FCC ID: 2AMRATS813 POS. Terminal

 

: Bleep (UK) PLC

: POS. Terminal

: TS813

: Unit 1, Rowan House, 9-31 Victoria Road, London, NW10 6DP

Manufacturer

Address

Product Name

Model Number

WARNING

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be

required to take adequate measures.

WARNUNG

Dies ist ein Klass A Produkt. In einer örtlichen Umgebung kann dieses Gerät Funkstörungen verursachen.

ATTENTION

Ce produit est de classe A. Dans un environnement domestique, il peut causer des interférences radio. Auquel

cas, l’utilisateur sera amené à prendre les mesures adéquates.

Atenciõn

Este es un producto de la clase A. En ambientes domésticos éste producto puede causar radio interferencias en cuyo caso el usuario

deberá tomar las medidas oportunas.

Copyright Notice and Disclaimer

Bleep (UK) PLC makes no representations or warranties with respect to the contents

hereof and specifically disclaims any implied warranties of merchantability or fitness

for any particular purpose. Furthermore, Bleep (UK) PLC reserves the right to revise

this publication and to make changes from time to time in the contents hereof without

obligation of Bleep (UK) PLC to notify any person of such revisions or changes.

Possession, use, or copying of the software described in this publication is authorized

only pursuant to a valid written license from Bleep (UK) PLC.

FCC Notice

This equipment has been tested and has been found to comply with the limits for a Class A digital device, pursuant to Part 15 of the

FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated

in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the

users own expense.

Changes or modifications not expressly approved by manufacturer for compliance could void the user’s authority to operate the

equipment.



(C) Copyright Bleep (UK) PLC 2004. All rights Reserved.

No part of this publication may be reproduced, transmitted, transcribed, stored in a

retrieval system, or translated into any language or computer language, in any form or

any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise,

without the prior written consent of Bleep (UK) PLC.

All trademarks and registered trademarks are the property of their respective holders.

High Voltage & Static Electricity Precautions

Before removing the cover of this unit, please ensure that all electrical supply cords

are disconnected. High voltage is present inside the machine. Also please note that

static electricity is a constant danger to any computer system. The charge that can

build up in your body may be more than sufficient to damage integrated circuits on

any PC board. It is, therefore, important to observe basic precautions whenever you

use or handle computer components. Although areas with humid climates are much

less prone to static build-up, it is always the best to safeguard against accidents, which

may result in expensive repairs. The following measures should generally be

sufficient to protect your equipment from static discharge:

• Touch a grounded metal object to discharge the static electricity in your body (or

ideally, wear a grounded wrist strap).

• When removing or handling any boards or other system components, place all

materials on an antic static surface.

• Be careful not to touch the components on the boards, especially the “golden finger”

connectors on the bottom of some boards.

Important Notice (Lithium Battery)

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or

equivalent type recommended by the manufacturer. Dispose of used batteries

according to the manufacturer's instructions.

ATTENTION

Il y a un danger d'explosion si le remplacement de la pile n’est pas effectue

correctement; Remplacer uniquement avec une pile du meme type ou d'un type

recommande par le constructeur. Mettre au rebut les batteries usagees conformement

aux instructions du fabricant.

Environment specifications

Feature

Storage

Min

-20°C

Max

60°C

Operating

Min

5°C

Max

35°C

Comment

See note 1

See Note 2

See Note 2

No condensation

Ambient

Temperature

Humidity

Note 1: Care should be taken to ensure that the unit might not be subjected to

temperatures outside of this specification. Extreme hot or cold (particularly whilst

operational) may cause permanent damage to the system and could invalidate your

warranty.

Ambient temperature <= 35°C : 80% RH

Note 2: Where;

Ambient temperature > 35°C : < 80% RH

Hardware Requirements

Priority

Comments

Must have Android POS

Must have 170*92

Operating System

Must have Android6.0

Processor / Chipset

Must have Amlogic S912-2GHZ ARM Cortex-A53 octa core

Feature

Form Factor

PCBA Size

Display

Touch panel

DRAM

Storage

Ethernet

Speaker

Buzzer

Interface(External,Inter

nal)

Wireless connectivity

Must have 2.4G Wi-Fi: 802.11b/g/n

Must have Support 13.3” LCD panel (eDP)1366*768

Must have 13.3” USB interface PCAP touch screen

Must have 2GB DDR3

Must have 8GB flash

Must have 10/100M Ethernet

Must have 8Ω/2W Audio output (stereo)

Internal buzzer

Must have

External Connector

Must have 12V DC input socket DC-005 Ø2.5mm External

Must have 2×RS232 External (RX,TX) RJ45 Interface

Must have 2× 10/100M Ethernet (RJ45) External

Must have 1×T-flash card External max 32GB

Must have 2×USB External

Internal Connector

Must have 1× key upgrade External

Must have 1×MINI USB Device External

Must have 5×USB Internal

Must have 2×RS232 Internal (RX,TX) connector for printer board

Must have 2×12v output connector

Must have 2×5V output connector

Must have 4×GPIO connector

Must have 1×RTC connector 2PIN 2.0mm

Must have 1×ON/OFF Key output connector 2PIN 2.0mm

Must have 1×I2C output for capacitance touch screen(OPTIONAL)

Must have 1×Ethernet connector 6PIN 2.0mm Internal

HDMI board Interface Must have 1×eDP output for 13.3” inch panel(1366*768)

Must have 1×Audio output for speaker (8Ω/2W) Stereo

Software Requirements

Feature

Software Environment

Embedded OS

Boot Time

Start-Up

Audio Subsystem

Audio Channel(s)

Browser

Browser

Firmware Upgrade

1.3 Harness connection

Priority

Comments

Must have Android6.0

Must have <= 30s

Must have Stereo

Must have HTML,Image

Firmware update by memory card

Must Have

Important Notes

Power

As power surges, spikes and dropouts can interfere with system operation, it is

important to ensure that the power circuit dedicated to the ECR network be clean and

preferably on a separate spur from the main circuit box.

It is equally important to ensure that all peripherals (printers, computers, modems etc)

are also on the same dedicated power circuit as the ECR units.

Where clean power is not available, ensure that you install stand-alone power filters

or similar.

Mounting

Since heat will build up inside the terminal during normal operation, ventilation holes

are provided around the unit. Care should be taken to ensure that the unit is mounted

on a solid, level floor and that any cables protruding from the machine are neatly tied

and kept from blocking the base of the machine. Ideally a minimum 30mm gap should

be present around the complete circumference of the unit.

Spillage

Should any liquid be accidentally spilled onto the unit, rubber seals located around the

machine will protect the internal systems to a degree. However, care should be taken

to ensure that the unit is removed and dried quickly so as to avoid a build-up of fluid

inside the machine. Liquid should never be poured directly onto the surface of the

machine.

For cleaning, use a soft cloth with a non-abrasive cleaner such as isopropyl alcohol or

water.

Touch Panel

Do not place, lean or use any object other than a finger on the touch panel. The use of

pens, pencils or any other type of pointing device is not recommended and could

damage the unit.

The unit is fitted as standard with an anti-glare touch panel, however, it is not

recommended that the machine be installed directly underneath an overhead light,

particularly fluorescent strip lights. Changing the tilt angle of the terminal can

compensate for glare but a little thought during installation can help avoid distracting

reflections and assist the operator.



TS-813

Touch

Screen

Terminal

(Android)

Designed to cope with every aspect of the F&B

industry

System Features

Processor

• 13.3” eDP TFT Colour LCD Panel

• CPU：Amlogic ARM S912 Cortex-A53

(1366x768)

• 13.3” PCAP Touch Panel

• Wi-Fi 802.11b/g/n

• Android 6.0

• SD card socket

• 8GB built-in flash storage

Octa-core, 2GHz.

• 2Gb DDR3 RAM

I/O ports

• 3 x LAN （2 x external, 1 x internal）

• 7 x USB 2.0 HOST

(4 x external, 3 x internal）

1 x USB OTG

1 x MINI USB

• 3 x RS232 (2 x external，1 x internal）

• DC input （input 12V）

• 1 x cash drawer port

Optional built-in modules

• 20 x2 LCM Customer Display

• 7” Android customer display

• 58mm or 80mm thermal printer module

• Barcode / QR code scanner module

• RFID reader

• 2 or 3 track MSR

• Dallas magnetic sign-on reader

Bleep (UK) PLC

Rowan House, 9-31 Victoria Road, London NW10 6DP United Kingdom

email: sales@bleepplc.com Tel:+44 208 961 5200 http://www.bleepplc.com

FCC Caution: To assure continued compliance, any changes or modifications not expressly

approved by the party responsible for compliance could void the user's authority to operate this

equipment. (Example - use only shielded interface cables when connecting to computer or peripheral

devices).

FCC Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 20

centimeters between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

The antennas used for this transmitter must be installed to provide a separation distance of at least 20

cm from all persons and must not be co-located or operating in conjunction with any other antenna or

transmitter.



 

 

 

 

 

 

 

 

 

 

oe WARNING! High voltage parts inside. Unqualified engineers should NOT disassemble the system.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two Model No: TS-813 not eause harmful interference, INPUT: AC 100-240~, 2A , 50-60Hz any interfetenea rocelvedie

. including interference that may FCC ID: 2AMRATS813 cause undesired operation. S/N:

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required MADE IN TAIWAN

\ to take adequate measures. www.bleep.net S/N:

globalpayments Model No: TS-813 INPUT: AC 100-240~, 2A , 50-60Hz FCC ID: 2AMRATS813 Warning: This is a class A product. In a domestic environment this product may cause radio. interference in which case the user may be required to take adequate measures. WARNING! High voltage parts inside. Unqualified engineers should NOT disassemble the system. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. MADE IN TAIWAN www.bleep.net 7

 

 

PROTECH SYSTEMS Co.,Ltd No.24, Lane 365, yang Guang Street, Nei Hu District, Taipei, Taiwan R.O.C. Date: 2021/4/29 We, the undersigned, hereby authorize Worldwide Testing Services (Taiwan) Co., Ltd to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2AMRATS813 including the signing of all documents related to these matters. Any and all acts carried out by Worldwide Testing Services (Taiwan) Co., Ltd on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern:

Sincerely, Signature Name: Calvin Lin Title: Engineer Company: PROTECH SYSTEMS Co.,Ltd

 

 

PROTECH SYSTEMS Co.,Ltd

No.24, Lane 365, yang Guang Street, Nei Hu District,

Taipei, Taiwan

Federal Communications Commission

Equipment Authorization Branch

7435 Oakland Mills Road

Columbia, MD 21046

Date: 2021-05-04

Request for Long-Term Confidentiality

Company name: PROTECH SYSTEMS Co.,Ltd

FCC ID: 2AMRATS813

FCC Part 15 Certification

To whom it may concern:

In accordance with §§ 0.457(d) and 0.459 of CFR 47, PROTECH SYSTEMS Co.,Ltd

hereby requests Long-Term confidentiality of all Block Diagrams, Schematics,

Operational Description attachments for the subject application.

These documents contain detailed system and equipment description and related

information about the product which PROTECH SYSTEMS Co.,Ltd considers to be

proprietary, confidential and a custom design and otherwise would not release to the

general public. Since the design is a basis from which future technological products will

evolve, PROTECH SYSTEMS Co.,Ltd considers that this information would be of benefit

to its competitors and that the disclosure of the information in these documents would

give competitors an unfair advantage in the market.

Sincerely,

Signature

Name: Calvin Lin

Title: Engineer

Company: PROTECH SYSTEMS Co.,Ltd