MtP400 Series Operators Manual Printek, Inc. 1517 Townline Road Benton Harbor, MI 49022 269-925-3200 www.printek.com Printek Part Number 5885 Rev. B FCC Part 15 Class B This device complies with Part 15 of the RCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try too correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment complies with Canadian and FCC radiation exposure limits set forth for an uncontrolled environment. This equipment is in direct contact with the body of the user under normal operating conditions. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Part 15.21 Information to the user states that the users manual shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Bluetooth Equipped Models: This equipment contains either an OEM Serial Port Adapter from connectBlue with FCC ID: PVH070101 or a Printek Inc. Blue tooth module with FCC ID: 0013900444. Wi-Fi Equipped Models: This equipment contains an OEM Wireless LAN Node Module from DPAC Technologies with FCC ID: RTTABDB-SEDP. This device has shown compliance with the conducted emissions limits in 15.107, 15.207, or 18.307 adopted under FCC 02-157 (ET Docket 98-80). Battery Disposal Only dispose of used batteries according to your local regulations. If you do not know your local regulations, the Rechargeable Battery Recycling Corporation (RBRC) is a non-profit organization created to promote recycling of rechargeable batteries. For more information visit www.rbrc.org. Acknowledgments:
Printek is a registered trademark of Printek, Inc. Bluetooth is registered trademark of Bluetooth SIG, Inc. ONeil is a trademark of ONeil Product Development, Inc. Zebra and ZPL-II are registered trademarks of Zebra Technologies Palm OS is a trademark of PalmSource, Inc. PrintBoy is a registered trademark of Bachmann Software PrinterCE is a registered trademark of Fieldsoftware Products Wi-Fi is a registered trademark of the Wi-Fi Alliance Windows is a registered trademark of Microsoft Corporation All other trademarks are the property of their respective owners. 2004 By Printek, Inc., 1517 Townline Road, Benton Harbor, MI 49022. All rights reserved. Specifications are subject to change without notice. ii Read all setup and operating instructions before proceeding with operation. Do not operate in an enclosure unless properly ventilated. Make sure no ventilation openings are blocked or obstructed, which may result in the printer overheating. Do not operate near a heat source. Lesen Sie vor der Inbetriebnahme die Aufbau- und Bedienungsanleitung. Betreiben Sie den Drucker nicht in einem kleinen, geschlossenen Raum, es sei denn dieser wird ordnungsgem belftet. Achten Sie darauf, dass die Lftungen nicht blockiert oder versperrt sind, denn dies kann zum berhitzen des Druckers fhren. Nehmen Sie den Drucker nicht in der Nhe einer Wrmequelle in Betrieb. No user-serviceable parts inside. Refer service or repairs to a qualified service professional. Use of genuine Printek replacement parts is required to warrant proper, safe operation. Any alteration or modification of this device voids the user warranty and may make the product unsafe to operate. The print head and motors get hot during use. Wait until they cool before touching them. Make certain the printer is disconnected from AC power before removing any covers or performing any required cleaning or maintenance. Connecting this printer to an ungrounded receptacle can result in electrical shock. Never place the printer near inflammable or explosive substances. Do not operate near liquid or spill liquid into the printer at any time. Enthlt keine Teile, die vom Bediener instandgesetzt werden knnen. Bitte wenden Sie sich bei Instandsetzung oder Reparatur an qualifiziertes Kundendienstpersonal. Die Verwendung von echten Printek Ersatzteilen ist notwendig, um ordnungsgemen, sicheren Betrieb zu gewhrleisten. nderungen oder Modifikationen dieses Gerts machen die Garantie ungltig und knnen den sicheren Betrieb des Produkts gefhrden. Whrend des Druckens werden Druckerkopf und Motoren hei. Warten Sie, bis sich die Teile abgekhlt haben, bevor Sie sie berhren. Vergewissern Sie sich, dass der Drucker nicht mehr an die Stromquelle angeschlossen ist, bevor Sie Abdeckungen abnehmen oder das Gert reinigen bzw. warten. Schlieen Sie diesen Drucker nicht an eine ungeerdete Steckdose an; dies kann zum Elektroschock fhren. Setzen Sie den Drucker niemals in die Nhe von feuer- oder explosionsgefhrlichen Stoffen. Betreiben Sie den Drucker nicht in der Nhe von Flssigkeiten und lassen Sie keine Flssigkeiten in den Drucker gelangen.