Qixiang Electron Science & Technology Co.,Ltd. www.anytone.net A 1
. 0 AT-5100 10 METER AMATEUR RADIO Operating Instructions CONTENTS 1. FUNCTIONS & FEATURES ..............................................................1 2. STANDARD ACCESSORIES ............................................................2 3. INSTALLATION .................................................................................2 4. GETTING ACQUAINTED ..................................................................5 5. HOW TO USE YOUR RADIO ...........................................................8 6. BACKGROUND FUNCTION / MAIN MENU OPERATION .............11 7. PUBLIC MENU OPERATION .........................................................14 8. CHANNEL MENU OPERATION .....................................................14 9. BT MENU OPERATION(OPTIONAL) .............................................16 10. SPECIFICATIONS .........................................................................17 11. CTCSS/DCS CHART ....................................................................18 1. FUNCTIONS & FEATURES Large LCD display with backlight dimming FM / AM / USB / LSB / CW / PA modes Frequency Tuning Step:
10Hz / 100Hz / 1KHz / 5KHz / 10KHz / 100KHz / 1MHz 500Hz/5KHz CLARIFIER Adjustment (R/T/R+T selectable) Flexible Menu Functions and PC CPS Software option TX and RX Noise Reduction VFO / BAND / Memory Channel modes CTCSS/DCS with RX/TX Split functions VOX Function SQ, ASQ Function (FM and AM mode only) RF GAIN Adjustment RF PWR Adjustment SCAN Function NB/ANL Function Repeater Shift / Offset Frequency Function SIG / PWR / SWR Meter Functions TOT Function HI-CUT Function SWR Protection Power Supply Voltage Protection Key-Lock Function Band Name Customization Function (via PC CPS) Compatible with electret and dynamic MIC types ECHO Function Programmable RB Function Keypad Beep Function
+10KHZ Function DW Dual-Watch Function EMG Channel Function 1 2. STANDARD ACCESSORIES Radio Microphone Mounting Bracket Microphone Hanger Non-slip Mat Pads for bracket Adjusting screws Spare Fuses
(10A, 125V) Self-tapping Screws ower cord 3. INSTALLATION Choose the most appropriate location from a simple and practical point of view. If installed in a vehicle, care should be taken to ensure your radio does not obstruct the driver or passengers. 1. Use the Self-tapping Screws and Pads to fix the Bracket to a suitable location. 2. Attach the Adhesive Case Protectors to the inside ends of the Mounting Bracket and insert the Radio. Fit the Adjusting Screws loosely, and choose a suitable angle by moving the Adjusting Screws to one of the 3 positions on the Mounting Bracket. 3. Tighten the Adjusting Screws firmly by hand. Make sure the radio and all accessories are securely mounted. 3.1 Microphone Connection 1. Insert the microphone connector into the microphone jack. 2. The microphone connector will "click" into place. 2 3.2 Antenna Installation Before using this radio, please install an efficient and resonant antenna. Using an antenna that is correctly installed and tuned will enable excellent communication performance. This radio requires an antenna impedance of 50 ohms, unbalanced. 1. Screw the antenna connector into the antenna jack. 2. Grounding the antenna system to ensure best performance of this radio. WARNING:
NEVER transmit without a connected resonant antenna, or a suitable 50 ohm load being connected. Damage to the radio may result. To reduce the risk of electric shock, or radio damage, base station installations should include lightning protection devices. Ask your Anytone dealer for available antenna options. 3. A mobile antenna can be mounted in various locations, for example:
3.3 Power Connection This radio requires a 13.2V (12V) DC power supply. Never connect the radio directly to a 24V DC battery system, as can be found in some vehicles. Please refer to the radio Specifications to ensure your 13.2V DC power supply can provide enough current
(amps), otherwise poor performance may occur. 1. Connect the positive (red) power cable to the + terminal of the battery. 2. Connect the negative (black) power cable to the - terminal of the battery. 3. Connect the DC power cable to the transceiver's power supply connector. Locate the power cable away from high temperature, moisture, and other electrical systems. Ensure it is installed where it cannot be damaged. It is not recommended to use a vehicle cigar/cigarette lighter socket to power the radio, as it may not supply the correct voltage or current. Do not remove the fuse holder from the cable.
+ (Red wire) 12V 3
- (Black wire) connected to chassis ground in most 12V vehicles (confirm with your vehicle manufacturer) 3.4 Replacing Fuses This radio requires a 10A, 250V fuse. If the fuse blows, determine the reason, then correct the problem. After the problem is resolved, replace the fuse. If newly installed fuses continue to blow, disconnect the power cable and contact your authorized dealer or an authorized service center:
1. Twist the two fuse covers in opposite directions, and open it. IN-LINE FUSE HOLDER
, 10A 250V FUSE 2. Replace the blown fuse with new one, and close the fuse holder. 3. Be sure to only use the correct fuse type, otherwise damage may occur. IN-LINE FUSE HOLDER IN-LINE FUSE HOLDER FUSE IN-LINE FUSE HOLDER 3.5 Install Microphone Hanger Choose a location which will not interfere with the driver. Use the supplied self-tapping screws and pads to install the hanger. 3.6 Install External Speaker (Optional) If using an external speaker, please choose an 8 ohm speaker with a 3.5mm mono
(double cable) TS type plug. 1. Install the external speaker in a suitable place. 2. Plug into the speaker jack. 4 4. GETTING ACQUAINTED 4.1 Front Panel 3 4 No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 2 RB BP COR DIM DW L-OFF SCAN S.LIST 5 6 NB ANL EMG LOCK
+10K HCUT MEM STOR 7 8 14 9 10 11 12 13 Key Echo RB/BP Functions Roger beep, Key beep and Echo on/off control CTC/DCS COR.DIM CTCSS/DCS control Backlight color and Dimmer control DW/L-OFF Dual watch and LCD off control SCAN SLIST NRC NB/ANL Turn on/off scan, or add/delete scan channel NRC function on/off control NB/ANL on/off control VOX EMG/LOCK VOX on/off control Emergency channel and key lock on/off control
+10K HICUT MEM STOR
+10KHz on/off control Hi-Cut on/off control MEM channel control Memory channel add/delete VOL/OFF SQ External knob: Volume control, Power on/off radio Internal knob: ASQ/SQ control RFG PWR CH.F MODE BAND External knob: RF gain control Internal knob: Power level control Channel / frequency control knob Working mode AM/FM/USB/LSB/PA/CW control Working band control CLA SSB Clarifer Control Type C jack for programming (Special cable required ) 5 4.2 Rear Panel 15 16 17 18 No. Functions 15 Antenna Jack 16 17 18 CW Jack External SP Jack Power Supply Jack 4.3 Microphone DOWN PTT 4-Pin Connector PF (User defined) UP MIC 1. MIC (White wire) 2. PTT (Blue) 3. Key(Red wire) 4. GND (Winding wire) Microphone cable 6 4.4 LCD Display 4 5 6 7 9 11 10 12 13 8 1 2 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 14 15 16 17 18 19 20 22 21 24 23 25 26 27 28 29 30 31 SWR indicator TX Signal strength indicator RX Signal strength indicator Transmit indicator Working band indicator Working chanel indicator Displays the modulation mode Appears when Noise Reduction function is ON Appears when using ASQ Appears when ANL function is ON Appears when VOX function is ON Appears when Noise Blanker is ON Appears when Scan function is ON Appears when Echo function is ON Appears when Hi-Cut function is ON Display of frequency Appears when the Keypad lock function is ON Appears when MENU key is short-pressed Appears when Beep is ON Appears when RB function is ON Appears when CTCSS is enabled BT function indicator(Optional) CTCSS/DCS code Appears when DCS is enabled Appears when using Emergency channel Appears when enter memory mode Appears when enter frequency band setting Clarifier setting, 1: RX, 2: TX. 3: TX+RX Appears when the channel is excluded from the Scan List Appears when the +10KHz function is ON Appears when Dual-watch function is ON 7 5. HOW TO USE YOUR RADIO 5.1 Power OFF/ON 1. Turn VOL clockwise to switch the radio ON. (The radio may emit a beep if the KEY.BEEP function is enabled in the Main Menu). The LCD display will show a frequency or a channel number. 2. Turn VOL control fully anti-clockwise to switch the radio OFF. 5.2 Volume Control When the radio is turned on, turning VOL clockwise will increase the Volume level. Turning VOL anti-clockwise will reduce the Volume level. Adjust the volume during communication to achieve a suitable level. 5.3 Squelch Control When the radio is receiving, turn SQ knob clockwise to adjust the Squelch level. Turn SQ switch anti-clockwise to the end position to enable ASQ function. NOTE: ASQ can be enabled or disabled from the Main Menu. 5.4 RF Gain Control When the radio is receiving, turn RFG control to adjust the RF Gain. Turn the control clockwise to increase RF Gain, and anti-clockwise to reduce RF Gain. 5.5 RF Power Control Valid for AM/FM/LSB/USB/CW modes. Turn PWR control to adjust the TX Output Power. Turn the control clockwise to increase Power, and anti-clockwise to reduce Power. 5.6 Channel Selection When the radio is in Channel Mode, turn channel knob to select desired channel. Turn clockwise to increase the channel number, and anti-clockwise to reduce the channel number. 5.7 VFO Mode (uF) Frequency Control Push CH.F knob, LCD displays
, then push MODE knob to enter VFO Mode. Turn CH.F knob to adjust frequency. Push CLA knob to toggle the "quick" frequency step. NOTE: The default STEP size is set in the Main Menu (long press PF key for shortcut). 5.8 Mode Control Turn MODE knob to change the working mode FM-AM-USB-LSB-PA-CW. NOTE: Modes can be disabled using the PC CPS Programming Software (optional). 8 5.9 Band Control Push MODE knob, the LCD displays Push MODE knob again to exit. 5.10 SSB Clarifier Control
, then turn MODE knob to change band. When the radio is transmitting or receiving, turn CLAR knob to adjust USB/LSB/CW TX or RX frequency. Turn it clockwise to increase frequency, and anti-clockwise to reduce frequency. 5.11 RB/BP/ECHO Press Push CH.F knob, the LCD displays to turn on/off Roger beep, LCD displays "
, then press
" when turn on RB function. key to turn on/off key beep. The LCD displays "
Hold and press on Echo function.
" when turn on key beep function. key to turn on/off Echo function, the LCD displays when turn 5.12 COR/DIM/CTC/DCS Press to change backlight color. Push CH.F knob, the LCD displays
, then press key to change dimmer level. Press and hold key to turn on/off CTCSS/DCS function, the LCD displays or when turn on CTCSS/DCS function. 5.13 DW/L-OFF to turn on/off dual watch function, the LCD displays Press Push CH.F knob, the LCD displays
. key to turn on/off LCD.
, then press When the LCD is off, push [CH/F] knob and then press key to turn LCD on. 5.14 SCAN/S.LIST to turn on/off scan function, the LCD displays Press Push CH.F knob, the LCD displays scan list. Repeat this operation to remove current channel from scan list.
, then press
. key to add current channel to 5.15 NB/ANL/NRC Press Push CH.F knob, the LCD displays to turn on/off NB function, LCD displays
, then press when turn on NB. key to turn on/off ANL. The LCD displays Hold and press on NRC function. when turn on ANL. key to turn on/off NRC fuction, the LCD displays when turn 9 5.16 EMG/LOCK/VOX Press channel, the LCD displays "
Push CH.F knob, the LCD displays to enter CH9, repeat press to enter CH19, third press returns to normal
" when enter CH9 or CH19.
, then press key to turn on/off Key Lock. The LCD displays "
Hold and press The LCD displays
" when turn on the Key Lock function. key to turn on/off VOX function. when turn on VOX function. 5.17 +10K/HCUT to turn on/off +10Khz function, the LCD displays
. Press Push CH.F knob, the LCD displays
, then press key to turn on/off HICUT. The LCD displays when turn on HI-CUT function. 5.18 MEM/STOR to enter Memory channel mode, the LCD displays "
Press NOTE: If no Memory channel is stored, the radio will not respond.
". To store or delete a Memory channel:
Choose a channel from channel mode, press and hold to enter memory channel store status, the channel number behind MEM -- falshes, turn CH knob to choose key to store it. In memory channel the memory channel number, hold and press for over 3 seconds to delete current mode, choose a channel , hold and press memory channel. 10 6. BACKGROUND FUNCTION / MAIN MENU OPERATION 1. Push and hold CH knob to enter the Main Menu function list;
2. Turn the CH knob or press microphone UP/DN key to select the required Menu item;
3. Push CH knob to enter menu value setup;
4. Turn the CH Channel switch to select wanted setting;
Push CH to return to last menu item. 5. Press any other key or wait 5 seconds, the setting will be stored. No. LCD Display Values and Descriptions 1 2 3 4 5 6 7 8 9 10 11 KEY.BEEP ON: Turn on key beep OFF: Turn off key beep Default: ON INDIC STEP OFF: Displays TX frequency when in TX;
SWR: Displays SWR value when in TX;
TOT: Displays TOT remaining time when in TX;
DC: Displays DC voltage when in TX;
Default: OFF Adjust the default step size in VFO mode. Options: 10Hz, 100Hz, 1KHz, 5KHz, 10KHz, 100KHz, 1MHz;
Default: 1KHz. MIC.GAIN 1-45, Total 45 levels of Microphone Gain available. Default: 35 MIC.TYPE ELCE: Electret Microphone DYNA: Dynamic Microphone Default: ELEC NOG.SET 1-32, OFF, Total 33 levels available;
Default: OFF (Disable NOG function) ECHO-L ECHO-T TOT.SET TX.SWR TDC.SET 1-32, Total 32 levels available;
Default: 28 1-32, Total 32 levels available;
Default: 28 1-600s, OFF, Total of 10 minutes available;
Default: 180s OFF: Disable the SWR Protection function;
ON: Enable the SWR Protection function;
Default: ON OFF: Disable the Voltage Protection function;
ON: Enable the Voltage Protection function;
Default: ON 11 No. LCD Display Values and Descriptions 12 SCN.TYPE SQ: Squelch based scan function;
TI: Time based scan function;
Default: SQ 13 CLA.SET OFF: Disable clarifier adjustment R: Enable RX frequency adjustment;
T: Enable TX frequency adjustment;
RT: Enable both RX and TX frequency adjustment;
Default: R 14 15 16 17 18 19 20 21 22 23 24 25 26 27 CLA.FRQ 500Hz: adjustable range 500Hz;
5KHz: adjustable range 5KHz;
Default: 500Hz DIM.SET 1-9, 9 backlight dimmer levels available;
Default: 9 COLOR DW.SET EMG.CH1 EMG.CH2 TX.REP ASQ VOX VOX-L VOX-T RX NR TX NR WHITE, BLUE, GREEN, YELLOW, RED, PURPLE, CYAN, OFF Default: WHITE Set the Dual Watch channel, mode and band Set Emergency Channel 1 and its mode Set Emergency Channel 2 and its mode 100Hz-5MHz, Frequency Shift/Offset range. Default: 100KHz OFF: Turn off ASQ function;
ON: Turn on ASQ function;
Default: ON OFF: Turn off VOX function;
ON: Turn on VOX function;
Default: OFF 01-09, Total of 9 VOX sensitivity levels Default: 03 01-09, Total of 9 VOX Delay Time levels;
Default: 04 01-05: Total of 5 levels for RX noise reduction;
Default: 03 01-05: Total of 5 levels for TX noise reduction;
Default: 03 FM.DEB 2K: 2KHz FM deviation 4K: 4KHz FM deviation Default: 2K 12 No. LCD Display Values and Descriptions 28 TONE HI-4K: 4K audio response;
LO-3K: 3K audio response;
Default: HI-4K 29 CW.BEEP 30 CW.FREQ 01-63: Adjusts the CW Sidetone level (volume);
OFF: CW Sidetone disabled;
Default: 31 300Hz-3KHz: This menu is to select CW Sidetone frequency. The frequency step is 10Hz;
Default: 1050Hz 31 CW.RX Setting CW-U: select USB for CW RX;
CW-L: select LSB for CW RX;
Default: CW-U 32 CW.BKIN 10-1000MS: TX delay (CW break-in);
OFF: No TX delay;
Default: 500MS 33 CW.SHIF ON: CW RX Shift ON (RX Shift = +/- "CW.FREQ");
OFF: CW RX Shift OFF;
Default: OFF 34 AGC.SET SLOW: AGC SLOW response;
FAST: AGC FAST response;
Default: SLOW 35 36 37 PF.KEY TX.DRC Customize menu settings for the microphone, press the PUSH key to enter and select the desired function;
Default: VOX function OFF: Turn off Dynamic Range Compression TX function;
ON: Turn on Dynamic Range Compression TX function;
Default: ON Factory Reset MENU: Settings/Functions reset to defaults;
ALL: Channels and Settings/Functions reset to defaults;
Default: ALL 13 7. PUBLIC MENU OPERATION 1. Push and Hold the MODE knob to enter Public menu list;
2. Turn the CH knob or press microphone UP/DN key to select the required Menu item;
3. Push CH knob to enter menu value setup;
4. Turn the CH Channel switch to select wanted setting;
Push CH to return to last menu item. 5. Press any other key or wait 5 seconds, the setting will be stored. No. LCD Display Values and Descriptions 1 2 3 4 5 6 HI-CUT OFF: Disable HI-CUT function;
ON: Enable HI-CUT function;
Default: OFF. NB ANL ECHO 10KHz OFF: Disable NB function;
NB: Enable NB function;
Default: OFF OFF: Disable ANL function;
NB: Enable ANL function;
Default: OFF OFF: Disable ECHO function;
ON: Enable ECHO function;
Default: OFF OFF: Disable +10KHz function;
ON: Enable +10KHz function;
Default: OFF Roger Beep OFF- 5, Total 6 options. Default: OFF, (RB Disabled) 8. CHANNEL MENU OPERATION 1. Push CH knob and then push and hold the MODE knob to enter Channel menu list;
2. Turn the CH knob or press microphone UP/DN key to select the required Menu item;
3. Push CH knob to enter menu value setup;
4. Turn the CH Channel switch to select wanted setting;
Push CH to return to last menu item. 5. Press any other key or wait 5 seconds, the setting will be stored. 14 No. LCD Display Values and Descriptions 1 2 3 4 5 6 7 BUSY REP R-CDC T-CDC RT-CDC SCAN PUBLIC OFF: Disable Busy Channel Lockout function;
ON: Enable Busy Channel Lockout function;
Default: OFF RPE+: Enable offset + direction function, TX frequency > RX frequency;
REP-: Enable offset - direction function, TX frequency < RX frequency;
OFF: Disable offset direction function. Default: OFF CTCSS/DCS: RX setup OFF: Turn off CTCSS/DCS function;
CTCSS: 67.0Hz~250.3Hz, Total 38 tones;
DCS: D023N~D754N, Total 104 codes;
Default: OFF CTCSS/DCS: TX setup OFF: Turn off CTCSS/DCS function;
CTCSS: 67.0Hz~250.3Hz, Total 38 tones;
DCS: D023N~D754N, Total 104 codes;
Default: OFF CTCSS/DCS: RX+TX setup OFF: Turn off CTCSS/DCS function;
CTCSS: 67.0Hz~250.3Hz, Total 38 tones;
DCS: D023N~D754N, Total 104 codes;
Default: OFF ADD: When the second decimal point on the LCD display does not show, it indicates that the current channel has been added to the scan list. DEL: When the second decimal point appears on the LCD display, it indicates that the current channel has LCD display Value and description been added to the scan list. Default: ADD OFF: Choose independent channel menu;
ON: Choose public channel menu;
Default: ON NOTE: When OFF is selected, additional hidden Public channel menu items will appear, allowing channels to be individually configured with individual settings. 15 9. BT MENU OPERATION(OPTIONAL) 1. Hold and push CLA knob to enter the BT menu list;
2. Turn the CH knob or press microphone UP/DN key to select the required Menu item;
3. Push CH knob to enter menu value setup;
4. Turn the CH Channel switch to select wanted setting;
Push CH to return to last menu item. 5. Press any other key or wait 5 seconds, the setting will be stored. No. LCD Display Values and Descriptions 1 2 3 4 5 6 7 8 9 10 11 BT.CON OFF: Turn off BT wireless function;
ON: Enable BT wireless function;
Default: OFF BT.PAIR CONNECT: Pair BT device DISC: Disconnect BT device HOLD-TIM BT wireless hold time setting, this product has OFF, 1S~120S, and infinity options to choose from. BT.DELY BT wireless delay time setting, this product has 30ms, 1s~5.5s to choose from. BT +INT BT.MIC BT.SPK PTT.PAIR Local speaker switch settings in BT wireless mode OFF: Turn off the local speaker;
ON: Turn on the local speaker;
Default: OFF BT wireless MIC gain adjustment, this product has 1-5 levels to choose from BT wireless earphone gain adjustment, this product has 1-5 levels to choose from. BT wireless PTT pairing menu, this product supports BP- 02 BT wireless PTT Connect PTT: BT wireless PTT pairing Disconnect PTT: Disconnect BT wireless PTT pairing PTT.HOLD BT wireless PTT hold settings OFF: Turn off BT wireless PTT hold;
ON: Enable BT wireless PTT hold;
Default: OFF PTT.SLEEP BT wireless PTT sleep setting, this product has infinity and 1min-4min options to choose from. PTT.BAT BT wireless PTT battery level query, displaying the current BT wireless PTT battery level. 16 10. SPECIFICATIONS Modulation Mode Frequency Range Frequency Band Channel Frequency Control Frequency Step Microphone Frequency Tolerance Input Voltage Dimensions(in mm) Weight Operating Temperature Range Antenna Connector Power Output Drain Inter-modulation Distortion SSB Carrier Suppression Unwanted Sideband Frequency Response Modulated signal distortion Output Impedance Sensitivity Selectivity Image Rejection Adjacent Channel Rejection IF Frequencies RF Gain Control Automatic Gain Control(AGC) GENERAL AM/FM/USB/LSB 28.000-29.700MHz A/B/C/D/E/F/G/H/I + VFO 40 channels (programmable) in each band Phase-Locked-Loop Synthesizer 10Hz,100Hz,1KHz,5KHz,10KHz,100KHz,1MHz With Push-to-Talk / UP / DN / PF and coiled cord 5.0ppm 12V 187(L)x175(W)x53(H) about 1.0kg
-20 C TO + 50 C UHF,SO-239 TRANSMITTER AM=10W(PEP=35W),FM=30W,SSB=30W(PEP) 10A (with modulation) SSB: 3rd order, more than -25dB;
5th order, more than -35dB 55dB 50dB AM/FM: 300 to 3000Hz SSB: 450 to 2500Hz inferior to 5%
50 ohms RECEIVER AM:1.0V for 10dB(S+N)/N at greater than 1/2 watt of audio output. FM: 1.0V for 20dB (S+N)/N at greater than 1/2 watt of audio output. SSB: 0.25V for 10dB(S+N)/N at greater than 1/2 watt of audio output. AM/FM:6dB@3kHz,50dB @9kHz SSB: 6 [email protected],60dB @3.3kHz 65dB 60dB AM/FM: 10.695MHz 1st IF, 455 KHz 2nd IF SSB: 10.695MHz 45dB adjustable for optimum signal reception Less than 10dB change in audio output for inputs from 10V to 100,000V 17 11. CTCSS/DCS CHART 10.1 38 SETS ANALOG FRQ LIST(CTCSS) No. 01 02 03 04 05 06 07 08 09 10 Freq.(Hz) 67.0 71.9 74.4 77.0 79.7 82.5 85.4 88.5 91.5 94.8 No. 11 12 13 14 15 16 17 18 19 20 Freq.(Hz) 97.4 100.0 103.5 107.2 110.9 114.8 118.8 123.0 127.3 131.8 No. 21 22 23 24 25 26 27 28 29 30 Freq.(Hz) 136.5 141.3 146.2 151.4 156.7 162.2 167.9 173.8 179.9 186.2 No. 31 32 33 34 35 36 37 38 Freq.(Hz) 192.8 203.5 210.7 218.1 225.7 233.6 241.8 250.3 10.2 104 SETS DIGITAL FRQ LIST(DCS) Code No. 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 DSC
(Octal) 023 025 026 031 032 036 043 047 051 053 054 065 071 072 073 074 114 115 116 122 125 131 132 134 143 145 Code No. 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 DSC
(Octal) 152 155 156 162 165 172 174 205 212 223 225 226 243 244 245 246 251 252 255 261 263 265 266 271 274 306 Code No. 053 054 055 056 057 058 059 060 061 062 063 064 065 066 067 068 069 070 071 072 073 074 075 076 077 078 18 DSC
(Octal) 311 315 325 331 332 343 346 351 356 364 365 371 411 412 413 423 431 432 445 446 452 454 455 462 464 465 Code No. 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 104 DSC
(Octal) 466 503 506 516 523 526 532 546 565 606 612 624 627 631 632 654 662 664 703 712 723 731 732 734 743 754 EU Declaration of Conformity In accordance with EU Directives and Regulations Qixiang Electron Science & Technology Co., Ltd ADD: Qixiang Building, Tangxi Industrial Zone, Luojiang, Quanzhou, Fujian, 362011 China as the manufacturer, hereby declares under our sole responsibility that product(s): 10 Meter Amatuer Radio Model name: AT-5100 is in conformity with the essential requirements of the Radio Equipment Directive 2014/53/EU:
Radio Article 3.2 ETSI EN 301 783 V2.1.1 (2020-06) ETSI EN 300 328 V2.2.2 (2019-07) EMC Article 3.1(b) Safety Article 3.1(a) ETSI EN 301 489-1 V2.2.3 (2019-11) ETSI EN 301 489-15 V2.2.1 (2019-04) ETSI EN 301 489-17 V3.3.1 (2024-09) EN IEC 62368-1:2024+A11:2024 Health Article 3.1(a) EN 50566 :2017 EN IEC 62311:2020 Signed on behalf of Qixiang Electron Science & Technology Co., Ltd
(Signature of authorized person) Name: Ken Xu Title: Manager Date: 2026-07-30 WARNING STATEMENT Use the 10M Amateur to 50, otherwise, it may damage your 10M Amateur Radio. Radio in the environment with the temperature between -20 It can be operating under 2000m. The full text of the EU declaration of conformity is available at the following internet address: www.xxxyyy.com Hereby, We, declare that the radio equipment type 10M Amateur Radio is compliance with Directive 2014/53/EU. RF Exposure Warning Statements:
This equipment complies radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 164 cm between the radiator & body. External Antenna:
Antenna Gain: 0dbi (Typical), 3.0dBi (Max) Antenna Impedance:50 Ohms BT Antenna Gain: 3.24dBi MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW WARNING STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference including received interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning Statement This radio transmitter has been approved by lndustry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. External Antenna:
Maximum Antenna Gain: 3.0 dBi & BT Ant 3.24dBi Antenna lmpedance: 50 Ohms RF Exposure Statement This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 164 cm between the radiator
& your body. EU Declaration of Conformity In accordance with EU Directives and Regulations Qixiang Electron Science & Technology Co., Ltd ADD: Qixiang Building, Tangxi Industrial Zone, Luojiang, Quanzhou, Fujian, 362011 China as the manufacturer, hereby declares under our sole responsibility that is in conformity with the essential requirements of the Radio Equipment Directive 2014/53/EU:
product(s): 10 Meter Amatuer Radio Model name: AT-5100 Radio Article 3.2 ETSI EN 301 783 V2.1.1 (2016-01) EMC ETSI EN 301 489-1 V2.2.3 (2019-11) Article 3.1(b) ETSI EN 301 489-15 V2.2.1 (2019-04) Safety EN IEC 62368-1:2024+A11:2024 Article 3.1(a) Health Article 3.1(a) EN IEC 62311:2020 Signed on behalf of Qixiang Electron Science & Technology Co., Ltd
(Signature of authorized person) Name: Ken Xu Title: Manager Date: 2026-07-30 ATTENTION: conditions of use!
The band of frequencies on which this device operates is administrated by limitations and/or permissions for their usage. Consequently, in the EU countries mentioned in the sheet, operators must consult the entrusted authorities. In particular, they must possess a license or a frequency assigned to them by their respective competent authority. ACHTUNG: informativ zur Benutzung!
Das Frequenzband, auf dem dieses Gert arbeitet, wird durch Einschrnkungen und/oder Berechtigungen fr deren Verwendung verwaltet. Folglich mssen die Betreiber in den in der Tabelle aufgefhrten EU-Lndern die zustndigen Behrden konsultieren. Insbesondere mssen sie ber eine Lizenz verfgen, oder eine Frequenz besitzen, die ihnen von ihrer jeweiligen zustndigen Behrde zugewiesen wurde. ATTENTION : conditions dutilisation!
Certaines bandes de frquence sur lesquelles cet appareil fonctionne sont rgies par des limitations et/ou il faut des autorisations pour les utiliser. Par consquent, dans les pays de lUE indiqus dans le tableau, les oprateurs doivent dabord consulter les autorits appropries. Les oprateurs utilisant cet appareil doivent donc possder une licence ou une frquence qui leur est attribue par les autorits comptentes. ATENCIN: informacin sobre el uso!
La banda de frecuencias en la que opera este aparato est gestionada por limitaciones y/o permisos para su uso. Por lo tanto, en los pases de la UE que se muestran en la tabla, los operadores deben consultar a las autoridades correspondientes. En particular, deben poseer una licencia o una frecuencia asignada por su respectiva autoridad competente. ATTENZIONE: informativa alluso!
La banda delle frequenze sulle quali opera questo apparato amministrata da limitazioni e/o permessi al loro uso. Quindi, nei paesi UE riportati nella tabella, gli operatori devono consultare le autorit preposte. Segnatamente, devono possedere una licenza oppure una frequenza assegnata a loro dalla rispettiva autorit competente. Qixiang Electron Science & Technology Co., Ltd. Add: Qixiang Building, Tangxi Industrial Zone, Luojiang District, Quanzhou 362011, Fujian, China
