FCC ID: 2ACC86617010 Pricer Shelf Controller

1 Normal Usage Linking Pricer Label 1. Press and hold the Link button

. (The scanner beam is turned on.) 2. Scan the label barcode. The green link LED starts flashing and a beep/vibration confirms the scan. 3. Press and hold the link button again to scan the item barcode. The green link LED will be on for 1 s and a double beep/vibration confirms a successful link. 4. Scanning order can be reversed, i.e. scanning first item and then label is also possible. 5. If any other button is pressed after the first scan the link action is aborted and the scanned item/label is deleted. 6. Scanner beam automatically switches off after three seconds if the scanning fails. Release the link button and press again to activate the scanner. Other actions 1. Press and hold any of the action buttons.

(The scanner beam is turned on.) 2. Scan a barcode. Successful scan is confirmed by a beep/vibration. 3. To select a different action simply press and hold the corresponding button and scan like in step 2. Which action that is associated with which button is configured in the Pricer Server integration middleware. Note: The Shelf Controller supports EAN13, EAN7 and Code128 (17 characters) barcodes. Outbox After a successful link or scan the task is stored in the Shelf Controller Outbox and the outbox will flash blue until the command is LED successfully transferred to the server. The Shelf Controller can be used even if a wifi connection is missing. All tasks will then be stored in the Outbox and transferred once the Shelf Controller gets network access again. Single blue flash: No Wi-Fi coverage at the moment. Double blue flash: Has Wi-Fi connection but cannot connect to server, or the server does not respond with status code 2xx. When in sleep mode, the outbox LED will beep and give a short blue flash every five seconds indicating that there are unsent tasks. This will continue for 30 minutes, after that the beep and flash is repeated once every 30 minutes. The outbox can store 200 scans. A full outbox is indicated by three beeps and the outbox LED flashes red. Scanning is then disabled. To be able to scan again, empty the outbox either by connecting to the server so the commands can be transferred or go to AP mode and delete the outbox. Important! Make sure all actions in Outbox have been transmitted before ending work session. Otherwise actions may be transmitted after deadline. Low battery When the battery level is low, the battery LED will flash red to indicate that the Shelf Controller should be charged. The Shelf Controller can still be used for a while but is then disabled in order to protect the batteries. If the Shelf Controller has stored scans in the Outbox those scans will be kept and transmitted once the Shelf Controller is charged. Charging To charge the Shelf Controller, connect it to a PC or mobile charger using a USB-C cable. During charging the battery LED flashes green. Once the Shelf Controller is fully charged the battery LED turns steady green. Configure sound and vibration The Shelf Controller gives feedback on actions using LEDs, sound and vibration. Default sound and vibration settings are configured in the web interface. During normal operation it is possible to toggle sound (Off, low, high) by pressing buttons 12 and 9 for 1 s. During normal operation it is possible to toggle vibration (Off, On) by pressing buttons 12 and 10 for 1 s. 57767 Rev H, User manual Pricer Shelf Controller The Shelf Controller returns to the default sound and vibration settings after 8 hours of inactivity. 2 Configuring the Shelf Controller Enter AP mode An unconfigured Shelf Controller will automatically enter Access-Point (AP) mode when pressing one of the action buttons. A configured Shelf Controller can be reconfigured by putting it in AP mode by pushing Button 1 and Button 2 simultaneously for 5 seconds. One beep will sound and then the outbox LED starts flashing white. Configure in AP mode With the Shelf Controller in AP mode, use your laptop or phone to search for the Shelf Controller wifi network Pricer_Remote_xxxx and connect using a web browser to address 192.168.4.1. In the web browser, you will find different settings like Wi-Fi network name / Password, Backend server address and Sound/vibration settings. The Shelf Controller is default configured to acquire IP address via DHCP. For static address, check the Use Static IP checkbox and enter your data. The Shelf Controller supports WPA2 Personal and WPA Enterprise (PEAP-

MSCHAPv2) networks. For Enterprise, check the PEAP checkbox and enter a username. Note1 The Backend server (API Endpoint) address must start with http:// or https://. AP mode view AP mode view PEAP checked:

AP mode view Use Static IP checked Save configuration Once the user configuration is submitted the Shelf Controller control will attempt to connect to provided network and go to sleep. The config page will display the result of the connection test:

Even if the test fails the config is saved. This means that configuration can be done in advance at a location where the wifi is not present. If the Shelf Controller control is left unconfigured the user can manually put it to sleep to save battery by pushing any of the buttons except Button 1 and Button 2. In AP mode, the outbox can be cleared by pressing buttons 3 and 4 for 5 seconds. The command is acknowledged by two short beeps and the Outbox LED flashes green. No other configuration is affected. In AP mode, Factory reset can be obtained by pressing buttons 7 and 8 for 5 seconds. The command is acknowledged by three short beeps. Factory reset will clear all configuration and delete any left items in the outbox. 3 Firmware update The Shelf Controller supports Over the air

(OTA) updates. Enter AP by pushing Button 1 and Button 2 simultaneously for 5 seconds. One beep will sound and then the outbox LED starts flashing white. Press buttons 5 and 6 simultaneously for 5 seconds. One beep will sound, and the outbox LED will start flashing yellow. The Shelf Controller will connect to the customer server address configured in the Shelf Controller and look for new update in the /ota folder. Successful update is indicated by the outbox LED turns green for 5 seconds and two beeps. If update fails, the outbox LED will turn red instead for 5 seconds and three beeps will sound. After a failed update attempt, an error code is displayed on the Shelf Controllers config page which can give a hint of what went wrong. 4 Technical support Additional information about the Pricer Shelf Controller and its integration with the Pricer Server can be found at partner.pricer.com. 5 Battery and charging The internal rechargeable battery is not intended to be replaced during the service life time of the Shelf Controller. Any external power supply used for charging the Shelf Controller shall comply with relevant regulations and standards applicable in the country of intended use. The power supply should provide 5Vdc and a minimum rated current of 0.4A. 6 Disposal Waste of electrical and electronic equipment must not be disposed as unsorted municipal waste (RoHS and WEEE). Dispose the product separately in accordance with applicable federal, state and local regulations. 7 Compliance FCC compliance statement Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCCs RF radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Industry Canada certification/Certification Industrie Canada This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe A est conforme la norme NMB-003 du Canada. This equipment complies with Canada radiation exposure limits set forth for uncontrolled environments. This equipment should be installed and operated with a minimum distance of 20cm may be adjusted according to actual calculation result between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Dclaration dIC sur lexposition aux radiations:

Cet quipement est conforme aux limites dexposition aux radiations dfinies par le Canada pour des environnements non contrls. Cet quipement doit tre install et utilis une distance minimum de 20 cm entre lantenne et votre corps. Cet metteur ne doit pas tre install au mme endroit ni utilis avec une autre antenne ou un autre metteur. CE This equipment is not suitable for use in locations where children are likely to be present. 8 Certification The Shelf Controller complies with the European Radio Equipment Directive 2014/53/EU. FCC ID: 2ACC86617010 IC: 20234-6617010 This device contains FCC ID: 2AC7Z-

ESPWROOM32D. Article number: 66170-10 Size: 150 x 42 x 22 mm 9 Specifications Model: Pricer Shelf Controller Weight: 90 g Operating temp.: +5 C +40 C Charge connector: USB C Supply voltage: 5.0Vdc, 0.35A 10 Manufacturer information Pricer AB Vstra Jrnvgsgatan 7 SE-111 64 Stockholm, Sweden www.pricer.com 2020 Pricer AB, All rights reserved. Pricer Shelf Controller User manual

Label material:

PET Silver Label size:

45 x 13 mm Font:

Arial 5pt or similar Print colour:

Black. Actual size:

Shelf Controller Art. No. 66170-10 Rating 5V d.c. / 0.35A IC: 20234-6617010 FCC ID: 2ACC86617010 Made in China Note! It shall not be possible to rub out the text printed Shelf Controller Art. No. 66170-10 Rating 5V d.c. / 0.35A IC: 20234-6617010 FCC ID: 2ACC86617010 Made in China Enlarged:

Position:

Comments

Prepared Fredrik Tjerneld/200826 Reviewed

Approved

Scale 1:1 Units mm Format A4 Unit label Pricer Shelf Controller Document id. 1301-57759 Language EN/SV Page 1 of 1 Revision E

Label material:

PET Silver Label size:

45 x 13 mm Font:

Arial 5pt or similar Print colour:

Black. Actual size:

Shelf Controller Art. No. 66170-10 Rating 5V d.c. / 0.35A IC: 20234-6617010 FCC ID: 2ACC86617010 Made in China Note! It shall not be possible to rub out the text printed Shelf Controller Art. No. 66170-10 Rating 5V d.c. / 0.35A IC: 20234-6617010 FCC ID: 2ACC86617010 Made in China Enlarged:

Position:

Comments

Prepared Fredrik Tjerneld/200826 Reviewed

Approved

Scale 1:1 Units mm Format A4 Unit label Pricer Shelf Controller Document id. 1301-57759 Language EN/SV Page 1 of 1 Revision E

Title: PR | Cc E R BE) Created date: Page:

SGS_FCC_agent_auth_letter 27-Aug-20 1(1) Date: August 27, 2020 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: 2ACC8661 7010 To whom it may concern:

We, the undersigned, hereby authorize SGS Hong Kong Ltd. and YW Yung in SGS Hong Kong Ltd. to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, | acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Pricer AB. This authorization is valid until further written notice from the applicant. Name (Printed): Hakan Sjodin Title: Project Manager Signature: A. Bums On behalf of Company: Pricer AB Telephone: +46(0)7 081 080 65

so, cel SGS North America Inc. I I AME SGS North America Inc. Applicant Declaration f f

| ay Se SUITE 100 Ged Chet? Suwanee, Georgia 30024 ne. X ?

i: United States Pricer AB Vastra Jarnvagsgatan 7, SE-111 64 Stockholm, Sweden Grantee Code 0023608151

|, the undersigned, certify that | am an authorized signatory for the Applicant and therefore declare;

Applicant Legal Business Name Address a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

(1) labeling the equipment with the exact FCC ID as specified in this application,

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, c) _ if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with 1S017065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing.

(2) the Applicant shal/ make provisions to always have a production sample available upon request by SGS, FCC and/or ISED.

(3) the Applicant shal/, upon request by SGS, at the Applicant's expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Date:

Q7- AuG- LO20 Project Manager

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Applicant Declaration Rev:0.0

Title: PR | C le R | Created date: Page:

SGS_FCC_Confidentiality_request_2ACC8661 7010 25-Aug-20 To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Pricer AB Vastra Jarnvagsgatan 7; Stockholm 111 64 Sweden Regarding: Confidentiality Request regarding application for FCC ID 2ACC86617010 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Signature: Kh. IS Name (Printed): Hakan Sjodin Project Manager Pricer AB