PRINTEX Danmark ApS bluetooth* wireless headset for mobile phones
Lo
~S oe 6 Bluetooth _ Wirele Contents INtrOdUCHON a ccccsssmisicssamacnsecmnmenss 2 Headset Teall Osccissciscessssesacsscasece 3 Charging Wearing the headset.. Turning the headset on.. Turning the headset off.. Pairing the headset.. sin Making icCall isnwascimenaccnmecceeamosaseecens Redial the last number... Ending a call Answering a Call Rejecting a call....... Adjusting the volume... MUtING TNE: VOIUMG..cccnssesccrsrsancascsessans Transferring a call between the headset andthe mobile phone....................:00+ 9 Transferring a call between the headset and the mobile phone 1.During a call, press and hold the VOL+ button for 3 seconds to transfer the call to mobile phone. 2.Press the VOL+ button again; the call will be transferred to headset. The above function is available only after the headset is paired with the mobile phone. Introduction The Bluetooth techology is a standard for wireless short distance radio communications. Devices like headset,mobile phone or PDA can communicate with each other without wires within approximately 10 meters. The Tendystar E2 headset is a wireless headset based on the Bluetooth technology. It supports two profiles:Headset profile and Hands-free profile. It will work with any qualified Bluetooth device
(including headset or PDA) that supports the Headset profile or Hands-free profile.It also will allow you to take a call and adjust the volume without touching your mobile phone. Headset feature TALK /POWER button
} VOL+
Charging socket L ff Speaker___
~~ Microphone In the package Headset, Travel charger, Manual Rejecting a call Press and hold the TALK button for 3 seconds when the headset is ringing, Adjusting the volume Press the VOL+ button to increase the volume and press the VOL- to decrease the volume. uting the volume Press and hold VOL+ button and VOL- button for 3 second until you hear a beep. To end the mute function, press the VOL+ button and VOL- button until you hear a beep. Redial the last number Press and hold the VOL-button about 3 seconds. Ending a call To end a call, press the TALK button during a call. Answering a call Once you hear an incoming call ring in the headset, press the talkbutton. Charging At the first time, you must fully rechange it for about 8 hours until the blue indicator light turns on. For the subsequent charges, the charging will only take about 2hours. During the charge, both red and blue indicator lights turn to red, The indicator light will turn to blue when the charge is finished. While the battery is under-power, the indicator light will turn on; at last the indicator light will turn to blue.
*Be sure charging the battery with the supplied charger.
*Not allow the charging time more than 12 hours. Wearing the headset E2 is tied with a nice neck strap. During calling, wear the headset on the ear, without calling, it looks like a beautiful decoration hung on your neck. Using the headset Turning the headset on Press and hold the TALK button for 3 seconds, then the blue indicator light flashes rapidly. Turning the headset off Press and hold the TALK button for 3 seconds, then the indicator light turn to red and flashes rapidly. Pairing the headset Pairing is the connection between two Bluetooth devices to exchange data. The steps as follows:
1.Press and hold the TALK button about 6 seconds until the indicator light flashes red and blue alternatively. Now, the headset is pairing mode. 2.With your mobile device , search for the headset TDSTAR-E2. 3.Enter the headset passkey of 0000. 4.The Tendystar-E2 Bluetooth headset will now ready to use with your mobile device. Making a call Dial a phone number on the mobile phone. If your mobile phone offers the voice recognition feature, you could make a call directly from the headset. Press the TALK button and say one of your recorded voice tags, Make sure the voice tags have been recorded into the mobile phone. FCC Caution This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and usedin accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur ina particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment FCC Notes:
The manufacturer is not responsible for and radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment. CE Caution:
Hereby, PRINTEX Danmark ApS, declares that this Bluetooth Headset
(Intended use/Category: Wideband Data Transmission systems) is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Acopy of the DoC may be obtained through the following address. Vesterbrogade 63, DK-1620 Copenhagen V., Denmark