FCC ID: WVTWOUXUN19 Two way Radio (GMRS Radio)

Thank you and congratulations on purchasing the most advanced GMRS Two-Way Radio & Scanner ever made. The WOUXUN KG-UV9G is built upon the trusted performance, proven design and quality manufacturing of the KG-UV9D(Plus) and KG-UV9P amateur radios. It has been modied to comply with FCC GMRS specications and regulations to deliver unparalleled recreational, EmComm and SHTF communications & scanning. ATTENTION Please read this entire manual addendum as it contains important safety and compliance information for the proper handling and operation of your new GMRS radio. The information in this addendum supersedes and highlights dierences between the enclosed original KG-UV9P manual and this new KG-UV9G model. COMPLIANCE Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with PART 15B of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. This device meets the requirements of FCC PART 15.121(b) for scanning receivers in the following frequency ranges (MHz): 76-108 / 108-136 136-180 / 230-250 / 350-400 / 400-512 / 700-824 / 849-869 / 894-960. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 2.5 cm between the radiator and your body. The antenna used for this device must not be co-located or operating in conjunction with any other antenna or transmitter. 1 The device is authorized to operate at a duty factor not exceed 50%

KG-UV9G GMRS Two-Way Radio Transceiver & Scanner FCC PART 95E Certied FCC ID: WVTWOUXUN19 FCC PART 95 Warning This device operates on GMRS (General Mobile Radio Service) frequencies, which require an FCC (Federal Communications Commission) license. You must be licensed prior to transmitting on these frequencies. Serious penalties could result for unlicensed use of GMRS frequencies in violation of FCC rules, as stipulated in the Communications Acts Sections 501 and 502 (amended). You will be issued a call sign by the FCC, which should be used for station identication when operating the radio on GMRS frequencies. You should also cooperate by engaging in permissible transmissions only, avoiding channel interference with other GMRS users, and being prudent with the length of your transmission time. To obtain a license or ask questions about the license application, contact the FCC at 1-888-CALL-FCC or go to the FCC's website: http://www.fcc.gov and request form 605. Station ID Your GMRS station call sign must be transmitted using voice in the English language, or with intl. Morse code telegraphy using an audible tone: (a) Following a single transmission or a series of transmissions; and (b) After 15 minutes and at least once every 15 minutes thereafter during a series of transmissions lasting more than 15 minutes. You may use a Unit # after your call sign. Feature Dierences The following features available in the original KG-UV9P have been removed or modied to comply with FCC GMRS regulations. Default Channel Programming Chart The following factory/default channels are restored after performing a RESET ALL function [MENU 61_RESET | ALL]. Cross-Band Repeater: Removed; Not allowed on GMRS. Shift Direction: GMRS repeaters are positive oset only.

+ Shift Direction: Allowed only on GMRS repeater pairs. Power Levels: Restricted on some frequencies per FCC. Ch. 1-7 (H) | Ch. 8-14 (L only) | Ch. 15-30 (H) L = 0.5 Watts | M = 2 Watts | H = 5 Watts Feature Additions & Improvements The following features have been added or improved upon from the original KG-UV9P. Scanning Advance: When scanning in TO or CO Scan Modes [MENU 28_SCREV], you can now rotate the Channel Knob in either direction to immediately advance/resume scanning when youve encountered an unwanted signal. See Scanning section on page 4 for more details. Basic Operation Key Presses: The PF2 & PF3 side-keys and several front panel keypad keys allow short and long presses to access primary & secondary functions (such as for the REV/SCAN functions see the Programmable Function Keys section on the reverse). A long-press involves holding down a key for about 12 seconds to activate the alternate key function, rather than a momentary short-press for the primary key function. CH #

CH Name RX Freq. TX Freq. TX CTCSS TX PWR 001 GMRS 01C 002 GMRS 02S 003 GMRS 03E 004 GMRS 04 005 GMRS 05 006 GMRS 06 007 GMRS 07 008 GMRS 08 009 GMRS 09 010 GMRS 10 011 GMRS 11 012 GMRS 12 013 GMRS 13 014 GMRS 14 015 GMRS 15C 016 GMRS 16S 017 GMRS 17E 018 GMRS 18 019 GMRS 19 020 GMRS 20T 021 GMRS 21 022 GMRS 22 023 GMRSr15C 024 GMRSr16S 025 GMRSr17E 026 GMRSr18 027 GMRSr19 028 GMRSr20T 029 GMRSr21 030 GMRSr22 462.5625 462.5625 141.3 H H 462.5875 H 462.6125 H 462.6375 H 462.6625 H 462.6875 H 462.7125 L 467.5675 467.5875 L L 467.6125 L 467.6375 L 467.6625 L 467.6875 467.7125 L H 462.550 H 462.575 H 462.600 462.625 H H 462.650 H 462.675 H 462.700 H 462.725 462.550 H H 462.575 H 462.600 H 462.625 H 462.650 462.675 H H 462.700 462.725 H 462.5875 210.7 462.6125 141.3 462.6375 141.3 462.6625 141.3 462.6875 141.3 462.7125 141.3 467.5675 141.3 467.5875 141.3 467.6125 141.3 467.6375 141.3 467.6625 141.3 467.6875 141.3 467.7125 141.3 141.3 462.550 210.7 462.575 141.3 462.600 462.625 141.3 141.3 462.650 141.3 462.675 141.3 462.700 141.3 462.725 467.550 141.3 210.7 467.575 141.3 467.600 141.3 467.625 141.3 467.650 467.675 141.3 141.3 467.700 467.725 141.3 Scan BW kHz 25 ON 25 ON 25 ON 25 ON 25 ON 25 ON 25 ON 12.5 ON 12.5 ON 12.5 ON 12.5 ON 12.5 ON 12.5 ON 12.5 ON 25 ON 25 ON 25 ON 25 ON 25 ON 25 ON 25 ON 25 ON 25 OFF 25 OFF 25 OFF 25 OFF 25 OFF 25 OFF 25 OFF 25 OFF C = CALL S = EARS/Safety E = EMER/Prepper T = Travel r = Repeater 2 Basic Operation (cont.) Function Menu: Press the MENU key to enter the function Menu. Use the Channel Knob, or 19 keys to select a function. Press MENU again to Edit the selected function. Use the same procedure to select or enter a value, then press MENU again to write any changes. Press MENU or EXIT to exit the function Menu. You can press EXIT any time to abort the current Menu operation without saving the change. Receiving: Turn the radio on by rotating the On/O/Volume Knob clockwise. Use the Channel Knob or keys to select the desired channel. Adjust the Volume as needed. Main: Toggle the active MAIN receiver with the BAND key. Single/Dual Receive: Toggle Single or Dual Receive Mode with the TDR (True Dual Receive) key. Sub-Band Muting: You can choose if you want audio on the Sub-Band Receiver muted (in TDR Dual mode) when a signal is received (even while scanning), when you transmit on the MAIN receiver, or both. Use [MENU 60_S-MUTE |

ALL, OFF, RX-MUTE, TX-MUTE, R/T MUTE] to toggle. Radio Controls & Indicators On/O/Volume Knob RX Green Signal & TX Red Transmit LED Indicators Channel Knob (bi-directional; no stops) Flashlight/Torch LED SMA-Female Antenna Connector PF / Programmable Function Keys Default Side-Key assignments:

PF1 (top round side-key):

Sub-Band Receiver TX (Transmit) PTT (large middle side-key):

MAIN Receiver TX (Transmit) PF2 short-press (3rd side-key):

Broadcast FM Radio (On/O) PF2 long-press (3rd side-key):

Flashlight/Torch (On/O) PF3 short-press (4th side-key):

Monitor (Open Squelch) PF3 long-press (4th side-key):

Stopwatch (Start/Stop/O-Reset) Transmitting: Choose a channel or frequency using the Channel Knob, or 19 keys. Short-press PF3 to conrm the channel is not in use, then again to mute. Hold the radio upright a few inches from your mouth with the display facing you. Press & hold the PTT key and speak at a normal, consistent volume. Release the PTT key to stop transmitting. CAUTION: Do NOT transmit without an antenna attached, with a damaged antenna, while touching the antenna, around explosives, or while refueling a vehicle. Operate only with batteries & chargers designed for this radio. Keypad Shortcuts 19: Freq/Chan Entry | FM Radio Mem.

| Menu Function Shortcuts BAND: Toggle Active MAIN Receiver TDR-V/M short-press: Single/Dual Receive Mode TDR-V/M long-press: VFO-FREQ/CH-#/FREQ/CH-NAME Modes MENU: Access Radio Functions | Edit/Save Menu Function EXIT: Exit Menu or Cancel Scanning

/SCAN short-press: REV | long-press: SCAN

#/LOCK short-press: FRQ/Save/Call (FM Radio) | long-press: LOCK

: Next/Prev. Channel/Function/Value RPT: short-press: BAND (in VFO) | long-press: Talk-Around/Direct 3 Scanning: The KG-UV9G GMRS radio oers single or dual FM Radio: The Commercial FM Radio feature tunes from 76 to receiver scanning with 3 dierent Scan Modes. SE Scan Mode: Scans until a signal strong enough to break squelch is received, then exits scanning, remaining on the current channel or frequency. TO Scan Mode: Scans until a signal is received, pauses for 5 seconds to preview the signal, then resumes scanning. CO Scan Mode: Scans until a signal is received, pauses until the signal ceases, then resumes scanning if no signal returns after 3 seconds. You can select the Scan Group assigned to each receiver independently. Use the BAND key to select the desired MAIN receiver, then set with [MENU 49_SCN-GP | 0110]. To start scanning channels or frequencies on the current MAIN band, long-press the key. To start scanning on the other receiver, press the BAND key to make it the MAIN receiver, then long-press the key. Use [MENU 60] to control Sub-Band Muting and the BAND key to select the primary (MAIN) scanning receiver. To stop scanning, switch to the desired receiver using the BAND key, then press any other key (other than the BAND key, such as EXIT or again). If you encounter an unwanted signal while scanning in the TO or CO Scan Modes, you can rotate the Channel Knob in either direction to immediately advance/resume scanning. 108 MHz in 100 kHz steps. It oers an IN FRQ VFO Mode with SE Scanning, Memory Save, and Memory Call functions with 20 dedicated memories. When operating the FM Radio, the MAIN &

Sub-Band receivers will be watching for active signals (if in TDR Dual Receive Mode) and will mute the FM Radio and play the MAIN or Sub-Band audio instead. When the signal ceases, the KG-UV9G will resume playing the current FM Radio station. Enter the FM Radio feature with a PF2 short-press. Short-

press again to exit the FM Radio feature. Toggle between IN FRQ/Save/Call modes with a # short-

press. Press the key to scan for an active FM Radio station. Use the 19 keys or Channel Knob to enter/select a frequency or memory channel in IN FRQ/Call modes, then press the MENU key to commit to the selection. Adding New Channels: You can add new simplex GMRS Tx/

Rx or other Scanner Rx-Only channels to your KG-UV9G with the keypad, as desired (add repeater channels via software only). Enter the VFO/FREQ Mode (see Keypad Shortcuts above). Use the Channel Knob, or 19 keys to select or enter the desired Rx frequency. Write the frequency as a new channel using [MENU 30_MEM-

CH | 001999]. Unused memory channels will display in red. Press MENU to commit writing to memory. TIP: You can use the free programming software to change the BetterSafeRadio display message to your own Call Sign! (16 chars.) Switch to Channel Mode and use the Function Menu to set any desired parameters, such as W/N, TXP, Rx-CTC/DCS, Tx-CTC/DCS, ROGER, BCL, SCAN-GRP & SCAN-ADD, etc. 4

@Hwouxun*

Model : KG-UV98G Frequency :GMRS ii S/N: TOBMP4740 FCC ID: WVTWOUXUN19 =: '$09001:2015 C py 1$014001:2015 MADE IN CHINA WARNING posh oan Sr Pate 1S DEVICE 7 RECEIVE CELLULAR RADIO TELEPHONE SER $ 1S PROHIBITED UNDER FCC BLILES ANE FEDERAL LAW

Company: Quanzhou Wouxun Electronics Co., Ltd. Add: Jiangnan High Technology Industry Park, No.928 Nanhuan Road, Quanzhou, Fujian, China Tel: 86-595-28051265 Fax: 86-595-28051267 E-mail: wouxun@wouxun.com

2020-07-02

Quanzhou Wouxun Electronics Co., Ltd. Two way Radio(GMRS radio) KG-UV9G, KG-UV9G(Plus), KG-UV9GX, KG-UV9GW. FCC ID: WVTWOUXUN19). These models are identical with the PCB design, components and electromagnetics compatibility characteristics. KG-UV9G has been tested by BACL.

Manager

Danny Chen

Company: Quanzhou Wouxun Electronics Co., Ltd. Add: Jiangnan High Technology Industry Park, No.928 Nanhuan Road, Quanzhou, Fujian, China Tel: 86-595-28051265 Fax: 86-595-28051267 E-mail: wouxun@wouxun.com FCC Confidential Authorization 2020-07-02 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: WVTWOUXUN19 In accordance with Sections 0.457 and 0.459 of the Commissions Rules, Quanzhou Wouxun Electronics Co., Ltd., hereby requests long-term confidential treatment of information accompanying this application as outlined below:

The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Block Diagram Schematics Operation Description BOM/Tune-up INTERNAL PHOTOGRAPHS Typed or Printed Name: Danny Chen Title: Manager Sincerely, Signature:

QA-FR-171-A

Company: Quanzhou Wouxun Electronics Co., Ltd. Add: Jiangnan High Technology Industry Park, No.928 Nanhuan Road, Quanzhou, Fujian, China Tel: 86-595-28051265 Fax: 86-595-28051267 E-mail: wouxun@wouxun.com DECLARATION 2020-07-02 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Declaration of compliance to the requirements of 15.121 FCC ID: WVTWOUXUN19 Dear Sir or Madam:

We declare that, this scanning receiver is incapable of operating (tuning), or readily being altered by the users to operate, within the frequency bands allocated to the Cellular Radiotelephone Service in part 22 of this chapter (cellular telephone bands). This device will not be able to receive transmissions in the cellular telephone bands by means of clipping the leads of, or installing, a simple component such as a diode, resistor or jumper wire; replacing a plug-in semiconductor chip; or programming a semiconductor chip using special access codes or an external device, such as a personal computer. This device is also incapable of converting digital cellular communication transmissions to analog voice audio. This device is designed so that the tuning, control and filtering circuitry is inaccessible. Any attempts to modify the equipment to receive transmissions from the Cellular Radiotelephone Service will render the receiver inoperable. This scanning receiver rejects any signals from the Cellular Radiotelephone Service frequency bands that are 38 dB or lower based upon a 12 dB SINAD measurement. We are aware that the modification of this device to receive transmissions from Cellular Radiotelephone Service frequency bands will be considered to constitute manufacture of such equipment. This includes any individual, individuals, entity or organization that modifies one or more scanners. Any modification to receive transmissions from the Cellular Radiotelephone Service frequency bands voids the certification of the scanning receiver, regardless of the date of manufacture of the original unit. Sincerely, Signature:

Title: Manager Typed or Printed Name: Danny Chen