FCC ID: 2AAJXQS-ZWAVE700 Z- Wave 700 Card

Qolsys Z-wave-700 Card General Applications:

The Qolsys Z-wave 700 card features the EFR32ZG14 modem, which is capable of providing an air interface to, and compatibility with Z-wave devices. Installation and Operation:

It is recommended to secure the module to a large ground plane using the mounting hole and header pins. Do not place any large pieces of metal around or near the antenna, as it will inhibit performance. The Qolsys Z-wave 700 card operates at the 908.42MHz. Data and protocol specifications are beyond the scope of this document. Please contact Qolsys for the technical specifications. 1 FCC Compliance:

FCCID: 2AAJXQS-Zwave700 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. IC Compliance:

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux normes dexemption de licence RSS dIndustry Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer dinterfrence et (2) cet appareil doit accepter toute interfrence, notamment les interfrences qui peuvent affecter son fonctionnement. CAN ICES-3 (B)/NMB-3(B) Warranty Information:

IMPORTANT! Changes or modifications not expressly approved by Qolsys Inc. could void the users authority to operate the equipment, as well as warranty for the product. 2

1 : 1 3 : 1 B MODEL Number: QS-ZWAVE700 FCC ID: 2AAJXQS-ZWAVE700 IC ID: 11205A-QSZWAVE700 Label Location MODEL Number: QS-ZWAVE700 FCC ID: 2AAJXQS-ZWAVE700 IC ID: 11205A-QSZWAVE700 Note. 1. Material: White PET 50#

2. Adhesive: Acrylic adhesive(0.05) 3. Color: Background: White Text : Black 0.5R*4 15+0.2mm MODEL Number: QS-ZWAVE700 FCC ID: 2AAJXQS-ZWAVE700 IC ID: 11205A-QSZWAVE700 24+0.2mm Vesta_ Z-Wave Card Label See Note 3C0383800-600-G Vesta_ Z-Wave Card Label 3C0383800-600-G 1:1 B

Federal Communications Commission Authorization and Evaluation Division DATE: 2020-20-1 Confidentiality Request regarding application for certification of FCC ID: 2AAJXQS-

ZWAVE700 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request long term confidential treatment of information accompanying this application as outlined below:

Exhibit Type Schematics Block Diagram Operational Description File Name 2AAJXQS-ZWAVE700_FCCID_Schematics.pdf 2AAJXQS-ZWAVE700_FCCID_BlockDiagram.pdf 2AAJXQS-ZWAVE700_FCCID_OperationalDescription.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely,

(Mark Skeen)

(VP Life Safety and Compliance) Qolsys Inc. 1900 The Alameda Suite 420 San Jose, CA. 95126 Qolsys.com (855) 4-QOLSYS

Qolsys Janurary 21, 2020 Federal Communications Commission 445 12" Street SW Washington, DC 20554 Subject: Limited Agency Agreement Qolsys Inc. FCC ID: 2AAJXQS-ZWAVE700 To Whom It May Concern:

We, Qolsys Inc., hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number 244/JXQS-ZWAVE700 under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is December 16, 2019. The Limited Agency Agreement expires on March 12, 2020, unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, MO~

Mark Skeen VP Life Safety & Compliance

Qolsys RE FCC ID: 2AAJXQS-ZWAVE700 To the certification reviewer:

We are hereby applying for full modular approval of the above-referenced FCC ID, based on compliance with all of the criteria as detailed below. Sincerely, Mark Skeen VP Life Safety & Compliance Qolsys Inc. Part 15 Unlicensed Single Modular Transmitter Approval Justification per 15.212 Requirement per 15.212 reference modulation/data inputs (if such inputs are provided.

(i) The radio elements of the modular | Yes. Shielding is provided by a metal shield over transmitter must have their own RF | circuitry shielding. Gi) The modular transmitter must have buffered | Yes. All modulation and data inputs are buffered by circuitry on the transmitter chip. The modular transmitter must have its own power supply regulation.

(iii) Yes, EFR32ZG14 modem provides its own LDO voltage regulators for core operation. with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module.

(iv) The modular transmitter must comply with | Yes. The antenna is permanently attached. the antenna and transmission system requirements of 15.203, 15.204(b) and 15.204(c).

(v) | The modular transmitter must be tested in a | Yes. Testing was performed with the module stand-alone configuration, i.e., the module | extended outside of the host on a special extender must not be inside another device during | board, as shown in the test setup photos. testing for compliance with Part 15 parameters.

(vi) The modular transmitter must be equipped | Yes. Module will have its own permanently affixed label displaying its FCC-ID. When installed inside another device, module label cannot be seen. Therefore, the host device will also display a label referring to the enclosed module. Qolsys

(vii) The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. Yes. The module complies fully with the operating requirements of Part 15 Subpart C (15.249) as demonstrated in the test report exhibit.

(viii) The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. Yes. This module operates under Part 15, Subpart C

(15.249) and Subpart B, Class B, which is exempt from RF exposure evaluation owing to the very low operating power:

To Whom This May Concern, The user manual for the Z-wave 700 card (FCC: 2AAJXQS-ZWAVE700) that is being submitted, is a draft version. The final version of the user manual will be available and supplied with the sale of the Z-wave 700 card. Sincerely,

(Mark Skeen)

(VP of Life Safety and Compliance)