FCC ID: 2AUZJ-MN43 Two-way radio

ULTRA THIN TWO WAY RADIO USER MANUAL Basic Information Including Radio Body x1Battery x1Adaptor x1 Charging Cable x1, Belt Clip x1Hand Strap x1 User Manual x1 I Power On/Off III Push To Talk V Current Channel Broadcast VII Breathing Light Care and Cleaning Long press "Power On/Off" Key for 2 seconds to turn on/off the radio. Press "PTT Key / Side PTT Key" to transmit, release to exit. Long press "Channel + " for 1.5S to know the current channel. After standby for 10S, the breathing light is activate. It will lighting each 5S. 5 6 7 8 9 10 11 12 1 2 3 4 13 14 Basic Parameter Dimension: 130x52x21.5mm Weight: 80g Storage Channel: 14CH Operating Voltage: 3.3-4.2V DC Operating Temperature: -10~-40 Microphone PTT Key Breathing Light Speaker Antenna Side PTT Key Channel +

Channel -

Volume Key MIC Jack Earphone Jack USB Charging Port Power On/Off Battery Long press 2S Long press Long press 1.5S II Channel Selection IV Monitor Function VI Volume Adjust Short press "Channel +" to increase the channel number. Short press "Channel - " to decrease the channel number. Long press "Channel - " for 1.5S, then monitor function is activate, you can listen to the channel you selected whether someone is talking, if there is no signal, you will hear the sound of rustling. Toggle "Volume +" to increase the volume, toggle "Volume - " to decrease the volume. You will hear a beep sound when the volume is maximum or minumum. Volume Level: 0-7, you can set by programming software. Short press Long press 1.5S Toggle Channel List Channel 1 2 3 4 5 6 7 Frequency 462.5625 462.5875 462.6125 462.6375 462.6625 462.6875 462.7125 Frequency Model Model FRS FRS FRS FRS FRS FRS FRS Channel 8 9 10 11 12 13 14 467.5625 467.5875 467.6125 467.6375 467.6625 467.6875 467.7125 FRS FRS FRS FRS FRS FRS FRS Note: 8-14 channels must not exceed 0.5 W. Licensing Information VIII Scan Function Scan function is activate in No. 16 channel, stop to scan after exiting No.16 channel. IMPORTANT NOTE: This equipment has been tested and found to comply with the limits for a Class B digital, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful inter-

ference to radio or television reception, which can be determind by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the follwing measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation. This radio complieswith IEEE and ICNIRP exposure limits for General Population/Uncontrolled Environments RF exposure emvironment at operating duty factors of up to 50% and is authorized by the FCC for General Population use only. An appropriate warning lable is affixed to all units. In order to comply with RF exposure requirements, a minimum distance of 2.5 cm must be maintained when held-to-face, and body-worn operations are restricted to the approved original acessories (belt clip), a minimum distance of 0 cm. Do not use this device when antenna shows obvious damages. MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE PROHIBITED UNDER FCC RULES AND FEDERAL LAW. SERVICE SIGNALS IS To guarantee optimal performance as well as a long service life of the product, please follow the tips below. Do not puncture or scratch the product with hard objects. Do not place the product in corrosive agents, solutions or water. Do not handle the radio by its antenna or external microphone directly. When not in use, keep the accessory jacks covered with the protective caps. Power off the product, and remove the battery before cleaning. Clean up the dust and fine particles on the product parts with a clean and dry lint-free cloth or a brush regularly. Use a non-woven fabric with neutral cleanser to clean the keys, control knobs, and shell after long-time use. Do not use chemical preparations such as stain removers, alcohol, sprays or oil preparations. Make sure the product is completely dry before use.

35x48mm MODEL: MN-43. MADE IN CHINA FREQUENCY: FRS FCC ID: 2AUZJ-MN43 Attention: restricted to occupational use to satisfy FCC RF exposure limits. See the user ki manuial for operating requirements, FEC Y OE S/N: HD143000001 oc op 0s 09 Ht

Quanzhou Tenway trading Co.,ltd. Agent Authorization Company: Quanzhou Tenway trading Co.,ltd. Address: #303B, Building A, Chengzhou Industrial Zone,Baozhou Road, Fengze District, Quanzhou, Fujian, China Product Name: Two-way radio Model Number(s): MN-43, MN-41, MN-42, MN-44 Product Description: Two-way radio We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Name:

JIANG JI SHENG Company: Quanzhou Tenway trading Co.,ltd. Date: 2021-04-12

Quanzhou Tenway trading Co.,ltd. Apr.12, 2021 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject: Explanation of differences between product types FCC ID : 2AUZJ-MN43 Model Number: MN-43, MN-41, MN-42, MN-44 To Whom It May Concern:

We, The Quanzhou Tenway trading Co.,ltd. hereby declare that the model : MN-41, MN-42, MN-44 are identical with the model : MN-43, except the model name and shell design. Except for the different above, no other modification is performed. Sincerely, Signature:

JIANG JI SHENG Quanzhou Tenway trading Co.,ltd.

Quanzhou Tenway trading Co.,ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2021-04-12 Subject; Request for Confidentiality FCC ID: 2AUZJ-MN43 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure External Photos Test Setup Photos Internal Photos User Manual In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

OR For 45 days, pursuant to Public Notice DA 04-1705. For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely JIANG JI SHENG Quanzhou Tenway trading Co.,ltd.

Quanzhou Tenway trading Co.,ltd. Date: 13 April 2021 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA FCC ID: 2AUZJ-MN43 Subject: Declaration of compliance to the requirements of 15.121 We declare that, this scanning receiver is incapable of operating (tuning), or readily being altered by the users to operate, within the frequency bands allocated to the Cellular Radiotelephone Service in part 22 of this chapter (cellular telephone bands). This device will not be able to receive transmissions in the cellular telephone bands by means of clipping the leads of, or installing, a simple component such as a diode, resistor or jumper wire; replacing a plug-in semiconductor chip; or programming a semiconductor chip using special access codes or an external device, such as a personal computer. This device is also incapable of converting digital cellular communication transmissions to analog voice audio. This device is designed so that the tuning, control and filtering circuitry is inaccessible. Any attempts to modify the equipment to receive transmissions from the Cellular Radiotelephone Service will render the receiver inoperable. This scanning receiver rejects any signals from the Cellular Radiotelephone Service frequency bands that are 38 dB or lower based upon a 12 dB SINAD measurement. We are aware that the modification of this device to receive transmissions from Cellular Radiotelephone Service frequency bands will be considered to constitute manufacture of such equipment. This includes any individual, individuals, entity or organization that modifies one or more scanners. Any modification to receive transmissions from the Cellular Radiotelephone Service frequency bands voids the certification of the scanning receiver, regardless of the date of manufacture of the original unit. If you have any questions, please feel free to contact me. Thank you. Sincerely JIANG JI SHENG Quanzhou Tenway trading Co.,ltd.