FCC ID: HZB-S24-04

 

M INSTALLATION AND MAINTENANCE MANUAL GLENAYRE LYNX.sc E1 FAMILY Western Multiplex SPREAD SPECTRUM RADIOS SEPTEMBER 1999 W 3.10 Antenna Installation & Alignment Structures to provide 5 meters or more separation from all persons during device operation to comply with FCC RF exposure requirements. Please contact Western Multiplex factory for applicable gain and type restrictions to ensure compliance.

@ Antennas used for this device must be fix-mounted on permanent outdoor The antenna installation consists of mounting the antenna on the tower, building roof, or other location that provides line-of-sight path clearance to the far-end location. In general, antennas smaller than 2 feet diameter are not recommended for urban areas due to their wider beam widths, which results in higher interference susceptibility. For 2.4 GHz LYNX.sc radios, a minimum of 4 foot (1.2m) diameter antennas, or larger, are recommended. Antennas should be ordered with a suitable mounting kit specific to the site requirements. For example, specifying round or angle tower leg adapters, or a roof tripod as necessary. The antenna must be very rigidly mounted, with adequate room for azimuth and elevation adjustment. The antenna polarization must be the same at both ends of the link, either vertical or horizontal. In general, antenna mountings require a support pipe to which upper and lower support brackets are attached with U bolts. The antenna and optional elevation and azimuth adjustment rods are then mounted onto the support brackets. The whole structure must be adequately grounded for lightning protection. The antenna system must always be installed according to the manufacturers instructions. Unless special test equipment is available, two operating LYNX.sc terminals are required to align the antennas. Alternatively, a CW generator may be used to transmit a signal toward the end under alignment. The antenna is coarse aligned using visual Sighting and then fine aligned using the receive signal level (RSL) voltage of the LYNX.sc. The RSL voltage reading can still be used to peak antennas cS even if the radios have not synchronized, however far-end RSL cannot be measured from the near-end terminal until radios are synchronized. To coarse align the antenna, first set it for flat elevation (no up or down tilt) using a spirit level. Then point it at a heading marker obtained using a compass back-bearing from an adjacent location, (ideally, 100 feet or more away from the antenna). PAGE 3-22 SECTION 3: INSTALLATION & ADJUSTMENTS

 

 

INSTALLATION AND MAINTENANCE MANUAL 1xE1, 2xE1 AND 4xE1 (2.048 Mbps) SPREAD SPRECTRUM RADIOS

(2.4 AND 5.8 GHz) INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS NOVEMBER 1999 Installation and Maintenance Manual Copyright 1998 by Western Multiplex Corporation. All rights reserved. No part of this manual may be reproduced without prior written permission from Western Multiplex Corp. The information contained in this manual is subject to change without notice. Western Multiplex shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this manual or equipment supplied with this manual. Western Multiplex makes no warranty of any kind with regard to this manual or any equipment supplied with this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Heliax Fireberd is a registered product of Telecommunications Techniques Corporation. is a registered product of Andrews Corporation. Printed in the United States of America Notice: Y2K (Year 2000 Issue) All software supplied by and for Western Multiplex products adheres to the four-(4) digit year nomenclature as required for Year 2000 compliance. Western Multiplex Corporation 1196 Borregas Avenue Sunnyvale, California USA

+1 408 542-5200 Tel:

Fax:: +1 408 542-5300 Our facility has been Registered to the International Organization for Standardization ISO 9000 Series Standards for quality. Issue: November 1999 i INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS NOVEMBER 1999 This page intentionally left blank ii INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS NOVEMBER 1999 Regulatory Notice This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Shielded cables and I/O cords must be used for this equipment to comply with the relevant FCC regulations. Changes or modifications not expressly approved in writing by Western Multiplex may void the user's authority to operate this equipment. This device complies with RSS-210 and/or RSS-139 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This device must be professionally installed. iii INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS NOVEMBER 1999 This page intentionally left blank iv INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS NOVEMBER 1999 WARRANTY GENERAL TERMS 1.1 All Definitions contained in Western Multiplex's Conditions of Sale (Western Multiplex document number CS96-8), apply to the Warranty . 1.2 Subject to the provisions of the Warranty, Western Multiplex warrants that the equipment described in Paragraph 1.3 shall conform to their specifications described in Paragraph 1.4 in all material respects and that the equipment shall be free from material defects in materials and workmanship. 1.3 This Warranty applies to all original purchases of Western Multiplex manufactured equipment and accessories (collectively the "Equipment"). 1.4 This Warranty applies to the specifications contained in the most recent version of the manual for the model of the Equipment purchased (the "Specifications"). 1.5 This Warranty does not apply to the following items of Equipment which are covered by the Original Equipment Manufacturer's warranty:

(a)

(b)

(c) antenna systems, including coax cable, waveguide, connectors flex-sections, mounts, other parts of the antenna system and installation materials;

non-Western Multiplex manufactured rack mounted equipment that is assembled wired and tested at Western Multiplex's factory or supplied as part of a system, including orderwire items, channel banks, multiplexers, fuse/alarm panels, remote alarm items; and equipment which is not listed in Western Multiplex's price book. 1.6 The effective period of this Warranty shall start on the date of shipment of the Equipment and shall end:

(a)

(b)

(c) for all spread spectrum unlicensed radio products and for all licensed digital microwave radio products, two (2) years later;

for all analog microwave radio products, three (3) years later;

or for all baseband products, five (5) years later (in each case the "Warranty Period"). 1.7 The Customer acknowledges that Western Multiplex does not represent or warrant that the services provided by Western Multiplex under this Warranty will ensure uninterrupted or error-

free operation of the Equipment. RETURN OF EQUIPMENT UNDER WARRANTY 2.1 If an item of Equipment malfunctions or fails in normal intended usage and maintenance within the applicable Warranty Period:

(a) the Customer shall promptly notify Western Multiplex of the problem and the serial number of the defective item;

(c)

(b) Western Multiplex shall, at its sole option, either resolve the problem over the telephone or provide the Customer with a Returned Materials Authorization number (RMA #) and the address of the location to which the Customer may ship the defective item;

if the problem is not resolved over the telephone, the Customer shall attach a label to each Returned item describing the fault and the Customer's Return address. The Customer shall, at its cost, properly pack the item to be Returned, prepay the insurance and shipping charges, and ship the item to the specified location;

if the Western Multiplex product shall prove to be defective in material or workmanship upon examination by Western Multiplex, Western Multiplex shall either repair or replace the Returned item at its sole option. The replacement item may be new or refurbished; if refurbished, it shall be equivalent in operation to new Equipment. If a Returned item is replaced by Western Multiplex, the Customer agrees that the Returned item shall become the property of Western Multiplex.

(d)

(e) Western Multiplex shall at its cost, ship the repaired item or replacement to any destination within the United States of America by carrier and method of delivery chosen by Western Multiplex. If the Customer has requested some other form of conveyance, such as express shipping, or is located beyond the USA borders, then the Customer shall pay to the cost of return shipment. 2.2 Equipment which is repaired or replaced by Western Multiplex under this Warranty shall be covered under all of the provisions of this Warranty for the remainder of the applicable Warranty Period or ninety (90) days from the date of shipment of the repaired item or replacement, whichever period is longer. DEFAULT AND TERMINATION 3.1 Western Multiplex may immediately terminate this Warranty and all of its performance under this Warranty, upon notification to the Customer, if the Customer:

(a) makes any unauthorized modifications to the Equipment;

(b) assigns or transfers the Customer's rights or obligations under this Warranty without the written consent of Western Multiplex;

becomes bankrupt or insolvent, or is put into receivership; or has not paid Western Multiplex all amounts for the Equipment, services, or other additional charges within thirty (30) days of receipt of written notice from Western Multiplex.

(c)

(d) 3.2 If this Warranty is terminated by Western Multiplex, the Customer shall remain liable for all amounts due to Western Multiplex. FORCE MAJEURE 4.1

"Force Majeure" has the same meaning as defined in Western Multiplex's Conditions of Sale (Western Multiplex document number CS96-8). Western Multiplex shall not be responsible for failure to discharge its obligations under this Warranty due to Force Majeure. 4.2 LIMITATIONS AND QUALIFICATIONS OF WARRANTY 5.1 This Warranty does not apply to any damage, defect or failure caused by:

(a) any part of the Equipment having been modified, adapted, repaired, or improperly installed, operated, maintained, transported or relocated by any person other than Western Multiplex personnel or a Western Multiplex authorized service agent, without Western Multiplex's prior written consent;

storage or environmental conditions which do not conform to the applicable sections of the appropriate Western Multiplex Equipment Manual;

failure to conform with the Equipment Installation, Operating and Maintenance Instructions of the appropriate Western Multiplex Equipment Manual;

external causes, including external electrical stress or lightning, or use in conjunction with incompatible equipment, unless such use was with Western Multiplex's prior written consent;

cosmetic damage;

accidental damage, negligence, neglect, mishandling, abuse or misuse, other than by Western Multiplex personnel or a Western Multiplex authorized service agent; or

(b)

(c)

(d)

(e)

(f)

(g) Force Majeure. Please see reverse side for additional limitations on damages. v W/CS97-1 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS NOVEMBER 1999 LIMITATIONS ON DAMAGES (North America) 6.1 THE WARRANTY STATED IN THIS DOCUMENT IS THE LIMITATIONS ON DAMAGES (International) 6.1 THE WARRANTY STATED IN THIS DOCUMENT IS THE CUSTOMER'S EXCLUSIVE WARRANTY FOR THE EQUIPMENT; WESTERN MULTIPLEX SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND OF MERCHANTABILITY. CUSTOMER'S EXCLUSIVE WARRANTY FOR THE EQUIPMENT; ALL OTHER WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND OF MERCHANTABILITY ARE EXCLUDED TO THE FULLEST EXTENT PERMITTED BY LAW. 6.2 WESTERN MULTIPLEX SHALL NOT BE LIABLE IN TORT, 6.2 WESTERN MULTIPLEX'S LIABILITY FOR FAILURE TO INCLUDING LIABILITY IN NEGLIGENCE OR STRICT LIABILITY, AND SHALL HAVE NO LIABILITY AT ALL FOR INJURY TO PERSONS OR PROPERTY. WESTERN MULTIPLEX'S LIABILITY FOR FAILURE TO FULFIL ITS OBLIGATIONS UNDER THIS WARRANTY OR ANY OTHER LIABILITY UNDER OR IN CONNECTION WITH THE EQUIPMENT SHALL BE LIMITED TO THE AMOUNT OF THE PURCHASE PRICE OF THE EQUIPMENT. THE REMEDIES STATED IN THIS WARRANTY ARE THE CUSTOMER'S EXCLUSIVE REMEDIES AGAINST WESTERN MULTIPLEX REGARDING THE EQUIPMENT. FULFIL ITS OBLIGATIONS UNDER THIS WARRANTY OR IN TORT OR AS A RESULT OF STRICT LIABILITY OR ANY OTHER LIABILITY UNDER OR IN CONNECTION WITH THE EQUIPMENT OR ITS SUPPLY SHALL BE LIMITED, EXCEPT IN RESPECT OF DEATH AND PERSONAL INJURY CAUSED BY WESTERN MULTIPLEX'S NEGLIGENCE, TO THE AMOUNT OF THE PURCHASE PRICE OF THE EQUIPMENT. THE REMEDIES STATED IN THIS WARRANTY ARE THE CUSTOMER'S EXCLUSIVE REMEDIES AGAINST WESTERN MULTIPLEX REGARDING THE EQUIPMENT. 6.3 EVEN IF WESTERN MULTIPLEX HAS BEEN ADVISED OF 6.3 EVEN IF WESTERN MULTIPLEX HAS BEEN ADVISED OF THE POSSIBILITY OF THEM, WESTERN MULTIPLEX SHALL NOT BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, INCLUDING THE COST OF LABOR BY THE CUSTOMER'S OWN EMPLOYEES, AGENTS OR CONTRACTORS IN IDENTIFYING, REMOVING OR REPLACING THE DEFECTIVE ITEM; LOST PROFITS, AND REVENUES;

FAILURE TO REALIZE EXPECTED SAVINGS; ANY CLAIM AGAINST A CUSTOMER BY A THIRD PARTY; OR ANY OTHER COMMERCIAL OR ECONOMIC LOSSES OF ANY KIND. 6.4 THESE LIMITATIONS AND DISCLAIMERS ARE NOT MADE BY WESTERN MULTIPLEX WHERE PROHIBITED BY LAW. THE POSSIBILITY OF THEM, WESTERN MULTIPLEX SHALL NOT BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, INCLUDING THE COST OF LABOR BY THE CUSTOMER'S OWN EMPLOYEES, AGENTS OR CONTRACTORS IN IDENTIFYING, REMOVING OR REPLACING THE DEFECTIVE ITEM; LOST PROFITS, AND REVENUES;

FAILURE TO REALIZE EXPECTED SAVINGS; ANY CLAIM AGAINST A CUSTOMER BY A THIRD PARTY; OR ANY OTHER COMMERCIAL OR ECONOMIC LOSSES OF ANY KIND. W/CS97-1 vi INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS NOVEMBER 1999 CONDITIONS OF SALE DEFINITIONS 1.1

(a)

(b)

(c)

(d)

(e)

(f)

(g)

(h)

(i)

(j) the on the itemized equipment In these Conditions, unless there is something in the subject matter or context necessarily inconsistent:

"Western Multiplex" means Western Multiplex (d.b.a. Western Multiplex), Sunnyvale, CA;

"Equipment" means Quotation/Order Acknowledgment;

"International" means any location other than United States of America and Canada, including their territories and possessions;

"North America" means any location in the United States of America and Canada, including their territories and possessions;

"Order Acknowledgment" means the sales order acknowledgment provided by Western Multiplex to the Customer;

"Payment instructions, (Western Multiplex document P197-1);

"Quotation" means representative of Western Multiplex and provided Customer;

"Shipping Date" means the actual date on which the Equipment left Western Multiplex's factory at Sunnyvale, CA, U.S.A.;

"Warranty" means Western Multiplex's warranty, document W97-

1;

"Invoice" means the bill of goods prepared by Western Multiplex for the equipment with the shipping and any insurance costs. these Conditions the quotation signed by an authorized the Instructions" means Western Multiplex's payment inserted to in convenience of construction. reference only and will not effect for their 1.2 Headings have been ENTIRE AGREEMENT 2.1 The Quotation, these Conditions of Sale, the Order Acknowledgment, the Payment Instructions and the Warranty shall apply to all sales made by Western Multiplex and shall constitute the entire agreement by Western Multiplex and the Customer (the "Agreement "). 2.2 Any terms and/or conditions of sale, which may be included on the Customer's purchase order form or any communication from the Customer, that are not identical with the terms and conditions steed in this document shall NOT become a part of the agreement of sale unless expressly agreed to in writing in the Quotation. 2.3 Western Multiplex's failure to object terms and/or conditions of sale contained in any communication from the Customer shall not be considered as acceptance of such terms and/or conditions or as a waiver of the terms and conditions of sale contained herein. to any from Western Multiplex, 2.4 Western Multiplex shall sell to the Customer, and the Customer in shall purchase accordance with the Agreement. Western Multiplex accepts the Customer's purchase orders for Equipment and agrees to deliver the Equipment to the Customer only on the terms of the Agreement. the Equipment 2.5 No variation of the Agreement shall be binding unless agreed to in writing by authorized representatives of Western Multiplex and the Customer. PRICING 3.1 All prices in the Quotation are exclusive of all shipping charges and all applicable taxes including but not limited to, federal, state, local, excise, sales and use taxes. 3.2 All prices in the Quotation unless otherwise stated:

(a)

(b) for North American customers are FOB Sunnyvale, CA, USA. (New York Uniform Commercial Code); or for international customers are Ex-Works, Sunnyvale, CA, U.S.A. (Incoterms 1990). 3.3 All prices in the Quotation include standard domestic packing, unless a separate line item is provided detailing export or special packing charges. SHIPPING AND INSURANCE 4.1 Western Multiplex shall arrange shipping and insurance when requested by the Customer, and shall bill the Customer for the Equipment with the shipping and any insurance costs as separate items, on an invoice (the "Invoice"). 4.2 Delivery dates quoted by Western Multiplex are to be considered estimates only. In no event will Western Multiplex be liable for any loss or damage resulting from its failure to deliver products within a specified time. TERMS OF PAYMENT 5.1 The Customer shall pay for all Equipment, including shipping and insurance in accordance with the terms of the Invoice. 5.2 All Invoices for North American Customers are due and payable 5.3

(a)

(b) 5.4 in thirty (30) days from the date of the Invoice. International Customers shall make payments in accordance with Western Multiplex's Payment Instructions by either:

providing a wire transfer (telegraphic transfer) for the full amount of the Equipment, shipping and insurance charges contained in the Quotation or the pro-forma Invoice sent to the Customer, prior to the Shipping Date; or establishing an acceptable Letter of Credit (LC) for the full amount of the Equipment, shipping and insurance charges contained in the Quotation prior to the order being booked and accepted by Western Multiplex. If a Customer fails to pay an Invoice when due, Western Multiplex may, without prejudice to am other remedy, postpone shipments, alter payment terms, terminate the Agreement and charge interest on all overdue amounts the rate of 1.5% per month compounded monthly (or if less, the maximum allowed by law). Upon demand, the Customer shall pay all such interest charges and all reasonable collection fees, including reasonable legal expenses. SECURITY FOR PAYMENT 6.1 6.2

(a)

(b)

(i)

(ii)

(iii) If the Customer is located in North America, the Customer grants to Western Multiplex a purchase money security interest in the Equipment to secure the payment of the purchase price of the Equipment and all other amounts due from the Customer. If the Customer is not located in North America:

despite delivery and passing of risk in the Equipment and any other provision of these Conditions, the title in the Equipment shall not pass to the Customer until Western Multiplex has received payment in full of the purchase price of the Equipment and all other amounts then due from the Customer, and until the title in the Equipment passes to the Customer:

the Customer shall hold the equipment as Western Multiplex 's fiduciary agent and bailee, and shall properly store, protect and insure the Equipment and shall identify the Equipment as Western Multiplex property;

if the Customer fails to pay Western Multiplex in accordanc e with the agreed payment terms, Western Multiplex may require the Customer to deliver up the Equipment to Western Multiplex, and, if the Customer does not, Western Multiplex may enter on the premises where the Equipment is stored and repossess the Equipment; and the Customer shall not pledge the Equipment by way of security for any, indebtedness of the Customer, but if the Customer does so all moneys owed by the Customer to Western Multiplex shall, without prejudice to any other remedy of Western Multiplex, immediately become due. CHANGES TO PRODUCT SPECIFICATIONS 7.1 Western Multiplex may, without notice to the Customer, make the specifications of Equipment which do not changes materially affect the quality or performance of the Equipment. to EQUIPMENT CONFIGURATION AND EXPEDITING CHARGES vii W/CS97-1 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS NOVEMBER 1999 8.1 At the Customer's request, Western Multiplex may, for a fee agreed in advance:

reconfigure the Equipment; or expedite the Customer's order.

(a)

(b) W/CS97-1 viii INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS NOVEMBER 1999 SHORTAGES 9.1 The customer shall not make any claim for shortages (which are items that the Invoice does not show are on back-order) after twenty-one (21) days after the date of the Invoice.

(b) RETURNS AND EXCHANGES 10.1 The return of defective Equipment is covered by the Warranty . 10.2 The Customer may only return Equipment that is not defective if:

(a) the Customer's the Equipment does not correspond with purchase order; or the Equipment has been ordered in error by the Customer and Western Multiplex has permitted the Customer to remedy the mistake by ordering the correct equipment and resuming the Equipment and the Customer obtains a Returned Materials Authorization number ("RMA #") from Western Multiplex prior to returning any Equipment. 10.3 Western Multiplex reserves the right to charge a fee for returned equipment under Subparagraph 10.2(b) with the amount of the fee being determined prior to an RMA # being given by Western Multiplex. 10.4 Authorized returns of equipment under Paragraph 10.2 must be in an undamaged condition, in the original configuration, in the original packing materials and within a time period agreed to when the RMA # was issued. 10.5 If the Customer does not comply with the provisions of Paragraphs 10.2, 10.3, and 10.4, the Customer shall pay the full amount of the Invoice. 10.6 The party liable for all shipping, insurance and any other expenses incurred by the Customer in returning the Equipment under Paragraph 10.2 and the Equipment until received by Western Multiplex, shall be: (a) for all items returned under Subparagraph 10.2(a), Western Multiplex and (b) for all items resumed under Subparagraph 10.2(b), the Customer. loss or damage for all to CANCELLATION 11.1 If the Customer cancels an order before the Shipping Date, Western Multiplex reserves the right to charge the Customer a cancellation charge up to 100% of the amount of the order. 11.2 The Customer shall pay all cancellation charges within thirty (30) days from date of the Invoice. impractical due FORCE MAJEURE 12.1 Western Multiplex shall not be liable if its performance of the Agreement becomes commercially to any contingency beyond Western Multiplex's reasonable control, including acts of God, fires, floods, wars, sabotage, civil unrest, accidents, labor disputes or shortages, government laws, rules and regulations, whether valid or invalid, inability to obtain material, equipment or incorrect, delayed or incomplete specifications, drawings or data supplied by the Customer or others (collectively "Force Majeure"). In no event of Force Majeure shall Western Multiplex be required to purchase goods from others to enable it to deliver the Equipment under the Agreement. transportation, ENGINEERING AND SYSTEM DESIGN 13.1 The Customer is solely responsible for the engineering, design, integration and normal preventative and remedial maintenance of the Customer's system for which Western Multiplex supplies Equipment. the Equipment 13.2 Western Multiplex is not responsible for the satisfactory operation of in conjunction with other manufacturer's equipment, nor for any losses which may occur as a result of a failure of the Equipment to operate in conjunction with other manufacturer's equipment. WARRANTY 14.1 All Equipment is covered by the Warranty. 14.2 THE WARRANTY CONTAINS LlMITATIONS ON THE CUSTOMER'S RIGHTS AND REMEDIES AGAINST WESTERN MULTIPLEX AGREEMENT. ACKNOWLEDGES HAVING READ, THE CUSTOMER UNDERSTOOD AND AGREED TO THOSE LIMITATIONS. UNDER THE DAMAGES FOR BREACH OF AGREEMENT 15.1 If either party is successful in any litigation between the parties based on the Agreement, the successful party shall recover from the other, in addition to direct damages, the successful party's reasonable attorney's fees and other costs of litigation. INSOLVENCY OF CUSTOMER, ETC. 16.1 Western Multiplex may cancel the Agreement and suspend any further deliveries under the Agreement without any liability to the Customer, and, if Equipment has been delivered but not paid for, the price shall become immediately due and payable despite any other agreement to the contrary if:

(a)

(b)

(c)

(d)

(e) any proceedings in bankruptcy, insolvency, receivership or liquidation are taken against the Customer;

the Customer makes an assignment for the benefit of creditors or commits an act of bankruptcy or insolvency;

the Customer ceases, or threatens to cease, to carry on transfers all or its business, or the ordinary course of substantially all of its property;

the Equipment is seized under any legal process or confiscated; or Western Multiplex in good faith believes that the ability of the Customer to pay or perform any provision of the Agreement is impaired, or that any of the events mentioned above is about to occur. NOTICE 17.1 All requests, instructions and notices from one party to the other must be in writing and may be given via registered post or facsimile transmission to the address of the parties shown on the Quotation or Order Acknowledgment. EXPORT PROVISIONS 18.1 The Customer shall not, whether directly or indirectly (including facilitating a third party) export or re-export the Equipment outside the country in which the Customer has stated these items are to be used without obtaining the licenses required under ail applicable rules. The Customer shall indemnify Western Multiplex against any liability incurred by Western Multiplex due to any violation by the Customer of any of the provisions of this Section, but this indemnity shall not apply if the Customer reasonably relies on information supplied to it by Western Multiplex with respect to export licenses. Upon receipt of a governmental consent the receiving party shall immediately notify the other in writing. to export MISCELLANEOUS 19.1 No waiver by Western Multiplex of any breach of this Agreement shall be considered as a waiver of any subsequent breach of the same or any other provision. 19.2 Any provision of the Agreement which is, or is deemed to be, unenforceable in any jurisdiction shall be severable from the Agreement in that jurisdiction without in any way invalidating the remaining portions of the Agreement, and that unenforceability shall not make in any other jurisdiction. that provision unenforceable 19.3 The rights which accrue to Western Multiplex by virtue of the Agreement shall inure for the benefit of and be binding upon the successors and assigns of Western Multiplex. 19.4 The agreement shall be governed by the laws of the State of California including the California Uniform Commercial Code. However Western Multiplex may enforce the provisions of the Agreement in accordance with the laws of the jurisdiction in which ix W/CS97-1 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS NOVEMBER 1999 the Equipment is situated. The United Nations Convention on the Sale of Goods (The Vienna Convention) shall not apply to the Agreement. 19.5 Les parties ont exigs que cette entente soit rdige en anglais. W/CS97-1 x INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Table of Contents 1. HOW TO USE THIS MANUAL........................................................................................................................................1-1 1.1 1.2 MANUAL ORGANIZATION......................................................................................................................................... 1-1 ICONS............................................................................................................................................................................. 1-2 2. PRODUCT DESCRIPTION.............................................................................................................................................2-1 2.1 2.2 2.3 2.4 2.5 3.1 3.2 3.3 GENERAL DESCRIPTION................................................................................................................................................ 2-1 SPECIFICATIONS............................................................................................................................................................ 2-2 2.2.1 Transmitter.........................................................................................................................................................2-2 2.2.2 Antenna / Antenna Coupling Unit................................................................................................................2-3 2.2.3 Receiver..............................................................................................................................................................2-4 2.2.4 System (Single Hop Performance).............................................................................................................2-5 2.2.5 Digital Line Interface.......................................................................................................................................2-7 2.2.6 Auxiliary Connections .....................................................................................................................................2-8 2.2.7 Temperature and Environment .......................................................................................................................2-9 2.2.8 Power...................................................................................................................................................................2-9 2.2.9 Regulatory Information................................................................................................................................. 2-10 2.2.10 Mechanical...................................................................................................................................................... 2-10 FRONT PANEL DESCRIPTION..................................................................................................................................... 2-11 General............................................................................................................................................................. 2-11 Test Points / Power Indicator.................................................................................................................... 2-12 Alarm and Status Indicators...................................................................................................................... 2-13 Controls............................................................................................................................................................ 2-14 Connections.................................................................................................................................................... 2-15 REAR PANEL DESCRIPTION....................................................................................................................................... 2-16 RF Connection............................................................................................................................................... 2-17 DATA Connections....................................................................................................................................... 2-18 Auxiliary Data Connections ........................................................................................................................ 2-19 Switches .......................................................................................................................................................... 2-20 INSTALLATION ACCESSORIES.................................................................................................................................... 2-22 2.3.1 2.3.2 2.3.3 2.3.4 2.3.5 2.4.1 2.4.2 2.4.3 2.4.4 3. INSTALLATION & ADJUSTMENTS...........................................................................................................................3-1 SHIPPING CONTAINER................................................................................................................................................... 3-1 PACKING ITEMS IDENTIFICATION.................................................................................................................................. 3-2 BEFORE INSTALLATION TASK LIST............................................................................................................................. 3-3 Site Selection Requirements........................................................................................................................3-3 Line-of-Sight and Path Clearance Guidelines .........................................................................................3-4 RSL Calculation and Link Budget...............................................................................................................3-5 Fade Margin Calculation ................................................................................................................................3-6 Availability Calculation ...................................................................................................................................3-7 Frequency Plan Determination.....................................................................................................................3-8 Power Supply Planning...................................................................................................................................3-9 Antenna Planning.......................................................................................................................................... 3-10 TOOLS REQUIRED....................................................................................................................................................... 3-11 3.3.1 3.3.2 3.3.3 3.3.4 3.3.5 3.3.6 3.3.7 3.3.8 3.4 TOC & INTRODUCTION i INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS NOVEMBER 1999 3.7.1 3.7.2 3.5 FREQUENCY CHANNEL PLANS ................................................................................................................................. 3-12 3.6 MOUNTING THE LYNX.SC......................................................................................................................................... 3-15 POWER CONNECTION AND WIRING........................................................................................................................... 3-16 3.7 DC Power Wiring........................................................................................................................................... 3-17 AC Power Connection.................................................................................................................................. 3-19 ANTENNA CONNECTION.............................................................................................................................................. 3-20 3.8 3.9 TRANSMISSION LINE CONNECTION............................................................................................................................ 3-21 3.10 ANTENNA INSTALLATION & ALIGNMENT.................................................................................................................. 3-22 3.11 CEPT-1 (E1) INTERFACECONNECTION.................................................................................................................. 3-25 3.12 DIP SWITCH SETTINGS............................................................................................................................................ 3-26 3.12.1 Channel Selection......................................................................................................................................... 3-26 3.12.2 Loopback Test Signal Selection.............................................................................................................. 3-27 3.12.3 Spreading Code Selection.......................................................................................................................... 3-28 3.12.4 Input Alarm (Data Loss) Enable/Disable............................................................................................... 3-29 3.12.5 AIS Enable/Disable ..................................................................................................................................... 3-30 3.13 SYSTEM TURN-UP TO SERVICE................................................................................................................................. 3-31 3.13.1 Output Power Adjustment .......................................................................................................................... 3-39 3.13.2 Loopback/BER Testing .............................................................................................................................. 3-40 3.13.3 Error LED Mode Selection.......................................................................................................................... 3-42 3.14 ADDITIONAL CONNECTIONS ....................................................................................................................................... 3-43 3.14.1 Orderwire Connection and Address Selection...................................................................................... 3-43 3.14.2 Alarm Connections ....................................................................................................................................... 3-46 3.14.3 Diagnostics Port Operation ......................................................................................................................... 3-48 3.14.3.1 Diagnostics Port using RS-232............................................................................................................ 3-49 3.14.3.2 Diagnostics Port using RS-422............................................................................................................ 3-50 TBOS Protocol and Map ........................................................................................................................ 3-51 3.14.3.3 3.14.4 AUX DATA (Digital Service Channel) Connection................................................................................. 3-53 3.14.5 Protect Port Connection (Preliminary Information)............................................................................. 3-56 3.14.6 Protect Port Connection (Preliminary Information)............................................................................. 3-57 4. TROUBLESHOOTING.....................................................................................................................................................4-1 4.1 4.2 4.3 4.4 4.5 4.6 REGULAR MAINTENANCE............................................................................................................................................. 4-1 CHANGING FREQUENCY PLANS................................................................................................................................ 4-2 USING A SPARE TERMINAL.......................................................................................................................................... 4-3 TECHNICAL SUPPORT................................................................................................................................................... 4-4 REPAIR POLICY............................................................................................................................................................. 4-5 FRONT PANEL STATUS LEDS.................................................................................................................................... 4-6 DATA LOSS Alarms.......................................................................................................................................4-7 BER (Bit Error Rate) Alarm...........................................................................................................................4-9 RX SYNC (Receiver Synchronization) Alarm....................................................................................... 4-12 AIS OUT (Alarm Indication Signal) ......................................................................................................... 4-13 FAN Alarm ...................................................................................................................................................... 4-14 RADIO FAIL Alarm....................................................................................................................................... 4-15 FAR END Alarm............................................................................................................................................ 4-16 ERRORS IN THE DATA STREAM................................................................................................................................ 4-17 INTERFERENCE COUNTERMEASURES......................................................................................................................... 4-19 Use of a Spectrum Analyzer to Evaluate Potential Interference.................................................... 4-21 BACK-TO-BACK TESTING.......................................................................................................................................... 4-22 4.9 4.10 BER (BIT ERROR RATE) TESTING........................................................................................................................... 4-24 4.6.1 4.6.2 4.6.3 4.6.4 4.6.5 4.6.6 4.6.7 4.7 4.8 4.8.1 5. APPENDICES.....................................................................................................................................................................5-1 ii TOC & INTRODUCTION INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 APPENDIX A - DIGITAL LINE INTERFACE SPECIFICATIONS...................................................................................................... 5-1 1. General Characteristics............................................................................................................................................5-1 Specifications at the output ports ...........................................................................................................................5-1 2. APPENDIX B - REAR PANEL DIP SWITCHES.......................................................................................................................... 5-3 APPENDIX C - REAR PANEL DATA CONNECTORS................................................................................................................. 5-9 Figures FIGURE 2-1: FRONT PANEL, 2.4 GHZ & 5.8 GHZ 1XE1......................................................................................................... 2-11 FIGURE 2-2: FRONT PANEL, 2.4 GHZ & 5.8 GHZ 2XE1......................................................................................................... 2-11 FIGURE 2-3: FRONT PANEL, 2.4 GHZ & 5.8 GHZ GHZ 4XE1................................................................................................ 2-11 FIGURE 2-4: REAR PANEL, 1XE1............................................................................................................................................... 2-16 FIGURE 2-5: REAR PANEL, 2XE1............................................................................................................................................... 2-16 FIGURE 2-6: REAR PANEL, 4XE1............................................................................................................................................... 2-16 FIGURE 2-7: CEPT-1 INTERFACE GROUNDING SWITCH........................................................................................................ 2-18 FIGURE 3-1: CHANNEL PLAN, 2.4 GHZ 1XE1........................................................................................................................... 3-12 FIGURE 3-2: CUSTOM CHANNEL PLAN, 2.4 GHZ E1............................................................................................................... 3-12 FIGURE 3-3: CHANNEL PLAN, 2.4 GHZ 2XE1........................................................................................................................... 3-13 FIGURE 3-4: CHANNEL PLAN, 5.8 GHZ 1XE1........................................................................................................................... 3-13 FIGURE 3-5: CHANNEL PLAN, 5.8 GHZ 2XE1........................................................................................................................... 3-14 FIGURE 3-6: CHANNEL PLAN, 5.8 GHZ 4XE1........................................................................................................................... 3-14 FIGURE 3-7: NEGATIVE VOLTAGE DC CONNECTION............................................................................................................ 3-18 FIGURE 3-8: POSITIVE VOLTAGE DC CONNECTION.............................................................................................................. 3-18 FIGURE 3-9: AC CONNECTION.................................................................................................................................................. 3-19 FIGURE 3-10: TYPICAL RSL VOLTAGE VERSUS RECEIVED SIGNAL LEVEL (RSL)............................................................. 3-24 FIGURE 3-11: CEPT-1 INTERFACE GROUNDING SWITCH...................................................................................................... 3-25 FIGURE 3-12: LOOPBACK MODE SELECTION......................................................................................................................... 3-27 FIGURE 3-13: SPREADING CODE SELECTION ......................................................................................................................... 3-28 FIGURE 3-14: INPUT ALARM DISABLE SWITCH .................................................................................................................... 3-29 FIGURE 3-15: AIS SWITCH......................................................................................................................................................... 3-30 FIGURE 3-16: TYPICAL RF OUTPUT POWER VERSUS PWR VOLTAGE, 2.4 GHZ MODELS.............................................. 3-33 FIGURE 3-17: TYPICAL RF OUTPUT POWER VERSUS PWR VOLTAGE, 5.8 GHZ MODELS.............................................. 3-34 FIGURE 3-18: ERROR LED MODE SELECTION ........................................................................................................................ 3-42 FIGURE 3-19: RJ-11 ORDERWIRE TELEPHONE CONNECTION.............................................................................................. 3-44 FIGURE 3-20: VF PORT CONNECTION...................................................................................................................................... 3-45 FIGURE 3-21: PIN CONNECTIONS, ALARM INTERFACE....................................................................................................... 3-46 FIGURE 3-22: DIAGNOSTIC PORT PROTOCOL SELECTION................................................................................................... 3-48 FIGURE 3-23: RS-232 DIAGNOSTIC PORT CONNECTIONS..................................................................................................... 3-49 FIGURE 3-24: RS-422 DIAGNOSTIC PORT CONNECTIONS..................................................................................................... 3-50 FIGURE 3-25: REPEATER AND HUB TBOS RADIO NETWORK MANAGEMENT ................................................................ 3-54 FIGURE 3-26: REPEATER APPLICATION WITH SITE NETWORK MANAGEMENT ........................................................... 3-54 FIGURE 3-27: AUX DATA CABLE CONNECTION FOR REPEATER/HUB............................................................................ 3-55 FIGURE 3-28: AUX DATA SELECTION .................................................................................................................................... 3-55 FIGURE 3-29: MHS CONFIGURATION....................................................................................................................................... 3-56 FIGURE 3-30: SD CONFIGURATION........................................................................................................................................... 3-57 FIGURE 4-1: BACK-TO-BACK TEST CONFIGURATION........................................................................................................... 4-23 FIGURE 4-2: END-TO-END BER TEST CONFIGURATION........................................................................................................ 4-24 TOC & INTRODUCTION iii INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS NOVEMBER 1999 FIGURE A-1: MASK OF THE E1 PULSE (CEPT-1) ...................................................................................................................... 5-2 FIGURE C-1: VF PORT CONNECTION ......................................................................................................................................... 5-9 FIGURE C-2: ALARM PORT CONNECTIONS............................................................................................................................... 5-9 FIGURE C-3: DIAGNOSTIC PORT 9-PIN D-STYLE CONNECTOR........................................................................................... 5-10 FIGURE C-4: AUX DATA PORT 9-PIN D-STYLE CONNECTOR........................................................................................... 5-10 Tables TABLE 3-A: DC POWER CONNECTION FOR NEGATIVE SUPPLY........................................................................................ 3-16 TABLE 3-B: DC POWER CONNECTION FOR NEGATIVE SUPPLY......................................................................................... 3-16 TABLE 3-C: TRANSMITTER OUTPUT POWER ADJUSTMENT, +6 DBW EIRP INSTALLATIONS..................................... 3-37 TABLE 3-D: TRANSMITTER OUTPUT POWER ADJUSTMENT FOR 2.4 GHZ, USA INSTALLATIONS............................. 3-38 TABLE 3-E: ALARM INTERFACE CONNECTIONS................................................................................................................... 3-47 TABLE 3-F: TBOS MAP FOR THE LYNX.SC E1S..................................................................................................................... 3-52 TABLE A-2: CEPT-1 INTERCONNECTION SPECIFICATION.................................................................................................... 5-1 TABLE B-1: LYNX.SC 2.4 GHZ 1XE1, 2XE1 & 4XE1 SWITCH SETTINGS .............................................................................. 5-4 TABLE B-2: LYNX.SC 2.4 GHZ 2XE1 SWITCH SETTINGS........................................................................................................ 5-5 TABLE B-3: LYNX.SC 5.8 GHZ 1XE1 SWITCH SETTINGS........................................................................................................ 5-6 TABLE B-4: LYNX.SC 5.8 GHZ 2XE1 SWITCH SETTINGS....................................................................................................... 5-7 TABLE B-5: LYNX.SC 5.8 GHZ 4XE1 SWITCH SETTINGS........................................................................................................ 5-8 iv TOC & INTRODUCTION INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 1. How to Use This Manual 1.1 Manual Organization The Installation and Maintenance Manual provides information required to install and maintain the LYNX.sc and to use its many features to the fullest advantage. This manual is divided into the following sections:

Section 1 Provides instructions on how to most effectively utilize the information in this manual. Section 2 Provides a brief description and specifications of the LYNX.sc. Section 3 Explains the LYNX.sc installation and adjustments in detail. Section 4 Provides maintenance, repair and troubleshooting information for the LYNX.sc Spread Spectrum radios. Appendices Charts and diagrams are provided for radio connections and DIP switch settings along with other general information. This device must be professionally installed. Instructions on setting the transmitter RF output power are contained in Section 3 of this Manual. This device is to be used exclusively for fixed point-to-point operation that employs directional antennas. SECTION 1: HOW TO USE THIS MANUAL PAGE 1-1 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 1.2 Icons Throughout this manual, the following icons are used to highlight areas of special interest and importance. Note Practical Tip Caution PAGE 1-2 SECTION 1: HOW TO USE THIS MANUAL INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 2. Product Description 2.1 General Description The LYNX.sc Spread Spectrum radios provide a new level of control and convenience in a digital communications network. The LYNX.sc radios carries up to four E1 signals between two locations without the delay and expense of installing cable or traditional microwave. Because each owner controls the operation of the link, there is no reliance on any outside services. LYNX.sc radio operators are able to operate instant links whenever needed, and to be in control of their own network. The LYNX.sc offers two primary benefits:

v CONVENIENCE to install and operate with no user Easy license requirements or frequency coordination in the USA. (Other countries may require a user license and/or frequency coordination). v CAPABILITY Full transparent E1 signals over any line-of-sight distance

(typically up terrain and governmental regulations). to 50 miles, depending on SECTION 2: PRODUCT DESCRIPTION PAGE 2-1 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 2.2 Specifications All specifications are subject to change without notice. 2.2.1 Transmitter All Models Frequency Selection Rear Panel DIP switches; 7-cavity RF filter assembly Modulation OQPSK Coding Direct Sequence Number of Codes 4 (Rear Panel DIP switch selectable) Output Power (max.) Output Power (typ.) Control Range Frequency Range 2.4 GHz E1

+30 dBm*

+27 dBm*

16 dB min. 2.4 GHz 2 x E1

+30 dBm*

+27 dBm*

16 dB min. 2.4 GHz 4 x E1

+30 dBm*

+27 dBm*

16 dB min. 2410-2473 MHz

(occupies 2400-

2483.5 MHz) 2421-2462.5 MHz 2421-2462.5 MHz

(occupies 2400-

2483.5 MHz)

(occupies 2400-

2483.5 MHz)

* 10 dB less on ETSI compliant models Output Power (max.) Output Power (typ.) Control Range Frequency Range 5.8 GHz E1

+23 dBm

+20 dBm 20 dB min. 5.8 GHz 2 x E1

+23 dBm

+20 dBm 20 dB min. 5.8 GHz 4 xE1

+23 dBm

+20 dBm 20 dB min. 5735-5840 MHz

(occupies 5725-

5850 MHz) 5741-5834 MHz

(occupies 5725-

5850 MHz) 5750-5825 MHz

(occupies 5725-

5850 MHz) PAGE 2-2 SECTION 2: PRODUCT DESCRIPTION INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 2.2.2 Antenna / Antenna Coupling Unit Mechanics Antenna Connection Impedance Recommended Antenna (not included) Gain & Beamwidth (3 dB) 2 ft Antenna 4 ft Antenna 6 ft Antenna 8 ft Antenna All Models External antenna N-type female 50 ohms 2.4 GHz 4, 6, or 8 foot parabolic 5.8 GHz 2, 4, 6, or 8 foot parabolic N/A 27 dB / 7 31 dB / 5 33.5 dB / 3.5 29 dB / 6 35 dB / 3 38 dB / 2 41 dB / 1.5 SECTION 2: PRODUCT DESCRIPTION PAGE 2-3 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 2.2.3 Receiver All Models Nominal Receive Level

-30 to -60 dBm Maximum Receive Level 0 dBm error free, +10 dBm no damage Frequency Selection Rear Panel DIP switches, 7-cavity RF filter assembly Processing Gain 10 dB minimum Threshold Rx Level

(BER = 10-6) Frequency Range Threshold Rx Level

(BER = 10-6) Frequency Range 2.4 GHz 1 x E1

-93 dBm 2.4 GHz 2 x E1

-91 dBm 2.4 GHz 4 x E1

-89 dBm 2400 -

2483.5 MHz 2400 -

2483.5 MHz 2400 -

2483.5 MHz 5.8 GHz 1 x E1

-92 dBm 5.8 GHz 2 x E1

-90 dBm 5.8 GHz 4 x E1

-88 dBm 5725 -

5850 MHz 5725 -

5850 MHz 5725 -

5850 MHz PAGE 2-4 SECTION 2: PRODUCT DESCRIPTION INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 2.2.4 System (Single Hop Performance) Error Floor Dispersive Fade Margin Transmission delay

(radio only)

(10 mile path) System Gain*

--USA--

2.4 GHz**

All Models 10-11 58 dB, typical 250 m sec, maximum 300 m sec, maximum

-----------------------NO EIRP LIMIT ------------------------

2.4 GHz E1*

5.8 GHz 1xE1 5.8 GHz 2xE1 0.6m Antennas N/A 1.2m Antennas 1.8m Antennas 2.4m Antennas 166 dB 174 dB 176 dB N/A 169 dB 181 dB 181 dB 160 dB 172 dB 184 dB 184 dB 158 dB 170 dB 182 dB 182 dB

* Subtract 2 dB or 4 dB for the 2xE1 or 4xE1 models respectively Typical Link Distance*** 0.6m Antennas 1.2m Antennas 1.8m Antennas 2.4m Antennas No EIRP Limit

+6 dBW EIRP 24 km 8 km 64 km 16 km 80 km 24 km

>80 km 32 km

* Same size antenna and 30 meter inch coaxial transmission line (6.6 dB @ 5.8 GHz, 4 dB @

2.4 GHz) at each end of the link with no EIRP limits.

** (2.4 GHz EIRP limits apply in the U.S.A.)

*** Assumes 30 meter inch coaxial transmission line and same size antennas at each end. Shorter and longer link distances can be accomplished depending on transmission line quality

(and diameter), length of transmission line and other more minor factors. SECTION 2: PRODUCT DESCRIPTION PAGE 2-5 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 System (Single Hop Performance) Transmit Frequencies Channel 2.4 GHz 1xE1 2.4 GHz 4xE1 5.8 GHz 1xE1 5.8 GHz 2xE1 5.8 GHz 4xE1 A1 A2 B1 B2 C1 C2 D1 D2 E1 E2 F1 F2 2410 MHz 2453 MHz 2430 MHz 2473 MHz N/A N/A N/A N/A N/A N/A N/A N/A 2405 MHz 2446 MHz 2412 MHz 2453 MHz 2419 MHz 2460 MHz 2426 MHz 2467 MHz N/A N/A N/A N/A 5735 MHz 5800 MHz 5755 MHz 5820 MHz 5775 MHz 5840 MHz N/A N/A N/A N/A N/A N/A 5730 MHz 5795 MHz 5740 MHz 5805 MHz 5750 MHz 5815 MHz 5760 MHz 5825 MHz 5770 MHz 5835 MHz 5780 MHz 5845 MHz 5735 MHz 5800 MHz 5755 MHz 5820 MHz 5775 MHz 5840 MHz N/A N/A N/A N/A N/A N/A Receive Frequencies Channel 2.4 GHz 1xE1 2.4 GHz 4xE1 5.8 GHz 1xE1 5.8 GHz 2xE1 5.8 GHz 4xE1 A1 A2 B1 B2 C1 C2 D1 D2 E1 E2 F1 F2 2453 MHz 2410 MHz 2473 MHz 2430 MHz N/A N/A N/A N/A N/A N/A N/A N/A 2446 MHz 2405 MHz 2453 MHz 2412 MHz 2460 MHz 2419 MHz 2467 MHz 2426 MHz N/A N/A N/A N/A 5800 MHz 5735 MHz 5820 MHz 5755 MHz 5840 MHz 5775 MHz N/A N/A N/A N/A N/A N/A 5795 MHz 5730 MHz 5805 MHz 5740 MHz 5815 MHz 5750 MHz 5825 MHz 5760 MHz 5835 MHz 5770 MHz 5845 MHz 5780 MHz 5800 MHz 5735 MHz 5820 MHz 5755 MHz 5840 MHz 5775 MHz N/A N/A N/A N/A N/A N/A PAGE 2-6 SECTION 2: PRODUCT DESCRIPTION INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 2.2.5 Digital Line Interface Data Rate All Models 2.048 Mbps Digital Interface *

CEPT-1 Connector BNC female unbalanced, 75 ohm

(optional 120 ohm balanced balun available) OR RJ45/8 balanced, 120 ohm

(optional 75 ohm, unbalanced balun available) Blue Code **

Alarm Indication Signal (AIS) Remote Loopback Internal or external test signal (rear panel DIP switch selectable)

* Meets ITU-T G.703.

** Signal is selectable (on/off) and is generated only on data loss or link failure when selected. Digital Capacity 2.4 GHz 1xE1 1 x E1 2.4 GHz 2xE1 2 x E1 2.4 GHz 4xE1 4 x E1 Digital Capacity 5.8 GHz 1xE1 1 x E1 5.8 GHz 2xE1 2 x E1 5.8 GHz 4xE1 4 x E1 SECTION 2: PRODUCT DESCRIPTION PAGE 2-7 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 2.2.6 Auxiliary Connections All Models Orderwire Interface REN (Ringer Equivalency Number) DTMF tones Ringing Voltage

(use telephones with solid state ringers, NOT adequate for older style mechanical ringers) 2-wire, 4-pin modular jack, female (RJ-11) 1.0 B within 1.5% of nominal freq. 48 VDC, typical VF Orderwire Bridge 600 ohm balanced, 4-wire, 0 dBm, DB-25, male Diagnostic Port RS-232/ RS-422 (Craft / TBOS), DB-9, male Aux Data (clear service channel) RS-232 / RS-422, 9600 baud, DB-9, female Alarm Protect Port Test Points 2 x Form C, 6 x TTL, DB-25, female 8-pin modular jack female Output Power, near-end and far-end received signal level (RSL) PAGE 2-8 SECTION 2: PRODUCT DESCRIPTION INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 2.2.7 Temperature and Environment All Models Operating Temperature Range

-30 to +65C Humidity Altitude 95% non-condensing 4,500 meters, maximum 2.2.8 Power DC Input Voltage All Models 20 to 63 VDC Power Consumption

< 45 watts AC Adapter (optional) 100-250 VAC, 50-60 Hz Connector Barrier strip, plug-in type SECTION 2: PRODUCT DESCRIPTION PAGE 2-9 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 2.2.9 Regulatory Information 2.4 GHz 1xE1*

2.4 GHz 2xE1 2.4 GHz 4xE1 FCC Identifier HZB-LYNX42 FCC Rule Parts 15.247 Industry Canada ID 522 102 415A TBD 15.247 TBD TBD 15.247 TBD IC Rule Parts RSS 210 RSS 139 RSS210 ETSI ETS 300-328 & -826 ETS 300-328 & -826 5.8 GHz 1xE1*

5.8 GHz 2xE1*

5.8 GHz 4xE1*

FCC Identifier HZB-LYNX56 HZB-LYNX66 HZB-LYNX96 FCC Rule Parts 15.247 15.247 15.247 Industry Canada ID 2028 102 237 522 102 426 522 102 826 IC Rule Parts RSS 210 RSS 210 RSS 210

* Approved and/or Certified in many other countries (consult factory) 2.2.10 Mechanical Width (for 19-inch EIA rack mounting) Height Depth Weight All Models 437 mm (17.2") rack mounting brackets supplied 89 mm (3.5") (2RU) 368 mm (14.5") 5 kg. (11 lbs.) PAGE 2-10 SECTION 2: PRODUCT DESCRIPTION INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 2.3 Front Panel Description 2.3.1 General The LYNX.sc radio front panels, as shown in Figure 2-1 through 2-3, have LED indicators, test points, controls and connections that are used for installation, maintenance, operation and troubleshooting. Prior to installation, it is best to be familiar with the front panel of your particular model. Sections 2.3.2 through 2.3.5 briefly describe the front panel access and lights from left to right. Figure 2-1: Front Panel, 2.4 GHz & 5.8 GHz 1xE1 Figure 2-2: Front Panel, 2.4 GHz & 5.8 GHz 2xE1 Figure 2-3: Front Panel, 2.4 GHz & 5.8 GHz GHz 4xE1 SECTION 2: PRODUCT DESCRIPTION PAGE 2-11 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 2.3.2 Test Points / Power Indicator ON This is an LED indication. When lit GREEN, the LYNX.sc is powered. The LYNX.sc radio products do not have an on/off switch. GND RSL This is a test point referenced to chassis ground. This is used in conjunction with the next two test points to measure voltages related to radio performance. This is a test point which relates to the Received Signal Level (RSL). A voltage can be measured with a voltmeter (using the GND test point for reference) which corresponds to the actual power level of the incoming received signal. While the DISPLAY FAR END button is pressed, this RSL voltage corresponds to the RSL of the far-end radio. These measurements are used during installation, maintenance and troubleshooting. LOCAL TX PWR This is a test point which corresponds to the output transmit power of the radio. A voltage can be measured with a voltmeter (using the GND test point for reference) which corresponds to the actual power level of the outgoing signal. This measurement is used during installation, maintenance and troubleshooting

. This voltage only applies to the near-end and does not allow measurement of the far-end output transmit power, even when the DISPLAY FAR END button is pressed. There is a receptacle on the front panel to the right of the LOCAL TX PWR test point which is an installation adjustment allowing the output transmit power to be increased or decreased within the radio's specified limits. Using a small screwdriver, this adjustment is used to set the output power of the transmitter, in accordance to the path planning. The LYNX.sc systems requires professional installation. Transmitted output power limits may apply when using this radio. Consult FCC, IC, ETSI Western Multiplex or other regulatory authorities for limits which may apply. See Section 3.13.1 for details on setting output power. PAGE 2-12 SECTION 2: PRODUCT DESCRIPTION INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 2.3.3 Alarm and Status Indicators DATA LOSS BER When lit RED, this is an alarm condition indicating that the LYNX.sc radio is not receiving E1 input data on the corresponding data input channel. This alarm function can be disabled by rear panel DIP switch setting (see Section 2.4.4). Under data loss condition, the local transmitter injects AIS (Alarm Indication Signal). This is the Bit Error Rate (BER) alarm. When lit RED, this alarm condition indicates that the received signal bit error rate is above the error threshold of 1 x 10-6. This alarm condition typically indicates a path problem or a problem with the far-end radio and usually is not a problem with the near- end radio. RX SYNC When lit RED, this is an alarm condition indicating that the intended received signal is not being received. This alarm may the path, connections, or the near-end or far-end radio hardware. When the RX SYNC alarm is active, AIS (Alarm Indication Signal) is injected into the E1 line transmit output data port. indicate problems related to AIS OUT When lit RED, this is a status condition indicating that the radio receiver is transmitting AIS (Alarm Indication Signal) on the E1 line transmit output data port, due to loss of received signal. This typically indicates a path or connection problem or a near-end or far-end radio hardware problem. This alarm function can be disabled by rear panel DIP switch setting (see Section 3.12.5). FAN When lit RED, this is an alarm condition indicating a failure with one or both of the internal cooling fans. The radio is designed to operate within specification when only one fan is operating. The two fans are provided for redundancy only. RADIO FAIL When lit RED, this is an alarm condition indicating a major failure with the near-end radio hardware. It can also indicate improper connections to the CEPT-1 input port. FAR END When lit RED, this is an alarm condition indicating that there are alarm or status conditions present on the far-end radio. Press and hold the "Display Far End" button on the near-end radios to indicate the alarm conditions for the far-end radio terminal. Monitoring the far-end alarms can be helpful for radio installation and routine maintenance. SECTION 2: PRODUCT DESCRIPTION PAGE 2-13 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 2.3.4 Controls Loopback is a test method used which transmits either an internal or external E1 test signal and loops this E1 signal back at the far-end radio (re-transmits the signal back to the near end). The near end then receives the signal. This is very useful for testing because the test signal can be monitored at the near-end and the quality of the entire link can be measured using a Bit Error Rate (BER) test, or internal test features, without anyone going to the far-end radio location. When lit RED, this indicates that a bit error occurred while in loopback mode. If you are not using a BER test set, this LED may be observed to determine if there are any bit errors during loopback, for example during an overnight test. This is a push-button switch that executes the loopback mode for the corresponding channel. Loopback is initiated by pressing and holding this switch for approximately 3 seconds. Once in loopback mode, the LED which is embedded in the switch is illuminated YELLOW to indicate that Loopback is ON. The LED on the near-end radio flashes while the far-end is solid. Loopback is disabled by pushing and releasing the ENABLE button at either the near-end or far-end radio. Enabling loopback will interrupt traffic. This is an out-of-service test. This is a push-button switch provided only one the 4xE1 version that selects the channel for loopback mode. The channel is determined by the number of times the switch is pressed. Press (hold for 2 seconds and release) for channel 1, press again for channel 2, press again for channel 3 and press again for channel 4. Loopback is initiated using the ENABLE switch; the LED in the CH SEL button flashes in a group sequence to identify which channel is selected for loopback. This push-button provides the capability to determine alarms and status of the far-end radio. When pressed and held, the alarm and status LEDs and the RSL test point correspond to the far-end radios status and RSL value. This can be used for installation, maintenance and troubleshooting. When the LED on this switch is flashing, no far-end information is available. This typically indicates that there is no link between near-end and far-end radios. ERROR ENABLE CH SEL DISPLAY FAR END PAGE 2-14 SECTION 2: PRODUCT DESCRIPTION INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 2.3.5 Connections ORDERWIRE This connection is used to access the orderwire function. This is a facility for "telephone" style service from one radio to another. A standard electronic telephone [one with a handset and DTMF

(push-button tone) dialing] plugs into this connector. The user can dial the orderwire address of the far-end radio (or any radio in the LYNX.sc network) to establish telephone communication between sites. This communication does not interrupt or interfere with the other radio communications. The radio link must be operational to use this facility. The orderwire feature can be very useful for installation, maintenance and troubleshooting.

- Touch-tone Telephone* (for communication with far-end)

*Telephone connection specifications:

REN (Ringer Equivalency Number) DTMF tones Ringing Voltage

(Ringing voltage is adequate for modern solid state ringers, NOT for the older mechanical type ringers) 1.0 B within 1.5% of nominal freq. 48 VDC, typical SECTION 2: PRODUCT DESCRIPTION PAGE 2-15 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 2.4 Rear Panel Description The LYNX.sc radio rear panel, as shown in Figures 2-4 through 2-6, has connections and DIP switches that are used for installation, maintenance, operation and trouble-shooting. Prior to installation, you should familiarize yourself with the rear panel. Figure 2-4: Rear Panel, 1xE1 Figure 2-5: Rear Panel, 2xE1 Figure 2-6: Rear Panel, 4xE1 PAGE 2-16 SECTION 2: PRODUCT DESCRIPTION INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 2.4.1 RF Connection The RF port of the LYNX.sc radio is an N-type female connector that is an integral part of the filter assembly. The filter assembly occupies nearly the entire top half of the rear panel. The N-Type connector is used to connect the antenna, typically using coaxial transmission line. In some cases, waveguide may be used as the primary transmission line, in which case a waveguide-to-N adapter is required. For the LYNX.sc, 1/2" or 5/8 coaxial cable (LDF4-50 or LDF4.5-

50) is recommended. Coaxial cable that is 7/8 or larger can exhibit moding at 5.8 GHz and is not recommended for 5.8 GHz radios. For waveguide transmission line at 5.8 GHz, EW-52 waveguide is recommended. EW-63 will also work, but may exhibit more loss. SECTION 2: PRODUCT DESCRIPTION PAGE 2-17 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 2.4.2 DATA Connections The connection for the CEPT-1 (E1) interface is shown in Figure 2-7 as J1 through J4 (additionally J5 through J8 on the 4xE1 model). These connections carry the E1 signals in and out of the radio. Multiple capacity (2xE1 and 4xE1) provide extra sets of input and output ports to connect each E1 signal. The BNC data ports accept bipolar signals with the shield normally left open (floating) in order to eliminate ground loop problems. If desired, the BNC shield on the data ports may be grounded using switch settings on SW2. For balanced E1 input, use a 120 ohm balun and BNC cables to provide a RJ45 4-wire connection. SW2 has no effect when using the typical balun. Figure 2-7: CEPT-1 Interface Grounding Switch PAGE 2-18 SECTION 2: PRODUCT DESCRIPTION INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 2.4.3 Auxiliary Data Connections There are 5 auxiliary data connections for LYNX.sc as shown in Figure 2-4 through Figure 2-6. VF This connector is used to link two LYNX.sc radios at a repeater site for Orderwire operation. This would allow orderwire "telephone" calls to and from any point in the LYNX.sc network. The LYNX.sc orderwire circuit can also be connected to other existing orderwire networks. See Section 3.14.1 for details. ALARM This connector is used for monitoring alarms electrically. The alarm connections are essentially the same as described for the front panel, however instead of LED operation, alarm status is provided electrically by means of TTL and Form C relay connections. The TTL and Form C relays can be connected to other transmission equipment for monitoring alarm status locally or remotely. DIAG-

NOSTICS This is a serial interface port (RS-232 or RS-422, 9600 baud) to the LYNX.sc radio. This port provides maintenance information about the LYNX.sc radio(s) to a connected computer or terminal. This port is typically used for maintenance and troubleshooting or connection to network management systems. AUX DATA This is a serial interface port (RS-232 or RS-422, 9600 baud) which allows the user to connect auxiliary serial data from one point in the radio network to another. This facility can also be used for bridging the DIAGNOSTICS port for remote alarm and status monitoring (TBOS network management) or for connecting other equipment's serial alarm information. It can alternatively be used for separate data connection for LANs or other serial devices. PROTECT This is a port used to connect the LYNX.sc radio to an additional unit for Monitored Hot Standby (MHS) or Space Diversity (SD) configuration. The MHS and SD units can be configured to provide protection to the LYNX.sc radio by means of a "back-up"

radio which would switch-in should there be problems with the primary radio or the radio path. The protect feature is not available at the time of the printing of this manual SECTION 2: PRODUCT DESCRIPTION PAGE 2-19 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 2.4.4 Switches There are two sets of 8-segment DIP switches (SW1 & SW3) and two rotary switches (Address TENS and ONES), as shown in Figures 2-4 through 2-6 on the rear panel of the LYNX.sc radio. These switches provide user configuration of several radio parameters. A brief explanation for each function follows. Refer to the switch setting detail in Appendix B for your particular model. SW1 Input Alarm Disable These switch segments allow the user to turn off the DATA LOSS alarm for any input channel. This can be helpful if the data channel is not in use or while performing maintenance to temporarily turn off the alarm indication. Even when this alarm is disabled, the LYNX.sc radio will inject AIS into the transmitted data stream when there is a data loss condition. (see Section 3.12.4) Loopback Mode This switch segment allows the user to select either the internal or an external test signal while in loopback mode. (see Section 3.12.2) Error Unlatch AIS Disable Diag-

nostic Protocol Enable Aux Data This switch segment selects an optional mode for the ERROR LED to flash for each error occurrence (instead of latching on). This can be useful for short duration loopback testing when the operator is located at the terminal site and watching for errors. (see Section 3.13.3) This switch segment allows the user to select whether or not an AIS signal will be automatically injected into the received E1 data stream at BER 1 x 10-3. This can be useful for measuring threshold or when a E1 channel is not in use. The AIS will be injected into the received E1 data stream if the radio loses sync (RX SYNC alarm active), even if the AIS disable function has been selected. (see Section 3.12.5) This switch segment is default set to Telemetry Bit Oriented Serial (TBOS) mode on the diagnostics port. This is a non-proprietary network management protocol which is common to some radio networks. The other selection is for factory use only. (see Section 3.14.3) This switch segment allows the AUX DATA port to be optionally used as a clear service channel for RS-232 or RS-444 ( 9600 baud) user data. The radio normally bridges the AUX DATA port to the DIAGNOSTICS PORT for TBOS radio network management. (see Section 3.14.4) PAGE 2-20 SECTION 2: PRODUCT DESCRIPTION INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 SW2 Interface Connec-

tion These switch segments allow the user to have the shield of each CEPT-1 input connection either grounded or floating. The shield is normally floating to eliminate ground loop problems. (see Section 3.11) SW3 Spread-

ing Code This set of switch segments allow the user to select the spreading code for the spread spectrum signal. Both ends of a radio system must be set to the same code. Users may wish to change codes for radios that are nearby other similar radios to aid in interference rejection. (see Section 3.12.3) Channel Selection This set of switch segments programs the radio to match the specific RF channel corresponding to the RF filter set which has been installed. (see Section 3.12.1) Address There are two rotary switches which determine the radio's address (01 to 99). This address is used for Orderwire signaling and for the DIAGNOSTICS port TBOS address. (see Section 3.14.1) Refer to Appendix B for Switch Settings SECTION 2: PRODUCT DESCRIPTION PAGE 2-21 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Installation Accessories 2.5 The LYNX.sc radio is shipped with several accessories commonly required for the radio as described below:

AC Power Supply If ordered as an option, this power supply provides AC to DC conversion for use with AC powered locations. AC Power Cord This power cord connects the AC Power Supply, if ordered, to a standard 115V U.S. AC outlet. Rack Mount Brackets Two brackets (along with required mounting screws) are provided which allow 19-

inch rack mounting of the LYNX.sc radio. Terminal Connector D Connector 9-pin D Connector 25-pin RF Power Adjustment Cover This is a 6-pin mating connector used for DC power supply. Two of these mating connectors are provided. One is used for the DIAGNOSTICS port interface and another for the AUX DATA port. There are 2 mating connectors provided, one for the ALARM interface and the other for the VF interface. A small plastic cap is provided which is placed over the RF output power adjustment receptacle once output power has been set by professional installation personnel. Other accessories are available, such as orderwire handsets, connector adapters and special cables. These can be ordered separately upon request. PAGE 2-22 SECTION 2: PRODUCT DESCRIPTION INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Your Notes on the LYNX.sc Radio SECTION 2: PRODUCT DESCRIPTION PAGE 2-23 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3. Installation & Adjustments 3.1 Shipping Container The equipment is shipped in boxes unless ordered as an integrated system and configured at the factory, in which case the equipment may be racked and shipped in a crate. The equipment is packaged so as to prevent damage in transit. The boxes should be left intact and sheltered until arrival at the installation site. the shipping container shows signs of damage, If the transportation company should be notified immediately. Extra care and inspection of the contents is advised immediately upon receipt. It is recommended that all the packaging materials be retained. In the unlikely event that the equipment must be returned to the factory, use the original packing materials for return shipment. The original packaging materials are also recommended for transporting the equipment from location to location. Inside the primary shipping containers, internal boxes may contain other items. These boxes should also be saved for future use. Also, save the LYNX.sc radio test data sheet that is provided. The test data sheet can be placed where the LYNX.sc terminal will be installed for future quick reference. This sheet could also be placed in the front pocket of this manual, and the manual kept at the radio location for future reference. All LYNX.sc units are individually tested and the actual measured performance recorded on the Factory Test Data Sheet. You will find this information to be of use during installation, troubleshooting and maintenance. A set of quick installation instructions is also provided which can be useful for easy reference during installation. SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-1 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.2 Packing Items Identification The primary shipping container houses the radio and an additional box. The box contains several related items inside including:

v This manual v Installation accessory kit (see Section 2.5) PAGE 3-2 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.3 Before Installation Task List There are several tasks that should be accomplished prior to installing the LYNX.sc radio system. This section briefly describes the following:

- Site selection

- Line-of-Sight and Path Clearance determination

- Anticipated RSL calculation

- Fade margin calculation

- Availability calculation

- Frequency plan determination

- Power supply planning

- Antenna (and accessories) purchase Only directional antennas should be used with LYNX.sc spread spectrum radios. These can be grid or solid parabolic antennas

(minimum 2 foot - .6 meter). Flat panel antennas are also acceptable if the beam width is kept to a minimum. 3.3.1 Site Selection Requirements The radio site must have:

- access to the appropriate power

- close proximity to the telephone or computer system you wish to interconnect

- line-of-sight to the other radio location with adequate clearance

- location for mounting the antenna SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-3 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.3.2 Line-of-Sight and Path Clearance Guidelines The LYNX.sc radios will not operate properly unless they have line-of-sight between their corresponding antennas. The LYNX.sc radio transmission will not pass through trees or other obstacles. Factors to consider include:

- Earth curvature

- Future growth of trees

- Height of buildings In addition to the line-of-sight requirement, a well-engineered path will also have additional path clearance to allow for signal loss due to partial obstructions, atmospheric ducting and ground reflections. To maximize radio reception, 0.6 times the first Fresnel zone should be calculated and this distance added to the path clearance (in addition to trees or buildings). PAGE 3-4 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.3.3 RSL Calculation and Link Budget The received signal level (RSL) can be estimated using the following formula:

RSL (dBm) = Pout - FL1+ G1 + G2 - FL2 - Lp where: Pout is the transmitter output power (in dBm) FL1 is the feeder loss of the transmit side (in dB) G1 is the gain of the transmit antenna (in dB) G2 is the gain of the receive antenna (in dB) FL2 is the feeder loss of the receive side (in dB) Lp is the Path loss, defined by:

Lp (dB) = 96.6 + 20 log10F + 20 log10D where: F = Frequency in GHz (2.4 or 5.8) D = Distance of path in miles This link budget is very important for determining any potential problems during installation. If you have calculated the expected RSL, you can see if it has been achieved during installation, and troubleshoot if necessary. In the USA, 5.8 GHz models of the LYNX.sc may be installed with any size directional antennas and operated at full power. The 2.4 GHz model may require power reduction where: Pout -

FL1+ G1 is replaced by 30 - [(G1 - 6)/ 3] + FL1 In some countries effective isotropic radiated power (EIRP) limits apply, such as +6 dBW (+36 dBm) in Canada. Output power may need to be reduced, and the above path planning equation changed such that: EIRP (dBm) = Pout + G1 - FL1 SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-5 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.3.4 Fade Margin Calculation The fade margin is the difference between the actual received signal and the radios threshold. Using the formula provided in Section 3.3.3, the anticipated RSL can be calculated. Compare this RSL to the specified threshold of the LYNX.sc radio, which is shown in Section 2.2, and calculate the fade margin as the difference between the two signal levels. Dispersive fade margin is another factor that many microwave path engineers may use to plan their link budget. For the LYNX.sc radio, the dispersive fade margin is in excess of 55 dB and therefore is not a determining factor in path planning. This excellent dispersive fade margin performance is important because the spread spectrum RF signal has considerably wide bandwidth. PAGE 3-6 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.3.5 Availability Calculation Availability of the microwave path is a measure of the percent of the time that the link will operate without producing an excessive BER due to multipath fading. In the absence of direct interference, availability is affected by the following:

- Path length

- Fade margin

- Frequency (2.4 GHz or 5.8 GHz in the case of the LYNX.sc radios)

- Terrain (smooth, average, mountainous)

- Climate (dry, temperate, hot/humid) Depending on the type of traffic carried over the link, the system designer may wish to design for a specific availability. For example, if the data or voice traffic that is carried by the radio is critical then it may be designed for a very high availability (e.g. 99.999% or 5.3 minutes of outage per year). To improve availability, for example, the fade margin can be increased by making the path shorter, or by using higher gain antennas in conjunction with lower loss feeders (by using high quality transmission line or shortening feed length). SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-7 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.3.6 Frequency Plan Determination When configuring radios in a hub or repeater configuration, careful engineering of the LYNX.sc radio frequency plans and antenna locations should be performed in order to minimize potential interference between the nearby radios. As a rule of thumb, do not place identical frequency plan radios (e.g. two A channel radios) at the same site. In most cases, it is desirable to use a different frequency plan (e.g. A versus B). However, with careful engineering, placing more than one radio of the same frequency channel plan at the same site can be accomplished. In fact, the LYNX.sc frequency plan is designed to allow complex hub configurations that may require re-using the same frequency plan. When designing these types of configurations, antenna size and antenna location are critical. If identical channel plans must be used at the same site, the same radio channel (e.g. A1 and A1) should be used at a site to minimize interference. Using alternate channels (e.g. A1 and A2) is less likely to be successful (and therefore not recommended) due to the high level of transmitter to receiver isolation required from the antenna system. Sometimes it is required to locate the LYNX.sc radio nearby a transmitter that is the same as, or close to the LYNX.sc receive or transmit frequencies. In this case, the LYNX.sc terminal that should be placed closest to this interfering transmitter should be the specific terminal with the receive frequency which is furthest from this unwanted transmitted frequency. This approach minimizes the potential of interference. While interference conditions are rare when using the LYNX.sc radios, cases of interference may be overcome by exchanging the radios from end to end or simply reinstalling the filter unit, as described in Section 4.2 (thus swapping the frequencies of both ends of the radio link). In some cases, changing frequency plans (e.g. from A to B) can also help mitigate any interference. Section 4.8 of countermeasures in further detail. this manual describes interference PAGE 3-8 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.3.7 Power Supply Planning The LYNX.sc radio must have access to a supply of appropriate power, either DC or AC (if the AC adapter option has been ordered). The LYNX.sc can be powered from a DC battery system, or from a solar or generator power plant, usually with battery reserves. Typically either a positive or negative ground 24 or 48 volt supply is used. For DC, be sure the cable is of sufficient gauge to carry the necessary current and it is less than three (3) meters (9.75 feet) in length. Before installing the radio, plan for the continuous power consumption needs in accordance with the specifications given in Section 2.2 of this manual. It is also wise to plan for backup power for critical communication circuits (including the LYNX.sc radio). Backup power allows the radios and associated equipment to continue operation when primary power is interrupted. SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-9 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.3.8 Antenna Planning Using the path planning tools, proper antenna size can be determined which will yield the desired path performance. In general, the larger the antenna that is used with the LYNX.sc radio, the better the link will perform. Larger antennas have narrower beamwidth and higher gain, which will yield better link performance (higher fade margin, better availability) and improve immunity to interference

(due to the smaller beamwidths). However, larger antennas are more costly to purchase and install than smaller antennas, in some cases requiring special equipment for installation. All of these factors should be taken into consideration when selecting antennas. In areas where transmitted output power restrictions apply, the use of larger antennas will maintain the benefit of narrow beamwidths and receive gain. However, output power may need to be reduced to meet regulations. (See Section 3.13.1) Prior to installation, the specific antenna location and mounting should be determined. This advanced planning also yields the transmission line requirements. Only directional antennas should be used with LYNX.sc spread spectrum radios. These can be grid or solid parabolic antennas

(minimum 2 foot - .6 meter). Flat panel antennas are also acceptable if the beam width is kept to a minimum. PAGE 3-10 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.4 Tools Required The following tools may be required for the installation of the LYNX.sc radios:

- Phillips (cross tip) screwdrivers (for 19-inch rack mounting and attachment of brackets)

- Small blade standard screwdriver (for power supply connector and RF output power adjust)

- Soldering iron (if using any D-type connectors)

- Wire strippers (for removing insulation from power supply and other wiring)

- Digital Voltmeter (to measure RSL, Tx output power, Alarms) The following tools are recommended for the installation of the LYNX.sc radios:

- RF power meter (to measure transmitter output power)

- Cellular phone or two-way radio (for talking with far-end crew and tower crew)

- Bit Error Rate test set (to test link after installation)

- Touch-tone Telephone* (to test orderwire circuits and for communication with far-end) Additional tools will likely be needed for antenna and transmission line installation and antenna alignment. Consult Sections 3.8 through 3.10 of this manual for more details.

*Telephone connection specifications:

REN (Ringer Equivalency Number) DTMF tones Ringing Voltage

(Ringing voltage is adequate for modern solid state ringers, NOT for the older mechanical type ringers) 1.0 B within 1.5% of nominal freq. 48 VDC, typical SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-11 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.5 Frequency Channel Plans The LYNX.sc system offers several non-overlapping channel plans for the different models of radio. This channel plan arrangement allows users to implement LYNX.sc systems in the proximity of other LYNX.sc radios (planned or unplanned), hub and repeater applications, and can be used to mitigate interference. The channel plans are illustrated below in Figures 3-1 through 3-6. Section 4.2 and 4.3 describe how to change frequency channel assignments of a LYNX.sc radio. Figure 3-1: Channel Plan, 2.4 GHz 1xE1 Figure 3-2: Custom Channel Plan, 2.4 GHz E1 PAGE 3-12 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Figure 3-3: Channel Plan, 2.4 GHz 2xE1 Figure 3-4: Channel Plan, 5.8 GHz 1xE1 SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-13 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Figure 3-5: Channel Plan, 5.8 GHz 2xE1 Figure 3-6: Channel Plan, 5.8 GHz 4xE1 PAGE 3-14 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.6 Mounting the LYNX.sc The LYNX.sc radio can be mounted at any height in a standard 19-inch rack. Blank rack-mounting spaces above and below the LYNX.sc are recommended, especially if the surrounding equipment dissipates a considerable amount of heat (over 50W). The LYNX.sc radio may be set up for mounting with the front edge projecting from the front face of a standard 19-inch rack using the rack mounting brackets enclosed with the screws in the Accessory Kit (4 per bracket). The rack mounting brackets may be reversed, in order to install for flush or cabinet mounting if preferred. Depending on rack configuration, it may be necessary to remove the four adhesive backed rubber feet on the bottom of the unit. The LYNX.sc radio has internal fans which intake and exhaust on the left and right sides of the chassis. When rack mounting, it is important to leave a small gap between the outer edges of the radio and the inside edge of the rack. The LYNX.sc radio may alternatively be placed on a table or shelf attached to a wall. Because of the low weight of the LYNX.sc, any mounting option other than rack mounting will be less secure. SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-15 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.7 Power Connection and Wiring There is no ON/OFF switch on the LYNX.sc. As soon as power is applied, the equipment will be operational. This means that there can be up to 1W of RF power present at the antenna port. The antenna port should be terminated before power is applied. Power is connected using the DC power plug contained in the Accessory Kit. Use Table 3-A or 3-B along with the associated diagram of Figure 3-7 or 3-8 to connect the DC power cables. For example, for a negative DC power input, use Table 3-A and Figure 3-7. NEGATIVE DC POWER INPUT

(20 TO 63 VDC) PIN 1 2 3 4 5 6 FUNCTION Power (DC) Ground (see figure 3-7) Return (+DC) Return (+DC) Ground (see figure 3-7) Power (DC) Table 3-A: DC Power Connection for Negative Supply POSITIVE DC POWER INPUT

(+20 TO +63 VDC) PIN 1 2 3 4 5 6 FUNCTION Return (DC) Ground (see figure 3-8) Power (+DC) Power (+DC) Ground (see figure 3-8) Return (DC) Table 3-B: DC Power Connection for Negative Supply Pins 1 and 6 are connected together on the motherboard. Either pin may be used to apply (-DC) DC power input. Similarly, pins 3 and 4 are connected together on the motherboard and may be used to apply (+DC) DC power input. For DC power return connection, connect to the opposite voltage

(either the -DC or the +DC Pin) and connect the return to ground at the DC power plug on pins 2 and/or 5. PAGE 3-16 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.7.1 DC Power Wiring Connect the power cable with adequate current rating (minimum of 20 AWG) to the terminals shown on the removed (not plugged into the radio) DC power plug using the screw connections. The recommended minimum current rating of external fuses and cables is 3 Amps. The LYNX.sc radios consume less than 1 Amp at 48V and less than 2 Amps at 24V. Be sure the DC power cable is less than 3 meters (9.75 feet) in length. Each LYNX.sc terminal should be externally fused separately with a 5 Amp maximum fuse. The DC power cable must be less than three (3) meters in length. If using negative power, connect the negative voltage to pins 1 or 6. Connect the ground return connection to pins 3 or 4. See Figure 3-7. If using positive power, connect the positive voltage to pins 3 or 4. Connect the ground return connection to pins 1 or 6. See Figure 3-8. The ground connection is available at pins 2 and 5. Either pin may be used to ground the return side of the power supply. Do not ground both sides of the power supply. Proper grounding, either through the chassis and/or the power supply, can be very important for protection from lightning. A grounding screw hole is provided on the rear panel. The ground connection may be left floating if the power supply is referenced to ground externally and to avoid ground loops in some configurations. However, this may not provide adequate grounding for lightning protection. Use a DVM (digital voltmeter) to verify voltage and polarity on the DC power plug. Do not connect the DC power plug to the rear of the LYNX.sc terminal until a load is connected to the antenna port (either an RF pad, or an RF cable and antenna). SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-17 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Figure 3-7: Negative Voltage DC Connection Figure 3-8: Positive Voltage DC Connection Make sure that when connecting the mating plug that it is properly oriented (terminal screws pointing up) and securely fastened. PAGE 3-18 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.7.2 AC Power Connection The optional AC power supply operates from any AC voltage 100V - 250V and 50 Hz or 60 Hz. The AC supply is equipped with a mating connector that plugs directly into the LYNX.sc radio and an AC cord with a 3-pin AC plug. The AC cord color code is shown in Figure 3-9 in case users wish to replace the AC plug supplied with a different type of plug. Figure 3-9: AC Connection SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-19 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.8 Antenna Connection The LYNX.sc radio is equipped with an N-type female connector at the antenna port located on the rear panel. A short length (~6 feet) jumper cable such as RG-214 coax (or pigtail) fitted with two N-

type male connectors can be used to connect the antenna port to the antenna transmission line

(see Section 3.9). The recommended cable type for a jumper is RG-214. A low loss 50-ohm cable (for example LDF4-50 1/2 inch coax) or EW-52 waveguide (for 5.8 GHz radios) is recommended for the antenna transmission line between the top of the rack and the antenna. The return loss presented by the transmission line at the top of the rack should be as high as possible (20 dB, minimum recommended). The length of the antenna transmission line should be kept as short as possible (to minimize losses). For 5.8 GHz radios, to minimize feeder losses, the use of 5.8 GHz elliptical waveguide is recommended (typical loss is 1.25 dB/100 ft) for feeder lengths in excess of 200 feet. Depending on path length and feeder length, 1/2 inch coax cable can be used with 5.8 GHz radios. For the LYNX.sc radio, 1/2 or 5/8 coaxial cable (LDF4-50 or LDF4.5-50) is recommended. Coaxial cable 7/8 or larger can exhibit moding at 5.8 GHz and is not recommended for 5.8 GHz radios. For waveguide transmission line at 5.8 GHz, EW-52 waveguide is recommended. EW-63 will also work, but may exhibit more loss. Do not use right angle N-type connectors with the 5.8 GHz LYNX.sc radios: they may present high loss at 5.8 GHz. Do not use a low quality N-type jumper cable with the LYNX.sc. Some cable types, such as RG-8, may have high loss at 5.8 GHz. PAGE 3-20 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.9 Transmission Line Connection The transmission line feeder (such as LDF4-50 1/2 inch coax cable or EW-52 elliptical waveguide) should be prepared first by cutting to the approximate length (allowing some excess) and installing the appropriate connector on the antenna end. The prepared transmission line is then pulled through the cable ducts, trays or conduit (as required) to the antenna, while being careful not to kink or damage the transmission line in any way. The transmission line should be supported in a tray on horizontal runs and by hangers on vertical runs. Hangers should be spaced according to the manufacturers instructions (typically every 5 feet under conditions of no ice and not greater than 85 mph winds). The transmission line should be grounded using the manufactures recommended grounding kit. Grounding kits attach to the outer copper conductor. Grounds must be installed at the antenna, at the bottom of the tower (if applicable) and where the transmission line enters the building. Long transmission line runs should be grounded every 100 feet. In areas of high incidence of lightning, dissipaters should be attached to antennas. In addition, coaxial, in-line, spark-gap type, lightning suppressors should be added at the building/enclosure. the coax cable before entering the bottom of Any in-line lightning protection device must be rated for the operating frequency of the LYNX.sc (2.4 or 5.8 GHz). After installation, the transmission line is terminated with an N-type male connector/adapter attached at the equipment end. For waveguide, this typically requires a CPR-to-N adapter. Prior to operation, the electrical integrity of the transmission line, including all connectors, can be checked with a simple DC check between the center conductor and outer conductor. (This is neither possible, nor required for waveguide). The transmission line should ideally be connected directly to the antenna at one end and to the LYNX.sc antenna port at the other end. However, short RG-214 type pigtail jumper cables may be required to avoid sharp bends in the transmission line to limit stress on either connection. 7/8 inch coax cable or larger is not recommended for use at 5.8 GHz and higher frequencies. Do not use right angle N-type connectors with the 5.8 GHz LYNX.sc radios: they may present high loss at 5.8 GHz. Do not use a low quality N-type jumper cable with the LYNX.sc. Some cable types, such as RG-8, may have too high a loss at 5.8 GHz. SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-21 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.10 Antenna Installation & Alignment Due to the possibility of exposure to RF radiation above the recommended levels, do not stand within five (5) meters of the antenna for prolonged periods during system operation. It is the responsibility of the installer to insure that the antenna is mounted in a place that is not accessible to the public. The antenna installation consists of mounting the antenna on the tower, building roof, or other location that provides line-of-sight path clearance to the far-end location. In general, antennas smaller than 2 feet diameter are not recommended for urban areas due to their wider beamwidths, which results in higher interference susceptibility. For 2.4 GHz LYNX.sc radios, a minimum of 4 foot

(1.2m) diameter antennas, or larger, are recommended. Antennas should be ordered with a suitable mounting kit specific to the site requirements. For example, specifying round or angle tower leg adapters, or a roof tripod as necessary. If the antenna is to be mounted indoors, "looking" through a window, it is recommended that the antenna be placed approximately 12 inches away from the glass and within 10 degrees of a right angle to the glass. The glass should be lead-free or very low-lead content type and avoid any metallic glass coatings for best results. The antenna must be very rigidly mounted, with adequate room for azimuth and elevation adjustment. The antenna polarization must be the same at both ends of the link, either vertical or horizontal. In general, antenna mountings require a support pipe to which upper and lower support brackets are attached with U bolts. The antenna and optional elevation and azimuth adjustment rods are then mounted onto the support brackets. The whole structure must be adequately grounded for lightning protection. The antenna system must always be installed according to the manufacturers instructions. Unless special test equipment is available, two operating LYNX.sc terminals are required to align the antennas. Alternatively, a CW generator may be used to transmit a signal toward the end under alignment. The antenna is coarse aligned using visual sighting and then fine aligned using the receive signal level (RSL) voltage of the LYNX.sc. The RSL voltage reading can still be used to peak antennas even if the radios have not synchronized, however far-end RSL cannot be measured from the near-end terminal until radios are synchronized. PAGE 3-22 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 To coarse align the antenna, first set it for flat elevation (no up or down tilt) using a spirit level. Then point it at a heading marker obtained using a compass back-bearing from an adjacent location,

(ideally, 100 feet or more away from the antenna). If a heading marker cannot be set sufficiently far away (for example when on a city building roof or looking through a window) then a rough azimuth setting can be obtained by sighting along the antenna feed. It should be verified that both antennas are on the same polarization by using the manufacturers instructions. Otherwise the RSL will be approximately 25 to 30 dB below the calculated level. Most antennas will also need fine alignment obtained using an operating link because it is very important to maximize the receive RF signal level at each end of the radio link. Read Section 3.7 before applying DC power to the LYNX.sc radio. Once the coarse alignment has been set-up at both ends, then the link can be powered and some level of reliable communication established. The voltage at the LYNX.sc front panel RSL test point should be measured with a DVM to determine the relative receive RF signal level. For the fine alignment, adjusting first the azimuth and then the elevation of the local antenna will maximize the RSL voltage. Then, the far antenna is aligned in the same way, using the RSL voltage of its local LYNX.sc radio. When aligning antennas it may be convenient to run two wires from the RSL and ground test points to the antenna so that the voltmeter reading is directly visible to the technicians aligning the antenna. Also, a cellular telephone or two-way radio may be useful for coordinating alignment activities between both ends of the link. Once the radios are coarse aligned and synchronized, the built-in orderwire phone service can also be used to coordinate alignment between both ends of the link. An orderwire telephone will provide end-to-end voice communications once radios are synchronized. Synchronization usually can be accomplished by coarse alignment only. After synchronization, the orderwire phones can be used to communicate between radio sites for antenna fine alignment. The phone interconnect cable can be extended to the antenna when desired. The larger the antenna size, the more critical alignment becomes: for example, with a 2 foot dish, the antenna can be moved 3 degrees off the correct heading before the receive signal level drops by 3 dB. This compares with a 6-foot dish which may only be moved 1 degree for the same degradation. The graph shown in Figure 3-10 shows the typical variation of RSL voltage as the receive signal level is increased from threshold to a higher level. There is some variation between LYNX.sc receivers, but an approximate estimate of the potential RSL value may be made using this figure. SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-23 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Use the Factory Test Data Sheet shipped with your LYNX.sc terminal to obtain the best estimate of your RSL. Above 0 dBm RSL, the receiver may produce errors: however this level is rarely likely to be exceeded. A link budget calculation should be made to calculate the anticipated RSL as described in Section 3.3.3. During anomalous propagation conditions, the RSL may fade but will not increase up more than 10 dB (except in unusual very long paths which may fade up by 15 dB). Antenna alignment should enable the RSL to be peaked to the level calculated in the link budget. If the RSL is peaked but is approximately 20 dB below the calculated level, then it is likely that the antennas are aligned on a sidelobe of the antenna's radiated signal. In this case, the antennas should be rotated in a wide arc until the main lobe is located. (Other possible causes of low RSL are path obstructions, loss in connectors, adapters and pigtail jumper cables or different antenna polarization at each end of the link.) Figure 3-10: Typical RSL Voltage versus Received Signal Level (RSL) PAGE 3-24 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.11 CEPT-1 (E1) InterfaceConnection The CEPT-1 interface connection to the LYNX.sc radio is on the rear panel. Additional external lightning protection devices are recommended for the CEPT-1 connections if the radio is installed in an area prone to lightning. The CEPT-1 connection to the LYNX.sc is at the data interface on the rear of the shelf. Individual BNC connectors are used to interface the line transmit and receive functions. Seventy-five (75) ohm co-axial cables with BNC fittings should be used to connect LYNX.sc to external equipment. If a balanced 120 ohm connection (RJ45) is required, an optional balun will provide this interface. If you can not locate these baluns (balanced/unbalanced) devices, please consult the factory. The DATA OUT port provides a bipolar signal (positive and negative pulses) referenced to ground, with the BNC shield connected to ground. However, the DATA IN port accepts a similar bipolar signal with the BNC shield normally left OPEN

(floating) in order to eliminate any ground loop problems. If desired, the BNC shield on the DATA IN port may be grounded using the selector switch SW2. Position Description 1 2 3 4 Grounding Condition Channel 1 Grounding Condition Channel 2*

Setting 0 = Floating 1 = Grounded 0 = Floating 1 = Grounded 0 = Floating 1 = Grounded 0 = Floating 1 = Grounded

* Where applicable Figure 3-11: CEPT-1 Interface Grounding Switch Grounding Condition Channel 3*

Grounding Condition Channel 4*

SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-25 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.12 DIP Switch Settings A quick reference guide to all DIP switches is provided in Appendix B. DIP switch settings are noted by their position, either up (1), or down (0), not by on/off as may be printed on the DIP switch assembly. 3.12.1 Channel Selection The LYNX.sc radio offers several frequencies of operation except for the 2.4 GHz 2xT1 and the 5.8 GHz 4xT1 models (see Section 3.5).There are DIP switch segments (typical numbers 5 through 8 on SW3) which define the frequency channel plan of the LYNX.sc radio (refer to Appendix B). The DIP switches must be set to match the filter assembly that is mounted on the radio. For single and double capacity models, positions 5,6 and 7 define the frequency channel plan of the radio (e.g. A, B, C), the last DIP switch defines the transmit channel of the radio (e.g. A1 or A2). Radios are shipped from the factory with their DIP switch segments set to match the installed filter. In most cases, no modification of these switches is required.` Also, there are labels on the RF filter illustrating the correct DIP switch settings. One label is right side up and the other is upside down. Set the DIP switch settings for the label that is right side up. If a new filter is installed, or the existing filter is rotated for opposite channel configuration (e.g. A1 to A2), reset the DIP switches to match the right side up label on the filter. Refer to Section 4.2 for more information. The radio channel selection is user adjustable by removing and replacing, or reversing the filter assembly. This allows units of the same radio model to be used as spares for several channels. For example, if a network of LYNX.sc radios has several radios using all three E1 channel plans at 5.8 GHz, a single spare unit of any channel plan can be used to spare all the radios. If a radio failure were to occur in the network, the filter assembly of the failed unit would be removed and replace the filter assembly in the spare radio. The DIP switch segments on the spare may need to change to match the installed filter and the spare radio could be put into service. The DIP switch setting must match the filter assembly mounted on the radio. Also, both radios of a link must have opposite channel plans (e.g. A1 and A2). Consult Section 4.2 of this manual for more information on changing RF channels. Consult Appendix B for proper frequency channel switch settings. Other NON-standard frequency plans may be offered in the future. In these cases, follow the DIP switch setting on the filter label. PAGE 3-26 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.12.2 Loopback Test Signal Selection The LYNX.sc radio allows loopback operation using an internally generated test signal or using an externally generated test signal. A single DIP switch segment on SW1 as shown in Figure 3-12, allows the operator to select the use of either the internal or an external test signal. The factory setting for loopback mode is internal. Figure 3-12: Loopback Mode Selection SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-27 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.12.3 Spreading Code Selection The spreading code is the pseudo-random chip sequence that is mixed with the data to produce the spread spectrum signal. The spreading code is generated by the LYNX.sc radio internally. Different codes can be selected using the DIP switches on the LYNX.sc radio rear panel. The spreading code must be the same for both ends of a radio link. The spreading code has no effect with the Model 31850 (4xE1) 3-

channel LYNX.sc. Spreading codes are all set in the factory to code 1. Should the code need to be changed, then both ends of the link must be changed. Changing the spreading code is an out-of-service adjustment. There are two DIP switch segments on SW3 located on the rear panel which select the spreading codes. See Figure 3-13 for DIP switch segment settings. Figure 3-13: Spreading Code Selection PAGE 3-28 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.12.4 Input Alarm (Data Loss) Enable/Disable The LYNX.sc radio provides a capability to enable or disable input alarms (Data Loss). On the front panel and over the alarm and diagnostic interfaces, an alarm condition is normally generated if there is no input data signal (E1) to the radio. For example, in the case of the double E1 capacity model, the radio may have been installed in a location only requiring one E1 signal for traffic while the second E1 channel has been left idle (for future planned expansion). In this case, it may be desirable to disable the input alarm to the second channel so that local and remote alarms are not regularly generated by the (known) lack of this data input. When the network is later expanded to include traffic on the second E1, this switch can be set to enable the input data alarm condition. See Figure 3-14 for DIP switch segment settings for the 4xE1 model. Refer to appendix B for all models. When a DATA LOSS alarm condition occurs, the LYNX.sc radio will inject AIS into the incoming data stream, even if the input alarm has been disabled. 1xE1 and 2xE1 Models:

On SW1, switch segment(s) 1 (and 2) apply to channels 1 and 2 respectively. 4xE1 Model:

On SW3, switch segment 3 applies to Channel 3 input while switch segment 4 applies to Channel 4 input. Figure 3-14: Input Alarm Disable Switch SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-29 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.12.5 AIS Enable/Disable AIS (Alarm Indication Signal) is the blue code (all 1s) that keeps the digital line interface active under data loss conditions. AIS is required by certain equipment to maintain synchronization (for example, it is required on all leased line circuits). However, it is not required by all equipment (for example, a CSU/DSU will initiate its own blue code to the line under data loss conditions). Under test conditions, when measuring receive threshold, for example, it may be necessary, to disable AIS to facilitate BER measurement. There is a user selectable DIP switch segment on the rear panel of the LYNX.sc radio that includes selection of the AIS function (on/off) at the receiver line output. When the AIS is selected (on), the CEPT-1 signal will send blue code to the line when the received BER exceeds 1 x 10-3. This function is similar to a data mute function. When the AIS is disabled (off), no insertion of data will take place unless an RX SYNC alarm condition occurs. Refer to Figure 3-15 for DIP switch segment information. The standard factory setting is to have the demodulator AIS alarm selected ON because it prevents a severely errored signal (possibly unsynchronized) from being sent out to the line. It is recommended that AIS be selected ON for normal operation. It is recommended that AIS be selected OFF for measuring BER at threshold. This DIP switch does not affect AIS injection into the transmitted data stream upon a DATA LOSS condition. Figure 3-15: AIS Switch PAGE 3-30 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.13 System Turn-up to Service 1. Prior to installing the system, it may be desirable to perform a back-to-back test of the LYNX.sc radio pair. Consult Section 4.9 for further details. Back-to-back testing is a simple way to verify that the LYNX.sc radios are fully operational before they are installed. Installation adds several variables (such as antenna alignment) which can lead to system turn-up delays. Also, during back-to-back testing, the DIP switch settings and some connections can be tested. This step can eliminate a majority of troubleshooting once the radios are installed. for temporary near-end and A cellular phone or two-way radio system (walkie talkie, CB, mobile radio) can be very useful during installation. These can be used far-end communications between the installation personnel at one site and installation personnel at the other site while installing the system. These can also be helpful for communication between a person at the top of a very tall tower and ground personnel. The LYNX.sc radio incorporates an internal Orderwire feature that provides end-to-end telephone style communications. However, the link must be partially operational to use this feature. In lieu of, or in addition to the use of cellular phones or two-way radio, this Orderwire feature can also be very useful for installation, but typically cannot be put into service until step 8 or 9 of this procedure is completed. See Section 3.14.1 for more details. 2. 3. 4. 5. 6. Perform a general alignment of the antennas on both ends of the path using binoculars, compass or other related tools. It is important to have the antennas aligned as accurately as possible before putting radio traffic over the link. This will help in getting the system running more rapidly. See Section 3.10 for more details. Connect the transmission line to the antenna, and feed it to the LYNX.sc radio location

(see Section 3.9). Connect the opposite end of the transmission line to the N-type female connector located on the filter assembly which occupies the top half of the LYNX.sc rear panel. The connection must be terminated into an antenna or a load before DC power is applied to the radio. Verify that DIP switch settings for frequency channel selection match that of the filter that is installed on the rear of the radio. Consult 3.12.1 for further details. The far-end radio must have the same channel plan (e.g. A, B, C) as the near-end radio, and the opposite Tx and Rx frequencies (e.g. A1 and A2 make up a matched pair of radios). Verify that the DIP switch settings for spreading code are the same for both ends of the radio link (see Section 3.12.3). With the DC power source active, but not plugged into the LYNX.sc radio, using a voltmeter, confirm that the DC mating connector has the proper power connections in SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-31 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 accordance with Section 3.7. Verify the polarity and the absolute voltage on all pins. Verify ground connection for power. 7. Connect power to the LYNX.sc radio. Verify that the Front Panel ON LED indication is illuminated. This confirms that power has been properly applied. that the RF Antenna port connection Ensure is properly terminated before applying power to the LYNX.sc terminal, as in step 3. When the LYNX.sc radio is initially powered-on, some alarm conditions may be present. This is normal and alarms can be ignored at this time. 8. Place a voltmeter across the GND and PWR front panel test points. See Figure 3-16 and 3-

17 for voltage setting information and Table 3-C for typical output power levels for given cable lengths where EIRP limits apply. If necessary, use a small screwdriver at the front panel receptacle to adjust the output power of the local transmitter in accordance with the path analysis calculations. The recessed potentiometer is rotated clockwise to increase transmit output power and counter clockwise to decrease transmit output power. After verifying correct setting of the transmit output power, disconnect the voltmeter. Place the cover cap found in the installation accessory kit over the front panel receptacle. The LYNX.sc radio requires professional installation. With some LYNX.sc models, in certain countries, there may be Effective Isotropic Radiated Power (EIRP) the maximum output power that the LYNX.sc radio can transmit given the transmission line loss and the gain of the antenna. Consult with appropriate government agencies or Western Multiplex if there is any question regarding maximum output power allowed. limits which dictate In the USA, 5.8 GHz models may be operated at full power. 2.4 GHz models may require a power reduction of 1 dB from +30 dBm input power, as measured at the antenna feed, for every 3 dB that the antenna gain exceeds +6 dB. See Section 3.3.3 and Tables 3-

C or 3-D for more details. PAGE 3-32 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Figure 3-16: Typical RF Output Power versus PWR Voltage, 2.4 GHz Models Use the LYNX.sc Factory Test Data sheet to determine more precisely the voltage corresponding to the RF output power. SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-33 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Figure 3-17: Typical RF Output Power versus PWR Voltage, 5.8 GHz Models Use the LYNX.sc Factory Test Data sheet to determine more precisely the voltage corresponding to the RF output power. PAGE 3-34 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 For precision measurement of transmit output power, it is best to connect an RF power meter to the antenna port. The PWR port voltage may not provide enough precision. This is especially important where EIRP limits apply to the installation. In cases of no EIRP limits, the radio transmitter output power can be adjusted to maximum for installation, except for very short paths using very high gain antennas, where excessive power may not be advised. Dont forget that the RF output port should be terminated at all times when power is applied to the LYNX.sc radio. Therefore, disconnect power to the radio before connecting a power meter and reapply power once connected. Often, an RF power meter may have a limit to the input power that it can measure without damage. It is advised to place a calibrated fixed value RF attenuator (typically 20 dB or more) between the LYNX.sc radio and the power meter to assure proper operation and safety for the RF power meter. The value of this fixed attenuation can then be added to the value of the RF power meter reading to obtain the actual LYNX.sc radio transmitter output power. 9. Connect a voltmeter across the GND and RSL front panel test points. This voltage reading corresponds to the Received Signal Level (RSL) of the near-end radio. In other words, RSL is the amount of signal the near-end radio is receiving from the far-end radio. Since the antennas have not been finely aligned, it is not expected at this time that the RSL will read very high. However, at this point it can be verified that some communication is taking place between the two LYNX.sc terminals. Use the RSL voltage reading to align the antennas. Align one antenna at a time in accordance with Section 3.10. Complete alignment of both ends of the radio link before going further. The RSL voltage output on the radio's front panel will output a voltage range over full receiving capability of the radio

(approximately 10 VDC at 0 dBm to 0.0 VDC at threshold). the The LYNX.sc radio has a unique feature of allowing measurement of the far-end RSL from the near-

end radio. This is only possible if the LYNX.sc radios are communicating (the RSL is above threshold). The far-end RSL can be used to verify that adjustments to local antenna alignment are corresponding to the far-end radio reception. Far-end RSL is measured by pressing and holding the DISPLAY FAR END front panel button. While this button is held, the RSL voltage indicates the RSL of the far-end radio. RSL of both ends should be verified to be within approximately 2 dB of predicted value (see Section 3.3.3). There are several factors that can contribute to low RSL:

- Incorrect antenna alignment (aligned on a lobe and not on the main signal)

- Improper polarization alignment of antennas (horizontal vs. vertical)

- Transmission line problems (loose connections, bent or damaged cables, lossy adapters)

- Path obstructions (trees, buildings, hills, etc.)

- Path clearance (line-of-sight, earth curvature, Fresnel zone, diffraction and partial SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-35 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 obstruction)

- Weather (inversion layers, ducting and multipath)

- Antenna feed (coaxial/connector) problem The LYNX.sc radio requires professional installation. Dont forget that the transmitter output power adjustment on the LYNX.sc radio effects the RSL. Depending on EIRP limits (if any), path distance, and antenna gain, you may need to adjust the output transmit power to the proper level before putting the radios in service. If radio synchronization has been established, the radio link may be able to provide some limited communications over the link. It can be helpful to establish voice communications from one end of the radio link to the other using the Orderwire feature of the LYNX.sc radio. See Section 3.14.1 for details. If RSL is lower than anticipated, recheck the path clearance and transmission line as these are the typical causes of low RSL. Radio operations can be verified by connecting radios back-to-back with attenuators (40-60 dB), (see Section 4.9). If the problem remains, consult Section 4 of this manual for troubleshooting techniques which will help determine the source of the problem. 10. 11. Once RSL is verified to be near the predicted value, the radio link is ready for data. You may verify error-free operation by using the loopback function, as described in Section 3.13.2 or BER testing, as described in Section 4.10. If the link is not error-free, see Section 4.7 for troubleshooting guidelines. Once radio performance is verified and acceptable, with loopback mode turned off (press the ENABLE button, the LED will turn off), the LYNX.sc radios can now be put into service with the intended E1 traffic. Connect the E1 signal to the CEPT-1 Interface BNC connector. Refer to Section 3.11 for configurations of these connections. With E1 traffic applied in both directions, all front panel LEDs, except for POWER and any unused E1 ports, will be off. If LEDs are lit, consult Section 4 of this manual. 12. Now that the link is operational, other services can be connected including Orderwire, Diagnostics, Alarms and Aux Data (Service Channel). Consult Section 3.14 for details on these connections. PAGE 3-36 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 TRANSMITTER POWER (dBm)

. . Feeder Feeder Length Length 4' Dish 6' Dish 8' Dish 4' Dish 6' Dish 8' Dish 2' Dish 4' Dish 6' Dish 8' Dish 2' Dish 4' Dish 6' Dish 8' Dish Meters 5.8 GHz, EW52 Waveguide 5.8 GHz, 1/2" Coax 2.4 GHz, 7/8" Coax 2.4 GHz, 1/2" Coax 3.0 6.1 9.1 12.2 15.2 18.3 21.3 24.4 27.4 30.5 33.5 36.6 39.6 42.7 45.7 48.8 51.8 54.9 57.9 61.0 64.0 67.1 70.1 73.2 76.2 79.2 82.3 85.3 88.4 91.4 94.5 97.5 100.6 103.6 106.7 109.7 112.8 115.8 118.9 121.9 Feet 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 310 320 330 340 350 360 370 380 390 400 9.4 9.8 10.1 10.5 10.9 11.3 11.7 12.0 12.4 12.8 13.2 13.6 13.9 14.3 14.7 15.1 15.5 15.8 16.2 16.6 17.0 17.4 17.7 18.1 18.5 18.9 19.3 19.6 20.0 20.4 20.8 21.2 21.5 21.9 22.3 22.7 23.1 23.4 23.8 24.2 4.9 5.3 5.6 6.0 6.4 6.8 7.2 7.5 7.9 8.3 8.7 9.1 9.4 9.8 10.2 10.6 11.0 11.3 11.7 12.1 12.5 12.9 13.2 13.6 14.0 14.4 14.8 15.1 15.5 15.9 16.3 16.7 17.0 17.4 17.8 18.2 18.6 18.9 19.3 19.7 3.4 3.8 4.1 4.5 4.9 5.3 5.7 6.0 6.4 6.8 7.2 7.6 7.9 8.3 8.7 9.1 9.5 9.8 10.2 10.6 11.0 11.4 11.7 12.1 12.5 12.9 13.3 13.6 14.0 14.4 14.8 15.2 15.5 15.9 16.3 16.7 17.1 17.4 17.8 18.2 9.2 9.4 9.7 9.9 10.1 10.3 10.5 10.8 11.0 11.2 11.4 11.6 11.9 12.1 12.3 12.5 12.7 13.0 13.2 13.4 13.6 13.8 14.1 14.3 14.5 14.7 14.9 15.2 15.4 15.6 15.8 16.0 16.3 16.5 16.7 16.9 17.1 17.4 17.6 17.8 4.7 4.9 5.2 5.4 5.6 5.8 6.0 6.3 6.5 6.7 6.9 7.1 7.4 7.6 7.8 8.0 8.2 8.5 8.7 8.9 9.1 9.3 9.6 9.8 10.0 10.2 10.4 10.7 10.9 11.1 11.3 11.5 11.8 12.0 12.2 12.4 12.6 12.9 13.1 13.3 3.2 3.4 3.7 3.9 4.1 4.3 4.5 4.8 5.0 5.2 5.4 5.6 5.9 6.1 6.3 6.5 6.7 7.0 7.2 7.4 7.6 7.8 8.1 8.3 8.5 8.7 8.9 9.2 9.4 9.6 9.8 10.0 10.3 10.5 10.7 10.9 11.1 11.4 11.6 11.8 7.7 8.3 9.0 9.6 10.3 11.0 11.6 12.3 12.9 13.6 14.3 14.9 15.6 16.2 16.9 17.6 18.2 18.9 19.5 20.2 20.9 21.5 22.2 22.8 MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX 1.7 2.3 3.0 3.6 4.3 5.0 5.6 6.3 6.9 7.6 8.3 8.9 9.6 10.2 10.9 11.6 12.2 12.9 13.5 14.2 14.9 15.5 16.2 16.8 17.5 18.2 18.8 19.5 20.1 20.8 21.5 22.1 22.8 MAX MAX MAX MAX MAX MAX MAX

-1.3

-0.7 0.0 0.6 1.3 2.0 2.6 3.3 3.9 4.6 5.3 5.9 6.6 7.2 7.9 8.6 9.2 9.9 10.5 11.2 11.9 12.5 13.2 13.8 14.5 15.2 15.8 16.5 17.1 17.8 18.5 19.1 19.8 20.4 21.1 21.8 22.4 MAX MAX MAX

-4.3

-3.7

-3.0

-2.4

-1.7

-1.0

-0.4 0.3 0.9 1.6 2.3 2.9 3.6 4.2 4.9 5.6 6.2 6.9 7.5 8.2 8.9 9.5 10.2 10.8 11.5 12.2 12.8 13.5 14.1 14.8 15.5 16.1 16.8 17.4 18.1 18.8 19.4 20.1 20.7 21.4 7.1 7.3 7.4 7.5 7.7 7.8 7.9 8.0 8.2 8.3 8.4 8.6 8.7 8.8 9.0 9.1 9.2 9.3 9.5 9.6 9.7 9.9 10.0 10.1 10.3 10.4 10.5 10.6 10.8 10.9 11.0 11.2 11.3 11.4 11.6 11.7 11.8 11.9 12.1 12.2 1.1 1.3 1.4 1.5 1.7 1.8 1.9 2.0 2.2 2.3 2.4 2.6 2.7 2.8 3.0 3.1 3.2 3.3 3.5 3.6 3.7 3.9 4.0 4.1 4.3 4.4 4.5 4.6 4.8 4.9 5.0 5.2 5.3 5.4 5.6 5.7 5.8 5.9 6.1 6.2

-1.9

-1.7

-1.6

-1.5

-1.3

-1.2

-1.1

-1.0

-0.8

-0.7

-0.6

-0.4

-0.3

-0.2 0.0 0.1 0.2 0.3 0.5 0.6 0.7 0.9 1.0 1.1 1.3 1.4 1.5 1.6 1.8 1.9 2.0 2.2 2.3 2.4 2.6 2.7 2.8 2.9 3.1 3.2

-4.9

-4.7

-4.6

-4.5

-4.3

-4.2

-4.1

-4.0

-3.8

-3.7

-3.6

-3.4

-3.3

-3.2

-3.0

-2.9

-2.8

-2.7

-2.5

-2.4

-2.3

-2.1

-2.0

-1.9

-1.7

-1.6

-1.5

-1.4

-1.2

-1.1

-1.0

-0.8

-0.7

-0.6

-0.4

-0.3

-0.2

-0.1 0.1 0.2 Table 3-C: Transmitter Output Power Adjustment, +6 dBW EIRP Installations

(Such as Canada) SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-37 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Feeder Length Meters Feeder Length Feet TRANSMITTER POWER (dBm) 2.4 GHz, 1/2" Coax 2.4 GHz, 7/8" Coax 4' Dish 6' Dish 8' Dish 4' Dish 6' Dish 8' Dish 3.0 6.1 9.1 12.2 15.2 18.3 21.3 24.4 27.4 30.5 33.5 36.6 39.6 42.7 45.7 48.8 51.8 54.9 57.9 61.0 64.0 67.1 70.1 73.2 76.2 79.2 82.3 85.3 88.4 91.4 94.5 97.5 100.6 103.6 106.7 109.7 112.8 115.8 118.9 121.9 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 310 320 330 340 350 360 370 380 390 400 23.4 23.8 24.1 24.5 24.9 25.3 25.7 26.0 26.4 26.8 27.2 27.6 27.9 28.3 28.7 29.1 29.5 29.8 MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX 22.0 22.4 22.8 23.2 23.6 23.9 24.3 24.7 25.1 25.5 25.8 26.2 26.6 27.0 27.4 27.7 28.1 28.5 28.9 29.3 29.6 MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX 21.2 21.6 22.0 22.4 22.7 23.1 23.5 23.9 24.3 24.6 25.0 25.4 25.8 26.2 26.5 26.9 27.3 27.7 28.1 28.4 28.8 29.2 29.6 MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX 23.2 23.5 23.7 23.9 24.2 24.4 24.6 24.8 25.1 25.3 25.5 25.8 26.0 26.2 26.5 26.7 26.9 27.1 27.4 27.6 27.8 28.1 28.3 28.5 28.8 29.0 29.2 29.4 29.7 29.9 MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX 21.9 22.1 22.4 22.6 22.8 23.0 23.3 23.5 23.7 24.0 24.2 24.4 24.7 24.9 25.1 25.3 25.6 25.8 26.0 26.3 26.5 26.7 27.0 27.2 27.4 27.6 27.9 28.1 28.3 28.6 28.8 29.0 29.3 29.5 29.7 29.9 MAX MAX MAX MAX 21.1 21.3 21.5 21.8 22.0 22.2 22.4 22.7 22.9 23.1 23.4 23.6 23.8 24.1 24.3 24.5 24.7 25.0 25.2 25.4 25.7 25.9 26.1 26.4 26.6 26.8 27.0 27.3 27.5 27.7 28.0 28.2 28.4 28.7 28.9 29.1 29.3 29.6 29.8 30.0 Table 3-D: Transmitter Output Power Adjustment for 2.4 GHz, USA Installations PAGE 3-38 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.13.1 Output Power Adjustment The LYNX.sc radio requires professional installation. In certain cases, it is necessary to adjust the output power from the factory setting, for example:

v to meet EIRP (effective isotropic radiated power) limits, such as +6 dBW in Canada. v to meet transmitter output limits in the 2.4 GHz band for USA installations. v to avoid exceeding the maximum far-end RSL of 0 dBm. v to coordinate a hub or repeater location. To ensure maximum protection of the radio circuits, always ensure the antenna connector is terminated when power is applied. For precise measurement of transmitter power, a calibrated RF power meter (such as the HP 435B with Power Sensor HP8481) is recommended. This power sensor can be connected directly to the output of the radio without exceeding the power rating. With some power meters, it may be necessary to place a calibrated in-line fixed attenuator between the radio antenna port and the power meter so as to not exceed the power meters maximum input level. Thruline power meters do not operate at LYNX.sc RF frequencies. If adjusting the output power to meet an EIRP limit, it will be first necessary to calculate the overall system gains and losses, including feeder losses for the type of transmission line installed and the antenna gain. Also refer to Table 3-C or 3-D for transmitter output power settings where installed with various transmission line lengths and antenna sizes. You may determine the radio transmit power for EIRP limited installations by the following equation:

Tx Power (dBm) = EIRP Limit(dBm) + Feeder Loss(dB) - Antenna Gain(dB) In the USA, 2.4 GHz models have an output limit which is determined by:

Tx Power (dBm) = 30 - [(Antenna Gain - 6)/ 3] + Feeder Loss Output power may be adjusted using a small screwdriver and rotating the potentiometer which is recessed behind the front panel. Clockwise rotation increases output power while counter-clockwise rotation decreases output power. In lieu of a calibrated RF power meter, the PWR test port voltage can be used to estimate the output power. Figures 3-16 & 3-17 illustrate the voltage reading for various output power levels. The factory test data sheet should be used to establish a more precise setting of this adjustment. After setting the correct output power, place the cover cap found in the installation accessory kit over the front panel receptacle. SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-39 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.13.2 Loopback/BER Testing When a pair of LYNX.sc radios are installed and communicating with each other, a loopback or BER test can be performed to evaluate the link performance. The LYNX.sc uses an internal test signal for loopback. Alternatively, an external test signal can be injected, as described in Section 3.12.4. Any E1 test pattern may be used to make measurements at one end of the link, provided the test sequence contains adequate 1s density, which is no more than 15 consecutive zeros. A 215-1, QRSS or 3 in 24 test may be used. However a 223-1 test will violate the 1s density requirement. To loop around the far-end radio, press ENABLE and hold for approximately 3 seconds. then release the Loopback ENABLE button on the front panel of the near-end radio. The ENABLE LED should now be blinking. If the ENABLE loopback button LED is illuminated and not blinking, this means the far-end radio has initiated loopback

(either manually or through the DIAGNOSTICS port). When loopback is enabled using the internal test signal, the ERROR LED should not illuminate if the path is operating error-free. If the ERROR LED illuminates, this means that at least one bit error has occurred. The DATA LOSS LED will illuminate if the external test signal mode has been selected (see Section 3.12.4) and there is no external test signal present at any of the CEPT-1 ports. When using external test mode and an external test signal, the ERROR LED function does not apply. In external test mode the ERROR LED will not illuminate, even when errors are present. PAGE 3-40 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 An external BER test set is required for statistical BER analysis. Disconnect all external CEPT-1 signals and connect the BER test set to the input and output BNC connectors. Select external test mode (see Section 3.12.2) and initiate loopback using the ENABLE loopback button. Now the BER test can be initiated. Section 4.10 describes BER testing in more detail. Loopback may be turned off at either end of the link by simply pressing the ENABLE button at either end. If two BER test sets are used to measure the link performance

(one at each end) separately in each direction, frame slips will occur unless the BER test sets are synchronized with one test set as the master and the other as the slave. For multiple capacity radio models, repeat all operations for the other channels if desired. For multiple capacity radio models, only one loopback channel may be used at any one time. Loopback cannot be performed on more than one channel. SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-41 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.13.3 Error LED Mode Selection The ERROR LED illuminates if any errors are present in the data stream during loopback. This LED is only functional when using the internal test signal. The default mode for this LED is latched. That is, when a single error occurs, the LED illuminates and stays lit until loopback is turned off. This mode is especially useful for long term (overnight) testing, or any time that an operator is not watching the radio during loopback testing. There is an optional mode for this LED which is unlatched. This allows the user to view the error rate. In this mode, the LED will flash on each time a single or multiple error occurs. The LED turns off if no further errors occur. This mode can be useful if a BER test set is not available and the user wishes to determine the nature of any error conditions (bursting, dribbling, occasional). In unlatched mode, when any errors occur, the ERROR LED will illuminate for a minimum of one second. If errors continue within this one second interval, the LED will remain on until there are no errors for 1 second. The two modes for this LED are selected by a rear panel DIP switch, as shown in Figure 3-18. Figure 3-18: Error LED Mode Selection In the LED unlatch mode, after 100 errors the ERROR LED will remain lit to indicate excessive errors. PAGE 3-42 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.14 Additional Connections There are additional customer connections which are optional and are not required to make the LYNX.sc operational but may prove useful. 3.14.1 Orderwire Connection and Address Selection Orderwire is a telephone type wayside service which allows users of the LYNX.sc radio to establish voice communications from one radio to another, either directly to the companion far-end, or through a repeater configuration, or several repeater configurations. Telephone connection specifications:

REN (Ringer Equivalency Number) DTMF tones Ringing Voltage

(Ringing voltage is adequate for modern solid state ringers, NOT for the older mechanical type ringers) 1.0 B within 1.5% of nominal freq. 48 VDC, typical This Orderwire service does not affect the normal radio transmission of E1 traffic. Refer to Section 2.3.5 for the telephone specifications. For simple near-end to far-end communications, follow the steps below:

1. Using a small screwdriver, set the address of both terminals by rotating the address rotary selection switches on the rear panel of the LYNX.sc radio. The address is a two digit number

(from 01 to 99). Each LYNX.sc terminal in the network should have a unique address. This address acts like a phone number for other users to call a particular terminal. Each LYNX.sc terminal should have a unique address. Radio pairs (links) are shipped from the factory with addresses set to 01 or 02. Therefore, if only one pair is being used, address selection may not be necessary. Also, in a connected spur network, it may be desirable to maintain orderwire telephone addresses between 01 and 08 because the address doubles as the NMS/TBOS net address which is limited to the addresses 01 through 08 (see Section 3.14.3 for more information). SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-43 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Figure 3-19: RJ-11 Orderwire Telephone Connection 2. 3. Using a standard RJ-11 telephone cable, connect a standard electronic telephone (a touch tone phone, complete with dialer; a handset by itself will not work) to the Orderwire connector on the LYNX.sc front panel. This connector is wired identically to a standard two-

wire telephone jack, see Figure 3-19 for details. With a telephone connected to each LYNX.sc terminal on opposite ends of the link, either telephone can be used to dial-up the far-end location. Simply pick up the handset of the near-end telephone and dial the two-digit address of the far-end LYNX.sc terminal. The far-

end terminals internal ringer and the connected telephone will ring, and if answered, two-

way full-duplex voice communication is established. If using the Orderwire or Network management functions, all LYNX.sc radios connected must have unique address settings

(telephone numbers). The orderwire address is set by two rotary switches on the rear panel of the LYNX.sc radio. Use as small screwdriver to select the orderwire address (01 through 99). PAGE 3-44 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 4. If the LYNX.sc radios are connected in a repeater configuration, Orderwire services can be established to all LYNX.sc terminals in the network by implementing a connection of their rear-

panel connectors between repeater terminals. At the repeater site, a cable can be connected to the two LYNX.sc terminals between their rear panel VF 25-pin connectors as shown in Figure 3-20. With this cable in place, the Orderwire function will operate at terminals at each end of the repeater and at the repeater site. This function can be continued through several repeater sites if desired. For hub connections of 3 or more LYNX.sc radios at the same site, an external 4-

wire bridge is required to connect all radios to the orderwire. The orderwire system can be integrated with orderwire equipment supported by many other vendors. If your existing orderwire network uses 2 digit addressing, and 0 dBm VF interface, it can be connected to a LYNX.sc as shown in Figure 3-20. Dialing a V (star key) on the orderwire telephone implements an all call feature which rings all connected radios. Also, if a phone anywhere in the connected network has accidentally been left off-

hook, the # (pound key) key can be used to mute all off-hook handsets until they are placed on and off hook again. The orderwire operates like a party line. All telephones provide communication to all other telephones in the connected network. Even if a particular telephone does not ring, it can still be used to talk and listen to any ongoing orderwire activity if the orderwire is in use at other terminal locations. VF Connector OrderWire Connection Figure 3-20: VF Port Connection SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-45 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.14.2 Alarm Connections External alarm outputs are provided at the 25-pin, D-type subminiature ALARM connector. There are two Form C summary alarm relays capable of switching 30 VDC at 1 A. Also, individual alarm logic outputs capable of sourcing and sinking 1mA are provided. These individual alarms interface to a single standard TTL load. When the unit is IN ALARM = 0, the TTL output is 0 V to 0.5 V. When the unit is NO ALARM = 1, the TTL output is +3.5 V to +5.5 V. See Table 3-E and Figure 3-21 for Alarm Connections. The summary alarm (Form C relay) is activated by any near-end front panel LED alarm condition, including if the loopback mode is enabled. The out-of-service summary alarm (Form C relay) is activated by any of the following alarm conditions:

v v v RX SYNC Radio Fail Loopback Enabled Figure 3-21: Pin Connections, ALARM Interface PAGE 3-46 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 PIN 2 PIN 4 PIN 6 PIN 8 PIN 16 NC, SUMMARY ALARM, FORM C - normally closed connection on summary alarm relay. DATA LOSS (1 or 1&2) - in alarm if no incoming data is received into the transmitter for channel 1 (for the 4xE1 model, includes channel 2). Data Loss is activated when the input signal drops below 0.97 volts for 175 bit intervals and is deactivated as soon as the input signal level rises above 0.97 volts. Radio transmits AIS to the far-end if in alarm. This alarm may be disabled by DIP switch selection

(see Section 3.12.4). DATA LOSS (2 or 3&4) use essentially the same description as Data Loss (1 or 1&2), for channel 2 (for the 4xE1 model, channels 3&4). PIN 17 NO, OUT OF SERVICE SUMMARY ALARM, FORM C - normally open connection on out-of-

service summary alarm relay. Closed when in alarm. BER - in alarm when the received signal is degraded to an error rate above radio threshold

(approximately 1 x 10-6) AIS OUT - in alarm when the BER exceeds 1 x 10-3 for the received signal, or when there is an RX SYNC alarm condition. Near-end radio CEPT-1 line output has AIS when in alarm. This alarm may be disabled as described in Section 3.12.5. PIN 18 PIN 19 C, OUT OF SERVICE SUMMARY ALARM, FORM C - common connection for the out-of-

service summary alarm relay. NC, OUT OF SERVICE SUMMARY ALARM, FORM C - normally closed connection on out-

of-service summary alarm relay. Open when in alarm. PIN 10 FAN - in alarm when one or both of the internal fans are not operative. PIN 21 NOT USED PIN 12 FAR-END - in alarm when the far-end radio has an alarm condition. PIN 22 NOT USED PIN 14 NO, SUMMARY ALARM, FORM C - normally open connection on summary alarm relay. Closed when in alarm. PIN 24 TX PWR MON - voltage equal to the TX PWR front panel voltage. PIN 15 C, SUMMARY ALARM, FORM C - common connection on the summary alarm relay. PIN 25 RSL MON - voltage equal to the RSL front panel voltage. Equals far-end RSL if DISPLAY FAR END button is pressed and held. PINS 1, 3, 5, 7, 9, 11, 20, & 23 GROUND, CHASSIS CONNECTION Table 3-E: Alarm Interface Connections All alarms are active for a minimum of one second, or as long as the alarm condition persists, which ever is longer. TTL signals are in alarm when there is a TTL zero condition

(0 V to 0.5 V). SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-47 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.14.3 Diagnostics Port Operation The Diagnostics Port is used to retrieve diagnostic or network management information about the LYNX.sc radios by means of a computer connection. This can be accomplished locally or remotely. Remote diagnostic port connections require either a modem (not included) connection be made to the serial port, when a local dial-up phone line is available at a radio site, or by means of direct connection through the AUX DATA port (Service Channel). The use of the AUX DATA channel can provide a network management port where serial interface data is available from all LYNX.sc radios in a network, provided that they are configured properly for this type of operation. (This section and Section 3.14.4 describe this further). The diagnostics port allows connection of either EIA standard RS-232 or RS-422 devices to poll and receive status of the LYNX.sc radio. This serial port provides similar information to that which is normally available to a local operator by means of visual alarms and status (front panel LEDs, ADDRESS, DIP switch settings etc.), including voltage level measurements (such as RSL, PWR) and alarm port (see Section 3.14.2) status. The diagnostics port can also provide extended information including some advanced diagnostics and configuration information. Any information that is available on the far-end terminal is also available at the near-end Diagnostics port (such as far-

end RSL, far-end alarms) by means of bridging the AUX DATA port (as described in Section 3.14.4). A DIP switch is used to define the command protocol for this port as shown in Figure 3-22. The default setting is for TBOS commands (as described later in this section). The other setting is for factory use only. SW1 Figure 3-22: Diagnostic Port Protocol Selection PAGE 3-48 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.14.3.1 Diagnostics Port using RS-232 For RS-232 diagnostics connection to the LYNX.sc radio, connect the serial device (modem, computer, terminal) to the male 9-pin subminiature connector in accordance with Figure 3-23. Figure 3-23: RS-232 Diagnostic Port Connections Pins 6 communications to operate properly. through 9 must not be connected for RS-232 SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-49 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.14.3.2 Diagnostics Port using RS-422 For RS-422 Diagnostics connection to the LYNX.sc radio, connect to the serial device (modem, computer, terminal) to the male 9-pin subminiature connector in accordance with Figure 3-24. Figure 3-24: RS-422 Diagnostic Port Connections Do not connect devices to both the RS-232 and RS-422 connections of the Diagnostics Port. This will cause data conflicts that will result in errors over the interface. PAGE 3-50 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.14.3.3 TBOS Protocol and Map The diagnostics port is configured for an open industry standard protocol, called Telemetry Byte Oriented Serial (TBOS). TBOS is a poll and response protocol that operates on a RS-422 4-wire interface, one pair for transmit data (requests) to the radio, and one pair for receive data (responses) from the radio. TBOS is asynchronous, serial, half duplex transmissions of ASCII words which consist of one start bit, 8 data bits, odd parity and two stop bits at 1200 baud. The connected terminal (remote or local) can poll the radio and determine status of the connected LYNX.sc radio. The LYNX.sc is also able to communicate TBOS commands over the RS-232 connections, instead of the RS-422 connections if desired. TBOS operates with a bit-map structure where each bit that the connected LYNX.sc radio sends to the TBOS terminal has a specific meaning with regard to status, alarms or controls. All TBOS network elements require a map for the network management software to interpret their responses to queries from the terminal. Table 3-F provides the TBOS map for the E1 LYNX.sc radios. The near-end RSL and Tx power test point voltages are encoded as 8 bit words that can be converted into reference voltages (the same as at the front panel of the radio. The address of the radio (see Section 3.14.1) serves as the display page number for the TBOS data. Since TBOS is limited to eight (8) displays of data, it is required that addresses of 01 through 08 be used for LYNX.sc radios in TBOS networks. Any radio with addresses other than 01 through 08 will not report to the TBOS bit-map. In order to view status displays of far-end radios, or other radios in the connected network, the AUX DATA port must be in Bridge (default) mode as described in Section 3.14.4. Alarm points within the TBOS map behave like the radio front and rear panel alarms. If DIP switches have been set to disable alarms, the alarms are disabled within the TBOS map. SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-51 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Byte Point Bit Type*

Scan Point Definition Control Point Definition Notes Loopback Channel 1 On/Off Loopback Channel 2 On/Off Loopback Channel 3 On/Off Loopback Channel 4 On/Off 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 S S S S N/A S S S A A A A A A A A A A A A S S S S S S S/C S/C S/C S/C S S N/A N/A N/A N/A S S S S S S S S S S S S S S S S S S S S S S S S S Model ID MSB Model ID LSB+2 Model ID LSB+1 Model ID LSB Future Use Channel Plan ID MSB Channel Plan ID LSB Channel Plan Tx High/Low Radio Fail Alarm AIS Out Alarm Fan Alarm Rx Sync Alarm Loopback Error Alarm BER Alarm Far-End Alarm Telemetry Down Alarm Data Loss Ch1 Alarm Data Loss Ch2 Alarm Data Loss Ch3 Alarm Data Loss Ch4 Alarm Data Loss Ch1 Alarm Disabled Data Loss Ch2 Alarm Disabled Data Loss Ch3 Alarm Disabled Data Loss Ch4 Alarm Disabled Loopback Test Source Loopback Error LED Mode Loopback Channel 1 Enabled Loopback Channel 2 Enabled Loopback Channel 3 Enabled Loopback Channel 4 Enabled AIS Disabled Bridge Disabled (Aux Enabled) Future Use Future Use Future Use Future Use Far-End Address Invalid Far-End Address MSB Far-End Address LSB+1 Far-End Address LSB Near-End RSL MSB Near-End RSL MSB-1 Near-End RSL MSB-2 Near-End RSL MSB-3 Near-End RSL MSB-4 Near-End RSL MSB-5 Near-End RSL MSB-6 Near-End RSL MSB-7 Near-End Tx Power MSB Near-End Tx Power MSB-1 Near-End Tx Power MSB-2 Near-End Tx Power MSB-3 Near-End Tx Power MSB-4 Near-End Tx Power MSB-5 Near-End Tx Power MSB-6 Near-End Tx Power MSB-7 Both Fans Bad Tx Synth Unlock Rx Synth Unlock Input Line Driver Digital Hardware N/A N/A N/A Future Use Future Use Future Use 0011 = 2.4 GHz E1 (Model 31500) 0100 = 5.8 GHz E1 (Model 31400) 0101 = 5.8 GHz 2xE1 (Model 31700) 1100 = 5.8 GHz 4xE1 (Model 31850) SW3 pos 6 00=A, 01=B, 10=C SW3 pos 7 Defaulted to 00 (A) for Model 31800 SW3 pos 8 (1 = Tx High, i.e. A2, B2, C2) Equal to F/P alarm Equal to F/P alarm Equal to F/P alarm Equal to F/P alarm Equal to F/P alarm Equal to F/P alarm Equal to F/P alarm Equal to F/P alarm Equal to F/P alarm Equal to F/P alarm, where applicable Equal to F/P alarm, where applicable Equal to F/P alarm, where applicable SW1 pos 1 SW1 pos 2, where applicable SW3 pos 3, where applicable SW3 pos 4, where applicable SW1 pos 3 (0 = Internal, 1 = External) SW1 pos 4 (0 = Latched, 1 = Momentary) Front panel switch Front panel switch, where applicable Front panel switch, where applicable Front panel switch, where applicable SW1 pos 5 SW1 pos 8 1=Address>08 000=01, 001=02, 010=03, 011=04, 100=05, 101=06, 110=07, 111=08 RSLVOLTAGE Binary Byte(integer) x 0.04 Volts Note The 8-bit binary value (0-255) represents RSL values between -50 dBm and threshold. Radio paths with higher RSL values will read approximately five (5) to ten (10) VDC on the radios front panel test point but be limited to a maximum binary reading of 255 which represents 5 VDC. 8-bit byte derives voltage or dBm TxPWRVOLTAGE Binary Byte(integer) x 0.02 Volts Only applies if Point 11=1 Only applies if Point 9=1 Only applies if Point 9=1 Only applies if Point 9=1 Only applies if Point 9=1 Key:

A = Alarm S = Status C = Control Table 3-F: TBOS Map for the LYNX.sc E1s PAGE 3-52 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.14.4 AUX DATA (Digital Service Channel) Connection The AUX DATA port is a separate wayside serial port which can be configured to allow the connection of any user serial data (to 9600 baud) through the radio network. In the default configuration, this service channel is bridged to the diagnostics port, providing TBOS network management for far-end radios including radio network management through repeaters and hubs. Connection to the AUX DATA port is an RS-232 or RS-422 serial interface, identical to the diagnostics port (see Section 3.14.3). This port does not affect the E1 traffic on the LYNX.sc radio. For TBOS network management, or when the AUX DATA port is used as a clear service channel, co-located radios can be wired to one another to provide the information throughout the network. At a repeater or hub location, bridging is accomplished by cable connections between co-located LYNX.sc radios, via their AUX DATA ports, as shown in Figure 3-25 and 3-26. Figure 3-27 illustrates the pin-to-pin connections for this configuration. There is a related DIP switch position, as shown in Figure 3-27, that makes the AUX DATA port usable for customer data instead of the TBOS network management information. The factory default setting for this DIP switch is for TBOS network management. For non-TBOS external site management systems can be used with the LYNX.sc radios; Figure 3-

26 shows a typical application. Here the reporting relies on external devices to communicate over the clear service channel of the LYNX.sc radio. Each radio is given a site location (see Section 3.14.1) and information on the radio status and control is fed through the diagnostic port to a remote terminal unit (RTU). These RTUs have the capability of providing for other external inputs at the remote site, for complete network management. Communication from each RTU is fed via the RS-

232 port to the AUX DATA connector on the radio, in this configuration no bridging is required. RTUs that do not support TBOS can alternatively connect to the LYNX.sc alarm connector for discreet TTL alarms and/or test point voltages. If you are using TBOS network management and want full information on in a single-hop application), the bridge function must be enabled. far-end

(even radio the The service channel can only be used for TBOS network management or for Aux data, not both. When selected for TBOS, no other data should be connected to the AUX DATA port. SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-53 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Antenna Antenna T1 Antenna Antenna LYNX.sc Aux. DATA LYNX.sc LYNX.sc LYNX.sc Diagnostics Diagnostics 2 X T1 Aux. DATA T1 LYNX.sc Diagnostics Antenna Antenna T1 Diagnostics LYNX.sc Diagnostics T1 Figure 3-25: Repeater and Hub TBOS Radio Network Management T1 LYNX.sc Diag. AUX. LYNX.sc Diag. AUX. T1 LYNX.sc AUX Diag 01 Site Address TBOS Info at this radio RS-232 Network Manager 02 Site Address TBOS Info at this radio 03 Site Address TBOS Info at this radio RS-232 Remote Terminal Unit LYNX.sc Diag. AUX. T1 04 Site Address TBOS RS-232 Info at this radio Remote Terminal Unit Figure 3-26: Repeater Application with Site Network Management PAGE 3-54 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Figure 3-27: AUX DATA Cable Connection for Repeater/Hub Figure 3-28: AUX Data Selection SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-55 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.14.5 Protect Port Connection (Preliminary Information) This feature is not yet available as of the publishing date of this manual. The protect port is an 8-pin modular jack connection which is used in conjunction with an auxiliary piece of equipment called a LYNX.SC.mhs. The LYNX.sc protection port implements control information for the purposes of Monitored Hot Standby (MHS) or Space Diversity (SD) radio configurations. Purchase of the LYNX.SC.mhs equipment is required to implement this feature of the LYNX.sc radio. Details of the specific connection requirements to this equipment are supplied in the LYNX.SC.mhs manual. MHS is a configuration of equipment which essentially supports a back-up radio, in case of radio hardware failure. For the LYNX.sc this is accomplished by connecting the antenna and E1 connections to the LYNX.SC.mhs unit, and then connecting the LYNX.SC.mhs unit to two separate and identical LYNX.sc radios. The LYNX.SC.mhs unit provides the capability to switch between connected LYNX.sc radios in case of a radio hardware failure. There is an interruption in radio traffic when this switching occurs, however, radios are typically able to resynchronize and establish communications in a few seconds (depending on path length and path availability). A typical MHS configuration is shown in Figure 3-29. Figure 3-29: MHS Configuration PAGE 3-56 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 3.14.6 Protect Port Connection (Preliminary Information) This feature is not yet available as of the publishing date of this manual. Space Diversity (SD) is a similar application for radios where there is a back-up path for the radio in case of radio failure or path outage problems. This type of application is typically configured as two separate radios at the same site connected to two separate antennas. The separate antennas yield a slightly different path and therefore may provide better performance in cases of path outage due to weather or interference. There is an availability improvement due to multipath fading in a SD configuration as compared to a non-protected system configuration. A representative SD configuration is shown in Figure 3-30. Figure 3-30: SD Configuration SECTION 3: INSTALLATION & ADJUSTMENTS PAGE 3-57 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Your Notes on the LYNX.sc Radio PAGE 3-58 SECTION 3: INSTALLATION & ADJUSTMENTS INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 4. Troubleshooting 4.1 Regular Maintenance The LYNX.sc radios do not require any regular maintenance, however, it is prudent to monitor the radio link at regular intervals to assure that the link conditions are not changing. When visiting a radio site for maintenance, the following items may be checked and their results recorded:

v RSL Voltage v PWR Voltage v Far-end RSL Voltage v Alarm conditions v Verify radio has adequate ventilation If any alarm conditions exist, they should be recorded, and troubleshooting procedures from this Section of the manual should be followed. SECTION 4: TROUBLESHOOTING PAGE 4-1 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 4.2 Changing Frequency Plans The LYNX.sc RF frequency selections are listed in Section 3.5. The near-end radio and the far-end radio must be corresponding (e.g. A1 / A2). The frequency of a given LYNX.sc terminal is set by the specific filter, the physical orientation of this assembly, and the setting of corresponding DIP Switches. (See Section 3.12.1 for more details.) With respect to a given filter, the frequencies are fixed, because tuned RF filters are required for normal operation. Changing of the (pretuned) radio frequencies may be required when installing spares or for special situations, such as interference mitigation. This is accomplished by installing an alternate filter or reorienting the existing filter. For any given model of LYNX.sc (2.4 GHz 1xE1, 2.4 GHz 2xE1, 5.8 GHz 1xE1, 5.8 GHz 2xE1, or 5.8 GHz 4xE1), the frequency channel can be changed by swapping and /or reorienting the filter. It is not necessary to remove the cover assembly of the LYNX.sc 1. Remove any cables connected to the antenna connector on the diplexer (filter) and then remove the two screws which mount the filter to the LYNX.sc chassis. 2. Slowly remove the filter from the chassis being careful to not endanger the cables that are connected to the rear side of the filter. 3. Disconnect the two SMA connectors that are attached to the rear of the filter with a 5/16 open end wrench. 4. Select the new filter or orient the existing filter such that the frequency channel label on the filter (showing the DIP switch positions) is right-side-up corresponding to the desired frequency channel. 5. Connect the two SMA connectors to the new or reoriented filter with the 5/16 open end wrench. 6. Slowly place the wired filter assembly so that it is flush with the rear panel. 7. Install the two screws which mount the filter to the rear panel. 8. Refer to the rear panel filter label or Section 3.12.1 for DIP Switch settings to correspond to the new filter and reattach the antenna cable. As an example, the filter assemblies of an A1 and A2 terminal are identical. They are simply installed differently. An A1 terminal can be changed into an A2 by removing the filter and rotating it 180 degrees and reinstalling the filter. The DIP switch positions need to match the filter orientation, per the appropriate filter label. PAGE 4-2 SECTION 4: TROUBLESHOOTING INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 4.3 Using a Spare Terminal One spare LYNX.sc terminal of a given model type (2.4 GHz 1xE1, 2.4 GHz 2xE1, 5.8 GHz 1xE1, 5.8 GHz 2xE1, or 5.8 GHz 4xE1) will service any other radio in that same model type, independent of frequency channel plan. For example, a 5.8 GHz E1 channel A2 can be used as a spare for any A, B or C channel E1 radio at 5.8 GHz. See Section 4.2 for changing frequencies of a spare radio. Customers with several radios, or radios in critical operations are encouraged to purchase one or more spare radios of each model in their system. This will allow rapid restoration of radio service in the unlikely event of a radio failure. SECTION 4: TROUBLESHOOTING PAGE 4-3 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 4.4 Technical Support Western Multiplex provides 24-hour telephone technical support for installed LYNX.sc radios. Customers are encouraged to troubleshoot the radio and link in accordance with the latter part of this section in this manual before contacting Western Multiplex. Western Multiplex also has a limited supply of LYNX.sc radios that can be loaned to out-of-service customers for installation while units are being repaired. Loaner supply is limited, and is only used for critical applications on a first-come, first-served basis. Customer service #:

+1 408 542-5390 PAGE 4-4 SECTION 4: TROUBLESHOOTING INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 4.5 Repair Policy The LYNX.sc terminal includes comprehensive alarm indicators designed to diagnose potential faults. Should a fault occur, it often may be resolved by operator adjustment. Should a fault occur that cannot be resolved by operator adjustment and has been confirmed by looping terminals together on the bench (See Section 4.9), then the equipment should be returned to the factory for repair. The LYNX.sc radio is a complex system not designed for user repair. Do not remove the cover or open any part of the LYNX.sc terminal. The complete LYNX.sc terminal should be sent back in its original packing material for factory repair. Please contact the factory in advance of returning the product. You will be assigned a Return Material Authorization (RMA) number that authorizes your return. Units sent to the factory without an RMA number may be delayed in the processing of the repair. Be sure to include the following information:

v RMA number v description of the problem v your name and telephone number v return shipping address v urgency of repair Please refer to the published Warranty policy for repair policy details. LYNX.sc radios should be packaged in their original packing boxes for shipment whenever possible Western Multiplex can provide an empty box shipment to facilitate proper packaging. Regardless, proper and adequate packaging must be used for shipments to protect the radio(s) from damage. Western Multiplex can not be held responsible for any repairs due to inadequately packed materials. Damage caused by improper packing will likely result in higher repair costs and delays (refer to the Warranty section at the beginning of this manual). SECTION 4: TROUBLESHOOTING PAGE 4-5 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 4.6 Front Panel Status LEDs There are several front panel status LEDs on the LYNX.sc radio. These LEDs indicate conditions where either a hardware failure has occurred or the radio link is not optimum. In many cases, a combination of LEDs may be illuminated. The following sections describe the necessary troubleshooting procedures should any LED(s) indicate a problem during or after installation. PAGE 4-6 SECTION 4: TROUBLESHOOTING INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 4.6.1 DATA LOSS Alarms Function:

These DATA LOSS Alarms indicate that no CEPT-1 signal is present at the rear panel CEPT-1 interface. On a multiple-capacity radio, the DATA LOSS 1 alarm relates to the DATA 1 ports while the DATA LOSS 2 alarm relates to the DATA 2 ports. On the 4xE1 model, DATA LOSS 1&2 are combined and DATA LOSS 3&4 are combined. This alarm does not indicate a radio hardware failure. The capacity of the radio will determine how many DATA LOSS LEDs there are on the front panel. Sometimes a double-capacity radio is put into service with only one input channel active, with the second channel planned for future growth. In this case, the DATA LOSS 2 alarm will be active because no CEPT-1 signal will be present. This alarm can be defeated by selecting a rear panel DIP switch as described in Section 3.12.4. When there is a data loss condition, even if the data loss alarm has been disabled, the LYNX.sc radio injects AIS into the (RF) transmitted CEPT-1 signal. Possible Causes:

v No CEPT-1 connection present at rear panel v Improper pin connections of CEPT-1 connector v No data on CEPT-1 input connector SECTION 4: TROUBLESHOOTING PAGE 4-7 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Recommended Actions:

1. Check to make sure that there is a CEPT-1 connection present on either of the connectors

(BNC) for the channel in alarm. On a multiple-capacity radio, if the alarm is on a channel which is unused at this time, the alarm condition can be disabled by a rear panel DIP switch, as described in Section 3.12.4. 4. 5. 6. Verify that the CEPT-1 line has data active at the radio connection. This can be accomplished using a BER tester or signal analyzer. Also, signal activity can be verified by using an oscilloscope. Verify that pin connections have been made properly (in accordance to Section 3.11). Make sure that you have connected the CEPT-1 with respect to the transmitting device. Connect a BER tester or signal analyzer to the CEPT-1 Monitor INPUT port on the rear panel. PAGE 4-8 SECTION 4: TROUBLESHOOTING INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 4.6.2 BER (Bit Error Rate) Alarm Function:

This LED indicates that the traffic being received from the far-end radio is exceeding the bit error rate threshold of the radio (approximately 1 x 10-6). This indicates that radio traffic currently has errors on it which may exceed acceptable levels. This LED will stay ON as long as the BER threshold is being exceeded. In some cases, it will turn ON and OFF, in which case there are bursts of errors causing intermittent degradation to the received data. In all cases, the LED will be on for at least 1 second for any group of errors which exceed the threshold, whether they are a burst of errors or a long string of errors. If the RX SYNC alarm is on the near-end or far-end radio in addition to the BER alarm (on the same radio), the RX SYNC alarm should be the first priority for troubleshooting. Possible Causes:

v Path fading due to atmospheric conditions (usually accompanied by Far-End BER alarm) and low RSL voltage reading v Poor transmission line connections (usually accompanied by Far-End BER alarm) and low RSL voltage reading v Antenna problems, misalignment or path clearance (usually accompanied by Far-End BER alarm) and low RSL voltage reading v Interference v Received signal level (RSL) is too strong v Far-end radio transmitter circuitry is faulty or Tx Power adjusted incorrectly (too low) v Near-end radio receiver circuitry is faulty SECTION 4: TROUBLESHOOTING PAGE 4-9 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Recommended Actions:

An internal loopback test should be performed to verify that errors are occurring over the link:

v Verify that the near-end radio is set for Internal test mode and Latched Error LED (both default settings of rear panel DIP switch positions, as described in Sections 3.12.2 and 3.13.3). v Press and hold (for approximately 3 seconds, then release) the Loopback Enable switch on the front panel of one radio (this will take radios out of service). Let this test run for a few minutes. v If the ERROR LED illuminates, this is verification that errors are on the link and troubleshooting should continue. v Press the Loopback Enable switch to deactivate loopback mode. Next measure RSL by placing a voltmeter across RSL and GND test points. Compare this voltage to the Factory Test Data Sheet and estimate the RSL in dBm. Compare this to the RSL that was expected using path calculations (see Section 3.3.3). Press and hold the DISPLAY FAR END button and measure the far-end RSL (while continuing to hold the button). Compare this RSL to the Factory Test Data Sheet for the far-end radio and estimate the RSL in dBm. Again, compare this RSL to the expected RSL from the link budget calculations. If RSL from both ends of the radio are approximately the same as each other, but lower than anticipated for this installation, then the likely cause of the BER alarm(s) is excessive losses between the radios. Excessive loss problems could include the transmission line at either end, all adapters, connectors, the antennas, the antenna alignment as well as the path itself (any obstructions or clearance problems). Antenna alignment, line-of-sight and path clearance should be verified; if this does not improve RSL, all devices between the radios and their antennas at both ends should be checked. Make sure all transmission line, connectors and any other devices are properly rated for operation at the radio's frequency (2.4 or 5.8 GHz). If only one end has low RSL, this could be caused by low transmit output power from the opposite end radio. Verify that the transmitter output power of the radio opposite to the low RSL receiver has been set in accordance to path calculations, or EIRP restrictions (where applicable). Power adjustment must be performed by professional installation personnel only. The PWR test point can be used and compared with the Factory Test Data Sheet, the front panel recessed potentiometer can be turned clockwise to increase power. If an RF power meter is available, this can be connected to the RF output of the radio for precision measurement. This test will also verify that the radio transmitter is working properly. PAGE 4-10 SECTION 4: TROUBLESHOOTING INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 If one terminal (or both) has high RSL, this could be caused by a very short path or interference. To verify the possible presence of interference, remove DC power to the radio which is opposite to the one that is reading high RSL. Once power is removed, measure RSL on the remaining radio. If RSL voltage is higher than that which is listed for "Threshold" in the Factory Test Data Sheet, then an interfering signal is present. If interference is suspected, the easiest potential remedy is to swap frequency channels on both sides of the link. See Section 4.2 for details. Swap frequencies on both terminals so that they are the opposite from their original settings (e.g. change A1 into A2 and A2 into A1). Make sure that you change the DIP switch settings to correspond to the channel change. After both ends are changed, reconnect the radios and determine if the BER alarm is still active. If the BER alarm is still active, other frequency channels can be installed, or other interference countermeasures can be tried, in accordance with Section 4.8. If the BER alarm continues, an external BER test should be performed to verify the extent of bit errors on the link. See Sections 4.9 and 4.10 for details on bit error rate testing. A BERT can be connected on one side of the link, the External test mode selected on the near-end radio, loopback enabled and bit errors evaluated. If the BER is above acceptable levels, continue to troubleshoot the link. If all path related and data input problems have been pursued and the BER alarm is still active, the problem could be related to a radio failure. While radio failure is typically indicated by more severe alarm conditions, it is possible that one of the radios may be out of specification, and this could be the cause of the BER alarm. A back-to-back test will verify proper radio operation. See Section 4.9 for details. A threshold test on both radios along with a test to verify proper RF output power would be beneficial. Perform a back-to-back test before returning any radio terminal to the factory for repair. A back-to-back test verifies radio operation.

(See Section 4.9). If the radios successfully pass their back-to-back testing, the problem is likely with the path or the connections between the radio and the antenna or interference. Before reinstalling the radios, be sure to set the output power to the appropriate level for the installation and set rear panel DIP switches to the desired settings for the installation. SECTION 4: TROUBLESHOOTING PAGE 4-11 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 4.6.3 RX SYNC (Receiver Synchronization) Alarm Function:

This LED indicates that the demodulator function is not synchronizing with the intended received signal. When the RX SYNC alarm is active, the LYNX.sc radio injects AIS onto the received CEPT-1 (line transmit out), even if AIS has been disabled by rear panel DIP switch setting. Possible Causes:

v Severe path fading due to atmospheric conditions (usually accompanied by Far-End RX SYNC or BER alarm) and low RSL voltage reading v Poor transmission line connections (usually accompanied by Far-End RX SYNC or BER alarm) and low RSL voltage reading v Antenna problems, misalignment, or path clearance (usually accompanied by Far-End RX SYNC or BER alarm) and low RSL voltage reading v Improper radio settings (frequency channel, spread code) v Interference v Far-End radio transmitter circuitry is faulty v Near-End radio receiver circuitry is faulty Recommended Actions:

Check the following at each end of the link:

v Verify that rear panel filters are opposite channel plans on each end (e.g. one is A1 and other is A2). v Verify that rear panel DIP switch settings match each installed filter (see Section 3.12.1). v Verify that each radio is set to the same spreading code (see Section 3.12.3). v Verify that all connections between radios and antennas are secure and all devices between radios and antennas are rated for the radio frequency band (2.4 or 5.8 GHz). If RX SYNC alarm continues, follow recommended actions for a BER alarm as described in Section 4.6.2. PAGE 4-12 SECTION 4: TROUBLESHOOTING INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 4.6.4 AIS OUT (Alarm Indication Signal) Function:

This LED informs the user that the near-end receiver is operating at BER 1 x 10-3 or is not receiving data and is therefore injecting AIS to the line transmit out of the CEPT-1 connector. If the AIS has been disabled by rear panel DIP switch, AIS will not be injected onto the line transmit output unless there is a loss of sync (RX SYNC alarm). Possible Causes:

v Local receiver has lost lock (RX SYNC) v Local receiver is operating at BER >1 x 10-3 Recommended Actions:

1. Follow recommended actions for a RX SYNC alarm, as described in Section 4.6.3. SECTION 4: TROUBLESHOOTING PAGE 4-13 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 4.6.5 FAN Alarm Function:

This alarm activates only when one or both of the internal fans are faulty. Possible Cause:

v Faulty fan inside the radio. Recommended Actions:

1. Check environmental conditions of the radio. Assure that the ambient temperature at the radio location is within specification of the radio. If not, apply environmental conditioning to radio location or place radio at alternate location where the environmental specifications are met. 2. Visually inspect radio mounting area and ensure that right and left sides of the radio chassis are unobstructed for airflow. 3. Verify that at least one of the internal fans are operational by temporarily covering some of the ventilation holes on the right side of the radio (as you face the front panel) with a thin piece of paper. Slowly pull the paper outwards away from the ventilation holes to determine if the fan is pulling the paper toward the chassis. This can also be checked on the opposite side of the chassis to verify that the fans are pushing air out of the chassis. 4. 5. If at least one fan is working you may wish to postpone repair, as long as the unit is operating without any other errors (the radio is designed to operate with only one fan) If neither fan is working or if typical operating environment is greater than 30C, it is recommended that the unit be repaired at the soonest opportunity. Return the radio to the factory for repair. See Section 4.5 for details. PAGE 4-14 SECTION 4: TROUBLESHOOTING INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 4.6.6 RADIO FAIL Alarm Function:

The RADIO FAIL alarm indicates a known problem with the radio hardware. Possible Causes:

v Internal synthesizers are unlocked v Internal digital circuits have failed v CEPT-1 connection is incorrect Recommended Actions:

1. Disconnect the CEPT-1 connections from the rear panel. 2. If RADIO FAIL alarm clears, check CEPT-1 connections for proper pin connections and impedance as described in Section 3.11. 3. If RADIO FAIL alarm does not clear, remove power from the unit. 4. Check to make sure power supply voltages are within specification. 5. Even if the voltages were within specification, reapply power to the unit. 6. If RADIO FAIL alarm clears, place the radio back into service. 7. 8. If RADIO FAIL alarm does not clear, perform a back-to-back test to verify radio operation, as described in Section 4.9. If RADIO FAIL alarm is still active in a back-to-back test, return the radio to the factory for repair

(see Section 4.5). SECTION 4: TROUBLESHOOTING PAGE 4-15 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 4.6.7 FAR END Alarm Function:

This LED indicates that there is an alarm condition present on the far-end radio. When the DISPLAY FAR END button is pressed (and held), the status LEDs indicate the alarm conditions of the far-end radio. Possible Cause:

v One or more alarm condition(s) exist on the far-end radio Recommended Actions:

1. Press and hold the DISPLAY FAR END button and observe the LED status. 2. Follow instructions for troubleshooting the far-end radio in accordance to the appropriate LEDs which are in alarm, as described in Section 4.6.1 through 4.6.6. PAGE 4-16 SECTION 4: TROUBLESHOOTING INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 4.7 Errors in the Data Stream When the radio is in service, errors in the data stream may occur. This is usually known to the operator by either faulty data indications of downstream equipment, external bit error rate testing, or ERROR LED indications during internal loopback testing. During internal test mode loopback testing, if an error is detected, the ERROR LED will illuminate. In default mode, this lamp will stay lit during loopback testing if a single error is detected. If Loopback has been performed over a period of time and the ERROR LED does not latch on, the radio link is operating completely error-free. The ERROR LED only operates in internal test signal loopback mode. Use a BERT to detect errors when using an external test signal. See Sections 3.12.2, 3.13.2 and 3.13.3 for more details. It is possible that no alarms appear on the front panel during normal operations, but there are errors present in the data stream. If the BER LED is lit, this indicates rather severe error conditions and it is best to follow the procedures provided in Section 4.6.1. However, some errors will not result in the BER alarm (such as bipolar violations, slow "dribbling" errors, improperly terminated CEPT-1 connections or incorrect settings of switches), but will be exhibited on downstream data processing equipment or during a BER test. In other cases, there may be data errors due to atmospheric conditions (fading), interference or other reasons, but not at a high enough error level to be indicated with the BER alarm LED. In the case of these types of errors, the following information can be helpful to troubleshoot the radio link. Indications:

v In Loopback Mode, ERROR LED is illuminated v During external BER test, test equipment indicates errors v Downstream equipment (mux, channel bank, CODEC, router, etc.) indicates errors Possible Causes:

v Path fading due to atmospheric conditions v Poor transmission line connections v Antenna problems, misalignment or path clearance v Received signal level (RSL) is too strong v Far-End radio transmitter circuitry is faulty v Near-End radio receiver circuitry is faulty v Interference Recommended Actions:

1. Verify CEPT-1 wiring in accordance to Section 3.11. SECTION 4: TROUBLESHOOTING PAGE 4-17 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 2. Even if the BER alarm LED is unlit but errors continue, follow the instructions described in Section 4.6.2 PAGE 4-18 SECTION 4: TROUBLESHOOTING INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 4.8 Interference Countermeasures The recommended interference countermeasures available to the LYNX.sc operator are as follows:

1. Short Paths The single most effective countermeasure against interference is to maintain "short path" length. This may be achieved by dividing long paths into multiple small paths by cascading hops. Intermediate repeaters may be formed using back-to-back LYNX.sc terminals and transmit output power reduced, if required. By definition, "short path" is defined as a path where fades are extremely rare and signal levels vary by no more than 3 dB during fades. This distance will vary with the RF frequency. Typically a

"short path" is defined as any path length shorter than 5 miles at 5.8 GHz or 7 miles at 2.4 GHz. 2. Narrow Beam Antennas (high gain) This is the next most effective countermeasure. Narrow beam antennas ensure that the transmitted power is sent in a single direction and this minimizes the possibility of causing interference inadvertently to other users. Narrow beam antennas also reject off-azimuth signals being received from potential sources of interference and have high gain which boosts desired receive levels and improves the carrier to interference ratio. When selecting narrow beam antennas, it is helpful to know that larger antennas generally outperform smaller antennas. Another important antenna specification is the front-to-back ratio which ensures rejection of unwanted signals from azimuth angles behind the antenna. 3. Frequency Selection This is another very effective countermeasure. The LYNX.sc radio offers several distinct non-

overlapping frequency channel plans (see Sections 3.5 and 4.2) and the radios RF filter is able to reject interference more than 10 MHz away from the receive frequency. Offset frequencies combined with other countermeasures may enable several receive channels to operate at a single hub site. Because of the limited spreading ratio used, frequency selection is more efficient than code selection for interference rejection when operating multiple LYNX.sc terminals at a single site. Interference can often be overcome by exchanging frequencies of both-ends of the radio link (e.g. change your A1 terminal to an A2 and change the other end from an A2 to an A1). Also, changing channel plans (e.g. from A to B) can be very effective. (See Section 4.2). SECTION 4: TROUBLESHOOTING PAGE 4-19 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 4. Antenna Polarization Cross-polarized antennas can provide approximately 20 to 30 dB discrimination of unwanted signals. The actual discrimination will depend upon the antenna design and any rotation of polarization along the path, for example, due to reflections. Discrimination only exists between two orthogonal polarizations:

- vertical vs. horizontal or

- left-hand circular vs. right-hand circular There is only 3 dB discrimination between circular and linear (vertical or horizontal) polarization. Interference can sometimes be overcome by changing antenna polarization at both ends of the link. 5. Spreading Code Selection There are 4 selectable spreading codes provided for the LYNX.sc radio (See Section 3.12.3). These codes are selected by DIP switches and provide some discrimination against interference from other LYNX.sc transmitters. The discrimination is limited to approximately 3 to 6 dB for radios using the same channel plan. This is the difference between the co-channel C/I when using different codes for the wanted and unwanted signals. When combined with a different frequency channel, the code discrimination improves significantly beyond 3 to 6 dB. See Section 3.12.3 for code selection details. 6. Transmit Power The maximum level into the receiver is 0 dBm. Above this level, errors may occur in the receive data stream. Transmit output power should be reduced on very short paths to avoid overload. 7. Equipment/Antenna Location Occasionally, interference is caused by the radio or the antenna being too close to another similar transmitter. For example, at 2.4 GHz, microwave ovens can exhibit interference if mounted near the radio or antenna. Other high powered transmitters may also cause interference. Moving the radio, the antennas, or the interfering equipment can reduce or eliminate interference. the Interference countermeasures measurement of the received interference level and frequency. Prior to turning up a new hop, a spectrum analyzer can be used to monitor the spectrum at each end to check for possible interfering signals. See Section 4.8.1 for more details. to some extent on rely PAGE 4-20 SECTION 4: TROUBLESHOOTING INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 4.8.1 Use of a Spectrum Analyzer to Evaluate Potential Interference Connecting to the antenna and using "peak hold" on a spectrum analyzer, the spectrum between 2.4 GHz and 2.5 GHz (for 2.4 GHz radios) or 5.7 GHz and 5.9 GHz (for 5.8 GHz radios) can be swept and any signals being received at levels above the radios specified threshold identified. If potential interfering signals are found, then the LYNX.sc frequency plan can be changed to avoid a receive channel which may contain significant interference (see Section 4.2). For example, interference may be reduced by moving from the A1/A2 plan to the B1/B2 plan or by swapping terminals or RF filters so that A1 becomes A2. Signals outside the range of 2.4 GHz to 2.5 GHz (for 2.4 GHz radios) and 5.7 GHz to 5.9 GHz (for 5.8 GHz radios) may be ignored: they will not cause interference. If a spectrum analyzer is not available, the RSL voltage can be used to indicate the background noise and interference level within the receiver RF filter band when the far-end transmitter is turned off. With the far-end radio turned off, if an RSL voltage level above the radios threshold level is measured, there is potentially interference in this frequency channel. When using a spectrum analyzer for determining the presence of interference, very narrow resolution bandwidth settings must be used threshold

(approximately -87 to -95 dBm, depending on radio type). to detect signals down radios the to SECTION 4: TROUBLESHOOTING PAGE 4-21 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 4.9 Back-to-Back Testing Back-to-back testing, as shown in Figure 4-1, is an ideal method of testing the LYNX.sc radios. This testing eliminates link problems caused by auxiliary equipment, installation, or the radio path and isolates potential radio hardware problems. Back-to-back testing must be performed with both radios at the same location. The following test equipment is required:

v DC power source capable of supplying approximately 90 Watts (total) to the radios (or two AC adapters) v One low-loss coaxial cable, N-to-N male v One (or more) coaxial in-line calibrated fixed attenuators, 40 to 80 dB total attenuation The following test equipment may also be useful to perform further testing of the LYNX.sc radio:

v BER tester v Variable (60 dB range or more) RF attenuator (rated for the proper frequency, 2.4 or 5.8 GHz) v RF power meter Back-to-back testing must be performed to verify a radio problem before returning any radio to the factory for repair. When the equipment is connected as shown in Figure 4-1, without connecting the BER tester, both LYNX.sc radios should have no alarm conditions, except for DATA LOSS. When Loopback is enabled at either end, no errors should be registered by the ERROR indication. If these conditions have been met, then it is likely that the LYNX.sc radio is operating in accordance to specifications. If errors or alarms occur during this test, verify that all DIP switch settings are properly set. If alarms or errors are still present, the radio is likely to be faulty. If further troubleshooting is required for the radios themselves, a BER tester can be inserted into the rear panel bantam jacks (or the appropriate input/output data port) so an end-to-end or loopback test can be performed to assure that no errors are present in the radio link. In addition, a variable RF attenuator can be inserted between the radios to fade down the path to determine that the threshold specification is being met. The BER and threshold tests can be run in both directions to isolate the radio problem (if any). More information on BER testing is provided in Section 4.10. An RF power meter can be used to individually test each radios output power. PAGE 4-22 SECTION 4: TROUBLESHOOTING INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 LYNX.sc LYNX.sc Figure 4-1: Back-to-Back Test Configuration

(When using a BER tester, initiate loopback on connected LYNX.sc and select external test mode as described in Section 3.12.2). The LYNX.sc radios will be damaged if appropriate attenuation is not supplied between radios. You must provide a minimum of 40 dB and no more than 80 dB attenuation between the two radios. SECTION 4: TROUBLESHOOTING PAGE 4-23 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 4.10 BER (Bit Error Rate) Testing Bit error rate (BER) testing is the preferred way to evaluate a radio links performance. It can be performed from end-to-end or in loopback mode (which tests both directions of the radio path). Figure 4-2 illustrates a typical BER test configuration for loopback testing (which may include the radios path instead of in-line attenuators). Figure 4-2 illustrates a typical BER test configuration for end-to-end testing. When performing BER testing, make sure of the following:

- Disconnect all CEPT-1 inputs and outputs to both radios.

- Connect BER tester to bantam jacks or data in/output connector(s)

- Select external test signal for loopback testing using the DIP switches as defined in Section 3.12.

- Verify all DIP switch settings.

The BER test pattern chosen must contain adequate 1s density A 215-1, QRSS, or 3 The LYNX.sc uses HDB3 line coding. in 24 test pattern may be used. If two BER test sets are used to measure the link performance separately in each direction, frame slips will occur unless the BER test sets are synchronized with one test set as the master and the other as the slave. BER testing may be performed on the bench, with two terminals back to back, or over the radio path. Also, it may be performed from end-to-end (which requires two BER test sets over a link, the far-end unit slaved to the near-end units clock) or in loopback mode, as described in Section 4.9. If BER testing indicates an unacceptable level of errors, follow the instructions in Section 4.6.2. or perform a back-to-back test as described in Section 4.9. Figure 4-2: End-to-End BER Test Configuration PAGE 4-24 SECTION 4: TROUBLESHOOTING INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Your Notes on the LYNX.sc Radio SECTION 4: TROUBLESHOOTING PAGE 4-25 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 5. Appendices Appendix A - Digital Line Interface Specifications Information in Appendix A is referenced to the following document: ITU-T G.703 1. General Characteristics Bit rate:

Code:

2048 kbits/s 50 ppm HDB3 2. Specifications at the output ports Bit Rate 2.048 Mb/s Pulse Shape All marks of a valid signal must conform with the mask irrespective of the sign. The value V corresponds to the nominal peak value. Pair(s) in each Direction One Coaxial pair Test load impedance 75 ohms resistive Nominal peak voltage of a mark (pulse) Peak voltage of a space

(no pulse) 2.37 V 0 0.237 V Nominal pulse width 244 ns Ratio of the amplitudes of positive and negative pulses at the center of the pulse interval Ratio of the widths of positive and negative pulses at the nominal half amplitude 0.95 to 1.05 0.95 to 1.05 Table A-2: CEPT-1 Interconnection Specification SECTION 5: APPENDICES PAGE 5-1 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Nominal pulse V=100%

20%

10%

10%

20%

50%

269

(244 + 25) 194 ns

(244 50) 244 ns 219 0%

10%

10%

20%

10%

10%

488 ns

(244 + 244) CCITT-32540 Note V corresponds to the nominal peak Figure A-1: Mask of the E1 Pulse (CEPT-1) PAGE 5-2 SECTION 5: APPENDICES INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Appendix B - Rear Panel DIP Switches The LYNX.sc radio has two separate eight-segment rear panel DIP switches, labeled SW1, and SW3. Upon shipment from the factory, these switches are set for factory default configuration, which is all switches down (in the zero position), except for SW3 positions 5 through 8, which are set to match the installed rear panel RF filter assembly (which determines the frequency channel for transmit and receive, such as A1, A2, B1, B2, etc.). The tables in this section provide a quick reference for the DIP switch functions and their settings. DIP switch settings are noted by their position, either up (1), or down (0), not by on/off as may be printed on the DIP switch assembly. SECTION 5: APPENDICES PAGE 5-3 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Shaded switch positions are factory default SW1 1 0 SW2 SW3 1 0 1 0 1 0 1 0 1 1 0 1 0 1 1 0 1 0 0 1 1 2 x 2 0 1 2 0 3 0 4 0 5 0 6 0 7 0 Loss of Input Data Alarm Enable Disable

(depends on model) 3 0 1 Loopback Test Source Internal External Error LED Latch Enable Disable (Flash) 5 0 1 Rx AIS Output Enable Disable Diagnostics Port TBOS Craft 7 0 1 Aux Data Port Bridged (TBOS) Enabled (Clear) 4 0 1 4 0 3 0 CEPT-1 Ground Floating Grounded Note:

Not used on 2E/4E 2 0 2 0 1 0 1 3 x 4 x Spreading Code Code 1 Code 2 Code 3 Code 4 5 0 6 0 7 x x 3 0 1 4 0 1 Loss of Input Data Alarm Enable Disable

(depends on model) Frequency A1 A2 B1 B2 Xmtr 2410 2453 2430 2473 Rcvr 2453 2410 2473 2430 7 0 0 1 1 8 0 8 0 1 8 x x 8 0 1 0 1 Table B-1: LYNX.sc 2.4 GHz 1xE1, 2xE1 & 4XE1 Switch Settings PAGE 5-4 SECTION 5: APPENDICES INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Shaded switch positions are factory default SW1 1 0 SW2 SW3 1 0 1 0 1 0 1 0 1 1 0 1 0 1 1 0 1 0 0 1 1 2 0 2 0 1 2 0 2 0 1 2 0 2 0 1 0 1 3 0 4 0 5 0 6 0 7 0 Loss of Input Data Alarm Enable Disable 3 0 1 Loopback Test Source Internal External 4 0 1 4 0 3 0 CEPT-1 Ground Floating Grounded 3 0 4 0 Spreading Code Code 1 Code 2 Code 3 Code 4 Error LED Latch Enable Disable (Flash) 5 0 1 Rx AIS Output Enable Disable Diagnostics Port TBOS Craft 7 0 1 Aux Data Port Bridged (TBOS) Enabled (Clear) 5 0 6 0 7 0 Frequency A1 A2 Xmtr 2421 2462.5 Rcvr 2462.5 2421 8 0 8 0 1 8 x x 8 0 1 Table B-2: LYNX.sc 2.4 GHz 2xE1 Switch Settings SECTION 5: APPENDICES PAGE 5-5 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 S W 1 1 0 S W 2 1 0 S W 3 1 0 1 0 1 0 1 1 0 1 0 1 1 0 1 0 0 1 1 2 0 3 0 4 0 5 0 6 0 7 0 Loss of Input Data Alarm Enable Disable 3 0 1 Loopback Test Source Internal External 4 0 1 4 0 4 0 2 0 3 0 CEPT-1 Ground Floating Grounded 2 0 2 0 1 0 1 3 0 Spreading Code Code 1 Code 2 Code 3 Code 4 Frequency A 1 A 2 B 1 B 2 C 1 C 2 Xmtr 5735 5800 5755 5820 5775 5840 Error LED Latch Enable Disable (Flash) 5 0 1 Rx AIS Output Enable Disable Diagnostics Port T B O S Craft 7 0 1 Aux Data Port Bridged (TBOS) Enabled (Clear) 5 0 Rcvr 5800 5735 5820 5755 5840 5775 6 x x 6 0 0 0 0 1 1 7 x x 7 0 0 1 1 0 0 8 0 8 0 1 8 x x 8 0 1 0 1 0 1 Table B-3: LYNX.sc 5.8 GHz 1xE1 Switch Settings PAGE 5-6 SECTION 5: APPENDICES INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Shaded switch positions are factory default SW1 1 0 SW2 SW3 1 0 1 0 1 0 1 0 1 1 0 1 0 1 1 0 1 0 0 1 1 2 0 2 0 1 2 0 2 0 1 2 0 2 0 1 0 1 3 0 4 0 5 0 6 0 7 0 Loss of Input Data Alarm Enable Disable 3 0 1 Loopback Test Source Internal External Error LED Latch Enable Disable (Flash) 5 0 1 Rx AIS Output Enable Disable Diagnostics Port TBOS Craft 7 0 1 Aux Data Port Bridged (TBOS) Enabled (Clear) 4 0 1 4 0 3 0 CEPT-1 Ground Floating Grounded 3 0 4 0 Spreading Code Code 1 Code 2 Code 3 Code 4 5 0 6 0 Frequency A1 A2 B1 B2 Xmtr 5741 5803 5772 5834 Rcvr 5803 5741 5834 5772 7 x x 7 0 0 1 1 8 0 8 0 1 8 x x 8 0 1 0 1 Table B-4: LYNX.sc 5.8 GHz 2xE1 Switch Settings SECTION 5: APPENDICES PAGE 5-7 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Shaded switch positions are factory default SW1 1 0 SW2 SW3 1 0 1 0 1 0 1 0 1 1 0 1 0 1 1 0 1 0 0 1 1 2 0 2 0 1 2 0 2 0 1 2 0 2 0 1 0 1 3 0 4 0 5 0 6 0 Loss of Input Data Alarm Enable Disable 3 0 1 Loopback Test Source Internal External 4 0 1 4 0 4 0 1 4 0 4 0 1 Error LED Latch Enable Disable (Flash) 5 0 1 Rx AIS Output Enable Disable Diagnostics Port TBOS Craft Aux Data Port Bridged (TBOS) Enabled (Clear) CEPT-1 Ground Floating Grounded 5 0 6 x x Loss of Input Data Alarm Enable Disable Xmtr 5735 5800 5755 5820 5775 5840 Rcvr 5800 5735 5820 5755 5840 5775 6 0 0 0 0 1 1 3 0 3 0 1 3 0 Spreading Code Code 1 Code 2 Code 3 Code 4 3 0 1 Frequency A1 A2 B1 B2 C1 C2 7 0 7 0 1 7 x x 7 0 0 1 1 0 0 8 0 8 0 1 8 x x 8 0 1 0 1 0 1 Table B-5: LYNX.sc 5.8 GHz 4xE1 Switch Settings PAGE 5-8 SECTION 5: APPENDICES INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Appendix C - Rear Panel Data Connectors The following figures illustrate the pin structure for all rear panel data connections. All figures are oriented as a customer would view them, facing the rear panel. DC power connection information is found in Section 3.7 of the manual. Figure C-1: VF Port Connection Figure C-2: Alarm Port Connections SECTION 5: APPENDICES PAGE 5-9 INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Figure C-3: Diagnostic Port 9-Pin D-Style Connector Do NOT use both the RS-232 and RS-422 connections at the same time!

Figure C-4: AUX DATA Port 9-Pin D-Style Connector Do NOT use both the RS-232 and RS-422 connections at the same time!

PAGE 5-10 SECTION 5: APPENDICES INSTALLATION AND MAINTENANCE MANUAL LYNX.sc E1 FAMILY SPREAD SPECTRUM RADIOS SEPTEMBER 1999 Your Notes on the LYNX.sc Radio SECTION 5: APPENDICES PAGE 5-11 Index A AC................................................................................................................................................................................. 3-19 Accessories ................................................................................................................................................................. 2-22 AIS .......................................................................................................................... 2-7, 2-13, 2-20, 3-29, 3-30, 3-47, 4-13 Alarm connections...................................................................................................................................................... 3-46 Alarm interface ............................................................................................................................................................ 3-47 Alarms ....................................................................................................................................................................3-36, 4-7 Alignment, antenna .................................................................................................................................................... 3-23 Antenna...................................................................................................................... 2-3, 3-3, 3-24, 3-36, 3-39, 4-9, 4-19 Antenna connection................................................................................................................................................... 3-20 Antenna installation................................................................................................................................................... 3-22 Antenna planning....................................................................................................................................................... 3-10 Availability calculation ................................................................................................................................................ 3-7 B Balanced E1.................................................................................................................................................................. 2-18 Balun.............................................................................................................................................................2-7, 2-18, 3-25 Bit error rate ................................................................................................................................................................. 3-40 Bit Error Rate.......................................................................2-13, 2-14, 3-7, 3-30, 3-36, 3-41, 3-47, 4-9, 4-11, 4-17, 4-23 BNC............................................................................................................................................................................... 3-25 C Calculations ................................................................................................................................................................... 3-5 Caution ........................................................................................................................................................................... 1-2 CEPT-1.................................................................................................................................................. 2-18, 3-25, 5-1, 5-2 CEPT-1 connection..................................................................................................................3-36, 3-40, 3-47, 4-7, 4-17 Channel plan.......................................................................................................................................................3-12, 3-26 Coaxial cable ................................................................................................................................................................ 3-21 Code.............................................................................................................................................................................. 3-28 Coding ............................................................................................................................................................................ 2-2 Connections.............................................................................................2-7, 2-8, 2-15, 2-17, 2-18, 2-19, 3-25, 3-36, 5-1 Container........................................................................................................................................................................ 3-1 Controls ........................................................................................................................................................................ 2-14 CSU/DSU...................................................................................................................................................................... 3-30 D Data loss....................................................................................................................................................................... 3-29 DC...........................................................................................................................................................................3-9, 3-17 DIP switch.............................................................................................................................................................3-31, 5-3 DIP switch settings..................................................................................................................................................... 3-26 DIP switches ................................................................................................................................................................ 2-20 Dispersive fade.......................................................................................................................................................2-5, 3-6 E EIRP............................................................................................................................................................................... 3-32 Environment................................................................................................................................................................... 2-9 Error LED...................................................................................................................................................................... 3-42 Errors............................................................................................................................................................................. 4-17 F Fade margin.................................................................................................................................................................... 3-6 Fans............................................................................................................................................................................... 4-14 Frequency .............................................................................................................................................................3-12, 4-2 Frequency plan.............................................................................................................................................................. 3-8 Fresnel............................................................................................................................................................................ 3-4 Front panel................................................................................................................................................................... 2-11 G Grounding .................................................................................................................................................................... 3-17 H HDB3......................................................................................................................................................................4-23, 5-1 I Icons ............................................................................................................................................................................... 1-2 Installation ........................................................................................................................................... 1-1, 2-22, 3-3, 3-31 Interference.................................................................................................................................................................. 4-18 ISO 9000...............................................................................................................................................................................i L Line-of-sight .................................................................................................................................................................. 3-4 Link budget.................................................................................................................................................................... 3-5 Loopback..........................................................................................................................2-7, 2-14, 3-27, 3-40, 4-10, 4-17 M Mechanical................................................................................................................................................................... 2-10 MHS.............................................................................................................................................................................. 3-56 Mounting ..................................................................................................................................................................... 3-15 N Note................................................................................................................................................................................. 1-2 O Orderwire .......................................................................................................2-8, 2-19, 2-21, 3-31, 3-36, 3-43, 3-44, 3-45 Output power......................................................................................................................................................3-33, 3-34 Output power, adjust................................................................................................................................3-37, 3-38, 3-39 P Path ................................................................................................................................................................................. 3-4 Path planning............................................................................................................................................................... 3-10 Power...................................................................................................................2-2, 2-9, 2-22, 3-3, 3-16, 3-39, 4-9, 4-19 Power connection ....................................................................................................................................................... 3-16 Power connection, AC............................................................................................................................................... 3-19 Power connection, DC................................................................................................................................................ 3-17 Power supply planning ................................................................................................................................................ 3-9 Professional installation.......................................................................................................................................... iii, 1-1 R Rear panel..............................................................................................................................................................2-16, 5-9 Receive signal level.............................................................2-12, 2-14, 3-3, 3-5, 3-22, 3-23, 3-24, 3-35, 3-47, 4-9, 4-20 Receiver.......................................................................................................................................................................... 2-4 Regulatory............................................................................................................................................................... iii, 2-10 REN ............................................................................................................................................................................... 3-43 Repair.............................................................................................................................................................................. 4-5 Repeater configurations....................................................................................................................................3-54, 3-55 RF filter......................................................................................................................................................................... 3-26 RS-232/RS-422 ........................................................................................................................2-19, 3-48, 3-49, 3-50, 3-53 RSL................................................................................................................................................................................ 3-24 S SD Configuration ........................................................................................................................................................ 3-57 Shipping ................................................................................................................................................................2-22, 3-1 Spares ............................................................................................................................................................................. 4-3 Spreading code............................................................................................................................................................ 3-28 Switches ......................................................................................................................................................................... 4-2 Synchronization .......................................................................................................................................................... 4-12 System.....................................................................................................................................................................2-5, 2-6 T TBOS...................................................................................................2-19, 2-20, 2-21, 3-43, 3-48, 3-51, 3-52, 3-53, 3-54 Technical support ......................................................................................................................................................... 4-4 Telephone .................................................................................................................................................................... 3-43 Test ........................................................................................................................................................................2-8, 2-12 Tips ................................................................................................................................................................................. 1-2 Tools ............................................................................................................................................................................. 3-11 Transmission line........................................................................................................................................................ 3-21 Transmitter............................................................................................................................................................2-2, 3-37 Troubleshooting ........................................................................................................................................................... 4-1 Turn-up......................................................................................................................................................................... 3-31 W Warranty ........................................................................................................................................................................... v For ISO Purposes -

Last Page of this Manual

 

 

1196 Borregas Ave., Sunnyvale, CA 94089-1302, USA Fax: +1 (408) 542-5300 Tel: +1 (408) 542-5200, Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 February 18, 2000 Attention:

Reviewing Engineer RE:

Product Installation and Maintenance Manual Update for HZB-S24-04 After the application for HZB-S24-04 was submitted to FCC, we updated our product manual to comply with FCC requirements raised while a previous application was in review. Since our LYNX.sc Installation and Maintenance manual covers the whole spread spectrum LYNX.sc product line, these changes applies to the product manual submitted for this application as well. Please find in the attached an updated page of page 3-22 for section 3.10. Please use this page to replace the same page of the submitted manual. Yours truly, Caroline Yu International Product Manager Western Multiplex Corporation

 

 

WESTERN 1196 Borregas Avenue Sunnyvale, CA 94089 USA Multiplex tel 408 542 5200 fax 408 542 5300 www. Wirelessintercennect.com January 24, 2000 Federal] Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attention: Reviewing Engineer The users manual supplied in this application is written to include several models of the LYNX.sc El product. The unit being submitted here is the 2.4 GHz, 2xE! radio (Model 3 1360). As certifications are obtained, the appropriate regulatory information in the manual is edited. When this manual is released for customers, an appropriate statement will be made in the regulatory information cover sheet indicating which models comply with which FCC and IC rule parts and their appropriate certification numbers provided in of the manual. If you have any questions regarding this submission, please feel free to contact the undersigned.

Caroline Yu International Product Manager Wireless Interconnect Everywhere