Standard Accessories Optional Accessories Be Familiar With The Machine Charging the Battery Pack Chinese/English Voice Prompt Radio Body Desktop Charger PTT Screen Display Scanning Monitoring VOX TOT Keyboard Lockout Power Display Busy Channel Lockout Power Saving Mode Low Battery Warning Voice Companding/Scrambling Function Programming Encryption Function Special Signaling 50 CTCSS/208 DCS USB Cable Power Key Antenna Display Screen Function Keys Speaker Earphone USB Charging Port Desktop Charger Connector 1.The battery is not charged in the factory,please charge the battery under the environmental temperature 540 before Belt Clip using. PTT transceiver during charging may affect correct charging. 2.After purchasing or long-term storage(more than two months), charging the battery for the first time can not reach its saturation capacity,repeat charge/discharge for twice or three times to make battery capacity achieve the best state. 3.Before charging,please power off the transceiver,using the 4.If the battery has been charged fully,please do not charge it again,otherwise the service life of the battery may be shorten or may be damaged. 5.If the service time is significantly reduced even after completely correct charging,the battery can not be used any more,please replace a new battery. Desktop Charger Connector Icons MENU OPERATION Functions Operation Functions Operation Functions Operation Technical Parameters 1.Short press keys to adjust the volume. Monitoring transceiver will stop transmission if this occurs.To stop the Companding 2.Short press key to switch to channel mode,then short press Long press key for two seconds to enter into the monitor alarm,release the PTT key and the transceiver will return to It is a function setting which prevents the inter-channel This function can be voice activated so the user doesnt have The function can prevent interference from other transceivers The transceiver has 50 CTCSS and 208 DCS, volume scanning channel lockout keys to adjust the channels. 3.PTT: press this button whenever you wish to talk with the user of the other radio. unlocking earphone earphone volume Functions Operation mode,release it to exit. VOX to press the PTT key. transmitting receiving alarm Scanning key to turn on/off the VOX. It is convenient for the user to search for calls from other channels.WhenSide Key 2 in the software is programmed to the scanning function,long press key for two seconds to enter into the scanning mode,the transceiver will start to scan with the current channel;Operate it again to exit. Keyboard Lockout Long press key to lock all buttons,operate it again to unlock. When VOX level in the software is selected,short press key twice to enter into the VOX mode,then short press key or Chinese/English Voice Prompt The transceiver has a manual switching function between the Chinese and the English.Switch to Channel 16,turn off the transceiver,then press both the power key and key and meanwhile turn on the transceiver to switch between the Chinese and English. Time Out Timer(TOT) Power Display The purpose of the TOT is to prevent any single person from Short press power key to display the current battery level. using a channel for an extended period of time.An alarm will sound if the transmission continues beyond the set time.The battery level Busy Channel Lockout using the same channel. Battery Power Saving If there is no signal or operation,the radio will reduce its power consumption.The battery power-saving function activates when the channel is unoccupied or has not been in operation. Low Battery Warning If the battery power falls to the predetermined value during transmission,the transceiver will give out a voice prompt,please charge in time. Scrambling It is a voice encryption mode which is different from sub audio. interference. CTCSS/DCS also non-standard subaudio can be programmed!
CDCSS Mode It is valid only when you program the CDCSS on the channels. This function has two selections: "normal signaling" and "special signaling".Normal Signaling refers to the CDCSS codes on the channels is ordinary codes,we cantalk toeach other with the same CDCSS;Special Signaling refers to the CDCSS codes on the channels is special processed codes.When the transceivers in one company are programmed the same frequency with the same CDCSS and special signaling,they can avoid the signal interferences from the other companies transceivers. Frequency Range Supply Power Memory Channel SPECIFICATIONS 462.5500-462.7250MHz 467.5500-467.7125MHz DC3.7V 22 Antenna Configuration Internal Antenna Work Mode Co/Differ-frequency Simplex Ground Method Dimension Communication Cathode 120.25314.5mm TRANSMITTER Output Power Modulation Mode Max.Frequency Deviation Sparious Radiation 3W/2W/0.5W 30.26dBm FM(F3E 2.5kHz 7.5W Preemphasis Character Per Octave 6dB Emission Current 1800mA RECEIVER 0.16V12dB SINAD Sensitivity Audio Power Audio Distortion Intermodulation Interference Resistance Receiving Current Standby Current 300mW 5%
60dB 300mA 20mA We May Change The Specifications For Technical Improvement Without Prior Notice. FCC Statement:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. RF Exposure Information (FCC SAR) :
RF Exposure Information (SAR) : The SAR limit of USA (FCC) is 1.6W/Kg averaged over one gram of tissue. Product Type: two way radio, model number: KD-C70Pro (FCC ID: 2AQX5KD-C70PRO) has also been tested against this SAR limit. The device was test for typical body-worn operations and head face up operations keep the Tracker at least 25mm from the face.when worn on body must be correct back clip for this product,Use of non-approved accessories may result in exposure levels which exceed the uncontrolled envirnomental RF exposure limits. RF Exposure Information (ISED SAR) :
The SAR limit of IC is 1.6W/Kg averaged over one gram of tissue. Product Type: two way radio, model number: KD-C70Pro (IC: 24229-KDC70PRO) has also been tested against this SAR limit. The device was test for typical body-worn operations and head face up operations keep the Tracker at least 25mm from the face.when worn on body must be correct back clip for this product,Use of non-approved accessories may result in exposure levels which exceed the uncontrolled envirnomental RF exposure limits. Le SAR de IC est limit 1.6W/Kg, avec une moyenne par gramme.Produits Type:two way radio, type: KD-C70Pro (IC: 24229-KDC70PRO) a galement t test pour la limite SAR.Ce dispositif est utilis pour tester des oprations d 'usure corporelle typiques et des oprations en direction du Haut de la tte, de manire maintenir une distance d' au moins 25 mm entre le traceur et le visage.