FCC ID: T4KAT5888UVIII LAND MOBILE RADIO

5888UV III TRI-BAND FM TRANSCEIVER USER'S MANUAL Nice Housing, Stoutness & Stability, Advanced and Reliable functions, Perfect & Valuable. Approval. TRI Band mobile radio especially designs for drivers and it pursues company philosophy of innovation and practicality. Precautions Please observe the following precautions to prevent fire, personal injury, or transceiver damage:

Do not attempt to configure your transceiver while driving, it is dangerous. This transceiver is designed for a 13.8V DC power supply. Don't use a 24V battery to power on the transceiver. Do not place the transceiver in excessively dusty, humid or wet areas, nor unstable surfaces. P l e a s e k e e p i t a w a y f r o m interferential devices (such as TV, generator etc.) Do not expose the transceiver to long periods of direct sunlight nor place it close to heating appliances. If an abnormal odor or smoke is detected coming from the transceiver, turn OFF the power immediately. Contact an Anytone service station or your dealer. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference o radio or television reception, which can be determined by turning the equipment off and on, the user encouraged to try to correct the interference by one or more of the following measure:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CONTENTS New and Innovative Features ...................................................1 Frequency Range ...................................................................1 Supplied Accessories ...............................................................2 Supplied Accessories ..............................................................2 Initial Installation .......................................................................3 Mobile installation ...................................................................3 DC Power Cable Connection ..................................................4 Antenna Connection ...............................................................6 Accessories Connections ........................................................7 Getting Acquainted ...................................................................8 microphone .............................................................................8 Basic Operations .......................................................................9 Switching The Power On/Off ...................................................9 Adjusting The Volume ............................................................9 Adjusting Frequency ...............................................................9 Adjusting Channel ...................................................................9 Selecting the frequency band ...............................................10 Receiving ..............................................................................10 Squelch Off/Squelch Off Momentary.....................................10 Shortcut Operations ................................................................11 Squelch level Setup ..............................................................11 Home Channel ......................................................................11 Editing Home Channel ..........................................................11 Hyper Memory channel .........................................................11 Dual Watch............................................................................11 Emergency Alarm ..................................................................11 Channel/Frequency Scan .....................................................11 Channel Scan Skip ...............................................................12 Channel Edit .........................................................................12 Scan range Limit ..................................................................12 Channel Copy .......................................................................12 Channel Delete .....................................................................12 General Setting ........................................................................13 APO (Automatic Power off) ...................................................13 Automatic offset ....................................................................13 VFO Band lockout .................................................................14 Beep Function .......................................................................14 CPU Clock frequency Change ..............................................14 2TONE Encode select ..........................................................14 5TONE Encode select ..........................................................15 Add Optional signaling ..........................................................15 CTCSS/DCS encode Setup .................................................15 Sub Band Display Setup .......................................................16 DTMF Encode Pre-Loading time ..........................................16 DTMF Encode setup .............................................................16 Squelch Mode Setup .............................................................17 Compander ...........................................................................17 Scrambler Setup ...................................................................17 Tone Burst (Pilot Frequency) ................................................18 Keypad Mode Setup .............................................................18 Keypad Lockout ....................................................................19 Squelch Level setup ..............................................................20 Frequency Reverse ...............................................................20 Editing Channel Name ..........................................................20 Channel Function Auto storeage Setup ................................20 Microphone PA,PB, PC,PD key setup ..................................21 RF Squelch level setup .........................................................21 Scan Dwell Time Setup .........................................................21 CONTENTS 1024 groups DCS Code ........................................................32 Priority channel scan .............................................................21 Offset frequency Setup .........................................................22 Display mode Setup ..............................................................22 Busy Channel Lockout ..........................................................22 Radio's DTMF SELF ID ENQUIRY .......................................23 5TONE SELF ID ENQUIR ....................................................23 VFO Frequency Linkage .......................................................23 LCD backlight ........................................................................23 Keypad backlight brightness .................................................24 Calling Record ......................................................................24 AM Function ..........................................................................24 Automatic AM function ..........................................................24 VHF External speaker port ....................................................25 BEEP Volume control ..........................................................25 Talk Around........................................................................... 25 Microphone speaker............................................................. 25 Password Function ...............................................................26 Microphone Operation ............................................................27 Function operation through PA-PD keys ...............................27 Memory Banks .........................................................................29 Assigning A Channel To A Memory Bank ..............................29 Choosing Active Banik ..........................................................29 Bank Linking .........................................................................29 Maintenance .............................................................................30 Default Value For Factory Resume ......................................30 Trouble Shooting ...................................................................30 Specifications ..........................................................................31 Attached Chart .........................................................................32 51 groups CTCSS Tone Frequency(Hz) ...............................32 New and Innovative Features 1 Frequency Range RX: 136~174MHz 220~260MHz 400~512MHz TX: 144~148MHz 222~225MHz 420~450MHz 1 Supplied AcceSSoRieS After carefully unpacking the transceiver, identify the items listed in the table below. We suggest you keep the box and packaging. Supplied Accessories Transceiver Microphone (QHM-05)

(with DTMF keyboard) Mobile Mounting Bracket (QMB-01) DC Power Cable with Fuse Holder(QPL-01) Spare Fuses

(QF-01) User Manual Hardware Kit for Bracket Black screws

(M4X8mm)

(M5X8mm) Tapping screws 4PS(QSS-01A) 4PS(QSS-01B) 2 S-Washer

(QSS-01D) 2

Determine the appropriate angle of the transceiver, using the 3 screw hole positions on the side of the mounting bracket. Initial Installation 3 Mobile inStAllAtion To install the transceiver, select a safe, convenient location inside your vehicle that minimizes danger to your passengers and yourself while the vehicle is in motion. Consider installing the unit at an appropriate position so that knees or legs will not strike it during sudden braking of your vehicle. Try to pick a well ventilated location that is shielded from direct sunlight. 11 Install the mounting bracket in the vehicle using the supplied self-

tapping screws (4pcs) and flat washers (4pcs). Car body 3 Mounting bracket Washer (M5) Tapping screw

(M5X20mm) 21 Position the transceiver, then insert and tighten the supplied hexagon SEMS screws.

Double check that all screws are tightened to prevent vehiclevibration from loosening the bracket or transceiver. dc poweR cAble connection Locate the power input connector as close to the transceiver as possible. NOTE Mobile opeRAtion The vehicle battery must have a nominal rating of 12V. Never connect the transceiver to a 24V battery. Be sure to use a 12V vehicle battery that has sufficient current capacity. If the current to the transceiver is insufficient, the display may darken. 11 Route the DC power cable supplied with the transceiver directly to the vehicle's battery terminals using the shortest path from the transceiver.

We recommend you do not use the cigarette lighter socket as some cigarette lighter sockets introduce an unacceptable voltage drop. The entire length of the cable must be dressed so it is isolated from heat, moisture, and the engine secondary (high voltage) ignition system/ cables.

21 31 41 After installing cable, in order to avoid the risk of damp, please use heat-resistant tap to tie together with fuse box. Don't forget to reinforce whole cable. In order to avoid the risk of short circuit, please cut down connection with negative (-) of battery, then connect with radio. Confirm the correct polarity of the connections, then attach the power cable to the battery terminals; red connects to the positive

(+) terminal and black connects to the negative (-) terminal.

Use the full length of the cable without cutting off excess even if the cable is longer than required. In particular, never remove the fuse holders from the cable. Initial Installation 51 Reconnect any wiring removed from the negative terminal. 3 Red Black 61 Connect the DC power cable to the transceiver's power supplyconnector.

Press the connectors firmly together until the locking tab clicks. If the ignition-key on/off feature is desired (optional feature), use the 4 DC power cable Ext. Power jack optional QCC-01(For Cigar-Plug connection) cable. Connect one of the cables between the ACC terminal or a Cigar-Plug that operates with the vehicle ignition or ACC switch on the vehicle and EXT POWER jack on the rear side of the unit. In many cars, the cigar-lighter plug is always powered. If this is the case, you cannot use it for the ignition key on/off function. NOTE 11 3 71 81 91 111 Initial Installation When the ignition key is turned to ACC or ON(Start) position with the radio turned off, the power switch illuminates. The illumination will be turned off when the ignition key is turned to the off position. To turn on the unit, press the power switch manually while it is illuminated. (While ignition key is at ACC or ON position). When the ignition key is turned to ACC or ON position with the radio's power switch on, the unit turns on automatically and the power switch will be lit. Turn the ignition key to OFF position or manually turn the power switch off to shut down the radio. Using extra cable, power consumption: 5MAH. Without this function, user can turn on/off radio by Power knob. Connect the DC power cable to the regulated DC power supply and ensure that the polarities are correct. (Red: positive, Black:negative).

Do not directly connect the transceiver to an AC outlet. Use the supplied DC power cable to connect the transceiver to a regulated power supply. Do not substitute a cable with smaller gauge wires.

Regulated power supply

(QRP-01) Red Black Regulated power supply (QRP-01) ACC terminal 5 Cigar-Plug connection Ext. Power jack DC power cable with fuse holder (QPL-01) 21 Connect the transceiver's DC power connector to the connector on the DC power cable. Press the connectors firmly together until the locking tab clicks. Fixed StAtion opeRAtion In order to use this transceiver for fixed station operation, you will need a separate 13.8V DC power supply (not included), power supply (QRP-01) as optional accessories. Please contact local dealer to require. The recommended current capacity of your power supply is 12A.

Before connecting the DC power to the transceiver, be sure to switch the transceiver and the DC power supply OFF. Do not plug the DC power supply into an AC outlet until you make all connections. NOTE Initial Installation 3 an impedance other than 50 reduces the efficiency of the antenna system and can cause interference to nearby broadcast television receivers, radio receivers, and other electronic equipment.

All fixed stations should be equipped with a lightning arrester to reduce the risk of fire, electric shock, and transceiver damage. NOTE The possible locations of antenna on a car are shown as following:

6 ReplAcinG FuSeS If the fuse blows, determine the cause, then correct the problem. After the problem is resolved, replace the fuse. If newly installed fuses continue to blow, disconnect the power cable and contact your authorized dealer or an authorized servicecenter for assistance. Fuse Location Transceiver Supplied Accessory DC power cable Fuse Current Rating 15A 20A Only use fuses of the specified type and rating, otherwise the transceiver could be damaged. If you use the transceiver for a long period when the vehicle battery is not fully charged, or when the engine is OFF, the battery may become discharged, and will not have sufficient reserves to start the vehicle. Avoid using the transceiver in these conditions. NOTE AntennA connection Before operating, install an efficient, well-tuned antenna. The success of your installation will depend largely on the type of antenna and its correct installation. The transceiver can give excellent results if the antenna system and its installation are given careful attention. Use a 50 impedance antenna and low-loss coaxial feed-line that has a characteristic impedance of 50 , to match the transceiver input impedance. Coupling the antenna to the transceiver via feed-lines having Initial Installation 3 AcceSSoRieS connectionS exteRnAl SpeAkeR If you plan to use an external speaker, choose a speaker with an impedance of 8. The external speaker jack accepts a 3.5mm (1/8") mono (2-conductor) plug. Antenna[QCA-02]

Microphone[QHM-04]

SP-02 External speaker[SP-02]

7 MicRophone For voice communications, connect a microphone equipped with an 8-pin modular plug into the modular socket on the front of the main unit. Press firmly on the plug until the locking tab clicks. Attach the supplied microphone hanger in an appropriate location using the screws included in the screw set. Microphone connector Sub Speaker Main Speaker MicRophone 7 8 1 2 10 5 4 6 9 Getting Acquainted 4 FUNCTION Increase frequency, channel number or setting value. Decrease frequency, channel number or setting value. Input VFO frequency or DTMF dial out etc. Choose left band or right band as Main band The indicator light on for Main band. NO. KEY UP DOWN Number Key A/B band Band indicator 1 2 4 5 6 7 RX indicator Light green while receiving. 8 MIC 9 Speaker 10 Lock UP/down Speak here during transmission. When shut the speaker in the base, you can hear the calling by this speaker. When this key is in up position, It is unlock UP/DOWN key, when this key is in down poisition, UP/DOWN key will be locked. 8 3 MIC Connector Diagram(in the front view of connector) Key Pad Serial Data

+5V DOWN UP MIC GND MIC PTT GND 5 Basic Operations SwitchinG the poweR on/oFF poweR on Press key to switch the transceiver ON, the LCD displays "WELCOME ANYTONE", then display current frequency or channel. poweR oFF Power Press transceiver OFF. key for over 0.5 Second to switch the AdjuStinG the VoluMe Rotate the [VOLUME] knob of selected band clockwise to increase the volume, counterclockwise to decrease the volume. 9 Min Volume Max Volume NOTE Hold

,keep pressing it to Monitor the background noise after the transceiver emits a DU beep, meanwhile adjust the [VOLUME] knob. During communication, volume can be adjusted more accurate. AdjuStinG FRequency AdjuStinG FRequency thRouGh SelectoR knob Decrease frequency Increase frequency In frequency (VFO) mode, turn the selector knob clockwise to increase frequency;

counterclock-wise to decrease frequency. Every gear will increase or decrease frequency by one step. To adjust the Main band frequency, press corresponding selector knob, the left side of decimal point will flash. In this status, turn the selector knob will increase or decrease frequency quickly by 1MHz step. The microphone [ UP/DOWN ] key also able to adjust frequency. Press [ UP/DOWN ] key will increase(decrease) the frequency by one step size. Hold [ UP/DOWN ] key will adjust the frequency continuously. NOTE input FRequency thRouGh MicRophone nuMbeR key In VFO mode, you can input the frequency by the microphone numeric key. It is invalid to input frequency out of the frequency band. For example:

to input 150.125Mhz, press 1, 5, 0, 1, 2, 5 continuously. to input 152 MHz, press1, 5, 2, continuously. When the Band lockout function is on, the input or adjusting of frequency bandwill limit within the current VFO band. NOTE AdjuStinG chAnnel AdjuStinG chAnnel thRouGh SelectoR knob In channel mode, you can adjust the channel directly by the channel knob. Turn clockwise to increase one channel; turn counterclockwise to decrease one channel. To adjust the Main band channel, press correspondent selector knob, the channel number flashes in this situation, the channel number will increase 10 channels by each gear of selector knob. Press microphone [ UP/DOWN ] key also able to adjust the channel. If there is any empty channel, the adjustment will ignore it and jump to next channel. NOTE Basic Operations 5 Squelch oFF/Squelch oFF MoMentARy key can be set up as Squelch Off or Squelch Off Long press of Momentary to monitor the weak signal. 1. Squelch Off: Hold repeat the above operation to resume squelch. key until hear "Du" beep, the squelch is off, 2. Squelch Off Momentary: Keep hold release the key to resume squelch. In standby, press the microphone to turn on the squelch. NOTE key to disable squelch, to cancel squelch, press it again 10 input chAnnel thRouGh MicRophone nuMbeR key In channel mode, you can switch to desired channel by press 3 of the microphone numeric keys (001-750). For example input 001 get channel 1; input 030 is channel 30; input 512 is channel 512. If the input channel is no frequency, the transceiver will emit a warning beep and return to last channel. SelectinG the FRequency bAnd 1. Choose for Left band: press the left side key to switch it to VFO mode, press the left selector knob over 1 second then repeat above operation will switch the left band. 2. Choose for right band: press the right side key to switch it to VFO mode, press the right selector knob over 1 second then repeat above operation will switch the right band. This transceiver can be set working on 2 UHF band or 2 VHF band. NOTE ReceiVinG In standby, both left band and right band are able To receive. When they receive any signal, the BUSY icon and signal strength icon will appear in the corresponding area of the LCD. And you can hear the calling. If the transceiver has set at higher squelch level, it may fail to hear the calling. If the BUSY and signal strength icon display in left band or right band, but can not hear the calling, means the signal is with matching carrier but dis-matching signaling. NOTE 6 Shortcut Operations Squelch leVel Setup This function is used to setup the strength of receiving signal, when the strength reach a certain level, the calling can be heard, otherwise, the transceiver will keep mute. In standby, press and hold to adjust the squelch level of Main band. 1-20: Total 20 squelch levels available. OFF: turn off squelch. The background noise always on. key, meanwhile switch the selector knob The squelch level shall setup separately for right band and left band. NOTE hoMe chAnnel In standby, press key to switch to HOME channel, and communicate on HOME channel. repeat pressing it to return to last channel. 11 editinG hoMe chAnnel In VFO mode, after setting desired freq and Channel, press until radio announces"DUDU", LCD displays H icon, Home channel editing finished. then hold hypeR MeMoRy chAnnel In standby, press the left or right volume knob will switch the radio work on hyper channel 1 or hyper channel 2. duAl wAtch key for over 0.5 second to enter Dual Watch mode. In standby, hold The radio will scan the channel in every 5 seconds. When the radio receives matching signal, it pause scanning until the signaling disappear. Repeat above operation to exit Dual watch. eMeRGency AlARM To start emergency alarm, hold the right volume knob until the trans

-ceiver displays ALARM and emit alarm. Re-power on the transceiver to exit alarm. This transceiver has 4 kind of alarm. chAnnel/FRequency ScAn FRequency ScAn In VFO mode, this function is designed to monitor signal of every communicative frequency point of "step size" you have set. 11 21 In VFO mode, press the Main Band During the scanning adjust the Main band selector knob or press microphone [ UP/DOWN ] key will change the scan direction. Press key to enter channel scan. key to exit scan. chAnnel ScAn In channel mode, press the Main Band key to enter channel scan. 31 11 Shortcut Operations 6 21 31 During the scanning, adjust the Main band selector knob or press microphone [ UP/DOWN ] key will change the scan direction. Press key to exit scan. chAnnel ScAn Skip In channel mode, switch selector knob to choose the channel, then hold for over 0.5 second, the radio prompts "DU DU", and LCD displays "SKIP", and now the current channel is Scan Skip. 11 21 31 41 the selector knob to choose the channel. key until the transceiver prompt a Du and channel number chAnnel copy In channel mode, turn Hold display flashes. Turn selector knob to choose channel number for storage. ( If the storage has data, the LCD will display the frequency, otherwise will display "----------") Hold key, the LCD displays MEN-IN, channel copy completed. key until the transceiver prompt chAnnel edit In VFO mode, turn selector knob to select the desired frequency or input frequency by MIC's numeric keys. Hold DU and the display of channel number flashes. Turn selector knob to select the channel number to store. (If the storage has data, the LCD will display the frequency, otherwise will display"----------") Hold key, the LCD display MEN- IN, the channel edit completed. 11 21 31 41 ScAn RAnGe liMit You can set the VFO scan frequency range by this function:

11 Choose upper limit and lower limit frequency, there are L1/U1- L5/

U5, five couple of limit frequency for selection. L stands for lower limit and U stands for the upper limit. the upper limit must over the lower limit frequency. Please refer to the Channel Edit to setup the limit frequency. In VFO mode, set the VFO frequency in the range between upper and lower limit. Press key to start scan in lmited range. 21 31 key until the transceiver prompt DU, and chAnnel delete In standby, hold channel number flashes. Turn selector knob to choose channel number for delete. (If the 11 21 storage has data, the LCD will display the frequency, otherwise will display "----------") Hold prompt and LCD displays MEN-OUT, the channel delete completed. Left band volume knob, until the transceiver emit DU DU 31 12 7 General Setting Basic operation steps for Function menu 11 Press key to enter function menu. 21 Turn the Main band selector knob to choose wanted function. 31 Press the Main band selector knob to enter function setup. 41 Switch the Main band selector knob to choose wanted value. 51 Press the Main band selector knob to store value and back to key or hold selector knob for over 0.5 function menu. Press second to store setup and exit. Apo (AutoMAtic poweR oFF) 13 key to enter function menu. Once APO is activated, the transceiver will be automatically switched off when the pre-set timer running out. 11 Press 21 choose No. 01 menu. The LCD displays Turn the Main band selector knob to

"APO". 31 Press the Main band selector knob to enter function setup. 41 choose wanted value. Available values:

Switch the Main band selector knob to 51 key to store value and 0.5-12Hours, OFF Press the Main band selector knob or back to function menu. Press setup and exit. key or hold selector knob for over 0.5 second to store FRequency chAnnel Step Setup Press Turn the Main band selector knob to choose Only in frequency (VFO) mode, this function is valid. Turn selector knob to select frequency or frequency scanning which is restricted by frequency step size. 11 key to enter function menu. 21 No. 03 menu. the LCD displays "STEP". 31 41 Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted value. Av a i l a b l e Va l u e s : 2 . 5 K , 5 K , 6 . 2 5 K , 8.33K,10K,12.5K,15K,20K, 25K. Press the Main band selector knob or back to function menu. Press setup and exit. key or hold selector knob for over 0.5 second to store key to store value and 51 This function is auto-hidden in channel mode NOTE VFo bAnd lockout key to enter function menu. In VFO mode, when this function is on, the scanning or input of frequency will restricted within the current VFO frequency band. 11 21 31 41 Press Turn the Main band selector knob to choose No. 04 menu. the LCD displays "BAND". Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted value. ON: Turn on VFO band lockout function OFF: Turn off VFO band lockout function Press the Main band selector knob or key to store value and back to function menu. Press or hold selector knob for over 0.5 second to store setup and exit. key key to enter function menu. beep Function Press Turn the Main band selector knob to choose No. 05 menu. the LCD displays "BEEP". Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted value. ON: Turn on Beep function. OFF: Turn off Beep function Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. key to store value and key or hold selector knob for over 51 11 21 31 41 51 General Setting 7 cpu clock FRequency chAnGe key to enter function menu. When any harmonic or image frequency in the CPU clock disturbs the working frequency, turn on this function will cut the disturbing 11 Press 21 choose No. 06 menu. the LCD displays Turn the Main band selector knob to 31 41

"CLK.SFT". Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted value. ON: Turn on CPU Clock frequency Change. OFF: Turn off CPU Clock frequency Change. Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. 2tone encode Select Press Turn the Main band selector knob to choose No. 07 menu. the LCD displays "2TN ENC". Press the Main band selector knob to enter function setup. Switch the Main band selector knob to Available Values: 0-23, total 24 groups. key to store value and key or hold selector knob for over key to enter function menu. 51 11 21 31 41 choose wanted value. If the 2TONE encode are set up with name, the LCD will display corresponding name. NOTE 51 Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. key to store value and key or hold selector knob for over 14 General Setting 7 5tone encode Select 11 Press key to enter function menu. 21 choose No. 08 menu. the LCD displays Turn the Main band selector knob to 31 41 choose wanted value.

"5TN ENC". Press the Main band selector knob to enter function setup. Switch the Main band selector knob to Available Values: 0-99, total 100 groups. if the 5TONE encode are set up with name, the LCD will display corresponding name. NOTE 51 15 Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. Add optionAl SiGnAlinG key to store value and key or hold selector knob for over key to enter function menu. This transceiver has 3 optional signaling: DTMF/5Tone/2Tone,those signaling function similar to CTCSS/DCS signaling. DTMF and 5Tone signaling can be applied for other advanced features such as ANI, group call, select call, remotely stun, remotely kill waken etc.. 11 21 Press Turn the Main band selector knob to choose No. 09 menu. The LCD displays "TON DEC". Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted value DT: means DTMF signaling is added. 2T: means DTMF signaling is added. 5T: means DTMF signaling is added. 31 41 51 OFF: Turn off optional signaling Press the Main band selector knob or key to store value and back to function menu. Press or hold selector knob for over 0.5 second to store setup and exit. key The working of optional signaling shall be work associated with the squelch mode setup. (Refer to Squelch Mode setup in page 20) NOTE 11 21 31 41 51 61 71 key to enter function menu. ctcSS/dcS decode Setup Press Switch the Main band selector knob to choose No.11 menu, the LCD displays

"RX CDCS". Press the Main band selector knob to enter function setup Switch the Main band selector knob to choose wanted value OFF: Turn off CTCSS/DCS decode. CTCSS: Choose CTCSS decode. DCS: Choose DCS decode. Press the Main band selector knob to enter the menu. Switch the Main band selector knob to choose wanted CTCSS, DCS code. CTCSS: 62.5-254.1HZ, and one self-

defined group, total 52 groups DCS: 000N-777I, total 1024 groups Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. key to store value and key or hold selector knob for over The working of CTCSS/DCS decode shall be work associated with the squelch mode setup. (Refer to Squelch Mode setup in page 20) NOTE General Setting 7 to enter function menu dtMF encode Setup Press Switch the Main band selector knob to choose No.15 menu, the LCD displays

"DTMF W". Press the Main band selector knob to enter function setup. Switch the Mai press key back to DTMF menu. 01-16: total 16 group of DTMF code. n band selector knob to choose DTMF group. Then When the selected group is empty, the LCD displays '------". Press the selector knob to enter the DTMF signaling edit. The LCD display "-- -- -- -- -- --", the last character flashes. Switch the selector knob to choose wanted character. Press the selector knob to confirm selected value and start edit for next character. Press again to store setup and exit. Press for over 0.5 second to store setup and exit. key key or hold selector knob key to store value and exit code editing. Press 16 11 21 31 41 51 61 71 81 key to store value and key or hold selector knob for over 11 21 31 41 51 11 21 31 41 51 key to enter function menu. Sub bAnd diSplAy Setup Press Turn the Main band selector knob to choose No. 12 menu. the LCD displays "DSP SUB"

Press the Main band selector knob to enter function setup Switch the Main band selector knob to choose wanted value. FREQ: display sub band frequency, DC-IN: display sub band voltage. OFF: turn off display for sub Band Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. dtMF encode pRe-loAdinG tiMe Press Turn the Main band selector knob to choose No. 13 menu. the LCD displays

"DTMF D". Press the Main band selector knob to enter function setup Switch the Main band selector knob to choose wanted value. 100MS: The Pre-Loading time is 100MS 300MS: The Pre-Loading time is 300MS 500MS: The Pre-Loading time is 500MS 800MS: The Pre-Loading time is 800MS 1000MS: The Pre-Loading time is 1000MS Press the M back to function menu. Press 0.5 second to store setup and exit. key to enter function menu. ain band selector knob or key to store value and key or hold selector knob for over General Setting 7 Squelch Mode Setup coMpAndeR key to enter function menu. This transceiver has 5 squelch modes available. Squelch function is used for increase the level of filtering unwanted signal, and free from disturb. 11 21 31 41 Press Turn the Main band selector knob to choose No.16 menu. The LCD displays "SGN SQL"

Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted value. SQ: You can hear the calling once receives matching carrier. CTSS/DCS: You can hear the calling when receives matching carrier and CTCSS/DCS code. 17 TONE: You can hear the calling when receives matching carrier +

optional signaling. CT*TO: You can hear the calling when receives matching carrier +

CTCSS/DCS + optional signaling. CT/TO: You can hear the calling when receives any matching carrier or CTCSS/DCS or optional signaling. Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. key to store value and key or hold selector knob for over 51 NOTE Only when the transceiver is set with CTCSS/DCS or optional DTMF/5TONE/TONE signaling, the values will be available.VHF2 no optional DTMF/5TONE/2TONE signaling decode setup. key to enter function menu Compander function will decrease the background noise and enhance audio clarity, especially in long range communication. 11 21 Press Turn the Main band selector knob to choose No 17 menu. The LCD displays

"COMP"

Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted value. ON: Compander function is turn on OFF: Compander function is turn off Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. key to store value and key or hold selector knob for over 31 41 51 When using compander, to avoid distortion during communications, both radios need turn on this function. NOTE ScRAMbleR Setup This special audio process can offer a more confidential communication;

other radio with same frequency will receive only disordered noises. 11 21 Press Turn the Main band selector knob to choose No.18 menu. The LCD displays "SCR". key to enter function menu. 31 41 51 Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted group 1-9 (9 fix groups) U1, U2 (2 self defined scrambler groups), OFF. Press the Main back to function menu. Press 0.5 second to store setup and exit. band selector knob or key to store value and key or hold selector knob for over To enable communication with scrambler, 2 transceivers shall set with same group. NOTE tone buRSt (pilot FRequency) key to enter function menu. This function uses to start repeater. It needs certain intensity Pilot Frequency to start a dormant repeater. As usual, no need to send pilot frequency again once repeater started. 11 21 Press Turn the Main band selector knob to choose No.19 menu. The LCD displays

"TBST". Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted frequency. 1000: Pilot Frequency is 1000Hz. 1450: Pilot Frequency is 1450Hz. 1750: Pilot Frequency is 1750Hz. 2100: Pilot Frequency is 2100Hz. 31 41 General Setting 7 Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. key to store value and key or hold selector knob for over key to enter function menu. keypAd Mode Setup Press Turn the Main band selector knob to choose No.20 menu. The LCD displays

"KEYMOD". Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted mode. KEY1: key1 mode, Normal mode, the left 4 keys have same functions as the right 4 keys. KYE2: the left 4 keypads will shared by both band. And the right 4 key pads will be re-defined. Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. key to store value and key or hold selector knob for over 18 51 11 21 31 41 51 Notice: Definition of Keypad in KEY2 mode:

11 21 long press: In standby, long press this key to add/

Left delete optional signaling, repeat the long press it will set optional signaling DTMF, 5TONE or 2TONE. When the LCD displays DT means DTMF, displays 5T means 5TONE, displays 2T means 2TONE. Right Short press: In VFO mode, short press this key, 7 General Setting 31 41 51 61 71 19 long press: In stand by, hold this key until the

, means the compander function is on, the frequency step size changes to 1Mhz, in channel mode, adjust selector knob will jump 10 channels. long press: Talk Around. When this function is Right activated, transceiver can not communicate with repeater. Repeat the operation to turn off Talk Around. Right short press: Frequency reverse function, when current channel is setup with offset direction and offset frequency, press this key will turn on frequency reverse function.The signaling will also be reversed if CTCSS/DCS signaling existed in this channel. Repeat the short press it will turn off Frequency reverse function. Right LCD displays repeater above operation to turn off compander function. Right CTCSS/DCS code for current channel. When the LCD displays ENC, the current channel is with CTCSS encode function. When the LCD displays ENC and DEC, the current channel is with CTCSS /DCS code function. When the LCD displays DCS and DCS icon, the current channel is with CTCSS code function. When the LCD displays OFF, the current channel is without CTCSS /DCS function. long press: In standby, long press this key to Right enter CTCSS/DCS scan, when find matching CTCSS/DCS signal, the scan will pause in the way following Scan Dwell time.The scan direction can be changed by corresponding channel selector knob. Note:To enable this function, the channel shall be set up with CTCSS/DCS decode. short press: In standby, press this key to set the 11 21 31 41 51 81 91 Right short press, shot press this key, the sub band will display "MAIN" and flashes.In this case, you can setup for sub band without switch between Main band and Sub band. Right long press, choose scrambler group for Main band. In standby, hold this key, the LCD displays SCR X and icon. X stands for the group number, repeater above operation to choose wanted group. key to enter function menu. keypAd lockout Press Turn the Main band selector knob to choose No.21 menu. The LCD displays "LOCK". Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted mode. ON: The keypad lockout function is turn on, all keys beside and band switch knobare invalid. OFF: The keypad lockout function is turn off. Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. key to store value and key or hold selector knob for over 11 21 31 41 51 key to enter function menu. Squelch leVel Setup Press Turn the Main band selector knob to choose No.23 menu. The LCD displays

"SQL". Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted value 1-20: total 20 squelch levels OFF: Turn off squelch function, the background noise keep on. Press the Main band selector knob or to function menu. Press second to store setup and exit. key to store value and back key or hold selector knob for over 0.5 FRequency ReVeRSe key to enter function menu. With this function on, the transceiver will be able to communicate with a transceiver in same network without through a repeater. 11 21 Press Turn the Main band selector knob to choose No 24 menu. The LCD displays "REV"

Press the Main band selector knob to enter function setup. 31 41 Switch the Main band selector knob to choose wanted value. ON: Frequency Reverse is turn on. OFF: Turn off Frequency Reverse. Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. 51 key to store value and key or hold selector knob for over editinG chAnnel nAMe General Setting 7 key to enter function menu. After edit a name for a channel, if the display mode is channel name, the will display the name edited in this menu. Otherwise it will display the frequency. 11 Press 21 Switch the selector knob to choose NO.26 function menu, the LCD displays "NAME C". 31 Press the Main band selector knob to enter function setup. 41 Switch the selector knob to choose wanted character. 51 Press the selector knob to confirm current character and start edit next character, after editing all 7 characters, press the selector knob to confirm and back to function menu. If the editing not reach 7 characters, press menu, then press to store setup and exit. key back to function key or hold selector knob for over 0.5 second 61 20 chAnnel Function Auto StoRAGe Setup This function is used to store lastest setup for each single channel. when this function is on, all the latest temporary operation for present channel will be stored no matter change channel or power off radio. when this function is off, the temporary setup will not be stored, the channel informaiton will resume to the last stored value after change channel or power off radio. 11 21 Press Turn the Main band selector knob to choose NO.27 menu, the LCD displays

"HYPER". Press the Main band selector knob to enter function setup. to enter function menu 31 7 General Setting 41 51 11 21 Switch the Mian band selector knob to choose wanted value. MANUAL: Auto storage is turn off. AUTO: Auto storeage is turn on. Press the Main band selector knob or back to function menu. Press 0.5 second to sore setup and exit. MicRophone pA,pb, pc,pd key Setup Press key to enter function menu. Turn the Main band selector knob to choose No.28-31 menu. The LCD displays

"PG PA", "PG PB", "PG PC", "PG PD". Press the Main band selector knob to enter function setup. key to store value and key or hold selector knob for over 31 41 Switch the Main band selector knob to choose wanted value. 51 Press the Main band selector knob or key to store value and back to function menu. Press key or hold selector knob for over 21 0.5 second to store setup and exit. For Menu details, please refer to Page 30-31, Microphone Operation. NOTE RF Squelch leVel Setup key to enter function menu. When squelch level function is on, you can cancel squelch only when the signal strength reach the level setup by users. 11 21 Press Turn the Main band selector knob to choose No.32 menu. The LCD displays

"RF SQL". Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted value. S-2: Able to hear the calling when the power meter reach 1 bar. 31 41 S-5: Able to hear the calling when the power meter reach 4 bar. S-9: Able to hear the calling when the power meter reach 8 bar. S-FULL: Able to hear the calling when the power meter reach full bar. Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. key to store value and key or hold selector knob for over key to enter function menu. ScAn dwell tiMe Setup Press Turn the Main band selector knob to choose No.34 menu. The LCD displays

"SCAN". Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted value. TIME: it pauses 5s once scanning a matching signal, then resume scan. BUSY: it pauses once scanning a matching signal, then resume scan after the signal disappeared for 2 seconds. SECEDE: It Stops once scanning a matching signal, and exit scan. Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. key to store value and key or hold selector knob for over key to enter function menu. pRioRity chAnnel ScAn Press Turn the Main band selector knob to choose No.35 menu. The LCD displays

"SCAN M". 51 11 21 31 41 51 11 21 31 41 51 Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted value. MEN: Channel Scan, the transceiver will scan all the channels after enter channel scan. MSN: Priority Channel Scan, the transceiver will only scan the priority channel after enter channel scan. Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. key to store value and key or hold selector knob for over NOTE Before using Priority channel scan function.the edited channel shall be set up as "P SCAN" or refer to the PRI instrunction in page 29 to add or delete priority channel. 51 oFFSet FRequency Setup Press Turn the Main band selector knob to choose 11 key to enter function menu. 21 No.36 menu. The LCD displays "SHIFT". 31 41 Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted value. Available Offset frequency for this transceiver is 0-100MHz. Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. diSplAy Mode Setup 11 Press 21 choose No.37 menu. The LCD displays Turn the Main band selector knob to key to enter function menu. 51

"DISPLAY". key to store value and key or hold selector knob for over 11 21 31 41 51 General Setting 7 31 Switch the Main band selector knob to choose wanted value. Press the Main band selector knob to enter function setup. 41 FREQ: The radio displays channel number + frequency in channel mode, if press key,it will change to VFO mode. CH: Displays only channel number. NAME: In channel mode, It displays the channel number and channel name if the current channel is set up with a name. Otherwise, it display the channel number and frequency.If press key, it will change to VFO mode. 22 key to store value and key or hold selector knob for over Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. buSy chAnnel lockout Press key to enter function menu. Turn the Main band selector knob to choose No.38 menu. The LCD displays

"REPLOCK". Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted value. RLORP: Signaling busy lockout, when current channel receives a matching carrier but dis-matching CTCSS/DCS. RLOBU: Channel busy lockout, when current channel receives a matching carrier;

OFF: Busy channel lockout is disabled. Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. key to store value and key or hold selector knob for over 11 21 31 41 11 21 31 41 23 General Setting key to enter function menu. 7 RAdio'S dtMF SelF id enquiRy Press Switch the selector knob to choose No. 39 function. The LCD displays "DTMF ID". Press the Main band selector knob to enter function setup. The LCD will show the DTMF self ID. Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. key to store value and key or hold selector knob for over key to enter function menu. 5tone SelF id enquiRy Press Switch the selector knob to choose No.40 function. The LCD displays "5TONE ID". Press the Main band selector knob to enter function setup. The LCD will show the 5TONE self ID. Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. VFo FRequency linkAGe key to store value and key or hold selector knob for over Enable this function, the adjustment for any band of VFO frequency, will bring same frequency change to both bands. Adjust one gear, the frequency for both bands will increase or decrease one step size value. 11 21 Press Turn the Main band selector knob to choose No.42 menu. The LCD displays

"VFOTR". key to enter function menu. 31 41 51 Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted value. Available Values: ON, OFF. Press the Main band selector knob or key to store value and back to function menu. Press or hold selector knob for over 0.5 second to store setup and exit. key This function is only valid when both bands work on VFO mode. NOTE 11 21 31 41 51 key to enter function menu. lcd bAckliGht Press Turn the Main band selector knob to choose No. 45-47 menu. The LCD displays "COL RED","COL GRN","COL BLU". Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted value.Each color (Red, blue, Green) with 32 brightness levels. Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. key to store value and key or hold selector knob for over key to enter function menu. keypAd bAckliGht bRiGhtneSS 11 Press 21 No. 48 menu. The LCD displays "DIMMER". Turn the Main band selector knob to choose 31 41 51 Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted value. Available value: 32 brightness levels. Press the Main band selector knob or key to store value and back to function menu. Press selector knob for over 0.5 second to store setup and exit. key or hold General Setting 7 AM Function Press Turn the Main band selector knob to choose 11 key to enter function menu. 21 No. 50 menu. The LCD displays "AM". 31 41 Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted value. ON: turn on AM function. OFF: turn off AM function. Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. 51 key to store value and key or hold selector knob for over cAllinG RecoRd key to enter function menu. The transceiver offers enquiry of calling record. 11 21 31 41 choose wanted value. Press Turn the Main band selector knob No. 49 menu. The LCD displays "NOTE". Press the Main band selector knob to enter function setup. Switch the Main band selector knob to to choose 51 This transceiver is able to record 16 calling at most. Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. key to store value and key or hold selector knob for over This function is only valid when the Main band frequency is VHF 108-

180MHz, the function is invalid when the right band is set as Main band. NOTE 24 AutoMAtic AM Function The radio will automatically boot AM function when the VHF frequency is under 136Mhz. 11 Press key to enter function menu. 21 No. 51 menu. The LCD displays "AUT AM". Turn the Main band selector knob to choose 31 41 Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted value. ON: turn on auto AM function. OFF: turn off auto AM function. Press the Main band selector knob or back to function menu. Press 0.5 second to store setup and exit. key to store value and key or hold selector knob for over 51 To enable Automatic AM function, the AM function shall be turned on first. NOTE General Setting 7 VhF exteRnAl SpeAkeR poRt key to enter function menu. When the function setup as external (EXT), in order to hear the calling on VHF, user can use sub speaker or connect an external dual track speaker

(SP-02). The calling from VHF and UHF are separated in 2 tracks. 11 Press 21 choose No. 52 menu. The LCD displays Turn the Main band selector knob to 31 41

"VSPCONT". Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted value. INT: Use main internal speaker, the sub internal speaker will be shut off. VHF and UHF band share main speaker EXT: Use sub internal speaker or external speaker, the VHF calling can be heard from the sub speaker or external speaker. 51 25 Press the Main band selector knob or back to function menu. Press second to store setup and exit. key to store value and key or hold selector knob for over 0.5 beep VoluMe contRol key to enter function menu. 11 Press 21 Turn the Main band selector knob to choose No. 53 menu. The LCD displays BP-VOL. 31 Press the Main band selector knob to enter function setup 41 Switch the Main band selector knob to choose wanted value. LOW: BEEP volume is low. HIGH: BEEP volume is high. 51 Press the Main band selector knob or back to function menu. key to store value and tAlk ARound With this function on, the transceiver will not able to communicate with another transceiver through a repeater. key to enter function menu. menu. The LCD displays TALK. 11 Press 21 Turn the Main band selector knob No.54 31 Press the Main band selector knob to enter function setup. 41 Switch the Main band selector knob to choose wanted value ON: Turn on Talk Around OFF: Turn off Talk Around 51 Press the Main band selector knob or back to function menu. Press second to store setup and exit. key to store value and key or hold selector knob for over 0.5 MicRophone SpeAkeR key to enter function menu. 11 Press 21 Turn the Main band selector knob to choose No.55 menu. The LCD displays HND SPK. 31 Press the Main band selector knob to enter function setup. 41 Switch the Main band selector knob to choose wanted value HSPKOFF: Turn off microphone speaker. HSPK ON: Turn on microphone speaker. MSPKOFF: Turn off Main speaker. 51 Press the Main band selector knob or to function menu.Press to store setup and exit. key to store value and back key or hold selector knob for over 0.5 second When turn on microphone speaker, please set up Menu 52 VSPCONT to be INT, otherwise the VHF signal can not be monitored. NOTE General Setting 7 key to enter function menu. pASSwoRd Function 11 Press 21 No.68 menu. The LCD displays "PASSWD". Turn the Main band selector knob to choose 31 41 Press the Main band selector knob to enter function setup. Switch the Main band selector knob to choose wanted value. ON: Turn on password function. OFF: Turn off password function. Press the Main back to function menu. Press 0.5 second to store setup and exit. band selector knob or 51 key to store value and key or hold selector knob for over When password function is on, correct password shall be input after power on. The password shall be set up before using this function. NOTE 26 8 Microphone Operation MIC Main/Sub band switch UP DOWN Numeric Keys UP/DOWN lock key Microphone speaker You can operate the transceiver by keypad or input desired frequency and channel through the QHM-05 microphone. 27 Function opeRAtion thRouGh pA-pd keyS The PA, PB, PC, PD, keys can be set up with the following functions. RPTR: OFFSET direction setup, in standby, press the key RPTR function will change the offset direction. When LCD displays"+", means plus offset, when the LCD displays"-", means minus offset. This function is valid only when current channel set with offset frequency. NOTE PRIAdd or delete priority channel: In channel mode, press the key PRI function to set priority channel, when the LCD displays the current channel is set as priority channel. Repeat above operation, the disappear, the curent channel is not set as priority channel. TONE: CTCSS/DCS code setup. In standby, press the key TONE function will be able to setup CTCSS/DCS code. When the LCD displays "ENC"

and CTCSS frequency, press the [ UP/DOWN ] key to choose CTCSS encode. When the LCD displays "ENC", "DEC"

and CTCSS frequency, press the microphone

[ UP/DOWN ] key to choose CTCSS decode. When the LCD displays "DCS" and DCS code, press the microphone [

UP/DOWN ] key to choose DCS code. MHZ: In VFO mode, press the key MHZ function, the megabit digital in the LCD flashes, now turn the channel knob or microphone [ UP/DOWN ] key to adjust frequency by 1Mhz step. In channel mode, press this key, the channel number flashes, now adjust selector knob or microphone [ UP/DOWN ] key to adjust channel. REV: In standby, press the key "REV" function to turn-on or turn off Frequency Revrse function. HOME: HOME channel switch, in standby press the key "HOME" function to switch between HOME channel and current channel. MAIN: Main band switch, in standby press the key "MAIN" function to choose left band or right band as Main band. VFO/MR: Working mode switch, in standby, press the key "VFO/MR" function to switch between channel mode and frequency mode. Microphone Operation 8 28 SCAN: scan function, in standby, press the key "SCAN" function to start channel scan or frequency scan. SQL OFF:Turn off Squelch, in standby, press the key "SQL OFF" function to turn off squelch, you can hear very weak signal, repeat the above function to turn on squelch. COMP: Compander function in standby, press the key "COMP" to turn on or turn off Compander function. SCR: Scrambler function, in standby, press the key "SCR" function to turn on or turn off Scrambler function. And choose optional scrambler groups (from 9 fixed groups and 2 self defined groups). TONE DEC: Add Optional Signaling, in standby press the key "TONE DEC"

function to choose DTMF(DT), 2TONE(2T), 5TONE(5T) or OFF. TALK: In standby status, press Talk key to enable and disable Talk around function. OFF: No function. 9 Memory Banks 10 memory banks are available for memory channel assignments to ease in operation of the 5888UV III tri-band radio. You can enable one bank or multible banks through the radio itself. key to enter function menu. ASSiGninG A chAnnel to A MeMoRy bAnk 1. Select memory channel to assign to a memory bank. 2. Press 3. Turn the main band selector knob to choose No. 56 menu. The LCD displays "BAK"

4. Press the main band selector knob to enter function setup. 5. Switch the main band selector knob to choose desired value. OFF: No bank assignment A, B, C, D, E, F, G, H, I, J to assign the selected bank. 6. Press the main band selector knob or key to store. 29 key to enter bank mode. chooSinG ActiVe bAnk 1. Select either left or right band in memory mode. 2. Press 3. Bank numbers show in the position of channel number. If a channel number is not assigned, a bank "--" will show; otherwise the assigned bank of that channel will show. 4. Rotate the selector knob to choose desired bank to view. 5. Press You can now view or scan channels in choosen bank. 6. Press memory view. key to confirm. Radio will swich to chosen bank. key two times to cancel bank view and return to key to enter function menu. bAnk linkinG Memory banks can be linked together for expanded scanning or viewing. 1. Press 2. Turn the main band selector knob to choose No. 57 menu. The LCD displays "BALK". 3. Press the main band selector knob to enter function setup. 4. Switch the main band selector knob to choose which banks to link. The following menus allow you to link banks A-J. ON/OFF: Select ON to turn on Bank Linking, OFF to turn off Bank Linking Menu 58 Bank A Link ON /OFF Menu 59 Bank B Link ON /OFF Menu 60 Bank C Link ON /OFF Menu 61 Bank D Link ON /OFF Menu 62 Bank E Link ON /OFF Menu 63 Bank F Link ON /OFF Menu 64 Bank G Link ON /OFF Menu 65 Bank H Link ON /OFF Menu 66 Bank I Link ON /OFF Menu 67 Bank J Link ON /OFF 5. Press the main band selector knob or key to store. 11 deFAult VAlue FoR FActoRy ReSuMe 5888UV III Left band 145.15MHz CH1: 144.000MHz CH2: 222.000MHz CH3: 420.000MHz Right band 435.15MHz CH1: 144.000MHz CH3: 420.000MHz VFO frequency Memory channel 1-750

--

5MHz Offset direction

--

Offset frequency Step size CTCSS code CTCSS frequency DCS code DCS group Output power Key Lockout TOT APO Squelch level 600KHz 12.5KHz

--

88.5Hz

--

017N HI OFF 3 OFF 4 tRouble ShootinG Problem

(a) Power is on, nothing appears on Display.

(b) Fuse is blown.

(c) Display is too dim.

(d) No sound comes from speaker.

(e) Key and Dial do not function.

(f) Rotating Dial will not change memory channel.

(g) PTT key is pressed but transmission does not occur. Maintenance 12 Possible Causes and Potential Solutions

+ and - polarities of power connection are reversed. Connect red lead to plus terminal and black lead to minus terminal of DC power supply. Check and solve problem resulting in blown fuse and replace fuse with new fuse. Adjust the Dimmer to higher level. Squelch is muted. Decrease squelch level. Tone or CTCSS/DCS squelch is active. Turn CTCSS or DCS squelch off. Key-lock function is activated. Cancel Key-

lock function. 30 Transceiver is in CALL mode or VFO mode. Microphone connection is poor. Connect microphone properly. Antenna connection is poor. Connect antenna properly. 13 Specifications Frequency Range General RX: 136~174MHz 220~260MHz 400~512MHz TX: 144~148MHz 222~225MHz 420~450MHz Number of Channels 750 channels Channel Spacing 12.5KHz Phase-locked Step 2.5KHz,5KHz,6.25KHz,8.33KHz,10KHz, 12.5KHz,15KHz,20KHz,25KHz. 31 Operating Voltage 13.8V DC 15%

Squelch Carrier/CTCSS/DCS/5Tone/2Tone/DTMF Frequency Stability 2.5ppm Operating Temperature -20~+60 Dimensions(WxHxD) 140(W)x50(H)x210(D)mm Weight about 1.38kg 12 Sensitivity

(12dB SINAD) Adjacent Channel Selectivity Audio Response Hum & Noise Audio distortion Audio power output Power Output Modulation Adjacent Channel Power Hum & Noise Spurious Emission Audio Response Audio Distortion Receiver 0.35V 60dB

+1~-3dB(0.3~2.55KHz) 40dB 5%

2W@10%

Transmitter 50W/25W/10W/5W(VHF1) 25W/15W/10W/5W(VHF2) 40W/25W/10W/5W(UHF) 11KF3E 60dB 36dB 70dB

+1~-3dB(0.3~2.55KHz) 5%

13 51 GRoupS ctcSS tone FRequency(hz) 62.5 77.0 91.5 107.2 127.3 151.4 167.9 183.5 199.5 225.7 254.1 67.0 79.7 94.8 110.9 131.8 156.7 171.3 186.2 203.5 229.1 Self Define 69.3 82.5 97.4 114.8 136.5 159.8 173.8 189.9 206.5 233.6 71.9 85.4 100.0 118.8 141.3 162.2 177.3 192.8 210.7 241.8 74.4 88.5 103.5 123.0 146.2 165.5 179.9 196.6 218.1 250.3 Attached Chart 14 1024 GRoupS dcS code 000 010 020 030 040 050 060 070 100 110 120 130 140 150 160 170 200 210 220 230 240 250 260 270 300 310 320 330 001 011 021 031 041 051 061 071 101 111 121 131 141 151 161 171 201 211 221 231 241 251 261 271 301 311 321 331 002 012 022 032 042 052 062 072 102 112 122 132 142 152 162 172 202 212 222 232 242 252 262 272 302 312 322 332 003 013 023 033 043 053 063 073 103 113 123 133 143 153 163 173 203 213 223 233 243 253 263 273 303 313 323 333 004 014 024 034 044 054 064 074 104 114 124 134 144 154 164 174 204 214 224 234 244 254 264 274 304 314 324 334 005 015 025 035 045 055 065 075 105 115 125 135 145 155 165 175 205 215 225 235 245 255 265 275 305 315 325 335 006 016 026 036 046 056 066 076 106 116 126 136 146 156 166 176 206 216 226 236 246 256 266 276 306 316 326 336 007 017 027 037 047 057 067 077 107 117 127 137 147 157 167 177 207 217 227 237 247 257 267 277 307 317 327 337 32 720 730 740 750 760 770 721 731 741 751 761 771 722 732 742 752 762 772 723 733 743 753 763 773 724 734 744 754 764 774 725 735 745 755 765 775 726 736 746 756 766 776 13 727 737 747 757 767 777 14 Attached Chart 340 350 360 370 400 410 420 430 440 450 460 470 500 510 520 530 540 550 560 570 600 610 620 630 640 650 660 670 700 710 341 351 361 371 401 411 421 431 441 451 461 471 501 511 521 531 541 551 561 571 601 611 621 631 641 651 661 671 701 711 342 352 362 372 402 412 422 432 442 452 462 472 502 512 522 532 542 552 562 572 602 612 622 632 642 652 662 672 702 712 343 353 363 373 403 413 423 433 443 453 463 473 503 513 523 533 543 553 563 573 603 613 623 633 643 653 663 673 703 713 344 354 364 374 404 414 424 434 444 454 464 474 504 514 524 534 544 554 564 574 604 614 624 634 644 654 664 674 704 714 345 355 365 375 405 415 425 435 445 455 465 475 505 515 525 535 545 555 565 575 605 615 625 635 645 655 665 675 705 715 346 356 366 376 406 416 426 436 446 456 466 476 506 516 526 536 546 556 566 576 606 616 626 636 646 656 666 676 706 716 347 357 367 377 407 417 427 437 447 457 467 477 507 517 527 537 547 557 567 577 607 617 627 637 347 657 667 677 707 717 33 A 1

. 1 6 0 4 2 6

InternalPhotos OPEN VIEW OF EUT-1 OPEN VIEW OF EUT-2 INTERNAL VIEW OF EUT-1 INTERNAL VIEW OF EUT-2 INTERNAL VIEW OF EUT-3 INTERNAL VIEW OF EUT-4 INTERNAL VIEW OF EUT-5 INTERNAL VIEW OF EUT-6 INTERNAL VIEW OF EUT-7 INTERNAL VIEW OF EUT-8 INTERNAL VIEW OF EUT-9 INTERNAL VIEW OF EUT-10 Part II OPEN VIEW OF EUT INTERNAL VIEW OF EUT-1 INTERNAL VIEW OF EUT-2 INTERNAL VIEW OF EUT-3 INTERNAL VIEW OF EUT-4

ExternalPhotos TOTAL VIEW OF EUT Part TOP VIEW OF EUT BOTTOM VIEW OF EUT FRONT VIEW OF EUT BACK VIEW OF EUT LEFT VIEW OF EUT RIGHT VIEW OF EUT Part TOP VIEW OF EUT BOTTOM VIEW OF EUT FRONT VIEW OF EUT BACK VIEW OF EUT LEFT VIEW OF EUT RIGHT VIEW OF EUT

FCCIDLabelLocation LAND MOBILE RADIO Model:5888UV III Brand: Anytone FCC ID: T4KAT5888UVIII Thisdevicecomplieswithpart15oftheFCC rules.Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause harmfulinterference,and(2)thisdevicemust acceptanyinterferencereceived,including interferencethatmaycauseundesired operation. WARNING:MODIFICATIONOFTHISDEVICETO RECEIVECELLULARRADIOTELEPHONESERVICE SIGNALSISPROHIBITEDUNDERFCCRULESAND FEDERALLAW

Qixiang Electron Science& Technology Co., Ltd Qixiang Building, Tangxi Industrial Zone, Luojiang Quanzhou, Fujian, China Tel: 86-592-22652998 Fax: 86-595-22656927 May 05.2016 To:

Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Subject: Attestation statement regarding the Land Mobile Radio frequency Applicant: Qixiang Electron Science& Technology Co., Ltd Qixiang Building, Tangxi Industrial Zone, Luojiang Quanzhou, Fujian, China TYPE OF QEUIPMENT: Scanning Receiver FCC ID: T4KAT5888UVIII Dear Sir or Madam I attest that the receiver is incapable of tuning, or readily being altered, by the user to operate bands allocated to the scanning receiver in FCC 15.121. Please contact the undersigned if you have any questions or need any further information. Regards Qixiang Electron Science& Technology Co., Ltd Signature:

Name, Job Title and Dept.: Ken Xu / Manager