FCC ID: 2AMIG-53317 S533 eScooter

Lets ride. CONTENTS Assembly Parts Included 2 Flyer App Usage 6 eScooter Controls 7 Charging Instructions 9 How To Ride 10 Folding 1 1 Specications Cleaning, Storage, & Battery Maintenance 15 Maintenance & Troubleshooting 16 Safety Guidelines 17 3 14 PAR TS INCLUDED FLYER S533 ALLEN WRENCH SCREWS HANDLEBAR CHARGER x1 309636 x4 309634 x1 309652 x1 Grey 309562 White 309563 Red 309564 2 ASSE MBLY Step 1 Rotate the tube to the vertical position. Ste p 2 Rotate the lever up while holding the tube in place. Step 3 Slide the locking sleeve down until it is fully seated. Warning! The lever must be completely locked in the upright position. 3 Step 4 Align the arrows on the handlebar and tube conectors. Once arrows are aligned, push them together rmly. Ste p 5 Slide the handlebar assembly into the tube. Push the handle bar assembly down until it is fully seated. Step 6 Install four screws to the top of the tube using the provided Hex wrench. Tighten the screws until they are snug. 4 Step 7 Check front air tire pressure. Inate air tire to 25 PSI. Warning! It is important to maintain proper air pressure in the front tire while riding. Do not overinflate or underinflate the tires. Overinflated tires may burst. Inflate your tires using an air source with a pressure gauge to avoid over inflation. 5 FLYER APP USAGE Connect to eScooter NEARBY FLYER SCOOTERS Scan FlyerS533-203271226 Dashboard 52%

B A T T E R Y L I F E MAX SPEED SETTING 1 2 3 9 M P H 1 2 M P H 1 6 M P H LOCK LIGHT Install the App Download the Flyer App using the App Store or on Google Play. Conn e ct to you r eS co oter Power on the eScooter and ensure your device has Bluetooth turned on. Click Connect to eScooter within the App and select your scooters serial number. The app will prompt you to review safe riding instructions. Review prior to riding. Flyer App Ca pa bilities The Flyer App allows you to change speed settings, turn the headlight on and off, lock the motor, access troubleshooting information, as well as update your rmware. 6 ES COOTER CONTROLS Powe r O n Hold down power button for 1 second. An audible "beep" will sound, and the dash will illuminate. Power Off Hold down power button for 2 seconds. An audible "beep"

will sound, and the dash will turn off. C h an ge S p ee d Setting Tap the power button twice to change speed setting. Reference speed mode indicator in the Dash Display section of the user manual. Hea dlight Tap the power button once to turn the headlight on and off. 7 DASH DISPLAY S PEED OMETER B ATTERY LEVEL SPE ED M ODE POWER BUT TON

(MULTIFUNCT IONA L) CHAN GE SPE ED: Tap power button twice to change speed setting. Beginner Max Speed = 9 mph

(15 km/h) I n te rme di ate Max Speed = 12 mph

(20 km/h) (Yellow) Adva nced Max Speed = 16 mph

(26 km/h) (Red) 8 CHAR GING INSTRUCTIONS WARNING: Do not attempt to charge if the charging port or power adapter is wet. WARNING: Only use charger specied by the manufacturer. MANUFACTURER: DONGGUAN ANGDI TECHNOLOGY CO LTD, MODEL: BC266420200 WARNING: Ambient temperature must be 32-104F (0-40C) during charging. The battery will not charge outside of these temperature limits. Plug 36V charger into charger port. Red Light = Charging Green Light = Fully Charged WARNING: Risk of Fire: Do not attempt to disassemble the charger. No user serviceable parts. 9 H OW TO RIDE T HROTT LE STO M P B RAK E BRAKE K ick to Start Place one foot on the deck, and use your other to kick the scooter forwards. While rolling, gently rotate the throttle to accelerate. B raki n g Use the stomp brake or the left thumb trigger on the handle bars to stop or decelerate the scooter. For more immediate braking use the stomp brake. Warning! Beginner riders should start by riding in Beginner mode (Max Speed: 9 mph (15 km/h)) 10 F OL D ING Step 1 Slide locking sleeve up. Step 2 Rotate the lever down while holding the tube upright to avoid sudden folding. Step 3 Rotate the tube 90 degrees until it is resting on the stomp brake. Step 4 Push the handlebar down until the latch engages with the slot on the top of the stomp brake. Once engaged, the latch remains fixed to the rear stomp brake for easy carrying. 11 UNF O LDING Step 1 Push down the stomp brake to free the handlebar latch. Ste p 2 Rotate the tube 90 degrees until it is in the upright position. Step 3 Rotate the lever 90 degrees to the upright position. Apply force to lock the lever into the locked position. Step 4 Slide the locking sleeve down until it is fully seated. 12 WARNING: Failure to follow unfolding instructions could result in unintentional folding. Ensure that the lever is upright and the sleeve is locked in place. 13 SPEC IFICATIONS Battery Battery Range Charging Flyer App Firmware Updates Connectivity IP Rating Lights Braking Wheels Top Speed Hill Grade Maximum Rider Wight Storage Temperature Operating Temperature 6.4 Ah (10S2P) Up to 15.5 mil 42VDC @ 2.0 Amp Charger iOS and Android Update Via Bluetooth Bluetooth Deck IP34, Battery IP67 Front LED headlight, rear LED taillight Electrical Regenerative and Stomp Brake Front = 7.9 Air Tire,Rear = 7.9 Semi Solid 16 mph 15% grade 220 lb (100 kg) 14 104F (-10-40C) 14 104F (-10-40C) CH AR GE R SPECIFICATIONS Input Voltage Charger Manufacturer: DONGGUAN ANGDI TECHNOLOGY CO LTD, Model: BC266420200 100-240AC, Output Voltage = 42VDC, Output Current: 2.0 Amps, Charging Temperature 32-104F (0-40C)

(Only Use Charger Provided) DI ME NSI ONS Length x Width x Height 38.6" X 18.1" X 45.1" (981 mm X 460 mm X 1145 mm) Product Weight 30.2 lb (13.7 kg) 14 CLE ANI NG AND STORAG E Use a damp cloth to wipe the mainframe clean. Hard to remove dirt can be scrubbed with a toothbrush, then cleaned with a damp cloth. Do not wash your Flyer S533 with alcohol, gasoline, acetone, or other corrosive solvents. These substances may damage the appearance and internal structure of your Flyer S533. Do not wash your Flyer S533 with a power washer or hose. WARNING: Make sure your Flyer S533 is powered OFF and the charging cable is unplugged before cleaning; otherwise you may damage the electronic components. Storage Temperatures: 14104F (-10-40C) BATTE RY PACK MAINTENA NC E Do not store or charge the battery at temperatures outside of the stated limits (see specications). Do not puncture the battery. Refer to your local laws and regulations regarding battery recycling and/or disposal. Charge the battery after each ride to avoid draining the battery completely. When used at room temperature (70F [22C]) the battery range and performance is best. WARNING: Do not attempt to disassemble the battery. Risk of re. WARNING: Do not ride when the ambient temperature is outside of the operation temperature (see specications). 15 MA INTENANCE AND TROUB LESH O OTIN G Visit yer.radioyer.com, email customerservice@radioyer.com, or call Radio Flyer customer service at 1-800-621-7613for additional assistance using, repairing, or maintaining your eScooter. For more information on recommended maintenance, please scan the QR Code. Troubleshooting How to change speed settings?

What is the maximum speed of the scooter?

How to turn on/off the headlight?

Why does my throttle not activate the scooter?

What is the proper air pressure level for the front tire?

What is the diameter of the front and rear tires?

I have a at fromt tire, what to do?

My charger light stays green when plugged in immediately after I nish a ride. My battery does not last 15.5 miles. Why does the battery life continue to get shorter over time?

After a crash or an incident, do not ride your eScooter until you have a certied and reputable mechanic inspect the eScooter. Any changes to the Flyer eScooter that are not specically approved by Radio Flyer Inc. could cause unsafe riding conditions and may void your warranty. Reference maintenance information and additional troubleshooting documentation via the Flyer App 16 I NSTR UCTIONS AN D SAFETY GU ID ELINES Before each use, conduct a basic safety inspection of the Flyer S533, including: (i) trueness of the wheels

& condition of tires; (ii) safe operation of all brakes and lights; (iii) good condition of the frame; (iv) sufficient battery charge power; and (v) any sign of damage, unusual or excessive wear, or other open and obvious mechanical problem/maintenance needs. Components shall be maintained and repaired in accordance with the manufacturers specications. Only the manufacturers authorized replacement parts should be used to service your Flyer S533. Do not modify the scooter as it will void your warranty and introduce potential safety issues. Read and understand all safety warnings listed on the product label. Recommended age: 16+ years old. Maximum weight: 220 lb (100 kg). No more than one rider should ride at a time. Risk of injury or death from loss of control, collisions, and falls. Helmets and other protective equipment are highly recommended and may be required by law. Product warranty can be found by visiting yer.radioyer.com. Comply with local laws and regulations when riding this product. Do not ride where prohibited. Ensure the intended area of operation is safe. Do not ride in the snow, in the rain, or on roads which are wet, muddy, icy, or that are slippery for any reason. Do not ride over obstacles. Avoid sharp bumps, drainage grates, and sudden surface changes. Avoid streets and surfaces with water, sand, gravel, dirt, leaves, and other debris. The scooter should not be used for racing, stunt riding, or other maneuvers. For shorter stopping distance, use the stomp brake in addition to the E-brake located on the handlebar. When traveling down hill or at high speeds the E-brake should not be used alone. 17 Avoid contact with moving parts. Ensure hands, feet, hair, clothing, and other body parts stay clear of moving parts like the motor or front wheel. ALWAYS keep both hands on the handlebar when riding. You should not ride the Flyer S533:

if under the inuence of alcohol or drugs, if you have a heart condition, are pregnant, have head, back, or neck ailments which limit your ability to ride safely, if you have any mental or physical conditions that may make you susceptible to injury or impair your physical dexterity or mental capabilities to recognize, understand, and perform all of the safety instructions and to be able to assume the hazards inherent with the Flyer S533. DO NOT attempt to disassemble the battery. Risk of re. Never modify the electrical system as this may result in a risk of electric shock, electrocution, or re. DO NOT attempt to charge a vehicle while wet. DO NOT ride or attempt to charge a vehicle that has been submerged in water or if there is risk of water intrusion into the battery compartment, even if the vehicle is no longer wet. Contact Radio Flyer for further instructions. To prevent electric shock when cleaning, remove the charger plug from the outlet and wipe vehicle with a dry cloth. Only use the charging cable provided by the manufacturer. Only store in dry areas. Never store in wet conditions. Devices are not intended for use at elevations greater than 2000 m above sea level. Prolonged Exposure to UV Rays, Rain and the Elements May Damage the Enclosure Materials, Store Indoors When Not in Use. 18 F E DE R AL COMMUNICATI ONS CO MMISSIO N (FCC ) COMPL IA NCE STATE MENT F OR USA This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy; if not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by powering the equipment off and on, the user is encouraged to try to correct the interference by using any of the following measures:

Reorienting or relocating the receiving antenna. Increasing the separation between the equipment and receiver. Connecting the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. Caution: Changes or modications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 19 HEADLIGHT H AND LEBA R TUBE LOCKI NG SLEEVE STOMP B R AKE LE VER CH ARG ING P ORT TA IL L IGH T K IC KSTAND Need help? Weve got you covered. Visit yer.radioyer.com for product assistance and frequently asked questions. Radio Flyer Inc. 6515 West Grand Avenue Chicago, IL 60707 United States

OSes M Net eeu) Rone Met esto Ua cao A]

re emis Sma RT Eso van) ETO een SSRI a UTR a ae oahu eg PAR) (Are eee |

O@ K econ co Caps er ic sec Perdew |

Peon Areas ia ETUC Ncnt ane CONE OU mT Ticartoe otic |

se sale Eel ee eines Beas eas poe) u) Meets pa we Ase ey) ou aK o1pey

Radio Flyer Incorporated Date: 11/02/2021 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2AMIG-53317 To whom it may concern:

We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou Branch and Kobe Jian in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Radio Flyer Incorporated This authorization is valid until further written notice from the applicant. Sincerely, Print Name: Timothy Stevens Title: Director of Engineering and Quality Signature:

On behalf of Company: Radio Flyer Incorporated Telephone: 773-797-9120 E-mail: tstevens@radioflyer.com

Radio Flyer Incorporated Confidentiality Request regarding application for FCC ID: 2AMIG-53317 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States To:

Regarding:

LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 15 days from the grant date, whichever is less. If the device is marketed within aforementioned days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Print Name: Timothy Stevens Title: Director of Engineering and quality Signature:

On behalf of Company: Radio Flyer Incorporated Telephone: 773-797-9120 E-mail: tstevens@radioflyer.com

a) b) c) d) e) f) g) SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name Radio Flyer Incorporated 6515 West Grand Ave, Chicago, Illinois 60707, United States Address Grantee Code FCC ID Contact Email Contact Phone Authorized Contact Name 2AMIG 2AMIG-53317 Timothy Stevens tstevens@radioflyer.com 773-797-9120 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Date: 11/02/2021 Applicant Signature:

Print Name:

Title:

Timothy Stevens Director of Engineering and Quality

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Applicant Declaration Rev:0.0