FCC ID: WDYQ1110501 GPS Lap Timer

Quick Start Guide Whats in the box?

01 Please check the following items are in the box. Charging for your LT8000GT 03 LT8000GT is with built-in lithium battery. Please use the USB-Type C cable for charging with compatible USB adapter. (Some fast charging PD adapter might not be compatible for LT8000GT) Circuit Race Mode 06 Drag Race Mode 07 NOTE

* It takes 4 hours charging time when the power of your LT8000GT is o. Fully charged battery of your LT8000GT would be used at least 14 hours continuously. LT8000GT GPS Lap Timer Orange LED light is ON: Device battery is charging. Green LED is ON: Device battery is full. Use the arrow key to select Select a Mode from the Quick Use the arrow key to select Select dierent Drag mode by Circuit Race Mode. Menu. Drag Race Mode. dierent conditions. Important Notice:

Battery life depends on the usage period and other condition such as temperature, or GPS signal. The usage time of the device might be less than the specication. 1 2 1 2 04 Quick Mount and holders (Bonus accessories) There are two 1/4 inches screw holes on LT8000GT. Qstarz oers the Bonus accessories for car and motorcycle. You can use the attached Qstarz quick mount / vehicle holder, or nd the standard 1/4 inches screw holders for your LT8000GT. LT8000GT GPS Racing Lap Timer Quick mount is easy to install for your LT8000GT Qstarz LT8000GT device Warranty Card+Qstarz Sticker USB Type-C cable Quick Start Guide BONUS ACCESSORIES Car Holder or Motorbike Holder Kit Jelly Case Step 1 Step 2 Step 3 Screw the quick Lock up the car Place the car sucking mount on the top or holder or bike holder holder on the bottom of your to the quick mount. window and lock up. LT8000GT. After GPS is xed, select one of Adjust the other settings. the nearby circuits. Compare by dierent customized settings. Review the Drag results after each run. 3 4 3 4 The functions of the Buttons 7 8 Mount LT8000GT / GPS external Antenna

(Optional accessories) 05 02 4 9 3 2 1 5 6 1 2 3 4 5 6 7 8 9 Power Key: Press to back to home menu. Hold 3 secs to power on/o LT8000GT. Enter Key: To enter/conrm the selected option. Arrow Keys: Use to move up, down, left, or right on the screen. Return / Cancel Key: Cancel the selected function or return to previous page. Race Key: Press this button to start the RACE recording. Type C USB connection: For charging and data transfer to QRacing PC. Device Reset/Restart key. Insert a pin to power o the device (Inside the protection cover). External GPS MCX jack: Located inside the protection cover. 1/4 inch screw hole: One on the back and the other one on the bottom of the device, which is for connecting to Quick Mount with Vehicle holder. For the best GPS signal performance, please place the device straight up and the upper of the device face up to the sky. Some electrical devices and window tint might interfere the GPS signal. Suggest to place your LT8000GT as below:

Vehicle Motorbike LT8000GT is already built-in extreme high frequency GPS antenna. In some conditions that the GPS signal of LT8000GT might be weak or obstructed. Using external antenna would be improved the GPS signal receiving. A MCX connector to LT8000GT B GPS magnet receiver. It can be located on the car roof or iron metal Adjust the appropriate Beacon Press the Race button to start width with longer than the width laptiming. You can start when of the track. the screen showing Ready 5 6 NOTE For the better performance of your Qstarz experience, please update to the latest version of your Qstarz software and rmware. LT8000GT is a GPS data logger device which using outdoor for the best GPS signal. GPS satellite signal would be obstructed by solid substance such as bridge, building, tunnel, and trees. Some window tint would obstruct the GPS signal. If your device is not able to auto-recognize the track you go, please update to the latest trackmap version. You can setup a custom track, or contact us to request new track by email (info@qstarz.com). LT8000GTs Regulatory information is shown on Setting > Regulatory Information. QRacing Mobile App ( Support iOS / Android ) 08 QRacing PC analysis sof tware 11 QRacing Web (QWS) Service Product Safety Notice 14 QRacing Web (QWS) is a new racing social media platform oering users sharing their racing life. QRacing Web is auto sync to QRacing App oering 17 QRacing App Store Google Play Please download QRacing app from iOS App Store or Google Play. QRacing PC sof tware is developed for motorsport advanced analysis. You can QRacing APP is an analysis application for motorsport. With racing GPS data, you can review and share the synced video. NOTE

* Check the supported versions of your device from Qstarz website.

* Download App and activate your QRacing account with internet connected. analyze the acceleration/ brake point, speed, and position to improve the driving performance. Session Record Decelerate Accelerate Speed Global Circuit Ranking and History sessions backup. https://qws.qstarz.com QRacing Web Connect LT8000GT to QRacing App 09 1 2 Turn on the Bluetooth function on your smartphone and start your QRacing App. 12 How to get the Sof tware key for QRacing PC Analysis sof tware Important Notice: Backup 15 The Bluetooth is enabled while your LT8000GT is power on. Register your own account from QRacing Web online. You will get a new Regularly back up and format the memory of the device would keep your QRacing sof tware key with your personal account. (https://qws.qstarz.com) device health and work as usual. 3 4 Connect LT8000GT device to your QRacing account after downloaded and registered the QRacing APP. Bind the serial number of your LT8000GT to your QRacing account by tapping Connect on Racer or Go page to Add Qstarz device. NOTE

* LT8000GT can do lap timing stand-alone without internet.

* LT8000GT can be connected to QRacing app by Bluetooth and doing lap timing at the same time when internet connected. Scan the QR code to read the registration instruction. NOTE

* Please BACKUP your data BEFORE format the memory of your LT8000GT, otherwise it might cause the data loss or damage. Use Wi-Fi for LT8000GT Download data to QRacing PC from LT8000GT Technical Specications 10 1 Sessions uploads to your QRacing account:

Select WIRELESS > Wi-Fi > "ON" to turn on the Wi-Fi wireless function on LT8000GT. Select Wi-Fi information and conrm the SSID and Password. Open QRacing App and connect Wi-Fi network to your QRacing account by tapping Racer > Connect > Wi-Fi Network Enter the SSID and Password. Select Join then nished the connection. Go to History> tap Download and select the sessions to upload. 2 3 4 5 Device updates:

1 Tap Connect > Wi-Fi network > LT8000GT SSID to check or update to the latest version when LT8000GT Wi-Fi is turned on. NOTE

* When Wi-Fi ON, some functions of LT8000GT might not be used. Please TURN OFF Wi-Fi connection to keep using lap-timing functions.

* During Wi-Fi transferring, DO NOT turn o Wi-Fi otherwise it might cause the data loss or damage.

* Wi-Fi function is not for surng internet. 13 16 Model : LT - 8000GT Download the latest QRacing PC analysis sof tware from Qstarz website. http://racing.qstarz.com/Products/Qracing/QRacing-History.html GNSS : 25Hz GPS / GLONASS / Galileo / Beidou

(Note: Must enter the QRacing sof tware Key for the rst time) Power o your LT80000GT, and use Qstarz USB Type-C cable to connect your device to the computer. During data is transferring, please DO NOT remove the USB cable. It might cause the les damage or lost. Display : 3.2 Color LCD (320x240px) Wireless : Bluetooth LE 5.0 + Wi-Fi 2.4 GHz Memory : 8 GB NOTE

* QRacing PC sof tware can only be installed within Microsof t Windows system.

* For more details please refer to QRacing Manual. Help > Users Manual Battery type and life : Rechargeable, lithium-ion, Up to 14 hours Sensor : Accelerometer and Gyroscope Antenna : Built in and external MCX plug Charging port : USB Type C Input : DC 5V, 750 mA Water rating : IPX7 water resistant Dimension and weight : 11.7 x 7.2 x 3.1 cm, 158 grams Operating / Charging temperature : - 10 to 60 C / 0 to 45 C High-temperature conditions might cause your device to change its behavior to regulate its temperature. Using your device in very hot conditions can permanently shorten battery life and cause damage. For safety purpose, please do not place your device might obstruct while driving / riding. Do NOT take apart the device otherwise the warranty would be invalidated. For more product information, please visit Qstarz website. https://qws.qstarz.com/Ocial/8000gt/

Federal Communications Commission Interference Statement FCC For Class B device:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

-Consult the dealer or an experienced radio/ TV technician for help. CAUTION:

Any changes or modications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. RF Exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.To comply with RF exposure compliance requirements, the device should be used as described in the manual. The device should not be used in other congurations. Declaration of Conformity (RE Directive 2014/53/EU) EU DECLARATION OF CONFORMITY The simplied EU declaration of conformity referred to in Article 10(9) shall be provided as follows:

Hereby, Qstarz International Co., Ltd. address at 6F2, No. 160, Ming Chuan E. Rd, Sec. 6, Taipei, Taiwan, declares that the radio equipment type LT8000GT GPS Lap timer is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://racing.qstarz.com CE RF exposure RF Exposure information This device meets the EU requirements (2014/53/EU) on the limitation of exposure of the general public to electromagnetic elds by way of health protection. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. When use is prohibited, such as while traveling in aircraft, or when asked to do so by authorities, power o LT8000GT to turn o the devices wireless transmitters. Android is a registered trademark of Google Inc. Apple is a trademark of Apple Inc., registered in the United States and other countries. The Bluetooth word and trademarks are owned by the Bluetooth SIG Inc. Wi-Fi is a registered trademark of Wi-Fi Alliance. Windows is a registered trademark of Microsoft Corporation in the United States and other countries. Other trademarks and trade names are trademarks of their respective owners. QSTARZ INTERNATIONAL CO., LTD. 6F-2, No. 160, Ming Chuan E. Rd., Sec. 6, Taipei 114, Taiwan, R.O.C. TEL / +886-2-2792-0061 EN Ver A 202208

OST Gz LT-8000Gr GPS LAP TIMER ar BCE en recims vos 1080 ers wneso ta ree sc HAUL AMM 0 8YYMXXXX 8YYMXXXX

GPS Lap Timer GPS Ets ee Model 328% : LT-8000GT Input Power &A SiH : DV 5V, 750mA FCC ID : WOYQ1110501 d - Db QSTARZ INTERNATIONAL CO., LTD. 6F-2, No. 160, Ming Chuan E. Rd., Sec. 6, Taipei 114, Taiwan, R.O.C. SURE: MDRRRNE BMRA e RR XXX-XXXXXK Eecaroooooovnx fe X Ow d - Db This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interfer-

ence, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Qstarz International Co., Ltd. 6F-2, No. 160, Ming-Chuan E. Rd., Sec. 6., Taipei, Taiwan, 114 Authorization Letter Date: August 25, 2022 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: WDYQ1110501 To Whom It May Concern:

We, the undersigned, hereby authorize the following person on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by DEKRA Testing and Certification Co., Ltd. on our behalf shall have the same effect as acts of our own. Agent Company name

: DEKRA Testing and Certification Co., Ltd. Address

: No. 26, Hwaya 1st Road., Guishan District, Taoyuan City, 33341, Taiwan Contact Name

: Stanley Wu Email

: stanley.wu@dekra.com We are therefore responsible for the contents of the application. Product description

: GPS Lap Timer Model No. Brand Sincerely,

: LT-8000GT

: Qstarz Signature Contact Name: Celine Chen Job Title: Product Manager Email: Celine@Qstarz.com

Qstarz International Co., Ltd. 6F-2, No. 160, Ming-Chuan E. Rd., Sec. 6., Taipei, Taiwan, 114 Confidential Request Letter Date: August 25, 2022 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for confidentiality FCC ID: WDYQ1110501 Long-Term Confidentiality Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Schematics Block Diagrams Theory of Operation Bill of Materials/Parts List Tune-up procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Short-Term Confidentiality (STC) Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request temporary confidential treatment of information accompanying this application as outlined below:

Internal Photos External Photos Users Manual Test Set-up Photos Justification: Due to market confidential, we ask for the short-term confidentiality. Planned Release Date STC:

If no date is given, 90 days from grant date will be used. Sincerely, Signature Contact Name: Celine Chen Job Title: Product Manager Email: Celine@Qstarz.com

Qstarz International Co., Ltd. 6F-2, No. 160, Ming-Chuan E. Rd., Sec. 6., Taipei, Taiwan Declaration Letter Date: September 2, 2022 FCC ID: WDYQ1110501 To Whom It May Concern:

We, Qstarz International Co., Ltd., hereby declared that the device does not support channel 12 ~ 13 in 2.4GHz band and any non-US channels in all the operational mode(s) for the following product. Should you have any enquires or comments, please have my best attention. Sincerely, Signature: ___________________________ FCC grantee contact person information. Name: Celine Chen Email: Celine@Qstarz.com

FCC E-Label Information GPS Lap Timer (Model NoLT-8000GT) Information to be displayed A. 1) The information that will be displayed on the e-label and information that will remain in the user manual is shown below:

Information FCC ID number DoC logo 15.19 statement (This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.) Class B Digital Device user manual statements*

Describe any other FCC regulatory information included in e-label DoC declaration Caution to the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment

* If the e-label includes information typically included in the manual then the e-label shall clearly differentiate between information required to be on the devices surface and information required to be in the manual refer to 784748 D02 e labelling v01 section II D 3(b) on E-label Yes Yes No In Manual No No Yes No No No No Yes Yes Yes Yes E-label screen are provided below:

B. Access to the required information on the e-label Users are able to access the information in no more than three steps in a devices menu. The actual steps are:

To access the e-label information, in the device, Choose SETTING Regulatory Information e-label page No special access codes or permissions are required. The information is stored on the device, no special accessories are required to access the information. Yes. Its stored. No special accessories are required. Users are provided specific instructions on how to access the information. The information to the user is provided in the user manual. C. Labeling for Importation and Purchasing Products utilizing e-labels are required to have a physical label on the product at the time of importation, marketing and sales. For devices imported in bulk and not packaged individually, a removable adhesive label or, for devices in protective bags, a label on the bags is acceptable for this purpose. Any removable label shall be of a type intended to survive normal shipping and handling and must only be removed by the customer after purchase. For devices imported already in individual packages ready for sale, the information may alternatively be provided on the package. It shall contain:

1. The FCC ID and the DoC logo 2. Any other information required by specific rule to be provided on the surface of the product unless such information is permitted to be included in the Users manual or other packaging inserts. The DoC logo is present on the product packaging. FCC ID and model number are present on the device back side. D. Other :

The above information must be programmed by the responsible party and the information must be secured in such a manner that third-parties cannot modify it. The e-label information is pre-programmed by the grantee. The user cannot modify the e-label information. All the applicable regulatory information required on the packaging or user instructions must be provided according to the rules even if it is displayed electronically. Yes. All are provided.