FCC ID: 2AAJXQS-SRF319H Security Radio Card

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6106197.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Detailed Module Integration Details FCC: 2AAJXQS-SRF319H IC: 11205A-QSSRF319H Regulatory Module Integration Instructions This module has been granted modular approval for mobile applications. OEM integrators for host products may use the module in their final products without additional FCC certification if they meet the following conditions. Otherwise, additional FCC approvals must be obtained. The host product with the module installed must be evaluated for simultaneous transmission requirements. The users manual for the host product must clearly indicate the operating requirements and conditions that must be observed to ensure compliance with current FCC RF exposure guidelines. To comply with FCC regulations limiting both maximum RF output power and human exposure to RF radiation, the maximum antenna gain including cable loss in a mobile-only exposure condition must not exceed 2dBi. The Radial antenna provided with this device has a 1.94 dBi peak gain. A label must be affixed to the outside of the host product with the following statements:

This device contains: FCC: 2AAJXQS-SRF319H IC: 11205A-QSSRF319H The final host / module combination may also need to be evaluated against the FCC Part 15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device. If the final host / module combination is intended for use as a portable device (see classifications below) the host manufacturer is responsible for separate approvals for the SAR requirements from FCC Part 2.1093 and RSS-102. Device Classifications Since host devices vary widely with design features and configurations module integrators shall follow the guidelines below regarding device classification and simultaneous transmission and seek guidance from their preferred regulatory test lab to determine how regulatory guidelines will impact the device compliance. Proactive management of the regulatory process will minimize unexpected schedule delays and costs due to unplanned testing activities. The module integrator must determine the minimum distance required between their host device and the users body. The FCC provides device classification definitions to assist in making the correct determination. Note that these classifications are guidelines only; strict adherence to a device classification may not satisfy the regulatory requirement as near-body device design details may vary widely. Your preferred test lab will be able to assist in determining the appropriate device category for your host product and if a KDB or PBA must be submitted to the FCC. Note, the module you are using has been granted modular approval for mobile applications. Portable applications may require further RF exposure (SAR) evaluations. It is also likely that the host / module combination will need to undergo testing for FCC Part 15 regardless of the device classification. Your preferred test lab will be able to assist in determining the exact tests which are required on the host /

module combination. FCC Definitions Portable: (2.1093) A portable device is defined as a transmitting device designed to be used so that the radiating structure(s) of the device is / are within 20 centimeters of the body of the user. Mobile: (2.1091) (b) A mobile device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitters radiating structure(s) and the body of the user or nearby persons. Per 2.1091d(d)(4) In some cases (for example, modular or desktop transmitters), the potential conditions of use of a device may not allow easy classification of that device as either Mobile or Portable. In these cases, applicants are responsible for determining minimum distances for compliance for the intended use and installation of the device based on evaluation of either specific absorption rate (SAR), field strength, or power density, whichever is most appropriate. Simultaneous Transmission Evaluation This module has not been evaluated or approved for simultaneous transmission as it is impossible to determine the exact multi-transmission scenario that a host manufacturer may choose. Any simultaneous transmission condition established through module integration into a host product must be evaluated per the requirements in KDB447498D01(8) and KDB616217D01,D03 (for laptop, notebook, netbook, and tablet applications). These requirements include, but are not limited to:

Transmitters and modules certified for mobile or portable exposure conditions can be incorporated in mobile host devices without further testing or certification when:

The closest separation among all simultaneous transmitting antennas is >20 cm, Or Antenna separation distance and MPE compliance requirements for ALL simultaneous transmitting antennas have been specified in the application filing of at least one of the certified transmitters within the host device. In addition, when transmitters certified for portable use are incorporated in a mobile host device, the antenna(s) must be >5 cm from all other simultaneous transmitting antennas. All antennas in the final product must be at least 20 cm from users and nearby persons. OEM Instruction Manual Content Consistent with 2.909(a), the following text must be included within the users manual or operator instruction guide for the final commercial product. Operating Requirements and Conditions:

The design of SRF319-4 Module complies with U.S. Federal Communications Commission (FCC) guidelines respecting safety levels of radio frequency (RF) exposure for Mobile devices. FCC ID:

This device contains: FCC: 2AAJXQS-SRF319H Note: In the case where the Host / Module combination has been re-certified the FCCID shall appear in the product manual as follows:

FCC ID: 2AAJXQS-SRF319H Mobile Device RF Exposure Statement:

RF Exposure This module operates under Part 15, Subpart C (15.249) and Subpart B, Class B, which is exempt from RF exposure evaluation owing to the very low operating power. Caution Statement for Modifications:

CAUTION: Any changes or modifications not expressly approved by Qolsys Inc. could void the users authority to operate the equipment. FCC Part 15 Statement (Only Include if FCC Part 15 is Required on the End Product):

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Relocate the device Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer for help. IC Compliance:

IC No.: 11205A-QSSRF319H This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, (2) this device must accept any interference, including interference that may cause undesired operation of the device and (3) the device incorporating this module shall be tested for compliance with Industry Canada RSS standards. Cet appareil est conforme aux normes dexemption de licence RSS dIndustry Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer dinterfrence, (2) cet appareil doit accepter toute interfrence, notamment les interfrences qui peuvent affecter son fonctionnement et (3) l'appareil incorporant ce module doit tre test pour sa conformit aux normes RSS d'Industrie Canada. CAN ICES-3 (B)/NMB-3(B) This radio transmitter 11205A-QSSRF319H has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Cet metteur radio 11205A-QSSRF319H a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antennes rpertoris ci-dessous, avec le gain maximal autoris indiqu. Les types d'antenne non inclus dans cette liste qui ont un gain suprieur au gain maximum indiqu pour tout type rpertori sont strictement interdits pour une utilisation avec cet appareil. This device is to be used only with the Radial Antenna provided by Qolsys that is packaged with it. This antenna has a Peak gain of 1.94 dBi providing an Omni Antenna pattern.

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6106198.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Qolsys SRF319H Module

(HVIN: SRF319H) General Applications:

The Qolsys SRF319H Module features the Si4463 which is a low power transceiver silicon from SiLabs, capable of providing air interface to and compatibility with devices. Qolsys Security host devices (final products) that integrate this module will gain compatibility with a variety of Interlogix devices as well as Qolsys S-line devices for security: Door/Window sensors, motion detectors, glass sensors etc. 1 Installation and Operation:

The module has a simple 8 pin header interface for power, reset, and UART connections. The mounting screw is required for mechanical stability and to ensure a robust ground connection. The module has a u.fl connection intended for Antenna connection for connection to the final product antenna tuned to operate at the 319.5 MHz frequency. Do not place any large pieces of metal around or near the antenna, as it will inhibit performance. This module is intended to be installed in Qolsys or its affiliates final products which is intended to be a minimum of 20 cm or greater away from user in normal operation. The Qolsys SRF319H Module operates at 319.5 MHz with an output power set at 0 dBm with trace and filter loss is approx.. 1.3 dbi. Data and protocol specifications are beyond the scope of this document. Please contact Qolsys for the technical specifications. It is intended for use with the Radial Antenna as detailed in the SRF319H Antenna document Peak Gain 1.94 dBi. Integration Instructions:

The Qolsys SRF319H Module is installed in the Qolsys final product using an 8-pin connector with Pin Configuration as detailed below and secured in place by a screw and connection to the Qolsys host ground plane. The Module is installed in Qolsys products and is only operable by Qolsys host systems designed to communicate with this device. It is intended to connect to the host antenna using the u.Fl 2 connector. Qolsys Host device will typically receive a heartbeat signal which is a pulse (non-continuous) from a paried device (i.e. door contactor or the like) but does not typically transmit a heartbeat. Our product is considered transmitter activated automatically. In the rare situation where our device transmits an internal heartbeat (supervisory) to a device, the heartbeat signal transmission is once every 90 minutes, but for commercial applications may be as much as once every minute maximum and may not be modified. The Qolsys host device is the only device than can start/stop transmission or receiving mode of the module. Careful matching of the antenna to the 319.5 Mhz Frequency of this device should be conducted in the host and compliance with FCC and ISED requirements shall be determine as part of the Host (Final product) system. The Qolsys host system may not alter the firmware of the SRF319H Module without permission and approval of the Qolsys including when applicable obtaining a Class II permissive change to the SRF319H FCC approval. Pin Configuration:

3.3 v SRF Rx SRF Tx 1 5 2 6 3 7 4 8 SRF RST SRF Wake Not Used Not used FCC Compliance:

FCCID: 2AAJXQS-SRF319H This device complies with part 15 of the FCC Rules. Operation is subject to the following three conditions: (1) This device may not cause harmful interference, (2) this device must accept any interference received, including interference that may cause undesired operation, and (3) the device incorporating this module shall be tested for compliance as part 15 subpart B digital device and as receiver using FCC or SDoC procedures. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. 3 Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. IC Compliance:

IC No.: 11205A-QSSRF319H This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, (2) this device must accept any interference, including interference that may cause undesired operation of the device and (3) the device incorporating this module shall be tested for compliance with Industry Canada RSS standards. Cet appareil est conforme aux normes dexemption de licence RSS dIndustry Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer dinterfrence, (2) cet appareil doit accepter toute interfrence, notamment les interfrences qui peuvent affecter son fonctionnement et (3) l'appareil incorporant ce module doit tre test pour sa conformit aux normes RSS d'Industrie Canada. CAN ICES-3 (B)/NMB-3(B) This radio transmitter 11205A-QSSRF319H has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Cet metteur radio 11205A-QSSRF319H a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antennes rpertoris ci-dessous, avec le gain maximal autoris indiqu. Les types d'antenne non inclus dans cette liste qui ont un gain suprieur au gain maximum indiqu pour tout type rpertori sont strictement interdits pour une utilisation avec cet appareil. This device is to be used only with the Radial Antenna provided by Qolsys that is packaged with it. This antenna has a Peak gain of 1.94 dBi providing an Omni Antenna pattern. Warranty Information:

IMPORTANT! Changes or modifications not expressly approved by Qolsys Inc. will void the users authority to operate the equipment, as well as warranty for the product. 4

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6106202.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case SRF319H LABEL SRF319H Label

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6106199.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Date: 6/21/2022 UL LLC 12 Laboratory Dr. Research Triangle Park, NC 27709 USA To whom it may concern:

I, the undersigned, hereby authorize UL LLC to act on our behalf in all manners relating to application for equipment authorization of SRF Radio Card, Model SRF319H, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL LLC as our representative, we still recognize that we are responsible to:

a) fulfill the requirements for the scope of certification requested, including implementing any appropriate changes requested by UL Verification Services Telecommunications Certification Body (TCB) and / or the FCC;

b) supply any and all information needed for the evaluation of the products for which certification is sought;

c) make claims regarding certification only in respect of the scope for which certification has been granted;

d) not use our product certification in such a manner as to bring the TCB or FCC into disrepute and to not make any statement regarding product certification which the TCB or FCC may consider misleading or unauthorized;

e) discontinue use of all advertising matter that contains any reference thereto and complies with any and all actions required by the FCC upon suspension or cancellation of certification;

f) use certification only to indicate that products are certified in conformity with specified standards;

g) endeavor to ensure that no certificate or report or any part thereof is used in a misleading manner, and any copies of the grants/certificates shall be reproduced in their entirety;

h) comply with the requirements of the TCB and FCC, including the use of marks and label information prescribed for the scope of certification, when making reference to product certification in communication media such as documents, brochure or advertisements;

i) comply with the requirements for certification, supply any information needed for evaluation of products to be certified and, where applicable, make provision for the participation of observers;

j) ensure that products marketed under the scope of the requested certification continue to comply with the certification requirements;

k) provide a sample of a production unit for testing within 30 days of the request should this product be selected as part of either the TCBs or the FCCs market surveillance requirements;

l) keep a record of all complaints relating to products compliance with requirements of relevant standard; make records available to UL or FCC when requested; take appropriate action with respect to such complaints and any deficiencies found in the product that affect compliance with requirements for certification; document the actions taken with respect to complaints and/or deficiencies;

m) inform the TCB immediately of any changes that may affect its ability to comply with the certification requirements. This authorization is valid until Dec. 31, 2022 or until written notice from Qolsys Inc whichever occurs earlier. Sincerely Yours, by / on:

______ _06/21/2022

(signature / date) Mark Skeen

(print name) title:

Vice President on behalf of: Qolsys Inc.

(company name) Telephone & Email: 1-855-476-5797 & mark.j.skeen@jci.com

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6106200.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Date: 6/21/2022 Attn: FCC Office of Engineering and Technology / UL Verification Services TCB Subject:

Request for Confidentiality FCC ID:

2AAJXQS-SRF319H To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation (Operational Description) Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 180 days from grant issue date:

External Photos Excluding FCC Label Location User Manual Internal Photos It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards _______________________________ Signature Name: Mark Skeen Title: Vice-President Company Name: Qolsys Inc. Address: 1919 S. Bascom Ave, Suite 600, Campbell, CA 95008

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6106201.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Applicant/Grantee Qolsys Inc. FCC ID:

2AAJXQS-SRF319H Request for Modular Approval Request for Limited Modular Approval Requirements EUT Conditions Section 15.212 Modular Transmitters Single Modular Approval Requirements Comply

(Y/N) Shielding is provided by a metal shield over circuitry. Y Y Y N All modulation and data inputs are buffered by circuitry on the transmitter chip. Si4463 Transmitter provides its own LDO voltage regulators for core operation. From Si4463 Datasheet, Section 9: " +1.8 to +3.6 V Supply Voltage Input to Internal Regulators."

External antenna The antenna is permanently attached (secured by bracket to final product during installation). Additionally it is connected via u.fl connector and only installed at factory (i.e. not intended for user replacement or installation).. Testing was performed with the module extended outside of the host on a special extender board, as shown in the test setup photos. Y 1 2 3 4 5 The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. The modular transmitter must have its own power supply regulation. The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). The professional installation provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, Y Module will have its own permanently affixed label displaying its FCC-ID. When installed inside another device, module label cannot be seen. Therefore, the host device will also display a label referring to the enclosed module. 6 unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i)). The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number.

(A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following:

Contains Transmitter Module FCC ID: XYZMODEL1 or Contains FCC ID: XYZMODEL1. Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization.

(B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following:

Contains FCC certified transmitter module(s). Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. 7 8 The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. The module complies fully with the operating requirements of Part 15 Subpart C (15.231) as demonstrated in the test report exhibit. Y Shielding is provided by a metal shield over circuitry. Y A limited modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the transmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is always ensured.