FCC ID: 2AAJXQS-IQSKM Door Window with Impact Sensor

IQ SHOCK MINI-S QUICK INSTALL GUIDE STEP 1 CHOOSE INSTALLATION LOCATION STEP 2 DIP SWITCH CONFIGURATION Exterior Doors Sliding glass doors Windows SPECIFICATIONS Sensor: 2.5H x 1W x .5D Code outputs: tamper, tamper restore, alarm, alarm restore, low battery. Transmitter frequency: 319.5 MHz Supervisory keep-alive interval: 70 minutes. RF Peak field strength: typical 36000 uV/m at 3m UL/ULC listed for residential use only Operating Temperature: -5C~45C Relative Humidity: 5-95% Non-Condensing Storage Temperature: -25-70C Replace battery with exact replacement every 5 years with 3V CR2032 Lithium (x2). Two dip switches allow you to customize the behavior of this device:

DS#1 - Installer Test Mode:

ON:

- Calibrates accelerometer orientation.

- LED is Active for dialing in shock sensitivity with potentiometer.

- Please note, when test mode is enabled

(ON) the IQ Shock Mini will NOT transmit signals to the IQ Panel. This mode is only used for initial installation and calibration of the shock sensor. OFF: - Disables installer test mode. DS#2 - Reed Switch:

ON:

- Enables reed switch (must be ON for UL installations). OFF:

- Disables reed switch. Sensitivity Level:

CLOCKWISE:

COUNTER-

CLOCKWISE:

- More Sensitive

- Less Sensitive SENSITIVITY LEVEL MAX MIN LED MAGNET N O 2 1 DIP SWITCHES IMPORTANT NOTE:

The IQ Shock is intended to be installed on doors with or without glass inserts and on window frames but not on the actual glass surface. This is a quick guide for experienced installers only. Refer to http://dealers.qolsys.com (login required) STEP 3 REMOVE BATTERY TABS STEP 4 APPLY ADHESIVE STEP 5 MOUNT SENSOR &

MAGNET STEP 6 LEARN INTO PANEL 1 MAX ADD Place your panel in Auto Learn mode Open and close the case to tamper the device Customize name and settings as desired and and touch ADD STEP ADJUST SHOCK SENSITIVITY 7 Adjusting the Shock Sensitivity:

IMPORTANT: Calibrate the IQ Shock Minis accelerometer from the final mounting position by moving dip switch 1 to ON (enable installer test mode). While in this mode the LED will flash GREEN when the unit detects a pre-warn threshold. The LED will flash RED when it detects a shock level strong enough to trigger an alarm at the control panel. There are 5 total sensitivity settings and the LED will flash each time the sensitivity threshold is changed. Please note that no RF transmission from the sensor occurs during installer test mode. Gently hit (using the palm of your hand) the surface on which the device is installed. Gradually increase the pressure or turn the shock sensitivity adjustment dial clockwise with a small screwdriver until the desired response is obtained. Ensure that the device is not triggered by accidental vibration (e.g., wind, birds, window coverings) hitting the protected window or surface. Normal traffic or operation of the door/window should not trip the shock sensor. When testing the sensitivity of the unit, do not cause stress or damage to the mounting surface or to the glass. WARNING:

In order to avoid personal injury while testing sensitivity, do not apply pressure to glass inserts or windows. Move dip switch 1 to OFF (disable installer test mode) once shock sensitivity has been set to the desired level. Verify that the IQ Shock Mini properly communicates with the Panel. Document#: IQSM-QG Revision#: 02/14/23 Qolsys Product #: IQSM FCC ID: 2AAJXQS-IQSKM IC: 11205A-QSIQSKM UL/ULC NOTE:

The IQ Shock Mini - S has been listed by UL/ULC for residential applications only and in accordance with the requirements in the Standards UL 634 and UKLC/ORD-C634 for Door and Window Contact with supplementary Shock Sensor. The shock sensor is for supplementary detection only and not for primary protection of the surface and is not intended for use as a glass break detector. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas provoquer d'interfrences et (2) cet appareil doit accepter toute interfrence, y compris celles pouvant causer un mauvais fonctionnement de l'appareil.

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6452271.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case QS-IQSKM LABEL Label location Label Contents (Not as shown): Will be as indicated below:

FCC ID: 2AAJXQS-IQSKM IC : 11205A-QSIQSKM HVIN: IQ Shock Mini

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6452267.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Letter of Authorization and Anti- Drug Statement Applicant Name: Qolsys Inc. Address: 1919 S. Bascom Ave., Suite 600, Campbell, CA, 95008, USA Product Name: Door Window and Impact Sensor Model Number: IQ Shock Mini FCC ID: 2AAJXQS-IQSKM We authorize:

CETECOM Inc., to act on our behalf on all matters concerning the above named equipment. We declare that CETECOM Inc. is allowed to forward all information related to the approval project to the Federal Communications Commission and discuss any issues concerning the approval application. The applicant must certify that neither the applicant nor any party to the application is subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-

Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47 CFR 1.2002(b) for the definition of a "party" for these purposes. Does the applicant or authorized agent so certify? Yes I certify that I am authorized to sign this application. All of the statements herein and the exhibits attached hereto, are true and correct to the best of my knowledge and belief. In accepting a Grant of Equipment Authorization as a result of the representations made in this application, the applicant is responsible for (1) labeling the equipment with the exact FCC ID specified in this application, (2) compliance statement labeling pursuant to the applicable rules, and (3) compliance of the equipment with the applicable technical rules. If the applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC's technical requirements. Authorizing an agent to sign this application, is done solely at the applicant's discretion;

however, the applicant remains responsible for all statements in this application. If an agent has signed this application on behalf of the applicant, a written letter of authorization which includes information to enable the agent to respond to the above section 5301 (Anti-Drug Abuse) Certification statement has been provided by the applicant. It is understood that the letter of authorization must be submitted to the FCC upon request, and that the FCC reserves the right to contact the applicant directly at any time. Signature of Authorized Person Filing:

Printed Name: Mark Skeen Title: Vice President Date: 02-14-2023

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6452280.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Qolsys Inc. 1919 S. Bascom Ave, Suite 600 Campbell, CA 95008 Federal Communication Commission 7435 Oakland Mills Road Columbia, MD 21046 02-09-2023 Attestation Statement according to 2.911(d)(5)(i) and 2.911(d)(5)(ii) FCC ID: 2AAJXQS-IQSKM TO WHOM IT MAY CONCERN:

Hereby we certify that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Further we certify that, as of the date of the filing of the application, Qolsys Inc is not identified on the Covered List as an entity producing covered equipment. Sincerely,

(signature & company stamp) Qolsys Inc. 1919 S. Bascom Ave, Suite 600 Campbell, CA 95008 Mark Skeen 855-476-5797 Mark.j.skeen@jci.com For information on Covered equipment, refer:

986446 D01 Covered Equipment v01 FCC 22-84

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6452281.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Qolsys Inc. 1919 S. Bascom Ave, Suite 600 Campbell, CA 95008 Federal Communication Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA 03-30-2023 Attestation Statement according to 2.911(d)(7) FCC ID: 2AAJXQS-IQSKM TO WHOM IT MAY CONCERN:

We, Qolsys Inc., 1919 S. Bascom Ave, Suite 600; Campbell, CA 95008 with FCC Registration Number (FRN) 0022572226 Certifies that, as of the date of this filing of the application with the TCB, Qolsys Inc. is our designated US agent for service of process for the above referenced FCC ID. accepts to maintain an agent for no less than one year after the grantee has We, Qolsys Inc., terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. with FCC Registration Number (FRN) 0022572226 We, Qolsys Inc., Accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above referenced FCC ID. Sincerely

(signature & company stamp) Qolsys Inc. 1919 S. Bascom Ave, Suite 600 Campbell, CA 95008 Mark Skeen 855-476-5797 Mark.j.skeen@jci.com

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6452269.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21048 Date: 01-25-2023 Permanent Confidentiality Subject:

Request for FCC ID: 2AAJXQS-IQSKM To Whom It May Concern:

Qolsys Inc., In accordance with 0.457(d) and 0.459 of CFR 47, and KDB 726920, hereby requests permanent confidentiality for documents filed under the following exhibit types:

1. 2. 3. 4. Block Diagram Schematic Diagram Part List Operational Description Qolsys Inc. These items contain detailed system and equipment description and related information about the product which considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. Since this design is a basis from which future technological products will evolve, also feels that this information would be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. Qolsys Inc. cover letters, attestations, label document, test reports, RF exposure information (SAR and MPE reports) We are aware that exhibit types

, cannot be requested to be classified confidential and are thus subject to publication, as will be documents of all other exhibits types for which we have not requested a confidentiality classification. Best Regards, _______________________________ Signature Name: Mark Skeen Title: Vice-President Company Name: Qolsys Inc. Address: 1919 S. Bascom Ave, Suite 600, Campbell, CA 95008

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6452282.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21048 Date: 01-25-2023 Short Term Confidentiality Subject:

Request for FCC-ID: 2AAJXQS-IQSKM To Whom It May Concern:

Qolsys Inc., requests In accordance with 0.457(d) and 0.459 of CFR 47, short term confidentiality for documents filed under the following exhibit types:

hereby 1. 2. 3. 4. External Photographs Internal Photographs User / Instruction Manual Test Set-up Photographs until the product will be publicly announced. 180 days from grant issue date Short term confidentiality release date / period:

Qolsys Inc., These items contain detailed system and equipment description and related information about the product which considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. Since this design is a basis from also feels that this information would which future technological products will evolve, be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. Qolsys Inc., We are informed and aware of our obligation that we have to inform the involved TCB in written and in due time if we intend to market the product prior to the above specified confidentiality release date so that the short term confidentiality classification can be reset prior to product launch. RF exposure information (SAR and MPE reports) We are aware that exhibit types cover letters, attestations, label document, test reports,

, cannot be requested to be classified confidential and are thus subject to publication, as will be documents of all other exhibits types for which we have not requested a confidentiality classification. Best Regards, _______________________________ Signature Name: Mark Skeen Title: Vice-President Company Name: Qolsys Inc. Address: 1919 S. Bascom Ave, Suite 600, Campbell, CA 95008

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6452279.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Justification statement for Antenna To:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2AAJXQS-IQSKM Only radiated measurements are used for EUT with FCC ID: 2AAJXQS-IQSKM to show compliance with FCC limits for fundamental end spurious emissions. All measurements were performed radiated and therefore additional antenna gain documentation is not required. The detailed information for antenna as below shows:

Design Specifications Typical Antenna Type Phosphor Bronze Wire Antenna Part No.QS1138-840 Working Frequency Overall Dimensions 319.5 MHz 124 mm x 0.9 mm Sincerely Yours, by / on: 03/21/2023

(signature / date) Mark Skeen

(print name) title:

Vice President on behalf of: Qolsys Inc. Telephone & Email:

1-855-476-5797 & mark.j.skeen@jci.com