FCC ID: 2AYPJ-100224 Pozyx Anchor V2.2

1 Accurate Positioning Anchor V2.2 USER MANUAL v1.3, 2022-03-04 2 Contents Contents .................................................................................................................................... 2 1 Foreword ............................................................................................................................ 3 2 Disclaimer .......................................................................................................................... 3 3 Note to Operator .............................................................................................................. 3 4 Safety ................................................................................................................................. 3 5 About this Manual ............................................................................................................ 4 5.1 5.2 5.3 8.2 8.3 8.4 Audience ................................................................................................................................................... 4 Copyright .................................................................................................................................................. 4 Revision History ...................................................................................................................................... 4 6 Overview ............................................................................................................................ 5 7 General Technical Specifications ..................................................................................... 6 8 Installing the Anchor ........................................................................................................ 6 8.1 Mounting Anchors ................................................................................................................................ 6 Connecting Cables ................................................................................................................................ 8 Powering the Anchor ............................................................................................................................ 9 Anchor Header ..................................................................................................................................... 10 8.4.1 Mounting the IP66/67 header .............................................................................................. 10 8.5 Best Practices for Anchor Placement ........................................................................................... 12 8.5.1 8.5.2 Specific guidelines for 2D positioning: .............................................................................. 12 Specific guidelines for 3D positioning: .............................................................................. 12 8.6 Anchor Activation ............................................................................................................................... 13 8.6.1 UWB functionality ...................................................................................................................... 13 9 Troubleshooting .............................................................................................................. 13 10 FAQ ................................................................................................................................... 14 11 Disposal ............................................................................................................................ 15 12 Regulatory Information ................................................................................................. 16 12.1 FCC Compliance Statement ............................................................................................................ 16 12.2 ISED Compliance Statement ........................................................................................................... 16 12.3 CE Compliance Statement ............................................................................................................... 17 3 1 Foreword Please read this manual carefully before using the product. Do also read and follow instructions from operator or licensee applicable to the specific installation. For best possible performance, continuous satisfactory safe operation, read and understand these instructions thoroughly before operating your equipment. 2 Disclaimer The information, instruction, and parts listed are applicable and current on the date when issued. Pozyx reserves the right to make changes without prior notice. 3 Note to Operator It is the operators responsibility to see that any person involved with the use or operation of this equipment follows all safety and operational instructions. Under no circumstances should this equipment be used if the equipment is faulty or the operator does not completely understand the operation of the equipment. 4 Safety All Pozyx equipment should be used with the greatest care and in accordance with all local safety regulations. It is prohibited to modify, open up, replace or exchange parts, change factory settings or perform any other action on Pozyx equipment that deviates from the way it was delivered. Doing so may present a hazard and will void any warranties. Under no circumstances can Pozyx be held liable in any way shape or form for any defects, damages, injuries, direct or indirect, that are the result of handling, using, installing or any other use of the equipment and failure to observe all necessary safety guidelines. 4 5 About this Manual 5.1 Audience This manual is intended for users of the Anchor in conjunction with the Pozyx Enterprise System. Any other use outside of the system is deemed incompliant and will void any warranties of the anchor, tag, system, or any Pozyx hardware. 5.2 Copyright All rights reserved. No part of this document may be reproduced or transmitted in any way or shape be it, electronic, mechanical, photocopying, recording, or otherwise, without the express prior written permission of the publisher. For information on getting permission for reprints and excerpts, contact POZYX NV. The content and illustrations are subject to change without prior notice. 5.3 Revision History Release Date 2022-01-25 2022-02-25 2022-03-01 2022-03-04 Revision 1.0 1.1 1.2 1.3 Remarks Initial release Update of regulatory information Update of the ISED regulatory information Update of the FCC regulatory information 5 6 Overview The Pozyx Anchor captures, preprocesses, and sends location data from tags to a Gateway. It has been designed for optimal Ultra-Wideband performance and comes with robust casing options (IP20 or IP66-67), making it ideal for industrial environments. Mounting the Anchor is straightforward with the help of three mounting brackets. The Anchor works within the Pozyx Enterprise system and requires an infrastructure of Tags, Anchors, switches, and a Gateway to accurately and correctly translate positions in a stream of real-time coordinates. Figure 1 Pozyx Enterprise System Architecture The Pozyx architecture comprises three main parts:

A network of anchors and tags. This network consists of two types of devices:

tags and anchors. The tag is a mobile device used to track the positions of an asset or person in real time. An anchor is a signal capturing device on a fixed, well-known position. A local gateway. This device is the positioning server and connects to the Anchors via Ethernet. It gathers all the data received from the Anchors and transforms it into a position. By connecting to the gateway, users can receive the real-time positioning data. The Pozyx web application. The web application is a visual interface to configure and manage the Pozyx system. It can be run locally from the gateway itself or from the Pozyx cloud. 6 7 General Technical Specifications For extensive technical specifications, please consult the Pozyx Anchor Datasheet. Parameter UWB channels Sensors Power supply Dimensions Weight Ingress protection Operating conditions Storage conditions Information Channel 5 Acceleration, Pressure, Supply Voltage, Temperature POE/POE+

157 x 98 x 53 mm 240 g IP66/67 (with add-on header)

-25 C to +55 C

-40 C to +70 C Installing the Anchor 8 8.1 Mounting Anchors Mountain brackets allow users to install the Pozyx Anchors security to a wall or ceiling. Three types of mounting brackets are available to mount an Anchor:

VESA pole mount (90-020-0001) 7 VESA wall mount (90-020-0002) VESA ceiling mount (90-020-0003) The Anchor is mounted with 4 M4 screws on the mounting bracket. 8 8.2 Connecting Cables Pozyx Anchors can be connected through Ethernet. Each Anchor has 2 RJ45 100Base-T ports. They can be used to link up anchors in sequence which reduces the total amount of wiring required. We call this Daisy Chaining of Anchors. Figure 2 Pozyx Anchor PoE ports The port labeled 1should be connected to the Positioning Gateway. This can implemented either by a direct connection to one of the Anchor ports on the gateway or by a connection through an Ethernet switch for large setups. The port labeled 2can be used to connect Anchors in a daisy-chain. To create a chain of Anchors connect the port 2 (OUT in the figure below) of an Anchor to the port 1 (IN in the figure below) of the next Anchor in the chain. Pozyx recommends using Ethernet cables that:

Are Pure Copper (Cu). Do not use Copper Clad Aluminum (CCA) Are Shielded Foil Twisted Pair (S/FTP) Are Cat5e (or better) Are AWG24 (or better). Both AWG 24/1 and AWF24/7 are suited. Warning: It is advised not to use crossover Ethernet cables: all Ethernet cables should use the T568B wiring specified in the TIA/EIA-568 standard. Warning: For system stability it is advised to connect only anchors (and network switches solely used to aggregate Anchors) to the ports labeled Anchor network on the gateway. 9 8.3 Powering the Anchor The Anchor is powered using Power-Over-Ethernet (PoE/PoE+). This option requires an Ethernet switch with PoE capability is placed between the gateway and the first Anchor in a daisy-chain. Each Anchor will provide power on the outgoing Ethernet cable for the next Anchors in the chain. The Ethernet cable that provides power to the Anchor must be connected to the port labeled 1. Remark: In general, 4-5 anchors (depending on the installation setup and environment and taking the conditions into consideration) is the maximum for a chain when powered through a PoE Switch, more will cause networking issues. Be sure to use shielded Ethernet cables to eliminate cross talk. Warning: It is not allowed to power an Anchor through the Ethernet Port 2. Warning: Make sure that you use the correct ports to connect the incoming and outgoing Ethernet cables on the anchor. 10 8.4 Anchor Header The header 90-010-0102 provides IP66 and IP67 ingress protection to the Anchor. The Ethernet cables enter the Header sideways. 8.4.1 Mounting the IP66/67 header 1. Place the RJ 45 connector on the Ethernet cable according to the T568B convention when using an Ethernet cable without pre-confectioned connectors. Warning: Make sure that the RJ45 connectors are suited for the deployed Ethernet cable. 2. Place the Tightening nut over the Ethernet cable. 3. Place the grommets over the Ethernet cable. 4. Pull the Ethernet cable thru the cable glands. 5. Plug the Ethernet connectors into the correct RJ45 jack. Route the Ethernet cables in a crossed way inside the cover as illustrated below. 11 Figure 3 Anchor Ethernet cable connection 6. Apply the provided lubricant on the O-rings of the IP66/67 header. Warning: Use only lubricants based on silicone or PTFE. 7. Push the IP66/67 header onto the Anchor base module, until the clips snap on the 8. Push the grommets in the cable glands. 9. Screw the tightening nut onto the cable glands until fixed. The maximum torque is base module. 6.0 Nm. If the header needs to be unmounted, follow the above steps in reverse order. Warning: To provide IP66/67 protection, the diameter of the Ethernet cables must be tailored to the grommets provided with the header. The standard cable diameter should be 5.4 mm 10%. Contact Pozyx for other options. Warning: Make sure that a blind grommet is placed in the right side cable gland if the Anchor is the last in an Anchor daisy-chain. 12 8.5 Best Practices for Anchor Placement For the most accurate positioning the following generic guidelines apply:

The Anchors should have line-of-sight to each other. An Anchor should be placed each 10 m (1 anchor/100 m). However, this can vary depending on the environment. In some occasions it can be more or fewer, but we recommend a maximum anchor separation of 20 m. A tag should be surrounded by anchors in all directions. This can be achieved by placing an Anchor in each corner of the room in which tags are to be positioned. 8.5.1 Specific guidelines for 2D positioning:

Place the anchors high and in line-of-sight of the user. Placing the anchor high (on the ceiling or on the walls) increases the chance of receiving a good signal because there are fewer obstructions. Obstructions generally have a negative influence on the accuracy of the range measurements which has a direct effect on the positioning accuracy. Spread the anchors around the user. Don't place them on a straight line. For range-based systems, a single range measurements will only give information in a single direction. This direction is exactly the direction from the user to the anchor. Because of this, it is best to spread the anchors such that they cover all directions. If the anchors are all on a straight line, the positioning error will (can?) be very large: A small change in radius (for example due to noise), will result in a very large change in the position of the intersection(s). Make sure each anchor sees at least two, but preferably more neighboring anchors at a distance of not more than 20 to 30 meters, or even less in environments with many obstacles Place anchors vertically, with the connectors at the top. This keeps the antenna at the bottom Materials like metal, water and wires should stay away from the anchors, especially the antenna: Within a few centimeters from the antenna, there should be no metal at all, not even small screws. It is recommended to have a separation of 20 cm between the anchor and walls. Extra mounting equipment can be used to achieve this. 8.5.2 Specific guidelines for 3D positioning:

Keep to the guidelines from above but place anchors at different heights:

The accuracy of the z coordinate will highly depend on the spread in heights of your anchors. Ideally, it is advised to place your anchors in the shape of a cube around your positioning zone as shown below. Try to maximize the distance between the lower and higher anchors. 13 Twist the base surface of your cube 45 degrees as compared to the top surface:

Keep the same max distance between the anchors as for 2D positioning (10 to 20 m depending on the environment) With only 6 anchors, it is possible that the resulting positions will be noisier. The recommendation in this case is to place 3 anchors in the top surface and 3 in the bottom surface Always check https://docs.pozyx.io/enterprise/Installing-the-anchors for the latest guidelines. 8.6 Anchor Activation 8.6.1 UWB functionality The general description of the Anchor setup and configuration and as part of a positioning system can be found at https://docs.pozyx.io/enterprise/Installing-the-anchors. 9 Troubleshooting The Anchor uses on a blue colored led. The state information is coded in the number of 1 second blinks in a 10 second period.:

Parameter LED off Solid blue Information Anchor powered off or general malfunction Startup or Maintenance mode 14 No blinks 1 blink 2 blinks Continuous blinks No Ethernet link Link on Ethernet interface established IP address obtained Error or Maintenance/Pozyx reserved state 10 FAQ 15 11 Disposal When the product reaches end of life, dispose it properly in accordance with local laws and regulations. Disposal of the packaging material

(EU directive 94/62/EC on packaging and packaging waste) This marking indicates that the products packaging material can be recycled. Disposal of this product

(EU directive 2012/19/EU on Waste Electrical & Electronic Equipment) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. AC/DC convertors) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Household users should contact either the supplier where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal. Please contact the local municipal office for information on the nearest recycling station. 16 12 Regulatory Information 12.1 FCC Compliance Statement This device complies with Part 15 of the FCC Rules:

Operation is subject to the following conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes and Modifications not expressly approved by Pozyx NV can void your authority to operate this equipment under Federal Communications Commission rules. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device is in compliance with part 15.517 of the FCC Rules. This equipment may only be operated indoors. Operation outdoors violates 47 U.S.C. 301 and could subject the operator to serious legal penalties. Radiation Exposure Statement The device complies with the requirements set forth in CFR 47 Sections 2.1091 for an uncontrolled environment. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. 12.2 ISED Compliance Statement This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas license-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference. 17 This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Radiation Exposure Statement The device has been found to be compliant to the requirements set forth in Industry Canada RSS-102 for an uncontrolled environment. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. 12.3 CE Compliance Statement The manufacturer, Pozyx NV, Vrijdagmarkt 10/201, 9000 Gent, Belgium declares that the product:

10-002-0024: Pozyx Anchor V2.2 without BLE is conform to the following Directives:

2014/53/EU (Radio Equipment Directive) 2011/65/EU (ROHS), amended by 2017/2102/EU and 2015/863/EU See the Declaration of Conformity for full details on the applied standards. END OF DOCUMENT

Pozyx Anchor V2.2 100020024 HVIN: 6

= 2020011234-6 MAC: 98:F9:C7:20:09:0A UWB-ID: 7878 FCC ID: 2AYPJ-100224 &) at IC: 27327-100224 CMIIT ID:2022DJ8367 IP66/67 QR Sx INPUT = POE 802.3 af/at Made in Estonia

Pozyx NV Date: 2024/01/17 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2AYPJ-100224 To whom it may concern:

We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Pozyx NV. This authorization is valid until further written notice from the applicant. Sincerely, Print Name: Samuel Van de Velde Title: CTO Signature:

On behalf of Company: Pozyx NV Telephone: (32)92258607 E-mail: hw@pozyx.io

Pozyx NV TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding:

Confidentiality Request regarding application for FCC ID: 2AYPJ-100224 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. If the device is marketed within aforementioned days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos Sincerely, Print Name: Samuel Van de Velde Title: CEO Signature:

On behalf of Company: Pozyx NV Telephone: (32)92258607 E-mail: hw@pozyx.io

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name Address Grantee Code FCC ID Authorized Contact Name Contact Email Contact Phone Pozyx NV Gaston Crommenlaan 4 bus 410B Ledeberg Belgium 9050 2AYPJ 2AYPJ-100224 Samuel Van de Velde hw@pozyx.io

(32)92258607 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

a) b) c) d) e) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO 17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS.

(1)

(2)

(3) f) g) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Link to the Covered List: Covered List

[Pozyx NV] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules.

[Pozyx NV] (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered list, established pursuant to 1.50002, as an entity producing covered equipment. Applicant Signature:

Date: 2024/01/17 Print Name:

Samuel Van de Velde CTO Title:

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database QSF27-14-04 Rev 1.0 Rev. Feb 6, 2023 Page 1 of 1 Original Issue: Jan. 4, 2021

Request for Class II Permissive Change Regarding: FCC ID: 2AYPJ-100224 Date: 2024/01/17 To: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Please be notified that we, the undersigned, (Pozyx NV) declare that the reasons for this Class II permissive change are as below:

1. Modification of Ethernet RJ45 shield termination from resistive to capacitive to solve issue with some POE switches. 2. Removal of the pressure sensor IC. The original grant issued date is 03/21/2022. Sincerely, Print Name: Samuel Van de Velde Title: CTO Signature:

On behalf of Company: Pozyx NV Telephone: (32)92258607 E-mail: hw@pozyx.io

UNITED STATES DESIGNATED AGENT LETTER Date: 2024/01/22 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Applicant Company Name:

Grantee Code:

Pozyx NV 2AYPJ U.S. designated agent Company Name:

Delaval Inc. Contact Name: Samuel Van de Velde Contact Name: Gavin Strang Address:

Telephone:

Gaston Crommenlaan 4 bus 410B Ledeberg Belgium 9050

(32)92258607 Address:

Telephone:

Suite 305 South 3000 Lakeside Drive Bannockburn, IL 60015, US

+1 (847) 224-6740 Email:

hw@pozyx.io Email:

usa.info@delaval.com Applicable Equipment: FCC ID: 2AYPJ-100224 ATTN: Director of Certification:

We, < Pozyx NV > and < Delaval Inc. > understand and acknowledge the applicants consent and the designated agents obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and e-mail of the designated agent listed above. We, < Pozyx NV > and < Delaval Inc.> acknowledge the applicants acceptance of its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Applicant U.S. designated agent Name (Printed): Samuel Van de Velde Name (Printed): Gavin Strang Title: CTO Signature:

Title: Director, MANA Market Development and Sale Signature:

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name Pozyx NV Vrijdagmarkt 10/201 Gent 9000 Belgium Address Grantee Code FCC ID Contact Email Contact Phone 2AYPJ 2AYPJ-100224 hw@pozyx.io

+32 9 225 86 07 Authorized Contact Name Samuel Van de Velde I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature:

Print Name:

Title:

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Samuel Van de Velde CEO Date:02-02-2022 a) b) c) d) e) f) g) Applicant Declaration Rev:0.0

Pozyx NV Date: 02-02-2022 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: 2AYPJ-100224 To whom it may concern:

We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou branch and Kobe Jian in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Pozyx NV. This authorization is valid until further written notice from the applicant. Print Name: Samuel Van de Velde Signature:

On behalf of Company: Pozyx NV Telephone: +32 9 225 86 07 E-mail: hw@pozyx.io Title: CEO