Indoor 3. Make sure there is power to the outlet then HELPFUL TIPS SAFETY INFORMATION &
plug the fully assembled Power Stand into a a SPECIFICATIONS
. 3-wire grounded indoor outlet. Then plug + Make sure the receiver is plugged into a es Multi-Effects light strings into each outlet on the Power working AC outlet. This is a GROUNDED" device. The male plug Stand. The LED indicator light on the + Make sure the receiver and connected contains a ground pin and is only intended for Li ht Show wireless remote control (A) is lit when the equipment are on use with a three-pronged grounded outlet. ig Power Stand is powered on. * Make sure the remote control ON button is __ - pushed. use with a I20VAC power source. rower Stand Model: RCSTMI3 we PROGRAMMING INSTRUCTIONS Program the desired lighting effect from the wireless remote control or from the push-
button on the unit. By activating one of the following commands on the unit or from the wireless remote control, the lights will do one of the following:
* Flash = all light strings flash on/off rapidly
* Make sure the CR2052, SV battery in the remote control is still functioning. USE & CARE INSTRUCTIONS
+ Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat,
+ Do not secure the wiring of the product with staples or nails, or place on sharp hooks or PeLaaigsAgiet times Sa eginia Do not attach a device that exceeds the unit ratings:
8A / 1000W Tungsten (Maximum total load) 2.67A / 333W Tungsten (Each outlet) 3FT 16/3 AWG SJT Vinyl Power Cord WARNING: CHOKING HAZARD - Small Parts. Not for children under 3 years. FCC REGULATORY STATEMENT and simultaneously Dim = all light strings dim then brighten simultaneously Chase = light strings flash on/off in sequence by light string Fade = light strings dim then brighten in sequence by light string Random Mode = light strings run through all 4 basic effects randomly On = all lights are on Do not let lamps rest on the power supply cord or on any wire. Unplug the product when not in use. To avoid risk of fire, burns or electric shock, it should not be played with or placed where small children can reach it. Do not use this product for other than its intended use. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. For full benefit of the effects, plugging light strings into all three outlets is recommended. If there are any problems in getting the remote control to work properly, stop and read the Do not hang ornaments or other objects from cord, wire, or light strings. Do not close doors or windows on the product or extension cords as this may Notes: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential INSTALLATION z helpful tips section of these instructions. damage the wire insulation. installation. This equipment generates, uses and can INSTRUCTIONS If you continue to experience any problems, Dd hi di h cloth, radiate radio frequency energy and, if not installed please contact Technical Support toll free at io ROL cover the product with cloth: Paper or and used in accordance with the instructions, may any material not part of the product when in cause harmful interference to radio:
1. Connect the two pieces of the stand together using the 2 screws (E) to secure the bracket (C) to the 1-888-445-9955. use. communications. However, there is no guarantee that interference will not occur in a particular
* Before using or reusing, inspect product installation. If this equipment does cause harmful sera Ree kN oe ala Ce i ay
+4
" f Mase hs as sim 2. Mount the Power Center
(B) to the stand with the outlets facing front, aligning the hole in the bottom of the Power Center to the peg on the base. Push the Power Pe ee a BATTERY REPLACEMENT Use a Phillips Head screw driver to remove the screw on the battery compartment. Pull out the battery holder to replace one CR2032 3V Button Cell Battery. Insert CR2032 3V Button Cell Battery with the +" side up, and then re-insert the battery holder and reinstall the screw. Dispose of the old battery in compliance with all applicable laws. Contact your local solid waste authority for detailed information. AWA DNING: RA NAT RICORCE AE BATTEDIEC damaged, or frayed wire insulation or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire.
+ When storing the product, carefully remove the product from wherever it is placed to avoid any undue strain or stress on the product conductors, connections, and wires.
+ When not in use, store neatly in a cool, dry location protected from sunlight ee AEST ISTSNIGE 80: FORO OF Lerev lan) FeCR MON, WINCH can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Pa etre Sy coir Tel ee a Aone a eT ee EeSPe oemt eeeal utes Se aA gad) begat ep tame REL See ee ae ne nn inhale Sr spre alt att aaa al that it snaps into place. IN FIRE. BATTERIES MAY EXPLODE OR LEAK. product or provided with the product. technician for help.