 Safety All Pozyx equipment should be used with the greatest care and in accordance with all local safety regulations. It is prohibited to modify, open up, replace or exchange parts, change factory settings or perform any other action on Pozyx equipment that deviates from the way it was delivered. Doing so may present a hazard and will void any warranties. Under no circumstances can Pozyx be held liable in any way shape or form for any defects, damages, injuries, direct or indirect, that are the result of handling, using, installing or any other use of the equipment and failure to observe all necessary safety guidelines. 4 5 About this Manual 5.1 Audience This manual is intended for users of the Enterprise Anchor V2.2 in conjunction with the Pozyx Enterprise System. Any other use outside of the system is deemed incompliant and will void any warranties of the anchor, tag, system, or any Pozyx hardware. 5.2 Copyright All rights reserved. No part of this document may be reproduced or transmitted in any way or shape be it, electronic, mechanical, photocopying, recording, or otherwise, without the express prior written permission of the publisher. For information on getting permission for reprints and excerpts, contact POZYX NV. The content and illustrations are subject to change without prior notice. 5.3 Revision History Release Date 2022-01-25 2022-02-25 2022-03-01 2022-03-04 2022-03-22 2022-03-23 2022-05-12 2022-06-30 2023-02-23 2023-06-20 2023-08-16 Revision 1.0 1.1 1.2 1.3 1.4c 1.5c 1.6 1.7 1.8 1.9 1.10 Remarks Initial release Update of regulatory information Update of the ISED regulatory information Update of the FCC regulatory information Removed the FCC, ISED and CE regulatory information Added UWB CH3 for Chinese market Added SRRC Regulatory information Merge English/Chinese version Update technical specifications Update CMIIT ID Update technical specifications Correction typos Update pictures of mounting brackets Added UWB CH3 for the CE, UKCA and FCC markets. Added additional FCC regulatory information. Update overview 5 6 Overview The Enterprise Anchor captures, preprocesses, and sends location data from tags to the Positioning system. It has been designed for optimal Ultra-Wideband performance and comes with robust casing options (IP20 or IP66/67), making it ideal for industrial environments. Mounting the Anchor is straightforward with the help of one of three mounting brackets. The anchor works within the Pozyx Enterprise system and requires an infrastructure of tags, anchors, switches, and a Positioning Server to accurately and correctly translate tag positions in a stream of real-time coordinates. Figure 1 Pozyx Enterprise System Architecture The Pozyx RTLS architecture comprises three main parts:

A network of anchors and tags. This network consists of two types of devices:

tags and anchors. The tag is a mobile device used to track the positions of an asset or person in real time. An anchor is a signal capturing device on a fixed, well-known position. A Positioning Server. This device connects to the anchors via Ethernet. It gathers all the data received from the anchors and transforms it into a position. By connecting to the Positioning Server, users can receive the real-time positioning data. The Pozyx web application. The web application is a visual interface to configure and manage the Pozyx RTLS system. It can be run locally from the Positioning Server itself or from the Pozyx cloud. Optionally a fourth part can be added:

The Pozyx Platform. The Pozyx platform is a software solution that leverages location data to provide real-time visibility and insights into tracked assets. It enhances the capabilities of the Pozyx RTLS system by offering advanced analytics, reporting, and integration options."

6 7 General Technical Specifications Parameter Information Supported UWB channels Channel 5, Channel 2 and 3 (for FCC and licensed customers in Bluetooth Sensors Power supply Certifications Operating conditions Storage conditions Dimensions Weight Ingress protection Europe) Bluetooth Low Energy V5.1 ready Acceleration, Air Pressure, Supply Voltage, Temperature POE/POE+, 3.5W typ, 4.5W max CE, FCC, ISED, SRRC, UKCA

-25 C to +55 C

-30 C to +70 C Standard version 158 x 98 x 53 mm 170 g IP20 Industrial version 229 x 98 x 59 mm 270 g IP66/67 8 Installing the Anchor 8.1 Mounting Anchors Mounting brackets allow users to install the Enterprise Anchor V2.2 to a ceiling, wall or corner. Three types of mounting brackets are available to mount an Enterprise Anchor V2.2:

Ceiling bracket (90-020-0004) Wall bracket (90-020-0005) 7 Corner bracket (90-020-0006) The Anchor is mounted with 4 M4 screws on the mounting bracket. NOTE: This equipment may only be operated indoors. Operation outdoors is in violation of 47 U.S.C. 301 and could subject the operator to serious legal penalties. 8 8.2 Connecting Cables Enterprise Anchors can be connected through Ethernet. Each Enterprise Anchor has 2 RJ45 100Base-T ports. They can be used to link up anchors in sequence which reduces the total amount of wiring required. This is called call this Daisy Chaining of Anchors. Figure 2 Enterprise Anchor PoE ports The port labeled 1should be connected to the Positioning Server. This can implemented either by a direct connection to one of the Anchor ports on the Positioning Server or by a connection through an Ethernet switch for large setups. The port labeled 2can be used to connect anchors in a daisy-chain. To create a chain of anchors connect the port 2 (OUT in the figure below) of an anchor to the port 1 (IN in the figure below) of the next anchor in the chain. Pozyx recommends using Ethernet cables that:

Are Pure Copper (Cu). Do not use Copper Clad Aluminum (CCA). Are Shielded Foil Twisted Pair (S/FTP) Are Cat5e (or better) Are AWG24 (or better). Both AWG24/1 and AWG24/7 are suited. Warning: It is advised not to use crossover Ethernet cables: all Ethernet cables should use the T568B wiring specified in the TIA/EIA-568 standard. Warning: For system stability it is advised to connect only anchors (and network switches solely used to aggregate anchors) to the ports labeled Anchor network on the Positioning Server. 9 8.3 Powering the Anchor There are two options to power an Enterprise Anchor:

Using Power-Over-Ethernet (PoE/PoE+). This option requires that an Ethernet switch with PoE capability is placed between the Positioning Server and the first anchor in a daisy-chain. Each anchor will provide power on the outgoing Ethernet cable for the next anchor in the chain. The Ethernet cable that provides power to an anchor must be connected to the port labeled 1. Remark: In general, 4-5 anchors (depending on the installation cabling and taking the environmental conditions into consideration) is the maximum for a chain when powered through a PoE+ Switch, more could cause networking issues. Be sure to use shielded Ethernet cables to eliminate cross talk. Local power DC jack: This option uses an external AC/DC convertor to power the first anchor in a daisy-chain. Warning: It is not allowed to power an Enterprise Anchor through the Ethernet Port 2. Warning: Make sure that you use the correct ports to connect the incoming and outgoing Ethernet cables to the Enterprise Anchor. 10 8.4 Anchor Headers Two types of headers are available for the Enterprise Anchor:

The header 90-010-0101 provides IP66 and IP67 ingress protection to the Enterprise Anchor. The Ethernet cables enter the header sideways. The header 90-011-0001 can optionally be used to guide the external cables. The ingress protection level of this solution is IP20. The header allows users to route the cabling upwards from or to the backside of the Enterprise Anchor. 11 8.4.1 Mounting the IP66/67 header 1. Place the RJ45 connector on the Ethernet cable according to the T568B convention when using an Ethernet cable without pre-confectioned connectors. Warning: Make sure that the RJ45 connectors are suited for the deployed Ethernet cable. 2. Place the tightening nut over the Ethernet cable. 3. Place the grommets over the Ethernet cable. 4. Pull the Ethernet cable thru the cable glands. 5. Plug the Ethernet connectors into the correct RJ45 jack. Route the Ethernet cables in a crossed way inside the header as illustrated below. Figure 3 Anchor Ethernet cable connection 6. Apply the provided lubricant on the O-rings of the IP66/67 header. Warning: Use only lubricants based on silicone or PTFE. 7. Push the IP66/67 header onto the Enterprise Anchor base module, until the clips snap on the base module. 12 8. Push the grommets in the cable glands. 9. Screw the tightening nut onto the cable glands until fixed. The maximum torque is 6.0 Nm. If the header needs to be unmounted, follow the above steps in reverse order. Warning: To provide IP66/67 protection, the diameter of the Ethernet cables must be tailored to the grommets provided with the header. The standard cable diameter should be 7 mm 10%. Contact Pozyx for other options. Warning: Make sure that the blind grommet, that is provided with the IP66/67 header, is placed in the right side cable gland if the anchor is the last in an anchor daisy-chain. 8.4.2 Mounting the IP20 header To mount the IP20 header follow the steps below:

1. Place the RJ45 connector on the Ethernet cable according to the T568B convention when using an Ethernet cable without pre-confectioned connectors. Warning: Make sure that the RJ45 connectors are suited for the deployed Ethernet cable. 2. Pull the Ethernet cables and the DC power cable (if used) through the appropriate holes in the header. Make sure that the cables will not cross after mounting the header on the Enterprise Anchor base module. 3. Plug the Ethernet connectors into the correct RJ45 jack. When used, also plug the DC plug into the DC Jack of the Enterprise Anchor 4. Push the header onto the Enterprise Anchor base module. 5. Push the cable into the top or rear exit holes in the header. 6. Re-adjust the header if it moved during Step 5. 8.5 Best Practices for Anchor Placement For the most accurate positioning the following generic guidelines apply:

The anchors should have line-of-sight to each other. An anchor should be placed each 10 m (1 anchor/100 m). However, this can vary depending on the environment. In some occasions it can be more or fewer, but we recommend a maximum anchor separation of 20 m. 13 A tag should be surrounded by anchors in all directions. This can be achieved by placing an anchor in each corner of the room in which tags are to be positioned. 8.5.1 Specific guidelines for 2D positioning:

Place the anchors high and in line-of-sight of the user. Placing the anchor high (on the ceiling or on the walls) increases the chance of receiving a good signal because there are fewer obstructions. Obstructions generally have a negative influence on the accuracy of the range measurements which has a direct effect on the positioning accuracy. Spread the anchors around the user. Don't place them on a straight line. For range-based systems, single range measurements will only give information in a single direction. This direction is exactly the direction from the user to the anchor. Because of this, it is best to spread the anchors such that they cover all directions. If the anchors are all on a straight line, the positioning error will be very large: A small change in radius (for example due to noise), will result in a very large change in the position of the intersection(s). In other words, the error on the range measurements is amplified! This is the same principle as in GPS, where it is called the geometric dilution of precision (GDOP). Make sure each anchor sees at least two, but preferably more neighboring anchors at a distance of not more than 15 to 20 meters, or even less in environments with many obstacles. Its very important that the clocks of the anchor are accurately synchronized with each other, and this happens through UWB. Its therefor important that not only the tags have line-of-sight to the anchors, but also that the anchors have a line-of-sight with each other. Place anchors vertically, with the connectors at the top. This keeps the antenna at the bottom Materials like metal, water and wires should stay away from the anchors, especially the antenna: Within a few centimeters from the antenna, there should be no metal at all, not even small screws. It is recommended to have a separation of 20 cm between the anchor and walls. Our mounting equipment can be used to achieve this. 8.5.2 Specific guidelines for 3D positioning:

Keep to the guidelines from above but place anchors at different heights:

The accuracy of the z coordinate will highly depend on the spread in heights of your anchors. Ideally, it is advised to place your anchors in the shape of a cube around your positioning zone as shown below. Try to maximize the distance between the lower and higher anchors. Twist the base surface of your cube 45 degrees as compared to the top surface:

14 Twisting the base surface will reduce the 3D convex hull of the anchors (e.g. the bottom corners of the cube are outside of the convex hull), but it will generally give you a higher chance of line-of-sight between a tag and the anchors. E.g. when your body is blocking 1 corner of the room it will just block line-of-sight with 1 anchor instead of 2. Furthermore its better for the tag to be surrounded by anchors from as much directions as possible. Place the bottom anchors upside down as this will point the antenna upwards

(= towards the tags). Always check https://docs.pozyx.io/enterprise/choosing-the-anchors-locations for the latest guidelines. 8.6 Anchor Activation 8.6.1 UWB functionality The general description of the Anchor setup and configuration and as part of a positioning system can be found at https://docs.pozyx.io/enterprise/installing-the-anchors. 8.6.2 Bluetooth functionality The use of the BLE functionality is not supported yet. 9 Troubleshooting 15 The Enterprise Anchor has a LED with 3 color options with the following state indications:

Parameter LED off Solid blue Solid red Blinking orange Solid orange Blinking Green Solid Green Blinking red Blinking blue Information Anchor powered off or general malfunction Startup or Maintenance mode No Ethernet link Link on Ethernet interface established IP address obtained Anchor operational, no UWB activity present Anchor operational, UWB activity present General malfunction Pozyx reserved mode 10 Ordering information Part Number Description 10-002-0022 90-010-0101 90-011-0001 90-020-0004 90-020-0005 90-020-0006 Enterprise Anchor V2.2 IP66/67 header for the Enterprise Anchor IP20 header for the Enterprise Anchor Ceiling bracket (screws & washers included) Wall bracket (screws & washers included) Corner bracket (screws & washers included) 16 11 Disposal When the product reaches end of life, dispose it properly in accordance with local laws and regulations. Disposal of the packaging material

(EU directive 94/62/EC on packaging and packaging waste) This marking indicates that the products packaging material can be recycled. Disposal of this product

(EU directive 2012/19/EU on Waste Electrical & Electronic Equipment) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. AC/DC convertors) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Household users should contact either the supplier where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal. Please contact the local municipal office for information on the nearest recycling station. 12 Regulatory information 12.1 FCC Compliance Statement This device complies with Part 15 of the FCC Rules:

Operation is subject to the following conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes and Modifications not expressly approved by Pozyx NV can void your authority to operate this equipment under Federal Communications Commission rules. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. This 17 equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. This device is in compliance with part 15.517 of the FCC Rules. This equipment may only be operated indoors. Operation outdoors violates 47 U.S.C. 301 and could subject the operator to serious legal penalties. Radiation Exposure Statement The device complies with the requirements set forth in CFR 47 Sections 2.1091 for an uncontrolled environment. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. 12.2 ISED Compliance Statement This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas license-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Radiation Exposure Statement The device has been found to be compliant to the requirements set forth in Industry Canada RSS-102 for an uncontrolled environment. The antenna(s) used for this transmitter must be 18 installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. 12.3 CE Compliance Statement The manufacturer, Pozyx NV, Vrijdagmarkt 10/201, 9000 Gent, Belgium declares that the product:

10-002-0022: Pozyx Anchor V2.2 with BLE is conform to the following Directives:

2014/53/EU (Radio Equipment Directive) 2011/65/EU (ROHS), amended by 2017/2102/EU and 2015/863/EU See the CE Declaration of Conformity for full details on the applied standards. 12.4 UKCA Compliance Statement The manufacturer, Pozyx NV, Vrijdagmarkt 10/201, 9000 Gent, Belgium declares that the product:

10-002-0022: Pozyx Anchor V2.2 with BLE complies with the requirements of the following regulations:

Radio Equipment Regulations 2017 (S.I. 2017/1206) The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 (S.I. 2012/3032) See the UKCA Declaration of Conformity for full details on the applied standards. 12.5 SRRC Compliance statement Manufacturer: Pozyx Product number: 100020022 CMIIT ID: 2022DJ8645 The use of ultra-wideband (UWB) equipment on aircraft is prohibited. The use of ultra-wideband (UWB) radio transmitting equipment is prohibited within 1 km around the radio astronomy station site listed in the footnote "CHN12" of the "Regulations on Radio Frequency Allocation of the People's Republic of China". 19 When the ultra-wideband (UWB) radio transmitting equipment is used, it shall not cause radio interference to the stations of other radio services, and shall not propose interference protection requirements to the stations of other radio services. Name and content of hazardous substances in the product:

Part number 100020022 Pb O Cd O Hg O Cr(VI) O PBBs O PBDEs O This form is prepared according to the provisions of SJ/T 11364 OIndicates that the content of this hazardous substance in all homogeneous materials of this part is below the limit requirement specified in GB/T 26572. XIndicates that the content of the hazardous substance in a homogeneous material of the part exceeds the limit requirement specified in GB/T 26572. 20 1 ................................................................................................................................... 21 2 ........................................................................................................................... 21 3 ........................................................................................................................ 21 4 ................................................................................................................................... 21 5 ........................................................................................................................ 22 5.1 .......................................................................................................................................................... 22 5.2 .......................................................................................................................................................... 22 5.3 ........................................................................................................................................ 22 6 ................................................................................................................................... 23 7 .................................................................................................................... 24 8 ........................................................................................................................... 24 8.1 ................................................................................................................................................. 24 8.2 ................................................................................................................................................. 26 8.3 ................................................................................................................................................. 27 8.4 ................................................................................................................................................. 28 8.4.1 IP66/67 ....................................................................................................................... 29 8.4.2 IP20 ............................................................................................................................. 30 8.5 .......................................................................................................................... 30 8.5.1 8.5.2 2D ............................................................................................................... 31 3D ............................................................................................................... 31 8.6 ................................................................................................................................................. 32 8.6.1 ................................................................................................................................... 32 8.6.2 ........................................................................................................................................ 32 9 ........................................................................................................................... 32 10 ........................................................................................................................... 32 11 ................................................................................................................................... 33 12 ........................................................................................................................... 33 12.1 ............................................................................................................ 33 21 1 2 Pozyx 3 4 Pozyx Pozyx Pozyx 22 5 5.1 Pozyx Pozyx 5.2 POZYX NV 5.3 2022-01-25 2022-02-25 2022-03-01 2022-03-04 2022-03-22 2022-03-23 2022-05-12 2022-06-30 1.0 1.1 1.2 1.3 1.4c 1.5c 1.6 1.7 ISED FCC FCCISED CE UWB CH3 SRRC

CMIIT ID 23 6 Pozyx IP20 IP66-67 Pozyx 4 Pozyx Pozyx Pozyx Web Pozyx Pozyx 7 Pozyx 24 5 2 FCC V5.1 POE/POE+ DC6 53 V 4.5 W CE, FCC, ISED, SRRC, UKCA

-25 C +55 C

-40 C +70 C 158 x 98 x 53 mm 170 g IP20 229 x 98 x 59 mm 270 g IP66/67 IP 8 8.1 Pozyx

(90-020-0004)

(90-020-0005) 25

(90-020-0006) 4 M4 8.2 Pozyx 2 RJ45 100Base-T 26 5 Pozyx PoE 1 2 2 OUT 1 IN Pozyx

(Cu) (CCA)

(S/FTP) Cat5e AWG24AWG24/1 AWG24/7 TIA/EIA-568 T568B 27 8.3

(PoE/PoE+) PoE 1 4-5 PoE+

DC /

2 28 8.4 90-010-0101 IP66 IP67 90-011-0001 IP20 8.4.1 IP66/67 1. T568B RJ45 29 RJ45 2. 3. 4. 5. RJ45 6 6. IP66/67 O PTFE 7. IP66/67 8. 30 9. 6.0 Nm IP66/67 7 mm 10% Pozyx IP66/67 8.4.2 IP20 IP20 1. T568B RJ45 RJ45 2. 3. RJ45 4. 5. 6. 5 8.5 10 m 1 /100 m 20 m 31 8.5.1 2D 15 20 20 8.5.2 3D Z 45 3D

. 1 1 2

https://docs.pozyx.io/enterprise/choosing-the-anchors-locations 32 8.6 8.6.1 https://docs.pozyx.io/enterprise/installing-the-anchors 8.6.2 BLE 9 3 LED LED IP Pozyx 10 Part Number Description 10-002-0022 90-010-0101 90-011-0001 90-020-0004 90-020-0005 90-020-0006 V2.2 IP66/67 IP20 11 33 94/62/EC 2012/19/EU

12 12.1 Pozyx 100020022 CMIIT ID: 2022DJ8645 UWB CHN12 1 UWB UWB 34 100020022

(Pb) O

(Cd) O

(Hg) O Cr(VI) O

(PBBs) O

(PBDEs O SJ/T 11364 O GB/T 26572 X GB/T 26572

Pozyx NV Date: 06/20/2023 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2AYPJ-100222 To whom it may concern:

We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Pozyx NV This authorization is valid until further written notice from the applicant. Sincerely, Print Name: Samuel Van de Velde Title: CTO Signature:

On behalf of Company: Pozyx NV Telephone: (32)92258607 E-mail: hw@pozyx.io

Pozyx NV TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding:

Confidentiality Request regarding application for FCC ID: 2AYPJ-100222 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Print Name: Samuel Van de Velde Title: CTO Signature:

On behalf of Company: Pozyx NV Telephone: (32)92258607 E-mail: hw@pozyx.io

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name Pozyx NV Address Grantee Code FCC ID Vrijdagmarkt 10/201 Gent 9000 Belgium 2AYPJ 2AYPJ-100222 Authorized Contact Name Samuel Van de Velde Contact Email Contact Phone hw@pozyx.io

(32)92258607 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

a) b) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, c) d) e) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO 17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) g) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Link to the Covered List: Covered List

[Pozyx NV] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules.

[Pozyx NV] (the applicant) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered list, established pursuant to 1.50002, as an entity producing covered equipment. Applicant Signature:

Date: 06/20/2023 Print Name:

Title:

Samuel Van de Velde CTO

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database QSF27-14-04 Rev 1.0 Rev. Feb 6, 2023 Page 1 of 1 Original Issue: Jan. 4, 2021

UWB15F PAG Checklist (Subpart 15F and KDB 393764 D01) @ TCBC Workshop (April 27, 2022) Model Name : 100020022 FCC ID : 2AYPJ-100222 UWB operation mode : Indoor Use UWB systems (Rule Part : 15.517) Radio test report number : SZCR221100396701 Common Requirements Check lists Bandwidth: 10 dB BW 500 MHz, or Fractional BW

.2 (15.503(a)) Frequency of highest emission occurs within the UWB bandwidth (15.521(e)) Technical Digital circuitry are subject limits as specified in (15.521(c)) General Part 15 (15.209) limits apply below 960 MHz Page 3 15.505 Cross Reference (15.521(a)) Remarks Refer to the page on 22 to 24 of the test report

-The 10dB bandwidth is 564 MHz. Refer to the page on 14 of the test report.

-The frequency of highest emission is 4581.524MHz. Refer to the page on 15 to 18 of the test report. Refer to the page on 15 to 18 of the test report. Refer to the page on 3 and of the test report. Grant Restriction Indoor Use UWB Systems

(15.517) Unwanted emissions must be measured over the frequency ranges as specified in 15.521(h) Refer to the page on 15 to 21 of the test report. UWB devices may not be employed for the operation of toys (15.521(a)). Operation onboard an aircraft, a ship or a satellite is prohibited (15.521(a)). Refer to the page on 5 of the user manual. The device is an anchor for positioning,it will not be employed for the operation of toys, aircraft, ship and satellite. Refer to the page on 5 of the user manual. The device is an anchor for positioning,it will not be employed for the operation of toys, aircraft, ship and satellite. Check lists Remarks Restricted to indoor operation by nature of design and manual notice (15.517(a)(1)) Refer to the page on 7 of test report and the page on 6 of the user manual. Shall not be intentionally directed to perform outside functions, such as entry detection (15.517(a)(2) Refer to the page on 5 of the user manual. Operation under the provisions of this section is limited to UWB transmitters employed solely for indoor operation. Refer to the page on 7 of the test report. Metal or underground storage tanks are considered indoors per (15.517(a)(4)) Refer to the page on 5 of the user manual. Page 11 Technical The use of fixed outdoor mounted antennas is prohibited (15.517(a)(3) Refer to the page on 11 of the test report.

-The antenna used in this product is a PCB antenna. Shall transmit only when sending information to an associated receiver (15.517(a) Refer to the page on 5 of the user manual. The UWB bandwidth shall be contained between 3100 MHz and 10,600 MHz (15.517(b)) Radiated emissions above 960 MHz shall conform to the mask specified in 15.517(c) Refer to the page on 24 of the test report.

-The highest frequency (fH) is 4824.3 MHz and the lowest frequency(fL) is 4260.3 HMz. Refer to the page on 19 to 21 of the test report. Peak EIRP limit of 0 dBm/50 MHz applies (15.517(e)) Refer to the page on 12 to 14 of the test report. Radiated emissions in the 1164-1240 MHz and 1559-1610 MHz bands limits as specified in 15.517(d) Refer to the page on 21 of the test report. Must bear a statement in a conspicuous location on the device or in the instruction manual:

This equipment may only be operated indoors. Operation outdoors is in violation of 47 U.S.C. 301 and could subject the operator to serious legal penalties. Refer to the page on 7 of the user manual.

Pozyx NV Request for Class II Permissive Change FCC ID: 2AYPJ-100222 Date : 06/20/2023 To: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Please be notified that we, the undersigned, (Pozyx NV) declare that the reasons for this Class II permissive change are as below:

Add UWB channel 3 via software. There's no change on hardware. The original FCC ID: 2AYPJ-100222. Date of Grant: 03/27/2022. Sincerely, Print Name: Samuel Van de Velde Title: CTO Signature:

On behalf of Company: Pozyx NV Telephone: (32)92258607 E-mail: hw@pozyx.io

UNITED STATES DESIGNATED AGENT LETTER Date: 06/20/2023 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Applicant Company Name: Pozyx NV Grantee Code:

Contact Name:

Address:

City/Province/Zip: Gent 9000 Belgium Telephone:

Fax:

Email:

(32)92258607

(32)92258607 hw@pozyx.io 2AYPJ Samuel Van de Velde Vrijdagmarkt 10/201 U.S. designated agent Company Name: FCC US Agent, LLC FRN: 0033402884 Contact Name: Tim Payne Address: 3722 Illinois Avenue City/Province/Zip: Saint Charles, IL, 60174, USA Telephone: 708-571-3148 Fax: 708-571-3148 Email: Support@FCCUSAgent.com Applicable Equipment: FCC ID: 2AYPJ-100222 ATTN: Director of Certification:

We, < Pozyx NV> and < FCC US Agent, LLC> understand and acknowledge the applicants consent and the designated agents obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and e-mail of the designated agent listed above. We, < Pozyx NV> and < FCC US Agent, LLC> acknowledge the applicants acceptance of its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Applicant U.S. designated agent Name (Printed): Samuel Van de Velde Name (Printed): Tim Payne Title: CTO Signature:

Title: Manager Signature: